Tecom Co GCDBC1 Doorbell Camera User Manual 10010716A indd

Tecom Co Ltd Doorbell Camera 10010716A indd

User manual

RED WIREBLACK WIREDIODE16 VAC TRANSFORMERBLACK WIRE: TRANSFORMER WIRERED WIRE: CATHODE OF DIODESMART DOORBELLCAMERAPRINTER’S INSTRUCTIONS:GUIDE, INSTALL, QUICK,GC-DBC-1- P/N 10010716 A - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 17.000” X 11.000” - TOLERANCE: ± .125” - SCALE: 1-1 -FOLDING, FOLD 3 X TO FINAL SIZE 4.250” X 5.625” FINISH WITH LOGO SHOWING - SIDE 1 OF 2GC-DBC-1Installation InstructionsSystem DescriptionSMART DOORBELLCAMERADOORBELLTRANSFORMERCHIME BOXWiFi ROUTERWiFi COMMUNICATIONSCLOUDSMARTPHONEDoorbell Camera ComponentsPOWER DRILL WITH 1/4” BITWIRE STRIPPERS / CUTTERPHILLIPS SCREWDRIVERLEVEL0-M0.510502005005025010 50 250600 +-AC VOLT METERFLAT SCREWDRIVEROPTIONALPLIERSTools For InstallationDIODES FORCHIME BOX (2)USE LEVELING TOOLTO ALIGN CAMERAWITH LINE ONMOUNTING PLATEWIRE CONNECTORS (4)TORX WRENCHTORX SCREW SMART DOORBELLCAMERASMART DOORBELLCAMERA MOUNTINGPLATEPHILLIPS SCREWS (3)ANCHORS (3)SMARTPHONEEXISTINGDOORBELLPrepare for Installation• Go to existing doorbell location. • Use a Smartphone connected to the installations WiFi router to confi rm adequate signal strength (2 - 3 bars). Existing Doorbell Removal DISCONNECT WIRESFROM PUSHBUTTONDOORBELL• Remove existing doorbell pushbutton from location.• Disconnect wires from back of pushbutton.Measure Voltage0-M0.510502005005025010 50 250600 +-TEST VOLTAGEOF WIRES(REQUIRES15 TO 20 VAC)• Measure voltage of doorbell wiring with AC Volt Meter.• Doorbell camera works best with 15 to 20 VAC.Mounting Doorbell Camera PlateUPORUPUPUSE 1/4" (6.35mm) DRILL FORANCHOR HOLESSCREWS ONLY SCREWS & ANCHORS• Use mounting plate as guide to mark holes.Wiring Doorbell Camera1. TWIST THEN FEED WIRES INTOSHORT END OFCONNECTOR2. CRIMP WIRESWITH PLIERS ONSHORT END OF CONNECTOR CONNECTORSIN PLACE• Connect doorbell wires using weather- resistant wire connectors (included).System OverviewBLACK WIRE: TRANSFORMER WIRERED WIRE: CHIME BOX WIRECHIME BOX 16 VAC TRANSFORMERREAR TRANS FRONTREAR TRANS FRONT1 OPEN CHIME BOXCHIME BOX FRONT VIEW WITHOUT COVER2 INSTALL DIODE AS SHOWNDIODE(CATHODEON FRONTTERMINAL)IMPORTANT STEPInstalling Diode in Chime Box1234567Wiring Camera WITHOUT Chime ✔NOTE: Not compatible with electronic chimes ✔NOTE: It is recommended to TURN POWER OFF after verifying voltage.(OPTIONAL)
PRINTER’S INSTRUCTIONS:GUIDE, INSTALL, QUICK,GC-DBC-1- P/N 10010716 A - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 17.000” X 11.000” - TOLERANCE: ± .125” - SCALE: 1-1 FOLDING, FOLD 3 X TO FINAL SIZE 4.250” X 5.625” FINISH WITH LOGO SHOWING- SIDE 2 OF 2PUSH EXTRA WIRE INTOMOUNTING PLATE SLOTHANG DOORBELL CAMERA ONMOUNTING PLATE TAB TOPSSLIDE DOORBELLCAMERA “DOWN” Camera Installation to Mounting Plate Camera Faceplate Change-OutUSE FLATHEAD SCREWDRIVERTO REMOVE FACEPLATE FACEPLATE• Order Model GC-DBC-FP Faceplate Pak tochange out doorbell camera colors.• Use a fl athead screwdriver to remove plate. Doorbell Camera TroubleshootingMY DOORBELL APPQ: The APP doesn’t save photos or videos on my smartphone?A: Please ensure you have suffi cient memory on your smart device. Also ensure permissions are enabled on the APP to access the device memory.Q: I did not receive the Authentication Code when creating an account?A: Please check your email ‘junk’ box folder for an email from: mydoorbell@nortek.comNETWORKQ: The doorbell doesn’t register on the Wi-Fi network. Why?A: The smart doorbell camera may be out of range of your Wi-Fi network. Move the router or install a Wi-Fi extender. Note, the Doorbell Camera supports 2.4Ghz networks only.Q: The smart Doorbell Camera loses network connectivity?A: The smart Doorbell Camera may be out of range of your WiFi network. Move the router or install a Wi-Fi extender. STATUS COLORPowering Up Solid RedDiscovery Mode Flashing Green / RedConnecting to Network Flashing GreenConnected to Network (Normal Status)Solid GreenSession in Progress Flashing GreenNot Connected to Network Flashing Red (Slow)Firmware Update Flashing Red (Fast)Regulatory InformationThe GC-DBC-1 is certifi ed to comply with applicable FCC and IC rules and regulations governing RF and EMI emissions. