Telit Communications S p A LM940 LM940 User Manual User Guide
Telit Communications S.p.A. LM940 User Guide
User Guide
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 3476656 |
| Application ID | VLo+LkvWiVDL7tuQUfAvtg== |
| Document Description | User Guide |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 132.43kB (1655433 bits) |
| Date Submitted | 2017-07-21 00:00:00 |
| Date Available | 2018-01-20 00:00:00 |
| Creation Date | 2017-07-20 18:12:26 |
| Producing Software | Acrobat Distiller 10.1.16 (Windows) |
| Document Lastmod | 2017-07-20 17:52:53 |
| Document Title | Microsoft Word - 1VV0301352_LM940_HW_User_Guide_R02_20JULY2017 |
| Document Creator | PScript5.dll Version 5.2.2 |
| Document Author: | DWKu |
LM940 HW Design Guide [01.2017] 1VV0301352 Rev. 2 –2017-07-19 Mod.0818 2017-01 Rev.0 LM940 HW Design Guide SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE NOTICE While reasonable efforts have been made to assure the accuracy of this document, Telit assumes no liability resulting from any inaccuracies or omissions in this document, or from use of the information obtained herein. The information in this document has been carefully checked and is believed to be reliable. However, no responsibility is assumed for inaccuracies or omissions. Telit reserves the right to make changes to any products described herein and reserves the right to revise this document and to make changes from time to time in content hereof with no obligation to notify any person of revisions or changes. Telit does not assume any liability arising out of the application or use of any product, software, or circuit described herein; neither does it convey license under its patent rights or the rights of others. It is possible that this publication may contain references to, or information about Telit products (machines and programs), programming, or services that are not announced in your country. Such references or information must not be construed to mean that Telit intends to announce such Telit products, programming, or services in your country. COPYRIGHTS This instruction manual and the Telit products described in this instruction manual may be, include or describe copyrighted Telit material, such as computer programs stored in semiconductor memories or other media. Laws in the Italy and other countries preserve for Telit and its licensors certain exclusive rights for copyrighted material, including the exclusive right to copy, reproduce in any form, distribute and make derivative works of the copyrighted material. Accordingly, any copyrighted material of Telit and its licensors contained herein or in the Telit products described in this instruction manual may not be copied, reproduced, distributed, merged or modified in any manner without the express written permission of Telit. Furthermore, the purchase of Telit products shall not be deemed to grant either directly or by implication, estoppel, or otherwise, any license under the copyrights, patents or patent applications of Telit, as arises by operation of law in the sale of a product. COMPUTER SOFTWARE COPYRIGHTS The Telit and 3rd Party supplied Software (SW) products described in this instruction manual may include copyrighted Telit and other 3rd Party supplied computer programs stored in semiconductor memories or other media. Laws in the Italy and other countries preserve for Telit and other 3rd Party supplied SW certain exclusive rights for copyrighted computer programs, including the exclusive right to copy or reproduce in any form the copyrighted computer program. Accordingly, any copyrighted Telit or other 3rd Party supplied SW computer programs contained in the Telit products described in this instruction manual may not be copied (reverse engineered) or reproduced in any manner without the express written permission of Telit or the 3rd Party SW supplier. Furthermore, the purchase of Telit products shall not be deemed to grant either directly or by implication, estoppel, or otherwise, any license under the copyrights, patents or patent applications of Telit or other 3rd Party supplied SW, except for the normal non-exclusive, royalty free license to use that arises by operation of law in the sale of a product. 1VV0301352 Rev. 2 Page 2 of 68 2017-07-19 LM940 HW Design Guide USAGE AND DISCLOSURE RESTRICTIONS I. License Agreements The software described in this document is the property of Telit and its licensors. It is furnished by express license agreement only and may be used only in accordance with the terms of such an agreement. II. Copyrighted Materials Software and documentation are copyrighted materials. Making unauthorized copies is prohibited by law. No part of the software or documentation may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, without prior written permission of Telit III. High Risk Materials Components, units, or third-party products used in the product described herein are NOT fault-tolerant and are NOT designed, manufactured, or intended for use as on-line control equipment in the following hazardous environments requiring fail-safe controls: the operation of Nuclear Facilities, Aircraft Navigation or Aircraft Communication Systems, Air Traffic Control, Life Support, or Weapons Systems (High Risk Activities"). Telit and its supplier(s) specifically disclaim any expressed or implied warranty of fitness for such High Risk Activities. IV. Trademarks TELIT and the Stylized T Logo are registered in Trademark Office. All other product or service names are the property of their respective owners. V. Third Party Rights The software may include Third Party Right software. In this case you agree to comply with all terms and conditions imposed on you in respect of such separate software. In addition to Third Party Terms, the disclaimer of warranty and limitation of liability provisions in this License shall apply to the Third Party Right software. TELIT HEREBY DISCLAIMS ANY AND ALL WARRANTIES EXPRESS OR IMPLIED FROM ANY THIRD PARTIES REGARDING ANY SEPARATE FILES, ANY THIRD PARTY MATERIALS INCLUDED IN THE SOFTWARE, ANY THIRD PARTY MATERIALS FROM WHICH THE SOFTWARE IS DERIVED (COLLECTIVELY “OTHER CODE”), AND THE USE OF ANY OR ALL THE OTHER CODE IN CONNECTION WITH THE SOFTWARE, INCLUDING (WITHOUT LIMITATION) ANY WARRANTIES OF SATISFACTORY QUALITY OR FITNESS FOR A PARTICULAR PURPOSE. NO THIRD PARTY LICENSORS OF OTHER CODE SHALL HAVE ANY LIABILITY FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING WITHOUT LIMITATION LOST PROFITS), HOWEVER CAUSED AND WHETHER MADE UNDER CONTRACT, TORT OR OTHER LEGAL THEORY, ARISING IN ANY WAY OUT OF THE USE OR DISTRIBUTION OF THE OTHER CODE OR THE EXERCISE OF ANY RIGHTS GRANTED UNDER EITHER OR BOTH THIS LICENSE AND THE LEGAL TERMS APPLICABLE TO ANY SEPARATE FILES, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. 1VV0301352 Rev. 2 Page 3 of 68 2017-07-19 LM940 HW Design Guide Applicability Table PRODUCTS LM940 1VV0301352 Rev. 2 Page 4 of 68 2017-07-19 LM940 HW Design Guide Contents NOTICE COPYRIGHTS .................................................................................................. 2 COMPUTER SOFTWARE COPYRIGHTS ....................................................... 2 USAGE AND DISCLOSURE RESTRICTIONS ................................................ 3 APPLICABILITY TABLE .................................................................................. 4 CONTENTS ...................................................................................................... 5 1. INTRODUCTION ............................................................................ 9 Scope ............................................................................................. 9 Audience ........................................................................................ 9 Contact Information, Support ......................................................... 9 Text Conventions ......................................................................... 11 Related Documents ...................................................................... 12 2. GENERAL PRODUCT DESCRIPTION........................................ 13 Overview ...................................................................................... 13 Product Variants and Frequency Bands ....................................... 13 2.2.1. RF Bands per Regional Variant .................................................... 13 Target market ............................................................................... 14 Main features ................................................................................ 14 Block Diagram .............................................................................. 16 TX Output Power .......................................................................... 17 RX Sensitivity ............................................................................... 17 Mechanical specifications ............................................................. 18 2.8.1. Dimensions ................................................................................... 18 2.8.2. Weight .......................................................................................... 18 Environmental Requirements ....................................................... 18 2.9.1. Temperature Range ..................................................................... 