Thales e Transactions ARTMOB001 Mobile EFT-Terminal - Artema Mobile (GPRS) User Manual artemain01

Thales e-Transactions GmbH Mobile EFT-Terminal - Artema Mobile (GPRS) artemain01

Exhibit 8 User manual

Thales ARTEMA mobile GSM/GPRS
INSTALLATION MANUAL
THALES e-TRANSACTIONS
Thales e-Transactions, Inc.
53 Perimeter Center East
Suite 175
Atlanta, GA
30346
USA
Tel: +1 888-726-3900
Fax: +1 770-393-2177
www.thales-e-transactions.com
Thales Service Center, Attn: TP
509 Medtech Parkway
Johnson City, TN
37604
USA
Tel: +1 888-710-000
www.thales-e-transactions.com
2 Installation Manual ARTEMA mobile GSM / GPRS
This document is subject to change without notice. All rights reserved.
Copyright © 2004 by Thales e-Transactions 444C017-002/01
Note
No warranty or assurance is made by Thales e-Transactions that ARTEMA mobile
GSM / GPRS is usable for a specific purpose. Thales e-Transactions does not
take responsibility for subsequent errors or damages that are caused by the
content or application of this installation manual.
This information is proprietary of Thales e-Transactions and may not be used,
copied, disclosed or divulged, in whole or in part, for any purpose by any person
without the prior written approval of Thales e-Transactions.
3Installation Manual ARTEMA mobile GSM / GPRS
List of Contents
Safety Precautions ................................................................................................. 4
Important Notes ..................................................................................................... 8
Product Description ............................................................................................. 10
Softkeys and Icons .............................................................................................. 11
Installation ............................................................................................................ 12
Insert / remove SIM card .................................................................................. 12
Insert / change plug-in card .............................................................................. 14
Battery Pack Handling ...................................................................................... 15
Important note for the use of battery packs...................................................... 15
Connect Power Supply..................................................................................... 16
Paper Roll ............................................................................................................ 18
Technical Specification......................................................................................... 19
Getting Started ..................................................................................................... 20
Short maintenance Guide .................................................................................... 20
Mobile Phones (...Devices) Health ....................................................................... 21
RF Exposure Statement....................................................................................... 22
4 Installation Manual ARTEMA mobile GSM / GPRS
Safety Precautions
Battery Quality
In addition to the battery pack of the handset,
ARTEMA uses Lithium batteries in order to
backup internal data. The Lithium batteries under
normal usage conditions have a 6 year life
expectancy. These batteries should only be
replaced by an approved servicing center.
Lithium Batteries
Danger of explosion if battery is incorrectly
replaced. Replace only with the same or
equivalent type recommended by the
manufacturer. Dispose of used batteries
according to the manufacturers instructions.
Caution:
Dont short, burn, heat, open the lithium battery.
Battery Pack
Other battery packs may damage ARTEMA mo-
bile GSM / GPRS. In these cases the
manufacturer cannot be held responsible.
4432-107-000 NiMH or
Dont throw old or damaged lithium batteries into
the house trash. Dispose of used or damaged
lithium batteries according to statutory
requirements. Incomplete discharged lithium
batteries have to be isolated by means of
wrapping with adhesive tape or by putting into a
plastic bag to prevent short cuts.
The terminal is supplied by a battery pack.
Dont short, burn, heat, open the battery packs.
Never use other battery packs than Thales
battery packs!
Types: 4432-102-000 NiCd.
The capacity of your ARTEMA mobile GSM /
GPRS battery pack reduces each time you
charge / discharge it. Storing the battery at
temperatures that are too high or too low also
causes a gradual loss of capacity. This can cause
the operating times of your ARTEMA mobile
GSM / GPRS to reduce significantly per usage
cycle. The battery is, however, designed to be
charged and fully discharged within a period of
5Installation Manual ARTEMA mobile GSM / GPRS
Safety Precautions
Dont throw old or damaged battery packs into
the house trash. Dispose of used or damaged
batteries according to statutory requirements.
six months from the time when ARTEMA mobile
GSM / GPRS was purchased. Following this six-
month period, it is recommended replacing the
battery if you experience a significant drop in
performance. Please purchase only Thales e-
Transactions original batteries.
Remove the battery pack if you are not going to
use ARTEMA mobile GSM / GPRS for extended
periods of time.
Important
Installation Note
For security reasons the battery shall not be
inserted in the device during transportation.
The device is delivered with an incomplete
charged battery pack. Unconditionally the battery
pack must be fully charged before using the
device. To gain the best battery performance the
battery pack must be charged according to the
installation manual. New battery packs should be
fully charged within a periode of 3 months after
delivery.
Before storage the battery pack must be removed
from the device. Discharged battery packs shall
not remain inserted in the device for an extended
storage. Improper use may result in battery
damage.
