Texas Instruments 2538EM The CC2538EM is a development tool for the 2.4 GHz CC2538 IEEE802.15.4 System-on-Chip from TI. User Manual CC2538 Development Kit Quick Start Guide

Download:
Mirror Download [FCC.gov]
Document ID	1917558
Application ID	3vwtOhh83zLi/9jZIfyK5w==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	99.51kB (1243843 bits)
Date Submitted	2013-03-14 00:00:00
Date Available	2013-03-15 00:00:00
Creation Date	2013-03-13 14:20:36
Producing Software	Microsoft® Word 2010
Document Lastmod	2013-03-13 14:20:37
Document Title	CC2538 Development Kit Quick Start Guide
Document Creator	Microsoft® Word 2010
Document Author:	Texas Instruments

March 2013
CC2538 Development Kit Quick Start Guide
Opening the Box and Running the Packet Error Rate Test
1. Kit Contents
2. SmartRF06EB Overview
LEDs
EM
Breakout
EM
Connectors
Emulator
LEDs
Main
Power
Switch
20-pin
ARM-JTAG
Connector
Power
Selection
2 x SmartRF06 Evaluation Boards (SRF06EB)
2 x CC2538 Evaluation Modules (CC2538EM)
1 x CC2531 USB dongle (sniffer)
2 x Micro USB Cables
Documentation
10-pin
ARM Debug
Connector
USB
Micro SD
card reader
The RF boards in this kit are FCC and IC
certified and tested/comply with ETSI/R&TTE
over temperature from 0 to 35°C.
3. Plug the EM into the 06EB
LCD
5. Power Options
Buttons
6. Select Power Source
There are several ways of applying power to the
TrxEB.




USB (5V)
2 x 1.5 V AAA batteries
1 x 3.0 V CR2032 coin cell battery
External regulated power supply
There
are
voltage
regulators
on
the
SmartRF06EB that will set the on-board voltage
to 2.1 V or 3.3 V.
Insert
CC2538EM
board
SmartRF06EB as shown above.
into
the
Caution! The kit contains ESD sensitive
components. Handle with care to
prevent
permanent
damage.
To
minimize risk of injury, avoid touching
components
during
operation
if
symbolized as hot.
7. Welcome Screen
Warning! To minimize risk of injury or property
damage, never use rechargeable batteries to
power the board. Always select a power source
that is suitably rated for use with this EVM, not
exceeding 3.6 VDC, with a current output
rating between 0 and 500 mA.
8. Select Channel
The power source is selected using the Source
switch on the left hand side of the SmartRF06EB.
In “USB” position, the EM is powered over USB,
running at 3.3 V. In “BAT” position, the board is
powered from batteries or an external source,
running at 2.1 V. The 2.1 V regulator can be
bypassed by shorting the pins on the “regulator
bypass” jumper. In this case, the EM is powered
directly from the external source or batteries.
Note that there should only be one active
power source at any one time. Do not leave
the EVM powered when unattended.
9. Select Mode
One of the boards must operate as a transmitter
and the other as a receiver.
Select transmitter on one board …
… and receiver on the other board.
Turn on power with the Main Power switch. You
should now see the Texas Instruments logo and
a short description of the buttons on the LCD.
Pushing any of the five buttons on the board will
take you to the main menu.
Select which channel to use for the test.
NB! If you don’t see anything on the screen
make sure the board is correctly powered
(see step 5 and 6 above).
The receiver is now configured.
Web sites:
E2E Forum:
www.ti.com/lprf
www.ti.com/lprf-forum
Make sure to subscribe to the Low-Power RF
Newsletter to receive information about updates to
documentation, new product releases, and more.
Sign up on the TI web pages.
10. Select TX Power
11. Select Burst Size
12. Select Packet Rate
On the transmitter, select desired output power.
On the transmitter, select the desired burst size,
that is, the number of packets to transmit.
On the transmitter, select the desired packet
rate.
13. Start Sending Packets
15. PER Test Results
18. References
The transmitter is now configured and in idle
state. Sending packets is started/stopped by
pressing the Select button.
On the receiver, the statistics window will show
the error rate based on the number of lost or
erreneous packets divided by the total number of
packets that should have been received.
Please visit www.ti.com and
http://www.ti.com/tool/cc2538dk
On the kit product page, you will find additional
documentation, links to updated software
examples and software tools like SmartRF
Studio.
You will also find a lot of information on the TI
E2E forum at http://e2e.ti.com
We hope that you will enjoy working with the
CC2538 device.
17. Troubleshooting
It you are experiencing problems with this test,
please check the following:


Nothing is shown in the display! Make sure
the board is powered correctly (see steps 5
and 6 above).
Please visit the kit web page and check for
updated SW and documentation. Updated
SW can be downloaded to the device using
IAR
EWARM
or
SmartRF
Flash
Programmer.
SmartRF™ Studio
1. Download and Install
2. Launch SmartRF Studio
3. Test the Radio
Before connecting SmartRF06EB to your PC,
download and install SmartRF Studio from
www.ti.com/smartrfstudio.
After installing the tool, connect the EB to the PC
using the USB cable and start SmartRF Studio.
Select the “2.4 GHz” tab and double click the
highlighted CC2538 device icon.
You can now configure the radio, run
performance tests, export register settings and
run link tests with another CC2538 on a
SmartRF06EB connected to the PC.
EVALUATION BOARD/KIT/MODULE (EVM) ADDITIONAL TERMS
Texas Instruments (TI) provides the enclosed Evaluation Board/Kit/Module (EVM) under the following conditions:
The user assumes all responsibility and liability for proper and safe handling of the goods. Further, the user indemnifies TI from
all claims arising from the handling or use of the goods.
Should this evaluation board/kit not meet the specifications indicated in the User’s Guide, the board/kit may be returned within
30 days from the date of delivery for a full refund. THE FOREGOING LIMITED WARRANTY IS THE EXCLUSIVE WARRANTY
MADE BY SELLER TO BUYER AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED, IMPLIED, OR STATUTORY,
INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. EXCEPT TO THE
EXTENT OF THE INDEMNITY SET FORTH ABOVE, NEITHER PARTY SHALL BE LIABLE TO THE OTHER FOR ANY
INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.
Please read the User's Guide and, specifically, the Warnings and Restrictions notice in the User's Guide prior to handling the
product. This notice contains important safety information about temperatures and voltages. For additional information on TI's
environmental and/or safety programs, please visit www.ti.com/esh or contact TI.
No license is granted under any patent right or other intellectual property right of TI covering or relating to any machine,
process, or combination in which such TI products or services might be or are used. TI currently deals with a variety of customers
for products, and therefore our arrangement with the user is not exclusive. TI assumes no liability for applications assistance,
customer product design, software performance, or infringement of patents or services described herein.
REGULATORY COMPLIANCE INFORMATION
As noted in the EVM User’s Guide and/or EVM itself, this EVM and/or accompanying hardware may or may not be subject to the
Federal Communications Commission (FCC) and Industry Canada (IC) rules.
For EVMs not subject to the above rules, this evaluation board/kit/module is intended for use for ENGINEERING
DEVELOPMENT, DEMONSTRATION OR EVALUATION PURPOSES ONLY and is not considered by TI to be a finished end
product fit for general consumer use. It generates, uses, and can radiate radio frequency energy and has not been tested for
compliance with the limits of computing devices pursuant to part 15 of FCC or ICES-003 rules, which are designed to
provide reasonable protection against radio frequency interference. Operation of the equipment may cause interference with
radio communications, in which case the user at his own expense will be required to take whatever measures may be
required to correct this interference.
General Statement for EVMs including a radio
User Power/Frequency Use Obligations: This radio is intended for development/professional use only in legally allocated
frequency and power limits. Any use of radio frequencies and/or power availability of this EVM and its development
application(s) must comply with local laws governing radio spectrum allocation and power limits for this evaluation module. It is
the user’s sole responsibility to only operate this radio in legally acceptable frequency space and within legally mandated power
limitations. Any exceptions to this are strictly prohibited and unauthorized by Texas Instruments unless user has obtained
appropriate experimental/development licenses from local regulatory authorities, which is responsibility of user including its
acceptable authorization.
For EVMs annotated as FCC – FEDERAL COMMUNICATIONS COMMISSION Part 15 Compliant
Caution
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept any interference received, including interference that may
cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.
FCC Interference Statement for Class B EVM devices
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.
For EVMs annotated as IC – INDUSTRY CANADA Compliant
This Class B digital apparatus complies with Canadian ICES-003.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to
operate the equipment.
Concerning EVMs including radio transmitters
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference
that may cause undesired operation of the device.
Concerning EVMs including detachable antennas
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or
lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the
antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that
necessary for successful communication.
This radio transmitter has been approved by Industry Canada to operate with the antenna types listed in the user guide with the
maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in
this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Les changements ou les modifications pas expressément approuvés par la partie responsable de la conformité ont pu vider
l’autorité de l'utilisateur pour actionner l'équipement.
Concernant les EVMs avec appareils radio
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de
l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.
Concernant les EVMs avec antennes détachables
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et
d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage
radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance
isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication
satisfaisante.
Le présent émetteur radio a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés dans le
manuel d’usage et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne
non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation
de l'émetteur.
【Important Notice for Users of this Product in Japan】
This development kit is NOT certified as Confirming to Technical Regulations of Radio Law of Japan