18 2.9.2. RoHS Compliance ........................................................................ 19 3. PINS ALLOCATION .................................................................... 20 Pin-out .......................................................................................... 20 LM940 Signals That Must Be Connected ..................................... 24 Pin Layout .................................................................................... 25 1VV0301352 Rev. 2 Page 5 of 68 2017-07-19 LM940 HW Design Guide 4. POWER SUPPLY ........................................................................ 26 Power Supply Requirements ........................................................ 26 Power Consumption ..................................................................... 26 General Design Rules .................................................................. 27 4.3.1. Electrical Design Guidelines ......................................................... 27 4.3.1.1. + 5V Input Source Power Supply – Design Guidelines ................ 27 4.3.2. Thermal Design Guidelines .......................................................... 27 4.3.3. Power Supply PCB layout Guidelines .......................................... 28 RTC .............................................................................................. 29 Reference Voltage ........................................................................ 29 Internal LDO for GNSS bias ......................................................... 30 5. ELECTRICAL SPECIFICATIONS................................................ 31 Absolute Maximum Ratings – Not Operational............................. 31 Recommended Operating Conditions .......................................... 31 6. DIGITAL SECTION ...................................................................... 32 Logic Levels ................................................................................. 32 6.1.1. 1.8V Pins – Absolute Maximum Ratings ...................................... 32 6.1.2. 1.8V Standard GPIOs ................................................................... 32 6.1.3. 1.8V SIM Card Pins ...................................................................... 33 6.1.4. 2.85V Pins – Absolute Maximum Ratings .................................... 33 6.1.5. SIM Card Pins @2.85V ................................................................ 33 Power On ..................................................................................... 34 6.2.1. Initialization and Activation State .................................................. 34 Power Off ..................................................................................... 35 Unconditional Hardware Reset ..................................................... 36 Communication ports ................................................................... 37 6.5.1. USB Interface ............................................................................... 37 6.5.2. SIM Interface ................................................................................ 39 6.5.2.1. SIM Schematic Example .............................................................. 40 6.5.3. Control Signals ............................................................................. 41 6.5.3.1. W_DISABLE_N ............................................................................ 41 6.5.3.2. WAKE_N ...................................................................................... 41 6.5.3.3. WAN_LED_N ............................................................................... 42 6.5.4. General Purpose I/O .................................................................... 42 6.5.4.1. Using a GPIO Pin as Input ........................................................... 43 6.5.4.2. Using a GPIO Pin as Output ........................................................ 43 6.5.5. I2C – Inter-integrated circuit ......................................................... 43 1VV0301352 Rev. 2 Page 6 of 68 2017-07-19 LM940 HW Design Guide Using the Temperature Monitor Function ..................................... 44 7. RF SECTION ................................................................................ 45 Antenna requirements .................................................................. 45 Main Antenna Requirements ........................................................ 45 Antenna Diversity Requirements .................................................. 45 GNSS Receiver ............................................................................ 46 7.4.1. GNSS RF Front End Design......................................................... 46 Antenna connection ...................................................................... 47 7.5.1. Antenna Connector ...................................................................... 47 7.5.2. Antenna Cable .............................................................................. 48 7.5.3. Antenna Installation Guidelines .................................................... 48 8. AUDIO SECTION ......................................................................... 50 Audio Interface ............................................................................. 50 Digital Audio ................................................................................. 50 9. MECHANICAL DESIGN............................................................... 51 General ......................................................................................... 51 Finishing & Dimensions ................................................................ 51 Drawing ........................................................................................ 51 10. APPLICATION GUIDE ................................................................. 52 Debug of the LM940 Module in Production .................................. 52 Bypass Capacitor on Power Supplies .......................................... 52 EMC Recommendations .............................................................. 53 11. PACKAGING ............................................................................... 56 Tray .............................................................................................. 56 12. CONFORMITY ASSESSMENT ISSUES ..................................... 58 Approvals ..................................................................................... 58 Declaration of Conformity ............................................................. 58 FCC certificates ............................................................................ 58 IC certificates ................................................................................ 58 FCC/IC Regulatory notices ........................................................... 58 13. SAFETY RECOMMENDATIONS ................................................. 62 READ CAREFULLY ..................................................................... 62 14. REFERENCE TABLE OF RF BANDS CHARACTERISTICS ..... 63 15. ACRONYMS ................................................................................ 65 1VV0301352 Rev. 2 Page 7 of 68 2017-07-19 LM940 HW Design Guide 16. DOCUMENT HISTORY ................................................................ 67 1VV0301352 Rev. 2 Page 8 of 68 2017-07-19 LM940 HW Design Guide 1. INTRODUCTION Scope This document introduces the Telit LM940 module and presents possible and recommended hardware solutions for developing a product based on the LM940 module. All the features and solutions detailed in this document are applicable to all LM940 variants, where “LM940” refers to the variants listed in the Applicability Table. If a specific feature is applicable to a specific product only, it will be clearly marked. Information – LM940 refers to all modules listed in the Applicability Table. This document takes into account all the basic functions of a wireless module; a valid hardware solution is suggested for each function, and incorrect solutions and common errors to be avoided are pointed out. Obviously, this document cannot embrace every hardware solution or every product that can be designed. Where the suggested hardware configurations need not be considered mandatory, the information given should be used as a guide and a starting point for properly developing your product with the Telit LM940 module. Information – The integration of the WCDMA/HSPA+/LTE LM940 cellular module within a user application must be done according to the design rules described in this manual. Audience This document is intended for Telit customers, especially system integrators, about to implement their applications using the Telit LM940 module. Contact Information, Support For general contact, technical support services, technical questions and report documentation errors contact Telit Technical Support at: TS-EMEA@telit.com TS-AMERICAS@telit.com TS-APAC@telit.com TS-SRD@telit.com 1VV0301352 Rev. 2 Page 9 of 68 2017-07-19 LM940 HW Design Guide Alternatively, use: http://www.telit.com/en/products/technical-support-center/contact.php For detailed information about where you can buy the Telit modules or for recommendations on accessories and components visit: http://www.telit.com To register for product news and announcements or for product questions contact Telit’s Technical Support Center (TTSC). Our aim is to make this guide as helpful as possible. Keep us informed of your comments and suggestions for improvements. Telit appreciates feedback from the users of our information. 