Operate and store the battery pack within the
temperature limits according to the ratings in the
installation manual. Exceeding the temperature
limits may result in gradual loss of capacity or
damage of the battery pack.
Please handle battery packs according to the
recommendations above for best battery
performance and life time. Malfunctions that are
caused by improper use or damaged battery
packs void warranty and any repairs are subject
to charges.
6 Installation Manual ARTEMA mobile GSM / GPRS
Safety Precautions
Switch off near petrol stations, fuel depots,
chemical plants or blasting operations.
Switch off in hospitals; medical equipment such
as pacemakers and hearing aids may be
affected.
In explosive
environment
In medical
environment
Cautiously use ARTEMA
mobile GSM / GPRS
In vehicles with
airbags
ARTEMA mobile GSM / GPRS must not im-
pair the proper operation of vehicle functions
(such as airbag). Never place ARTEMA
mobile GSM / GPRS next to airbags or its
propagation directions. Improper placement
may cause serious injury in cause of airbag
activation.
Mobile units must be switched off at all times
in an aircraft. Prevent accidential activation.
In aircrafts
In vehicular
environment
Dont use mobile units such as ARTEMA mo-
bile GSM / GPRS other than described in the
Users Manual of your vehicle. Switch off while
driving.
General All radio transmitter such as ARTEMA mobile
GSM / GPRS are subject to restrictions. Ra-
dio transmitter may impair improper shielded
electronic equipment.
Warnings Switch off ARTEMA mobile GSM / GPRS in
any area where radio transmitters are
prohibited.
Dont touch the metallic parts of the rear
connector (next to the SIM card connector)
with your fingers or any other objects.
Electrostatic discharge (ESD) may impair
ARTEMA mobile GSM / GPRS.
Do not use magnifying glasses or the like to
view the infrared port during operation.
The Artema must be located at a minimum
of 20 cm from all persons, and must not be
co-located or operated in conjunction with
any other antenna or transmitter.
7Installation Manual ARTEMA mobile GSM / GPRS
Compliance
information
Warranty Do not try to repair ARTEMA mobile GSM /
GPRS. There are no serviceable parts inside.
Warranty will void if the warranty seal is broken.
In case of malfunctions please refer to your
local service provider.
Any misuse or service by non-
authorized personnel voids the
warranty and could damage the unit
and/or create a hazard.
This device complies with part 15 of the FCC
rules. Operation is subject to following two
conditions:
1. This device may not cause harmful
interference, and
2. This device must accept any interference
received, including interference that may
cause undesired operation.
Safety Precautions
Caution: Plug-in and SIM cards can be
removed; keep away from children; small parts
could be swallowed by children.
Plug-In / SIM card
Before changing the SIM card refer to the
Users Manual.
Loss / theft In case you lose your ARTEMA mobile GSM
/ GPRS and / or the plug-in / SIM card
contact your Service Provider immediately to
prevent misuse.
SIM card Please consider that prepaid cards have a
limited credit. When the credit expires no more
online transations or telephone calls are
possible. Please verify that your SIM card is
enabled for data transmission.
FCC-ID: RNUARTMOB001
8 Installation Manual ARTEMA mobile GSM / GPRS
Protect ARTEMA mobile GSM / GPRS
against dust and high humidity. This may
impair the smart card reader.
Operate ARTEMA mobile GSM / GPRS in
dry environment only and in a temperature
range from +5°C to +40°C.
Do not expose ARTEMA mobile GSM /
GPRS to direct sunlight or excessive heat
sources. High environmental temperature
may damage the terminal.
Do not insert any objects or pour fluid
into the terminal or the smart card
reader. This may damage the terminal.
Place the terminal away from excessive
heat sources, vibrations, dust, water and
strong radio sources.
Locations for use
Temperature and
Environment
Disconnect ARTEMA mobile GSM / GPRS
from main power before cleaning it. Clean
ARTEMA mobile GSM / GPRS with light
moist cloth or an antistatic cloth. Dont use
chemical cleaning agent.
Cleaning and
Maintenance
Never use cleaning fuel, paint thinner or
any other solvent. These chemicals may
deform or discolor the plastic housing.
Important Notes
Operate ARTEMA mobile GSM / GPRS in
an adequate distance from radio devices to
avoid disturbance of the electronic circuits.
Store ARTEMA mobile GSM / GPRS in dry
environment only and in a temperature
range from -20°C to +60°C.
Attention: Storage temperature of battery
pack: -20°C to +30°C. Store battery pack
separate from terminal if necessary.
Operate ARTEMA mobile GSM / GPRS in
an adequate distance from strong magnetic
fields devices to avoid disturbance of the
magnetic swipe card reader.
9Installation Manual ARTEMA mobile GSM / GPRS
Important Notes
Lithium Battery Caution A lithium battery protects the Random
Access Memory (RAM) in the ARTEMA
mobile GSM / GPRS. Do not, under any
circumstances, attempt to replace this
battery. Failure to comply may invalidate the
product warranty.
