Teletronics TT900 TT Bridge Router User Manual IP3K Rev TT900

Teletronics International Inc TT Bridge Router IP3K Rev TT900

User Manual

1 TT™900 User Manual 802.11b/g 200mW
2 Table of Contents Disclaimers ………………………….………….….…….……….….………........3 Introduction ……………………………………………………………………….4 Product Features ………………………………………………………………...5 Product Specifications ………………………………………………………….5 Installation ………………………………………………………………..………10 Configuring windows for IP Networking ……………………………………11 Web Configuration Interface ………………………………………………….13 Client Bridge Mode …………………….………….…….………………………13 Access Point Mode …………………………………………………………...…30 Appendix A: Warranty Policy ……………………………………………...…..50 Appendix B: RMA Policy …………………………………………………...…..51 Appendix C: Regulatory Information ……………………………………...…52 Appendix D: Contact Information ………………………………………...…..54 Appendix E: WDS Explained ……………………………………………...…..55 Appendix F: TT900 Upgrade FAQ …….…………………...…...……………..57 Appendix G: Antenna Diversity ……………………………………………....59 Appendix H: Troubleshooting ………………………………………………...60 Appendix I: Key Requirement Chart.…………………..……………………..61 Appendix J: Glossary ……………………………………..……………………62
3Disclaimers No part of this documentation may be reproduced in any form or by any means or used to make any derivative work (such as translation, transformation or adaptation) without written permission from the copyright owner. All other trademarks and registered trademarks are the property of their respective owners. Statement of Conditions We may make improvements or changes in the product described in this documentation at any time. The information regarding the product in this manual is subject to change without notice. We assume no responsibility for errors contained herein or for direct, indirect, special, incidental or consequential damages with the furnishing, performance or use of this manual or equipment supplied with it, even if the suppliers have been advised about the possibility of such damages. Electronic Emission Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference. (2)This device must accept any interference received, including interference that may cause undesired operation. FCC INFORMATION The Federal Communication Commission Radio Frequency Interference Statement includes the following paragraph: The equipment has been tested and found to comply with the limits for a Class B Digital Device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment usage generates radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communication. However, there is no grantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. The equipment is for home or office use. IMPORTANT NOTE FCC RF Radiation Exposure Statement: This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the antenna and your body and must not be co-located or operating in conjunction with any other antenna or transmitter. Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
4Introduction The TT900 is Teletronics’s answer to the ever growing demand for higher bandwidth and security in a wireless network environment. It is based on a brand new redesigned platform that not only offers faster performance and capacity but also supports all current pre IEEE 802.11i wireless security standards. The TT900 is housed in a weather-proof NEMA 4 enclosure, supports high power 802.11 b/g radio, industrial grade construction, multiple antenna options, surge protection on the radio and PoE (Power Over Ethernet) adaptor, and RoHS compliance. TT5800 Product Photos TT900 PCB IEEE 802.11a miniPCI Card TT900 Enclosure (Die Cast Aluminum NEMA 4 Box)
5Product Features • Compact size for small enterprise or system integrate service market • Compliant with IEEE 802.11b/g specifications • Supports 64/128-bit WEP, WPA and IEEE802.1x • Intelligent firmware upgrade via Web browser • Built-in Web-based utility for easy configuration from any Web browser • Support POE (IEEE 802.3af) function • Supports wireless bridging and MAC address filtering • Provide 10/100M, auto sensing MDI/MDI-X Ethernet port • EzManager Support Product Specifications Main Chips • CPU: Ubicom IP3023 • Radio: Supports 802.11b/g Atheros AR5414 Mechanical • Chassis Dimension (W x D x L): 7.5” x 2.75”x 9” Board Specifications Specification Description Network Standard IEEE 802.11 b/g, IEEE 802.3, IEEE802.3x Ethernet 10/100BaseT Ethernet, Auto MDI/MDI-X Network Architecture Infrastructure; Ad-Hoc MAC CSMA/CA Status Indicators POWER, Wireless LAN(RF),Ethernet LAN, Receives Signal Strength(RSS) Push Button Reset to Default Button