1VV0301352 Rev. 2 Page 10 of 68 2017-07-19 LM940 HW Design Guide Text Conventions Danger – This information MUST be followed or catastrophic equipment failure or bodily injury may occur. Caution or Warning – Alerts the user to important points about integrating the module, if these points are not followed, the module and end user equipment may fail or malfunction. Tip or Information – Provides advice and suggestions that may be useful when integrating the module. All dates are in ISO 8601 format, i.e. YYYY-MM-DD. 1VV0301352 Rev. 2 Page 11 of 68 2017-07-19 LM940 HW Design Guide Related Documents LM940 SW User Guide, 1VV0301343 LM940 AT Commands Reference Guide, 80545ST10791A Generic EVB HW User Guide, 1VV0301249 LM940 Interface Board HW User Guide, 1VV0301384 SIM Integration Design Guide Application Note Rev10, 80000NT10001A Antenna Detection Application Note, 80000NT10002A 1VV0301352 Rev. 2 Page 12 of 68 2017-07-19 LM940 HW Design Guide 2. GENERAL PRODUCT DESCRIPTION Overview The aim of this document is to present possible and recommended hardware solutions useful for developing a product with the Telit LM940 Mini PCIe module. LM940 is Telit’s platform for Mini PCIe module for applications, such as M2M applications, industrial mobile router and table PC, based on the following technologies: LTE / WCDMA networks for data communication Designed for industrial grade quality In its most basic use case, LM940 can be applied as a wireless communication front-end for mobile router products, offering mobile communication features to an external host CPU through its rich interfaces. LM940 can further support customer software applications and security features. LM940 provides a software application development environment with sufficient system resources for creating rich on-board applications. Thanks to a dedicated application processor and embedded security resources, product developers and manufacturers can create products that guarantee fraud prevention and tamper evidence without extra effort for additional security precautions. LM940 is available in hardware variants as listed in Applicability Table The designated RF band sets per each variant are detailed in Section 2.2, Product Variants and Frequency Bands. Product Variants and Frequency Bands The operating frequencies in LTE & WCDMA modes conform to the 3GPP specifications. 2.2.1. RF Bands per Regional Variant This table summarizes the LM940, showing the supported band sets and the supported band pairs and triple for carrier aggregation. RF Bands and Carrier Aggregation LTE FDD Bands 1, 2, 3, 4, 5, 7, 8, 12, 13, 17, 20, 25, 26, 28, 29, 30, 66 GNSS GPS, GLONASS, BeiDou, Galileo LTE TDD HSPA+ 38, 40, 41 1, 2, 4, 5, 8 LTE 2DL carrier aggregation combinations North America B2+B2, B2+B4, B2+B5, B2+B12, B2+B13, B2+B17, B2+B29, B2+B30, B4+B4, B4+B5, B4+B7, B4+B12, B4+B13, B4+B17, B4+B29, B4+B30, B5+B30, B12+B12, B12+B30, B25+B25, B25+B26, B25+B41, B26+B41, B29+B30, B41+B41 Europe B1+B20, B3+B3, B3+B7, B3+B20, B3+B38, B7+B7, B7+B8, B7+B20, B38+B38 1VV0301352 Rev. 2 Page 13 of 68 2017-07-19 LM940 HW Design Guide Australia B1+B3, B1+B7, B1+B28, B3+B8, B3+B28, B5+B7, B5+B40, B7+B8, B7+B20 LTE 3DL carrier aggregation combinations North America B2+B2+B12/17, B2+B2+B13, B2+B2+B4, B2+B4+B5, B2+B4+B12, B2+B4+B13, B2+B4+B29, B2+B5+B30, B2+B12+B12, B2+B12+B30, B2+B29+B30, B4+B4+B5, B4+B4+B7, B4+B4+B12, B4+B4+B13, B4+B5+B30, B4+B12+B12, B4+B12+B30, B4+B29+B30, B25+B26+B41, B25+B41+B41, B26+B41+B41, B41+B41+B41 Europe B1+B3+B20, B1+B7+B20, B3+B3+B7, B3+B3+B20, B3+B7+B20, B3+B7+B7, B3+B20+B38, B3+B38+B38 Australia B3+B3+B5, B3+B3+B8, B3+B7+B7, B3+B7+B28, B7+B7+B28, B28+B40+B40, B40+B40+B40 Refer to Chapter 13 for details information about frequencies and bands. Target market LM940 can be used for telematics applications where tamper-resistance, confidentiality, integrity, and authenticity of end-user information are required, for example: Mobile router Industrial equipment Home network Internet connectivity Main features The LM940 family of industrial grade cellular modules features LTE and multi-RAT module together with an on-chip powerful application processor and a rich set of interfaces. The major functions and features are listed below. Main Features Function Features Module Audio subsystem 1VV0301352 Rev. 2 Multi-RAT cellular module for data communication LTE FDD/TDD Cat11(600/75 Mbps DL/UL) WCDMA up to DC HSPA+, Rel.9 Support for GPS, GLONASS, BeiDou, Galileo Support digital audio interface (optional) Page 14 of 68 2017-07-19 LM940 HW Design Guide Function Features Two USIM ports – dual voltage Support for dual SIM Class B and Class C support Clock rates up to 4 MHz Application processor Interfaces Application processor to run customer application code 32 bit ARM Cortex-A7 up to 1.19 GHz running the Linux operating system 4Gbit NAND Flash + 2Gbit LPDDR2 MCP is supported to allow for customer’s own software applications Rich set of interfaces, including: Major software features Form factor 1VV0301352 Rev. 2 USB2.0 / USB3.0 – USB port is typically used for: Flashing of firmware and module configuration Production testing Accessing the Application Processor’s file system AT command access High-speed WWAN access to external host Diagnostic monitoring and debugging Communication between Java application environment and an external host CPU NMEA data to an external host CPU Peripheral Ports – GPIOs Advanced security features Boot integrity of firmware up to customer applications Disable/secure re-enable of debug Embedded security FOTA (optional) Telit Unified AT command set Mini PCIe Form factor (50.95x30x2.7mm), accommodating the multiple RF bands Page 15 of 68 2017-07-19 LM940 HW Design Guide Function Features Environment and quality requirements The entire module is designed and qualified by Telit for satisfying the environment and quality requirements for use in applications1. Single supply module The module generates all its internal supply voltages. RTC The real-time clock is supported. Operating temperature Range -40 °C to +85 °C (conditions as defined in Section 2.9.1, Temperature Range) Block Diagram Below figure shows an overview of the internal architecture of the LM940 module. LM940 Block Diagram It includes the following sub-functions: Application processor, Module subsystem and Location processing with their external interfaces. These three functions are contained in a single SOC. RF front end In accordance with Telit’s Robustness Validation, using AEC‐Q100‐defined qualification tests 1VV0301352 Rev. 2 Page 16 of 68 2017-07-19 LM940 HW Design Guide Rich IO interfaces. Depending on which LM940 software features are enabled, some of its interfaces that are exported through multiplexing may be used internally and thus may not be usable by the application. PMIC with the RTC function inside TX Output Power Band Power class 3G WCDMA Class 3 (0.2W) LTE All Bands Class 3 (0.2W) RX Sensitivity Below the 3GPP measurement conditions used to define the RX sensitivity: Technology 3GPP Compliance 4G LTE Throughput >95% 10MHz Dual Receiver 3G WCDMA BER <0.1% 12.2 Kbps Dual Receiver Product Band Typical Rx Sensitivity (dBm) * / ** (LTE BW = 10 MHz) LM940 1VV0301352 Rev. 2 LTE FDD B1 -101.5 LTE FDD B2 -101.0 LTE FDD B3 -101.5 LTE FDD B4 -101.0 LTE FDD B5 -102.5 LTE FDD B7 -99.5 LTE FDD B8 -102.5 LTE FDD B12 -102.0 LTE FDD B13 -102.0 LTE FDD B17 -102.0 LTE FDD B20 -102.0 Page 17 of 68 2017-07-19 LM940 HW Design Guide LM940 LTE FDD B25 -101.0 LTE FDD B26 -102.0 LTE FDD B28 -102.0 LTE FDD B30 -100.5 LTE FDD B66 -101.0 LTE TDD B38 -100.0 LTE TDD B40 -100.0 LTE TDD B41 -99.5 WCDMA FDD B1 -108.5 WCDMA FDD B2 -108.5 WCDMA FDD B4 -108.5 WCDMA FDD B5 -109.5 WCDMA FDD B8 -109.5 * LTE Rx Sensitivity shall be verified by using both (all) antenna ports simultaneously. ** 3.3 Voltage / Room temperature Mechanical specifications 2.8.1. Dimensions The LM940 module’s overall dimensions are: Length: 50.95 mm, +/- 0.15 mm tolerance Width: 30.00 mm, +/- 0.15 mm tolerance Thickness: 2.70 mm, +/- 0.15 mm tolerance 2.8.2. Weight The nominal weight of the LM940 module is 9.6 gram. Environmental Requirements 2.9.1. Temperature Range Note Operating Temperature Range 1VV0301352 Rev. 2 –20°C ~ +55°C This range is defined by 3GPP (the global standard for wireless mobile communication). Telit guarantees its modules to comply with all the 3GPP requirements and to have full functionality of the module with in this range. Page 18 of 68 2017-07-19 LM940 HW Design Guide Note –40°C ~ +85°C Telit guarantees full functionality within this range as well. However, there may possibly be some performance deviations in this extended range relative to 3GPP requirements, which means that some RF parameters may deviate from the 3GPP specification in the order of a few dB. For example: receiver sensitivity or maximum output power may be slightly degraded. Even so, all the functionalities, such as call connection, SMS, USB communication, UART activation etc., will be maintained, and the effect of such degradations will not lead to malfunction. Storage and nonoperating Temperature Range 2.9.2. –40°C ~ +85°C RoHS Compliance As a part of the Telit corporate policy of environmental protection, the LM940 complies with the RoHS (Restriction of Hazardous Substances) directive of the European Union (EU directive 2011/65/EU). 