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.FCC NoticeThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician to help.Changes or modifi cations not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.IC NoticeThis Class B digital apparatus complies with Canadian ICES-003Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.This device complies with the Industry Canada license exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.Regulatory InformationSetup Operation1 Download Smartphone AppOn the resident’s Smartphone, download and install the“GoControl MyDoorbell” App from the Google Play Store (for Android phones) or from Apple App Store (for iOS phones).2 Create an AccountWith the Smartphone connected to the local network router via WiFi, select “Create an Account.” Enter a name, valid email address, and passwork for the account, then select “Create an Account.”Receive the verifi cation e-mail from mydoorbell@nortek.com with the activation code. NOTE: Check junk/spam email folder. This code expires in one hour after the email is sent. Enter the activation code in the app.3 Connecting to Doorbell CameraThe doorbell camera should be in Discovery mode and the button indicator should fl ash red and green. If the indicator does not fl ash, try pressing the call button for ten to fi fteen seconds to enter Discovery mode.4 Follow Steps on App for Final Setup.Doorbell Camera TroubleshootingPOWERQ: The doorbell cycles off and on?A: Check that the doorbell camera power wires are securely connected. The existing doorbell wiring may be bad. With a chime box installation, you may need to reverse the doorbell wires to the wire connectors. Refer to Step 7.Q: Why doesn’t the doorbell camera power up?A: Refer to installation instructions:1. Confi rm transformer power is turned ON.2. Confi rm diode is installed correctly.3. Confi rm wiring / connections are correct and secure.4. Confi rm transformer power is 15 to 20 VAC.This Nortek Security & Control product is warranted against defects in material and workmanship for twelve (12) months. This warranty extends only to wholesale customers who buy direct from Nortek Security & Control or through Nortek Security & Control’s normal distribution channels. Nortek Security & Control does not warrant this product to consumers. Consumers should inquire from their selling dealer as to the nature of the dealer’s warranty, if any. There are no obligations or liabilities on the part of Nortek Security & Control for consequential damages arising out of or in connection with use or performance of this product or other indirect damages with respect to loss of property, revenue, or profi t, or cost of removal, installation, or reinstallation. All implied warranties, including implied warranties for merchantability and implied warranties for fi tness, are valid only until Warranty Expiration Date as labeled on the product. This Nortek Security & Control LLC Warranty is in lieu of all other warranties express or implied.All products returned for warranty service require a Return Authorization Number (RA#). Contact Nortek Security & Control Returns at 1-855-546-3351 for an RA# and other important details.Product WarrantyCopyright © 2016 Nortek Security & Control 10010716 A8 Indicators StatusTEST Doorbell Camera• TURN power ON.• Press doorbell button.• If chime rings normally, continue tonext step.• If chime DOES NOT ring normally,go to Step 7, reverse wiring. ✔Note: If the doorbell chime does not sound with the doorbell button pressed, it means that the red and black wires need to be reversed.SCREW IN BOTTOM OF DOORBELL CAMERACamera Installation / Security Screw910(OPTIONAL)11AccessoriesMODEL DESCRIPTIONDESCRIPTIONGC-DBC-C1 GoControl wired door chimeGC-DBC-C2 GoControl WiFi door chime 120VAC Plug-INGC-DBC-FP GoControl Doorbell Camera Faceplate Pak: Oil Rubbed, Venetian Bronze, Brass, White,CharcoalIMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. No change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user’s authority to operate the device.

Navigation menu