6Radio Specifications • IEEE 802.11b/g 2.4 GHz mini-PCI card Specification Description Chipset MAC/BB Processor Atheros AR5414 Power Consumption IEEE 802.11b TX: ~1100 mA RX: ~600 mA IEEE 802.11g TX: ~1100 mA RX: ~600 mA Antenna Connector SMA connector Output Power IEEE 802.11b: • 23dBm (± 1.5dB) @ 1Mbps • 22dBm (± 1.5dB) @ 2Mbps • 21dBm (± 1.5dB) @ 5.5Mbps • 20dBm (± 1.5dB) @ 11Mbps IEEE 802.11g: • 23dBm (±1.5dB) @ 54Mbps • 22dBm (±1.5dB) @ 48Mbps • 21dBm (±1.5dB) @ 36Mbps • 20dBm (±1.5dB) @ 1~24 Mbps Receiver Sensitivity IEEE 802.11b/g Sensitivity @ 8% Packet Error Rate • 54Mbps:-72dBm • 6Mbps:-92dBm Modulation IEEE 802.11b (DSSS) • 5.5/11 Mbps (CCK) • 2 Mbps (DQPSK) • 1 Mbps (DBPSK) IEEE 802.11g (OFDM/DSSS) • 48/54 Mbps (QAM-64) • 24/36 Mbps (QAM-16) • 12/18 Mbps (QPSK) • 6/9 Mbps (BPSK) • 5.5/11Mbps (CCK) • 2Mbps (DQPSK) • 1Mbps (DBPSK) Operating Frequency • USA(FCC): 902 MHz ~ 928 MHz
7 LED Definition (Optional) Item Specification ON (Red) Power on Power Off No power On (Yellow) Connected Off Not connected RF(WLAN) Blinking(Green) Connected and transmitting On (Green) Connected Off Not connected LAN Blinking(Green) Connected and transmitting Blinking left to right Not connected (Scanning for AP) Received Signal Strength Indicator (RSSI) On Connected, indicating Received Signal Strength. Software Specification Item Specification Bridge Features • Universal Bridging • MAC Address Cloning • RTS Threshold/Fragmentation Threshold • Infrastructure or Ad-Hoc Mode • Non-IP Traffic Bridging Security Features • 64-Bit/128-Bit WEP Encryption • WPA Personal Using TKIP or AES • WPA Enterprise Using TKIP or AES • 802.1x Authenticator • Cisco LEAP Support • MAC Address Filter Management Features • Web Access (Username/Password Protected) • Static IP • Automatic Device Discovery & Configuration • SNMP v1, DHCP and PPPoE (Ethernet or Wireless) • Firmware Upgrade via Web Browser • Transmit Power Adjustment External AC Power Adapter Item Specification Input Voltage 110-240VAC Line Frequency 50/60Hz Power Output to M/B 48VDC, 1A
8Environmental Item Specification Operating Temperature -20 C to 70 C (-4 F to 158 F), 10 to 90% (non-condensing) Storage Temperature -25 C to 80 C (-13 F to 176 F), 10 to 90% (non-condensing) Standards / Regulatory Compliance • CE, FCC Product Kit Part Listing 1. TT900 802.11b/g PCBA (1) 2. IEEE 802.11b/g mini-PCI radio card (1) 3. Power over Ethernet Injector (1) 4. 48VDC Power Adapter (1) 5. Ethernet Cable (2) 6. Waterproof RJ-45 Connector (1) 7. Mounting Hardware (1) 8. User Manual Note: If any item listed above is damaged or missing, please contact your dealer immediately. System Requirements • Any desktop or laptop with an Ethernet interface • TCP/IP protocol suite installed • Standard CAT5 Ethernet cables with RJ45 connectors • Internet Explorer 5.0 or later / Firefox 1.0 or higher Note:Professional must install this device.End-user cannot set the functionality by hardware or software from one to another directly.End-user can adjust output power through a drop down menu, but cannot adjust the output power over the applicati on.The EUT will be settled output power not greater than the application by Manufacturer.Installation of this device should be accomplished only by a qualified wireless LAN system installer who is:• Knowledgeable of the use. Installation and configuration procedures and associated networking components.• Knowledgeable of each system component’s equipment User and Installation Guide.• Knowledgeable of the installation procedures, safety, and code requirements for the site’s antenna, antenna mast, antenna cabling, and installation. TELETRONICS highly recommends that the antenna installation be performed by a qualified antenna installation professional.The intended use is generally not for the general public. It is generally for industry/commercial use.The device cannot be sold retail, to the general public or by mall order. It must be sold to dealers or have strict marketing control.The intended use is generally not for the general public. It is generally for industry/commercial use.

Navigation menu