1VV0301352 Rev. 2 Page 19 of 68 2017-07-19 LM940 HW Design Guide 3. PINS ALLOCATION Pin-out LM940 Pin-out Pin Signal I/O Function Type Comment USB HS 2.0 Communication Port 38 USB_D+ I/O USB 2.0 Data Plus Analog 36 USB_D- I/O USB 2.0 Data Minus Analog USB SS 3.0 Communication Port 25 USB_SS_TX_P USB 3.0 superspeed transmit – plus Analog 23 USB_SS_TX_M USB 3.0 superspeed transmit – minus Analog 33 USB_SS_RX_P USB 3.0 superspeed receive – plus Analog 31 USB_SS_RX_M USB 3.0 superspeed receive – minus Analog SIM Card Interface 1 SIMVCC1 Supply output for an external UIM1 card 1.8V / 2.85V 10 SIMIO1 I/O Data connection with an external UIM1 card 1.8V / 2.85V 12 SIMCLK1 Clock output to an external UIM1 card 1.8V / 2.85V 14 SIMRST1 Reset output to an external UIM1 card 1.8V / 2.85V 1VV0301352 Rev. 2 Page 20 of 68 Power 2017-07-19 LM940 HW Design Guide SIM Card Interface 2 13 SIMVCC2 Supply output for an external UIM2 card 1.8 / 2.85V 19 SIMIO2 I/O Data connection with an external UIM2 card 1.8 / 2.85V 17 SIMCLK2 Clock output to an external UIM2 card 1.8 / 2.85V SIMRST2 Reset output to an external UIM2 card 1.8 / 2.85V Power Digital I/O (GPIOs) GPIO_01 I/O General purpose I/O, SIMIN1 depending on product 1.8V GPIO_02 I/O General purpose I/O, SIMIN2 depending on product 1.8V 44 GPIO_03 I/O General purpose I/O 1.8V 46 GPIO_04 I/O General purpose I/O 1.8V Control Signal WAKE_N Host wake-up 1.8V 20 W_DISABLE_N RF disable 1.8V 42 WAN_LED_N LED control 1.8V Reference Voltage 1.8V Miscellaneous Functions 11 VREG_L6_1P8 1VV0301352 Rev. 2 Page 21 of 68 Power 2017-07-19 LM940 HW Design Guide 22 SYSTEM_RESET_N Reset Input 1.8V Digital Audio Interface 45 DVI _CLK PCM Clock 1.8V 47 DVI _TX PCM Data Out 1.8V 49 DVI _RX PCM Data In 1.8V 51 DVI _WAO PCM Frame Sync 1.8V 30 I2C_SCL I2C Clock 1.8V 32 I2C_SDA I/O I2C Data 1.8V I2C Interface Power Supply VBATT Power supply Power 24 VBATT Power supply Power 39 VBATT Power supply Power 41 VBATT Power supply Power 52 VBATT Power supply Power GND Ground Ground GND Ground Ground 15 GND Ground Ground 18 GND Ground Ground GROUND 1VV0301352 Rev. 2 Page 22 of 68 2017-07-19 LM940 HW Design Guide 21 GND Ground Ground 26 GND Ground Ground 27 GND Ground Ground 29 GND Ground Ground 34 GND Ground Ground 35 GND Ground Ground 37 GND Ground Ground 40 GND Ground Ground 43 GND Ground Ground 50 GND Ground Ground Reserved Reserved (NC) 16 Reserved Reserved (NC) 28 Reserved Reserved (NC) 48 Reserved Reserved (NC) Reserved Information – If the DVI and I2C interface are not used, the signals can be left floating. 1VV0301352 Rev. 2 Page 23 of 68 2017-07-19 LM940 HW Design Guide Information – Unless otherwise specified, RESERVED pins must be left unconnected (Floating). LM940 Signals That Must Be Connected Below table specifies the LM940 signals that must be connected for a debugging purpose even if not used by the end application: Mandatory Signals Pin Signal Notes 2, 24, 39, 41, 52 VBATT 4, 9, 15, 18, 21, 26, 27, 29, 34, 35, 37, 40, 43, 50 GND 38 USB_D+ If not used, connect to a test point or an USB connector 36 USB_D- If not used, connect to a test point or an USB connector 1VV0301352 Rev. 2 Page 24 of 68 2017-07-19 LM940 HW Design Guide Pin Layout 1VV0301352 Rev. 2 Page 25 of 68 2017-07-19 LM940 HW Design Guide 4. POWER SUPPLY The power supply circuitry and board layout are very important parts of the full product design, with critical impact on the overall product performance. Read the following requirements and guidelines carefully to ensure a good and proper design. Power Supply Requirements The LM940 power requirements are as follows: Power Supply Requirements Nominal supply voltage 3.3V Supply voltage range 3.10V – 3.6V Maximum ripple on module input supply 30 mV Power Consumption Below table provides typical current consumption values of LM940 for various operation modes. LM940 Current Consumption Mode Average [Typ.] Mode Description IDLE Mode IDLE Mode 60.0 mA No call connection USB3.0 is connected to a host Operative Mode (LTE) LTE (22 dBm) 750 mA LTE data call (Non-CA BW 5MHz, RB=1) 1250 mA LTE data call (CA_3A+7A+20A, 20MHz+20MHz+20MHz, Full RB, 256QAM DL / 64QAM UL, FDD 600Mbps DL / 75Mbps UL) Operative Mode (WCDMA) WCDMA Voice 650 mA WCDMA voice call (Tx = 23 dBm) WCDMA HSPA (22 dBm) 650 mA WCDMA data call (DC-HSDPA up to 42 Mbps, Max Throughput) * Worst/best case current values depend on network configuration - not under module control. ** Applied MPR –2dB 16-QAM full RB *** 3.3 voltage / room temperature 1VV0301352 Rev. 2 Page 26 of 68 2017-07-19 LM940 HW Design Guide Information – The electrical design for the power supply must ensure a peak current output of at least 2A. General Design Rules The principal guidelines for the Power Supply Design embrace three different design steps: Electrical design Thermal design PCB layout 4.3.1. Electrical Design Guidelines The electrical design of the power supply depends strongly on the power source where this power is drained. 4.3.1.1. + 5V Input Source Power Supply – Design Guidelines The desired output for the power supply is 3.8V. So, the difference between the input source and the desired output is not big, and therefore a linear regulator can be used. A switching power supply is preferred to reduce power consumption. When using a linear regulator, a proper heat sink must be provided to dissipate the power generated. A bypass low ESR capacitor of adequate capacity must be provided to cut the current absorption peaks close to the LE925A4 module. A 100 μF tantalum capacitor is usually suitable (on both VPH_PWR and VPH_PWR_RF together). Make sure that the low ESR capacitor on the power supply output (usually a tantalum one) is rated at least 10V. A protection diode must be inserted close to the power input to protect the LE925A4 module from power polarity inversion. Figure shows an example of linear regulator with 5V input. 4.3.2. Thermal Design Guidelines The thermal design for the power supply heat sink must be done with the following specifications: 1VV0301352 Rev. 2 Page 27 of 68 2017-07-19 LM940 HW Design Guide Average current consumption during RF transmission @PWR level max in LM940 as shown in Section 4.2, Power Consumption table. Information – The average consumption during transmission depends on the power level at which the device is requested to transmit via the network. Therefore, the average current consumption varies significantly. Information – The thermal design for the power supply must be made keeping an average consumption at the maximum transmitting level during calls of LTE/HSPA. Considering the very low current during Idle, especially if the Power Saving function is enabled, it is possible to consider from the thermal point of view that the device absorbs significant current only during Data session. In LTE/WCDMA/HSPA mode, the LM940 emits RF signals continuously during transmission. Therefore, you must pay special attention how to dissipate the heat generated. While designing the application board, the designer must make sure that the LM940 module is located on a large ground area of the application board for effective heat dissipation. Information – The LM940 must be connected to the ground and metal chassis of the host board for best RF performance and thermal dispersion as well as to have module fixed. 4.3.3. The two holes at the top of the module and the main ground of the host board must be fastened together. The shield cover of the module and the main board of the host board or the metal chassis of the host device should be connected with conductive materials. Power Supply PCB layout Guidelines As seen in the electrical design guidelines, the power supply must have a low ESR capacitor on the output to cut the current peaks and a protection diode on the input to protect the supply from spikes and polarity inversion. The placement of these components 1VV0301352 Rev. 2 Page 28 of 68 2017-07-19 LM940 HW Design Guide is crucial for the correct operation of the circuitry. A misplaced component can be useless or can even decrease the power supply performances. The bypass low ESR capacitor must be placed close to the LM940 power input pins, or if the power supply is of a switching type, it can be placed close to the inductor to cut the ripple, as long as the PCB trace from the capacitor to LM940 is wide enough to ensure a drop-less connection even during the 2A current peaks. The protection diode must be placed close to the input connector where the power source is drained. The PCB traces from the input connector to the power regulator IC must be wide enough to ensure that no voltage drops occur during the 2A current peaks. The PCB traces to LM940 and the bypass capacitor must be wide enough to ensure that no significant voltage drops occur when the 2A current peaks are absorbed. This is needed for the same above-mentioned reasons. Try to keep these traces as short as possible. The PCB traces connecting the switching output to the inductor and the switching diode must be kept as short as possible by placing the inductor and the diode very close to the power switching IC (only for the switching power supply). This is done to reduce the radiated field (noise) at the switching frequency (usually 100500 kHz). Use a good common ground plane. Place the power supply on the board in a way to guarantee that the high