If you use this product in Japan, you are required by Radio Law of Japan to follow the instructions below with respect to this
product:
1.
2.
3.
Use this product in a shielded room or any other test facility as defined in the notification #173 issued by Ministry of Internal
Affairs and Communications on March 28, 2006, based on Sub-section 1.1 of Article 6 of the Ministry’s Rule for
Enforcement of Radio Law of Japan,
Use this product only after you obtained the license of Test Radio Station as provided in Radio Law of Japan with respect
to this product, or
Use of this product only after you obtained the Technical Regulations Conformity Certification as provided in Radio Law
of Japan with respect to this product. Also, please do not transfer this product, unless you give the same notice above
to the transferee. Please note that if you could not follow the instructions above, you will be subject to penalties of
Radio Law of Japan.
Texas Instruments Japan Limited
(address) 24-1, Nishi-Shinjuku 6 chome, Shinjuku-ku, Tokyo, Japan
http://www.tij.co.jp
【ご使用にあたっての注意】
本開発キットは技術基準適合証明を受けておりません。
本製品のご使用に際しては、電波法遵守のため、以下のいずれかの措置を取っていただく必要がありますのでご注意ください。
( 1 ) 電波法施行規則第 6 条第 1 項第 1 号に基づく平成 18 年 3 月 28 日総務省告示第 173 号で定められた電波暗室等の試験設備
でご使用いただく。
( 2 ) 実験局の免許を取得後ご使用いただく。
( 3 ) 技術基準適合証明を取得後ご使用いただく。
なお、本製品は、上記の「ご使用にあたっての注意」を譲渡先、移転先に通知しない限り、譲渡、移転できないものとします。
上記を遵守頂けない場合は、電波法の罰則が適用される可能性があることをご留意ください。
日本テキサス・インスツルメンツ株式会社
東京都新宿区西新宿６丁目２４番１号
西新宿三井ビル
http://www.tij.co.jp
EVALUATION BOARD/KIT/MODULE (EVM)
WARNINGS, RESTRICTIONS AND DISCLAIMERS
For Feasibility Evaluation Only, in Laboratory/Development Environments. Unless otherwise indicated, this EVM is not a
finished electrical equipment and not intended for consumer use. It is intended solely for use for preliminary feasibility
evaluation in laboratory/development environments by technically qualified electronics experts who are familiar with the
dangers and application risks associated with handling electrical mechanical components, systems and subsystems. It should
not be used as all or part of a finished end product.
Your Sole Responsibility and Risk. You acknowledge, represent and agree that:
1.
2.
3.
4.
You have unique knowledge concerning Federal, State and local regulatory requirements (including but not limited to Food
and Drug Administration regulations, if applicable) which relate to your products and which relate to your use (and/or that
of your employees, affiliates, contractors or designees) of the EVM for evaluation, testing and other purposes.
You have full and exclusive responsibility to assure the safety and compliance of your products with all such laws and other
applicable regulatory requirements, and also to assure the safety of any activities to be conducted by you and/or your
employees, affiliates, contractors or designees, using the EVM. Further, you are responsible to assure that any
interfaces (electronic and/or mechanical) between the EVM and any human body are designed with suitable isolation
and means to safely limit accessible leakage currents to minimize the risk of electrical shock hazard.
You will employ reasonable safeguards to ensure that your use of the EVM will not result in any property damage,
injury or death, even if the EVM should fail to perform as described or expected.
You will take care of proper disposal and recycling of the EVM’s electronic components and packing materials.
Certain Instructions. It is important to operate this EVM within TI’s recommended specifications and environmental
considerations per the user guidelines. Exceeding the specified EVM ratings (including but not limited to input and output
voltage, current, power, and environmental ranges) may cause property damage, personal injury or death. If there are
questions concerning these ratings please contact a TI field representative prior to connecting interface electronics including
input power and intended loads. Any loads applied outside of the specified output range may result in unintended and/or
inaccurate operation and/or possible permanent damage to the EVM and/or interface electronics. Please consult the EVM
User's Guide prior to connecting any load to the EVM output. If there is uncertainty as to the load specification, please contact
a TI field representative. During normal operation, some circuit components may have case temperatures greater than 60°C as
long as the input and output are maintained at a normal ambient operating temperature. These components include but are
not limited to linear regulators, switching transistors, pass transistors, and current sense resistors which can be identified
using the EVM schematic located in the EVM User's Guide. When placing measurement probes near these devices during
normal operation, please be aware that these devices may be very warm to the touch. As with all electronic evaluation tools,
only qualified personnel knowledgeable in electronic measurement and diagnostics normally found in development
environments should use these EVMs.
Agreement to Defend, Indemnify and Hold Harmless. You agree to defend, indemnify and hold TI, its licensors and their
representatives harmless from and against any and all claims, damages, losses, expenses, costs and liabilities (collectively,
"Claims") arising out of or in connection with any use of the EVM that is not in accordance with the terms of the agreement.
This obligation shall apply whether Claims arise under law of tort or contract or any other legal theory, and even if the EVM
fails to perform as described or expected.
Safety-Critical or Life-Critical Applications. If you intend to evaluate the components for possible use in safety critical
applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal
injury or death, such as devices which are classified as FDA Class III or similar classification, then you must specifically notify
TI of such intent and enter into a separate Assurance and Indemnity Agreement.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Page Count                      : 6
XMP Toolkit                     : 3.1-701
Part                            : 1
Conformance                     : B
Producer                        : Microsoft® Word 2010
Creator Tool                    : Microsoft® Word 2010
Create Date                     : 2013:03:13 14:20:36+01:00
Modify Date                     : 2013:03:13 14:20:37+01:00
Title                           : CC2538 Development Kit Quick Start Guide
Creator                         : Texas Instruments
Author                          : Texas Instruments

EXIF Metadata provided by EXIF.tools