current return paths in the ground plane do not overlap any noise sensitive circuitry, such as the microphone amplifier/buffer or earphone amplifier. The power supply input cables must be kept separate from noise sensitive lines, such as microphone/earphone cables. RTC The RTC within the LM940 module does not have a dedicated RTC supply pin. The RTC block is supplied by the VBATT supply. If VBATT power is removed, RTC is not maintained so if maintaining an internal RTC is needed, VBATT must be supplied continuously. Reference Voltage 1.8V regulated power supply output is provided as the reference voltage to a host board. This output is active when the module is ON and goes OFF when the module is shut down. This table lists the VREG_L6_IP8 signal of LM940. LM940 Reference Voltage PIN Signal I/O Function Type Comment 11 VREG_L6_1P8 Reference Voltage power 1.8V 1VV0301352 Rev. 2 Page 29 of 68 2017-07-19 LM940 HW Design Guide Internal LDO for GNSS bias The LDO for GNSS bias is applied inside the LM940 model. The voltage supply come from LM940’s LDO to GNSS active antenna. This table lists the LDO for GNSS bias of LM940. LM940 Reference Voltage Symbol Parameter Min Typ Max Unit VGNSS DC bias Voltage of Internal LDO for GNSS bias 2.9 3.1 3.3 [V] IGNSS DC bias Current of Internal LDO for GNSS bias 50 [mA] 1VV0301352 Rev. 2 Page 30 of 68 2017-07-19 LM940 HW Design Guide 5. ELECTRICAL SPECIFICATIONS Absolute Maximum Ratings – Not Operational Caution – A deviation from the value ranges listed below may harm the LM940 module. Absolute Maximum Ratings – Not Operational Symbol VBATT Parameter Battery supply voltage on pin VBATT Min Max Unit -0.5 +4.0 [V] Recommended Operating Conditions Recommended Operating Conditions Symbol Parameter Min Typ Max Unit Tamb Ambient temperature -40 +25 +85 [°C] VBATT Battery supply voltage on pin VBATT 3.1 3.3 3.6 [V] IVBATT + IVBATT_PA Peak current to be used to dimension decoupling capacitors on pin VBATT 80 2500 [mA] 1VV0301352 Rev. 2 Page 31 of 68 2017-07-19 LM940 HW Design Guide 6. DIGITAL SECTION Logic Levels Unless otherwise specified, all the interface circuits of the LM940 are 1.8V CMOS logic. Only USIM interfaces are capable of dual voltage I/O. The following tables show the logic level specifications used in the LM940 interface circuits. The data specified in the tables below is valid throughout all drive strengths and the entire temperature ranges. Caution – Do not connect LM940’s digital logic signal directly to OEM’s digital logic signal with a level higher than 2.3V for 1.8V CMOS signals. 6.1.1. 1.8V Pins – Absolute Maximum Ratings Absolute Maximum Ratings – Not Functional Parameter Min Max Input level on any digital pin when on -- +2.16V Input voltage on analog pins when on -- +2.16 V 6.1.2. 1.8V Standard GPIOs Operating Range – Interface Levels (1.8V CMOS) Parameter Min Max Unit Comment VIH Input high level 1.17V 2.1V [V] VIL Input low level -0.3V 0.63V [V] VOH Output high level 1.35V 1.8V [V] VOL Output low level 0V 0.45V [V] IIL Low-level input leakage current -1 -- [uA] No pull-up IIH High-level input leakage current -- [uA] No pull-down IILPU Low-level input leakage current -97.5 -27.5 [uA] With pull-up 1VV0301352 Rev. 2 Page 32 of 68 2017-07-19 LM940 HW Design Guide Parameter Min Max Unit IIHPD High-level input leakage current 27.5 97.5 [uA] CI/o I/O capacitance -- [pF] 6.1.3. Comment With pull-down 1.8V SIM Card Pins Operating Range – SIM Pins Working at 1.8V Parameter Min Max Unit Comment VIH Input high level 1.26V 2.1V [V] VIL Input low level -0.3V 0.36V [V] VOH Output high level 1.44V 1.8V [V] VOL Output low level 0V 0.4V [V] IIL Low-level input leakage current -- 1000 [uA] No pull-up IIH High-level input leakage current -20 20 [uA] No pull-down Unit Comment 6.1.4. 2.85V Pins – Absolute Maximum Ratings Absolute Maximum Ratings – Not Functional Parameter Min Max Input level on any digital pin when on -- +3.42V Input voltage on analog pins when on -- +3.42 V 6.1.5. SIM Card Pins @2.85V Operating Range – For SIM Pins Operating at 2.85V Parameter Min Max VIH Input high level 1.995V 3.15V [V] VIL Input low level -0.3V 0.57V [V] VOH Output high level 2.28V 2.85V [V] VOL Output low level 0V 0.4V [V] 1VV0301352 Rev. 2 Page 33 of 68 2017-07-19 LM940 HW Design Guide Parameter Min Max Unit Comment IIL Low-level input leakage current -- 1000 [uA] No pull-up IIH High-level input leakage current -20 20 [uA] No pull-down Power On The LM940 is automatically turning on when the VBATT is supplied. Information – To turn on the LM940 module, the W_DISABLE_N pin must not be asserted low. 6.2.1. Initialization and Activation State After turning on the LM940 module, the LM940 is not yet activated because the SW initialization process of the LM940 module is still in process internally. It takes some time to fully complete the HW and SW initialization of the module. For this reason, it is impossible to access LM940 during the Initialization state. As shown in below figure, the LM940 becomes operational (in the Activation state) at least 15 seconds after the VBATT is supplied. LM940 Initialization and Activation VBATT W_DISABLE_N VREG_L6_1P8 TBD sec All Interfaces And Pins Configured TBD sec Internal State 1VV0301352 Rev. 2 OFF State Initialization State Page 34 of 68 USB Driver Loaded Activation State 2017-07-19 LM940 HW Design Guide Information – To check if the LM940 has completely powered on, LM940 and the host must be connected via USB. When USB driver completely loaded, the module has completely powered on and is ready to accept AT commands. Information – During SW initialization of the LM940, the SW configures all pins and interfaces to their desired mode. When VREG_L6_1P8 goes high, this indicates that the initialization of all I/O pins is completed. Information – Active low signals are labeled with a name that ends with “_N” Information – To avoid a back-powering effect, it is recommended to avoid having any HIGH logic level signal applied to the digital pins of the module when it is powered OFF or during an ON/OFF transition. Power Off The LM940 module can be shut down by a software command. When a shutdown command is sent, LM940 goes into the Finalization state and at the end of the finalization process shuts down VREG_L6_1P8. The duration of the finalization state can differ according to the current situation of the module, so a value cannot be defined. Usually, it will take more than 12 seconds from sending a shutdown command until reaching a complete shutdown. The DTE should monitor the status of VREG_L6_1P8 to observe the actual power-off. Information – To completely shut down the LM940 module, the W_DISABLE_N pin must be asserted low. Otherwise, the LM940 will turn on again after shut down. 1VV0301352 Rev. 2 Page 35 of 68 2017-07-19 LM940 HW Design Guide Information – To avoid a back-powering effect, it is recommended to avoid having any HIGH logic level signal applied to the digital pins of the module when it is powered OFF or during an ON/OFF transition. Shutdown by Software Commnad VPH_PWR Must Be Asserted Low. W_DISABLE_N AT#SHDN VREG_L6_1P8 Monitoring Status Variable Above TBD sec Internal State Activation State Finalization State OFF State Unconditional Hardware Reset To unconditionally restart the LM940 module, the SYSTEM_RESET_N pin must be asserted low for a between 100 milliseconds and 150milliseconds then released. Below figure shows a simple circuit for this action. Circuit for Unconditional Hardware Reset SYSTEM_RESET_N 100 ms < Hold Time < 150ms R1 Unconditional Reset Impulse Q1 R2 GND Information – The Unconditional Hardware Reset must be used only as an emergency exit procedure, and not as a normal power-off operation. 1VV0301352 Rev. 2 Page 36 of 68 2017-07-19 LM940 HW Design Guide Information – Do not use any pull-up resistor on the RESET_N line or any totem pole digital output. Using a pull-up resistor may cause latchup problems on the LM940 power regulator and improper functioning of the module. The RESET_N line must be connected only in an opencollector configuration. Communication ports Below table summarizes all the hardware interfaces of the LM940 module. LM940 Hardware Interfaces Interface LM940 USB Super-speed USB3.0 with high-speed USB2.0 USIM x2, dual voltage each (1.8V/2.85V) Control Signals W_DISABLE_N, WAKE_N, WAN_LED_N GPIO X4, GPIO I2C I2C (optional) Audio I/F PCM (optional) Antenna ports 2 for Cellular, 1 for GNSS 6.5.1. USB Interface The LM940 module includes super-speed USB3.0 with high-speed USB2.0 backward compatibility. It is compliant with Universal Serial Bus Specification, Revision 3.0 and can be used for control and data transfers as well as for diagnostic monitoring and firmware update. The USB port is typically the main interface between the LM940 module and OEM hardware. USB 3.0 needs series capacitors on the TX lines in both directions for AC coupling. In order to interface USB3.0 with an application board of customer, 0.1uF capacitors should be installed on USB_SS_RX_P/M lines of the LM940. There are already series capacitors on USB_SS_TX_P/M lines inside LM940 module. The USB interface suggested connection is the following: Connection for USB Interface 1VV0301352 Rev. 2 Page 37 of 68 2017-07-19 LM940 HW Design Guide Information – The USB signal traces must be routed carefully. Minimize trace lengths, number of vias, and capacitive loading. The impedance value should be as close as possible to 90 Ohms differential. Below table lists the USB interface signals. USB Interface Signals PIN Signal I/O Function Type 38 USB_D+ I/O USB 2.0 Data Plus Analog 36 USB_D- I/O USB 2.0 Data Minus Analog 33 USB_SS_RX_P 31 USB_SS_RX_M 25 USB_SS_TX_P 23 USB_SS_TX_M USB 3.0 super-speed receive – plus USB 3.0 super-speed receive – minus USB 3.0 super-speed transmit – plus USB 3.0 super-speed transmit – minus Comment Analog Analog Analog Analog Information – Even if USB communication is not used, it is still highly recommended to place an optional USB connector on the application board. At least test points of the USB signals are required since the USB physical communication is needed in the case of SW update. 1VV0301352 Rev. 2 Page 38 of 68 2017-07-19 LM940 HW Design Guide Information – Consider placing a low-capacitance ESD protection component to protect LM940 against ESD strikes If an ESD protection should be added, the suggested connectivity is as follows: ESD Protection for USB2.0 ESD Protection for USB3.0 6.5.2. SIM Interface The LM940 supports two external SIM interfaces (1.8V or 2.85V). Below table lists the SIM interface signals. SIM Interface Signals PIN Signal I/O Function Type Comment SIM Card Interface 1 1VV0301352 Rev. 2 Page 39 of 68 2017-07-19 LM940 HW Design Guide SIMVCC1 Supply output for an external UIM1 card 1.8V / 2.85V 10 SIMIO1 I/O Data connection with an external UIM1 card 1.8V / 2.85V 12 SIMCLK1 Clock output to an external UIM1 card 1.8V / 2.85V 14 SIMRST1 Reset output to an external UIM1 card 1.8V / 2.85V Power SIM Card Interface 2 13 SIMVCC2 Supply output for an external UIM2 card 1.8 / 2.85V 19 SIMIO2 I/O Data connection with an external UIM2 card 1.8 / 2.85V 17 SIMCLK2 Clock output to an external UIM2 card 1.8 / 2.85V SIMRST2 Reset output to an external UIM2 card 1.8 / 2.85V Power Digital I/O (GPIOs) GPIO_01 UIM1 Card Present Detect 1.8V GPIO_01 can be used as SIMIN1 GPIO_02 UIM2 Card Present Detect 1.8V GPIO_02 can be used as SIMIN2 6.5.2.1. SIM Schematic Example The following Figures illustrate in particular how the application side should be designed. SIM Schematics LM940 SIMIO SIMCLK SIMRST SIMVCC . . . . C3 C2 C7 SIM_CARD C6 C5 4 C1 SIMIN 1VV0301352 Rev. 2 C4 C3 C2 C1 33pF (DNI) 33pF (DNI) 33pF (DNI) 100nF Page 40 of 68 2017-07-19 LM940 HW Design Guide Information – LM940 contains an internal pull-up resistor on SIMIO. It is not necessary to install external pull – up resistor. 6.5.3. Control Signals The LM940 supports the following control signals: W_DISABLE_N WAKE_N WAN_LED_N Below table lists the control signals of LM940. Module Control Signal PIN Signal I/O 20 42 W_DISABLE_N WAKE_N WAN_LED_N 6.5.3.1. Function RF disable (airplane mode) Host wake-up LED control Type Comment 1.8V 1.8V 1.8V W_DISABLE_N The W_DISABLE_N signal is provided to make the LM940 goes into the airplane mode: Enter into the airplane mode: Low Normal operating mode: High or Leave the W_DISABLE_N not connected The W_DISABLE_N should be controlled when the LM940 to either turn on or off. 6.5.3.2. WAKE_N The WAKE_N signal wakes the host when specific events occur. Recommended WAKE_N connection is the following: Recommended WAKE_N connection VCC R1 LM940 Open collector Host Input WAKE_N 1VV0301352 Rev. 2 Page 41 of 68 2017-07-19 LM940 HW Design Guide 6.5.3.3. WAN_LED_N The WAN_LED_N signal drives the LED output. The recommended WAN_LED_N connection is the following: Recommended WAN_LED_N connection 6.5.4. General Purpose I/O The general-purpose I/O pins can be configured to act in three different ways: Input Output Dedicate Function (Customer Requirement) Input pins can only be read and report digital values (high or low) present on the pin at the read time. Output pins can only be written or queried and set the value of the pin output. The following GPIOs are always available as a primary function on the LM940. Below table lists the GPIO signals of LM940. GPIOs Pin no. Signal I/O Function Type Drive Strength GPIO_01 I/O Configurable GPIO CMOS 1.8V 2-16 mA GPIO_02 I/O Configurable GPIO CMOS 1.8V 2-16 mA 44 GPIO_03 I/O Configurable GPIO CMOS 1.8V 2-16 mA 46 GPIO_04 I/O Configurable GPIO CMOS 1.8V 2-16 mA 1VV0301352 Rev. 2 Page 42 of 68 2017-07-19 LM940 HW Design Guide 6.5.4.1. Using a GPIO Pin as Input GPIO pins, when used as inputs, can be tied to a digital output of another device and report its status, provided the device interface levels are compatible with the GPIO 1.8V CMOS levels. If a digital output of a device is tied to GPIO input, the pin has interface levels different than 1.8V CMOS. It can be buffered with an open collector transistor with a 47 kΩ pull-up resistor to 1.8V. 6.5.4.2. Using a GPIO Pin as Output GPIO pins, when used as outputs, can drive 1.8V CMOS digital devices or compatible hardware. When set as outputs, the pins have a push-pull output, and therefore the pullup resistor can be omitted. GPIO Output Pin Equivalent Circuit 6.5.5. I2C – Inter-integrated circuit The LM940 supports an I2C interface on the following pins: Below table lists the I2C signals of LM940. Module I2C Signal PIN 30 32 Signal I2C_SCL I2C_SDA I/O I/O Function I2C Clock I2C Data Type Comment CMOS 1.8V CMOS 1.8V The I2C interface is used for controlling peripherals inside the module (such as codec, etc.). 1VV0301352 Rev. 2 Page 43 of 68 2017-07-19 LM940 HW Design Guide Information – I2C is supported only on from Modem side as SW emulation of I2C on GPIO lines. Please contact us if you use it. Information – If the I2C interface is not used, the signals can be left floating. Using the Temperature Monitor Function The Temperature Monitor permits to monitor the module’s internal temperature and, if properly set (see the #TEMPSENS command in LM940 AT Commands Reference Guide ), raises a GPIO to High Logic level when the maximum temperature is reached. 1VV0301352 Rev. 2 Page 44 of 68 2017-07-19 LM940 HW Design Guide 7. RF SECTION Antenna requirements The antenna connection is one of the most important aspect in the full product design as it strongly affects the product overall performance. Hence read carefully and follow the requirements and the guidelines for a proper design. The LM940 is provided with three RF connectors. The available connectors are: Main RF antenna: TX/RX path Auxiliary RF antenna: Combined Diversity and GNSS GNSS RF antenna: Dedicated GNSS Main Antenna Requirements The antenna for the LM940 device must meet the following requirements: WCDMA / LTE Antenna Requirements Frequency range Depending by frequency band(s) provided by the network operator, the customer shall use the most suitable antenna for that/those band(s) The bands supported by the LM940 is provided in Section 2.2, Product Variants and Frequency Bands. Impedance 50 Ohm Input power > 24 dBm average power in WCDMA & LTE VSWR absolute max <= 10:1 VSWR recommended <= 2:1 Antenna Diversity Requirements This product includes an input for a second Rx antenna to improve radio sensitivity. The function is called Antenna Diversity. Antenna Diversity Requirements Frequency range Depending by frequency band(s) provided by the network operator, the customer shall use the most suitable antenna for that/those band(s) The bands supported by the LM940 is provided in Section 2.2, Product Variants and Frequency Bands. Impedance 50Ω VSWR recommended ≤ 2:1 1VV0301352 Rev. 2 Page 45 of 68 2017-07-19 LM940 HW Design Guide The second Rx antenna should not be located in the close vicinity of main antenna. In order to improve Diversity Gain, Isolation and reduce mutual interaction, the two antennas should be located at the maximum reciprocal distance possible, taking into consideration the available space into the application. For the same reason, the Rx antenna should also be cross-polarized with respect to the main antenna. Isolation between main antenna and Rx antenna must be at least 10 dB in all uplink frequency bands. Envelope Correlation Coefficient (ECC) value should be as close as possible to zero, for best diversity performance. ECC values below 0.5 on all frequency bands are recommended. GNSS Receiver The LM940 integrates a GNSS receiver that could be used in Standalone mode and in AGPS (assisted GPS), according to the different configurations. LM940 supports an active antenna. Frequency range • Wide-band GNSS: 1560–1606 MHz recommended • Narrow-band GPS: 1575.42 MHz ± 2 MHz minimum • Narrow-band Galileo: 1575.42 MHz ± 2 MHz minimum • Narrow-band BeiDou: 1561.098 MHz ± 2 MHz minimum • Narrow-band GLONASS: 1601.72 MHz ± 4.2 MHz minimum. Gain 1.5 dBi < Gain < 3 dBi Impedance 50 Ohm Amplification 18 dB < Gain < 21 dB Supply Voltage 3.1 V Current consumption 20 mA Typical 7.4.1. GNSS RF Front End Design The LM940 contains an integrated LNA and pre-select SAW filter. This allows the module to work well with a passive GNSS antenna. If the antenna cannot be located near the LM940, then an active antenna (that is, an antenna with a low noise amplifier built in) can be used with an external dedicated power supply circuit. GNSS rescive path uses either the dedicated GNSS connector or the shared AUX connector. 1VV0301352 Rev. 2 Page 46 of 68 2017-07-19 LM940 HW Design Guide NOTE – Please refer to the LM940 AT Commands Reference Guide, 80545ST10791A for detailed information about GNSS operating modes and GNSS Antenna selection. Antenna connection 7.5.1. Antenna Connector The LM940 is equipped with a set of 50 Ω RF U.FL. connectors from Hirose U.FL-R-SMT1(10). The available connectors are: Main RF antenna: TX/RX path Auxiliary RF antenna: Combined Diversity and GNSS GNSS RF antenna: Dedicated GNSS See the picture on the below for their position on the interface. 1VV0301352 Rev. 2 Page 47 of 68 2017-07-19 LM940 HW Design Guide For more information about mating connectors visit the website http://www.hiroseconnectors.com/ 7.5.2. Antenna Cable Connecting cables between the module and the antenna must have 50 Ω impedance. If the impedance of the module is mismatched, RF performance is reduced significantly. If the host device is not designed to use the module’s diversity or GNSS antenna, terminate the interface with a 50Ω load. Minimize Antenna Cable Requirements Impedance 50 Ohm Max cable loss 0.5 dB Avoid coupling with other signals. 7.5.3. Antenna Installation Guidelines Install the antenna in a location with access to the network radio signal. The antenna must be installed such that it provides a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. The antenna must not be installed inside metal cases. The antenna must be installed according to the antenna manufacturer’s instructions. Furthermore, if the device is developed for the US and/or Canada market, it must comply with the FCC and/or IC approval requirements. Information This device is to be used only for mobile and fixed application. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-Users must be provided with transmitter operation conditions for satisfying RF exposure compliance. OEM integrators must ensure that the end user has no manual instructions to remove or install the LM940 module. Antennas used for this OEM module must not exceed gain of below table for mobile and fixed operating configurations. In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the FCC/IC authorization is no longer considered valid and the FCC/IC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC/IC authorization. 1VV0301352 Rev. 2 Page 48 of 68 2017-07-19 LM940 HW Design Guide Manual Information to the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. 1VV0301352 Rev. 2 Page 49 of 68 2017-07-19 LM940 HW Design Guide 8. AUDIO SECTION Audio Interface The LM940 module supports digital audio interfaces. Digital Audio The LM940 module can be connected to an external codec through the digital interface. The product provides a single Digital Audio Interface on the following pins: Digital Audio Interface Signals Pin no. Signal I/O Function Type 51 DVI_WAO PCM Frame Sync B-PD 1.8V 49 DVI_RX PCM Data In B-PD 1.8V 47 DVI _TX PCM Data Out B-PD 1.8V 45 DVI _CLK PCM Clock B-PD 1.8V COMMENT LM940 PCM has the following characteristics: PCM Master mode using short or long frame sync modes 16 bit linear PCM format PCM clock rates of 256 kHz, 512 kHz, 1024 kHz and 2048 kHz (Default) Frame size of 8, 16, 32, 64, 128 & 256 bits per frame Sample rates of 8 kHz and 16 kHz NOTE – If the Digital Audio Interface is not used, the signals can be left floating. 1VV0301352 Rev. 2 Page 50 of 68 2017-07-19 LM940 HW Design Guide 9. MECHANICAL DESIGN General The LM940 module was designed to be compliant with a standard lead-free SMT process. Moreover, it is compatible with the Mini PCIe card 52-pin card edge-type connector. Finishing & Dimensions The LM940 module’s overall dimensions are: Length: 50.95 mm Width: 30.00 mm Thickness: 2.70 mm The module complies with the standard dimensions specified in the PCI Express Mini Card Electromechanical Specification Revision 1.1 Drawing This figure shows the mechanical dimensions of the LM940 module. 1VV0301352 Rev. 2 Page 51 of 68 2017-07-19 LM940 HW Design Guide 10. APPLICATION GUIDE Debug of the LM940 Module in Production To test and debug the mounting of the LM940 module, we strongly recommend to add several test pins on the host PCB for the following purposes: Checking the connection between the LM940 itself and the application Testing the performance of the module by connecting it with an external computer Depending on the customer application, these test pins include, but are not limited to the following signals: SYSTEM_RESET_N, W_DISABLE_N, WAKE_N VBATT, GND VREG_L6_1P8 USB_D-, USB_D+ USB_SS_TX_M, USB_SS_TX_P, USB_SS_RX_M, USB_SS_RX_P In addition, the following signals are also recommended (but not mandatory): WAN_LED_N GPIO_01, GPIO_02, GPIO_03, GPIO_04 Bypass Capacitor on Power Supplies When a sudden voltage step is asserted to or a cut from the power supplies, the steep transition causes some reactions such as overshoot and undershoot. This abrupt voltage transition can affect the device causing it to not operate or to malfunction. Bypass capacitors are needed to alleviate this behavior. The behavior can appear differently depending on the various applications. Customers must pay special attention to this issue when they design their application board. The length and width of the power lines must be considered carefully, and the capacitance of the capacitors must be selected accordingly. The capacitor will also prevent ripple of the power supplies and the switching noise caused in TDMA systems such as GSM. Especially, a suitable bypass capacitor must be mounted on the following lines on the application board: VBATT Recommended values are: 100uF for VBATT Customers must still consider that the capacitance mainly depends on the conditions of their application board. Generally, more capacitance is required when the power line is longer. And if customers use the fast power down function, then more bypass capacitors should be mounted on the application board. 1VV0301352 Rev. 2 Page 52 of 68 2017-07-19 LM940 HW Design Guide EMC Recommendations EMC protection on the pins in the table below should be designed by application side according to the customer’s requirement. EMC Recommendations Pin Signal I/O Function Type Comment USB HS 2.0 Communication Port 38 USB_D+ I/O USB 2.0 Data Plus Analog 36 USB_D- I/O USB 2.0 Data Minus Analog USB SS 3.0 Communication Port 33 USB_SS_RX_P USB 3.0 superspeed receive – plus Analog 31 USB_SS_RX_M USB 3.0 superspeed receive – minus Analog 25 USB_SS_TX_P USB 3.0 superspeed transmit – plus Analog 23 USB_SS_TX_M USB 3.0 superspeed transmit – minus Analog SIM Card Interface 1 14 SIMRST1 Reset output to an external UIM1 card 1.8 / 2.85V 12 SIMCLK1 Clock output to an external UIM1 card 1.8 / 2.85V 10 SIMIO1 I/O Data connection with an external UIM1 card 1.8 / 2.85V 1VV0301352 Rev. 2 Page 53 of 68 2017-07-19 LM940 HW Design Guide SIMVCC1 Supply output for an external UIM1 card 1.8 / 2.85V Power SIM Card Interface 2 SIMRST2 Reset output to an external UIM2 card 1.8 / 2.85V 17 SIMCLK2 Clock output to an external UIM2 card 1.8 / 2.85V 19 SIMIO2 I/O Data connection with an external UIM2 card 1.8 / 2.85V 13 SIMVCC2 Supply output for an external UIM2 card 1.8 / 2.85V Power Digital I/O (GPIOs) GPIO_01 I/O General purpose I/O 1.8V GPIO_02 I/O General purpose I/O 1.8V 44 GPIO_03 I/O General purpose I/O 1.8V 46 GPIO_04 I/O General purpose I/O 1.8V WAKE_N Host wake-up 1.8V 42 WAN_LED_N LED control 1.8V Active Low Power ON/OFF Reset IN/OUT 20 W_DISABLE_N Module & RF ON/OFF Control 1.8V Active Low 22 SYSTEM_RESET_N Reset Input 1.8V Active Low LDO out for 1.8V Power 1.8V Voltage Regulator 11 VREG_L6_1P8 1VV0301352 Rev. 2 Page 54 of 68 2017-07-19 LM940 HW Design Guide All other pins have the following characteristics: Human Body Model (HBM): ± 1000 V Charged Device Model (CDM) JESD22-C101-C: ± 250 V All Antenna pins up to ± 4 kV Warning – Do not touch without proper electrostatic protective equipment. The product must be handled with care, avoiding any contact with the pins because electrostatic discharge may damage the product itself. 1VV0301352 Rev. 2 Page 55 of 68 2017-07-19 LM940 HW Design Guide 11. PACKAGING Tray The LM940 modules are packaged on trays of 20 pieces each. These trays can be used in SMT processes for pick & place handling. 1VV0301352 Rev. 2 Page 56 of 68 2017-07-19 LM940 HW Design Guide 1VV0301352 Rev. 2 Page 57 of 68 2017-07-19 LM940 HW Design Guide 12. CONFORMITY ASSESSMENT ISSUES Approvals Fully type approved confirming with R&TTE directive CE, GCF FCC, IC, PTCRB RoHS and REACH Approvals for major Mobile Network Operators Declaration of Conformity The DoC is available here: www.telit.com/RED/ FCC certificates The FCC Certifcate is available here: www.fcc.gov/oet/ea/fccid IC certificates The IC Certifcate is available here: https://sms-sgs.ic.gc.ca/equipmentSearch/searchRadioEquipments?execution=e1s1&lang=en FCC/IC Regulatory notices Modification statement Telit has not approved any changes or modifications to this device by the user. Any changes or modifications could void the user’s authority to operate the equipment. Telit n’approuve aucune modification apportée à l’appareil par l’utilisateur, quelle qu’en soit la nature. Tout changement ou modification peuvent annuler le droit d’utilisation de l’appareil par l’utilisateur. Interference statement This device complies with Part 15 of the FCC Rules and Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout 1VV0301352 Rev. 2 Page 58 of 68 2017-07-19 LM940 HW Design Guide brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. RF exposure This equipment complies with FCC and ISED radiation exposure limits set forth for an uncontrolled environment. The antenna should be installed and operated with minimum distance of 20 cm between the radiator and your body. Antenna gain must be below: Cet appareil est conforme aux limites d'exposition aux rayonnements de l’ISED pour un environnement non contrôlé. L'antenne doit être installé de façon à garder une distance minimale de 20 centimètres entre la source de rayonnements et votre corps. Gain de l'antenne doit être ci-dessous: WCDMA / LTE Antenna (except Band 30) Brand : HNS (HANKOOK Network Solution) Model Number : WE14-LF-07 Type : Dipole Antenna LTE Antenna for Band 30 Brand : SAE HAN ANTENNA CO.,LTD Model Number : DH-23T-ANT Type : Dipole Antenna Mode Band Antenna Gain (dBi) LTE FDD 2100 – B1 3.5 FDD 1900 PCS – B2 3.5 FDD 1800+ – B3 3.5 FDD 1800 AWS-1 – B4 3.5 FDD 850 – B5 3.0 FDD 2600 – B7 4.0 FDD 900 – B8 3.0 FDD 700a – B12 3.0 FDD 700c – B13 3.0 FDD 700b – B17 3.0 FDD 800 – B20 3.0 1VV0301352 Rev. 2 Page 59 of 68 2017-07-19 LM940 HW Design Guide WCDMA FDD 1900+ – B25 3.5 FDD 850+ – B26 3.0 FDD 700 APT – B28 3.0 FDD 700d – B29 3.0 FDD 2300 WCS – B30 1.5 FDD AWS-3 – B66 3.5 TDD 2600 – B38 4.0 TDD 2300 – B40 4.0 TDD 2500 – B41 4.0 2100 – B1 3.5 1900 PCS – B2 3.5 1800 AWS-1 – B4 3.5 850 – B5 3.0 900 – B8 3.0 This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. L'émetteur ne doit pas être colocalisé ni fonctionner conjointement avec à autre antenne ou autre émetteur. FCC Class B digital device notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 1VV0301352 Rev. 2 Page 60 of 68 2017-07-19 LM940 HW Design Guide Consult the dealer or an experienced radio/TV technician for help. Labelling Requirements for the Host device The host device shall be properly labelled to identify the modules within the host device. The certification label of the module shall be clearly visible at all times when installed in the host device, otherwise the host device must be labelled to display the FCC ID and ISED of the module, preceded by the words "Contains transmitter module", or the word "Contains", or similar wording expressing the same meaning, as follows: L'appareil hôte doit être étiqueté comme il faut pour permettre l'identification des modules qui s'y trouvent. L'étiquette de certification du module donné doit être posée sur l'appareil hôte à un endroit bien en vue en tout temps. En l'absence d'étiquette, l'appareil hôte doit porter une étiquette donnant le FCC ID et l’ISED du module, précédé des mots « Contient un module d'émission », du mot « Contient » ou d'une formulation similaire exprimant le même sens, comme suit : LM940 Contains FCC ID: RI7LM940 Contains IC: 5131A-LM940 CAN ICES-3 (B) / NMB-3 (B) This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de classe B est conforme à la norme canadienne ICES-003. 1VV0301352 Rev. 2 Page 61 of 68 2017-07-19 LM940 HW Design Guide 13. SAFETY RECOMMENDATIONS READ CAREFULLY Be sure the use of this product is allowed in the country and in the environment required. The use of this product may be dangerous and has to be avoided in the following areas: Where it can interfere with other electronic devices in environments such as hospitals, airports, aircrafts, etc. Where there is risk of explosion such as gasoline stations, oil refineries, etc. It is the responsibility of the user to enforce the country regulation and the specific environment regulation. Do not disassemble the product; any mark of tampering will compromise the warranty validity. We recommend following the instructions of the hardware user guides for correct wiring of the product. The product has to be supplied with a stabilized voltage source and the wiring has to be conformed to the security and fire prevention regulations. The product has to be handled with care, avoiding any contact with the pins because electrostatic discharges may damage the product itself. Same cautions have to be taken for the SIM, checking carefully the instruction for its use. Do not insert or remove the SIM when the product is in power saving mode. The system integrator is responsible for the functioning of the final product; therefore, care has to be taken to the external components of the module, as well as any project or installation issue, because the risk of disturbing the GSM network or external devices or having impact on the security. Should there be any doubt, please refer to the technical documentation and the regulations in force. Every module has to be equipped with a proper antenna with specific characteristics. The antenna has to be installed with care in order to avoid any interference with other electronic devices and has to guarantee a minimum distance from the body (20 cm). In case this requirement cannot be satisfied, the system integrator has to assess the final product against the SAR regulation. The European Community provides some Directives for the electronic equipment introduced on the market. All of the relevant information is available on the European Community website: http://europa.eu.int/comm/enterprise/rtte/dir99-5.htm The text of the Directive 99/05 regarding telecommunication equipment is available, while the applicable Directives (Low Voltage and EMC) are available at: http://europa.eu.int/comm/enterprise/rtte/dir99-5.htm 1VV0301352 Rev. 2 Page 62 of 68 2017-07-19 LM940 HW Design Guide 14. REFERENCE TABLE OF RF BANDS CHARACTERISTICS RF Bands Characteristics Mode Freq. Tx (MHz) WCDMA 2100 – B1 1920 ~ 1980 WCDMA 1900 – B2 1850 ~ 1910 WCDMA AWS – B4 1710 ~ 1755 WCDMA 850 – B5 824 ~ 849 Freq. Rx (MHz) 2110 ~ 2170 Channels Tx: 9612 ~ 9888 Tx-Rx Offset 190 MHz Rx: 10562 ~ 10838 1930 ~ 1990 Tx: 9262 ~ 9538 80 MHz Rx: 9662 ~ 9938 2110 ~ 2155 Tx: 1537 ~ 1738 400 MHz Rx: 1312 ~ 1513 869 ~ 894 Tx: 4132 ~ 4233 45 MHz Rx: 4357 ~ 4458 WCDMA 900 – B8 880 ~ 915 925 ~ 960 Tx: 2712 ~ 2863 45 MHz Rx: 2937 ~ 3088 LTE 2100 – B1 1920 ~ 1980 2110 ~ 2170 Tx: 18000 ~ 18599 190 MHz Rx: 0 ~ 599 LTE 1900 – B2 1850 ~ 1910 1930 ~ 1990 Tx: 18600 ~ 19199 80 MHz Rx: 600 ~ 1199 LTE 1800+ – B3 1710 ~ 1785 1805 ~ 1880 Tx: 19200 ~ 19949 95 MHz Rx: 1200 ~ 1949 LTE AWS-1 – B4 1710 ~ 1755 2110 ~ 2155 Tx: 19950 ~ 20399 400 MHz Rx: 1950 ~ 2399 LTE 850 – B5 824 ~ 849 869 ~ 894 Tx: 20400 ~ 20649 45 MHz Rx: 2400 ~ 2649 LTE 2600 – B7 2500 ~ 2570 2620 ~ 2690 Tx: 20750 ~ 21449 120 MHz Rx: 2750 ~ 3449 LTE 900 – B8 880 ~ 915 925 ~ 960 Tx: 21450 ~ 21799 45 MHz Rx: 3450 ~ 3799 LTE 700a – B12 699 ~ 716 729 ~ 746 Tx : 23010 ~ 23179 30 MHz Rx : 5010 ~ 5179 LTE 700c – B13 777 ~ 787 746 ~ 756 Tx : 27210 ~ 27659 -31 MHz Rx : 9210 ~ 9659 1VV0301352 Rev. 2 Page 63 of 68 2017-07-19 LM940 HW Design Guide Mode LTE 700b – B17 Freq. Tx (MHz) 704 ~ 716 Freq. Rx (MHz) 734 ~ 746 Channels Tx: 23730 ~ 23849 Tx-Rx Offset 30 MHz Rx: 5730 ~ 5849 LTE 800 – B20 832 ~ 862 791 ~ 821 Tx: 24150 ~ 24449 -41 MHz Rx: 6150 ~ 6449 LTE 1900+ – B25 1850 ~ 1915 1930 ~ 1995 Tx: 8040 ~ 8689 80 MHz Rx: 26040 ~ 26689 LTE 850+ – B26 814 ~ 849 859 ~ 894 Tx: 8690 ~ 9039 45 MHz Rx: 26690 ~ 27039 LTE 700 APT – B28 703 ~ 748 758 ~ 803 Tx: 9210 ~ 9659 55 MHz LTE 700 d – B29 Downlink only 717 ~ 728 Rx: 9660 ~ 9769 – LTE 2300 WCS – B30 2305 ~ 2315 2350 ~ 2360 Tx: 9770 ~ 9869 45 MHz LTE AWS-3 – B66 1710 ~ 1780 Rx: 27210 ~ 27659 Rx: 27660 ~ 27759 2110 ~ 2200 Tx: 66436 ~ 67335 400 MHz Rx: 131972 ~ 132671 LTE TDD 2600 – B38 2570 ~ 2620 LTE TDD 2300 – B40 2300 ~ 2400 LTE TDD 2500 – B41 2496 ~ 2690 1VV0301352 Rev. 2 2570 ~ 2620 Tx: 37750 ~ 38250 0 MHz Rx: 37750 ~ 38250 2300 ~ 2400 Tx: 38650 ~ 39650 0 MHz Rx: 38650 ~ 39650 2496 ~ 2690 Tx: 39650 ~ 41589 0 MHz Rx: 39650 ~ 41589 Page 64 of 68 2017-07-19 LM940 HW Design Guide 15. ACRONYMS TTSC USB HS DTE UMTS WCDMA HSDPA HSUPA UART HSIC SIM SPI ADC DAC I/O GPIO CMOS MOSI MISO CLK MRDY 1VV0301352 Rev. 2 Telit Technical Support Centre Universal Serial Bus High Speed Data Terminal Equipment Universal Mobile Telecommunication System Wideband Code Division Multiple Access High Speed Downlink Packet Access High Speed Uplink Packet Access Universal Asynchronous Receiver Transmitter High Speed Inter Chip Subscriber Identification Module Serial Peripheral Interface Analog – Digital Converter Digital – Analog Converter Input Output General Purpose Input Output Complementary Metal – Oxide Semiconductor Master Output – Slave Input Master Input – Slave Output Clock Master Ready Page 65 of 68 2017-07-19 LM940 HW Design Guide SRDY CS RTC PCB ESR VSWR VNA FDD I2C LTE SOC 1VV0301352 Rev. 2 Slave Ready Chip Select Real Time Clock Printed Circuit Board Equivalent Series Resistance Voltage Standing Wave Radio Vector Network Analyzer Frequency division duplex Inter-integrated circuit Long term evolution System-on-Chip Page 66 of 68 2017-07-19 LM940 HW Design Guide 16. DOCUMENT HISTORY Revision Date Changes 2017-01-17 First Draft 2017-06-23 Changed document form 2017-07-19 Updated 7. RF section Updated 12.5 RF exposure 1VV0301352 Rev. 2 Page 67 of 68 2017-07-19 [01.2017] Mod.0818 2017-01 Rev.0
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Author : DWKu Create Date : 2017:07:20 18:12:26+09:00 Modify Date : 2017:07:20 17:52:53+08:00 XMP Toolkit : Adobe XMP Core 5.6-c015 84.159810, 2016/09/10-02:41:30 Creator Tool : PScript5.dll Version 5.2.2 Metadata Date : 2017:07:20 17:52:53+08:00 Producer : Acrobat Distiller 10.1.16 (Windows) Format : application/pdf Title : Microsoft Word - 1VV0301352_LM940_HW_User_Guide_R02_20JULY2017 Creator : DWKu Document ID : uuid:3b2d158b-3687-421c-9a29-7eb81f3ba3c2 Instance ID : uuid:c1e5aed8-ae2d-423a-a065-9c7035fde0df Page Count : 68EXIF Metadata provided by EXIF.tools