No Warranty Although Thales e-Transactions has
attempted to ensure the accuracy and
completeness of its contents, this manual
may contain errors or omissions.
Limited Liability In no event shall Thales e-Transactions be
liable for any indirect, special, incidental, or
consequential damages (including
damages for loss of business, profits, or
the like), even if Thales e-Transactions or
its representatives have been advised of
the possibility of such damages.
Product Changes Thales e-Transactions reserves the rights
to change, update, or render obsolete any
product changes at any time and without
notice. Document Title: ARTEMA mobile
GSM / GPRS Installation Guide.
No part of this publication may be copied,
distributed, stored in a retrieval system,
translated into any human or computer
language, transmitted, in any form or by
any means, without prior written consent of
Thales e-Transactions.
Warranty Do not try to repair ARTEMA mobile GSM /
GPRS. There are no serviceable parts inside.
Warranty will void if the warranty seal is broken.
In case of malfunctions please refer to your
local service provider.
Any misuse or service by non-
authorized personnel voids the
warranty and could damage the unit
and/or create a hazard.
10 Installation Manual ARTEMA mobile GSM / GPRS
Product Description
General
Smart Card Reader ARTEMA mobile GSM / GPRS includes a
magnetic stripe card reader and additionally a
smart card reader. These interfaces support
all standard smart, magnetic stripe or hybrid
payment cards as well as a wide range of
additonal cards such as loyalty or memory
cards.
The integrated thermal line printer is used to
print receipts, diagnosis printouts, SMS text,
emails and device specific information.
Printer
Supported networks ARTEMA mobile GSM / GPRS operates a
dual-band GSM engine for use in GSM850 and
PCS1900 networks.
ARTEMA mobile GSM / GPRS is a wireless
payment terminal. It can be used to perform
credit as well as debit card transactions with
smart cards and magnetic stripe cards. The
integrated GSM engine and the integrated
antenna support the use in GSM850 and in
PCS1900 public land mobile networks. The
terminal offers functionalities similar to a
standard mobile phone. The terminal can be
used to make telephone calls, send / receive
emails and SMS.
Interfaces ARTEMA mobile GSM / GPRS has a
multifunctional interface at the rear side of the
terminal. This interface can be used to connect
accessory such as power supply or car
charger.
ARTEMA mobile
GSM / GPRS
11Installation Manual ARTEMA mobile GSM / GPRS
The battery charge icon (1 to 4 bars)
indicates the charge level of the battery.
Battery icon:
Enter key.
Power on key; select function; select menu.
Cancel key.
Navigation key up.
Navigation key down.
Correction key.
Softkeys
Number sign; 00.
Icons
The signal strength indicator indicates the
received signal strength of the mobile
network.
Sub-menu icon. Additional sub-menus can be
called pressing the key .
The battery icon flashes if the battery
capacity is too low to perform an additional
transaction.
= battery almost empty
= battery fully charged
Paper feed icon. Select the key to feed
the paper.
Softkeys and Icons
OK
#
CLR
CAN
ENT
1 block
2 blocks
3
4 blocks
= medium
= strong
blocks = maximum
= lowTable of signal strength:
Note:
It is required to enter the main menu, before
switching off the terminal.
12 Installation Manual ARTEMA mobile GSM / GPRS
Installation
ARTEMA mobile GSM / GPRS
(bottom view)
The Service Provider supplies you with a SIM
card and a personal identification number
(PIN). The SIM card contains all important
data (e.g. telephone number) for your GSM
communication stored in a chip.
Only 3 Volt SIM cards are supported. Older
SIM cards (5 Volts technology) cannot be
used.
Attention: In order to perform payment
transactions data transmission must be
enabled by the Service Provider.
SIM card Chip
Sloping edge
Insert / remove SIM card
Multifunctional
interface
SIM card
holder
Battery pack
Before changing the SIM card
Caution: Do not touch the contact pads of
the SIM card or of the multifunctional
interface.
Refer to your users manual for the PIN
handling of your SIM card.
Caution: Keep SIM card away from children;
small parts could be swallowed by children.
13Installation Manual ARTEMA mobile GSM / GPRS
Insert SIM card
Push the SIM card release button with a
pointed object such as a ballpen. The SIM
card holder will eject slightly.
Remove the SIM card holder.
Unlock
Insert the SIM card holder (including the
SIM card) like a drawer into the SIM card
slot according to the drawing. Push the
drawer until it is blocked.
Now ARTEMA mobile GSM / GPRS can
be powered on again by pressing the
key.
SIM card with SIM
card holder
Caution: Do not touch!
SIM card in a credit card format:
Cut carefully the small bridges
between inner and outer card.
Press carefully and take out SIM card.
SIM card
Switch off ARTEMA mobile GSM / GPRS
by pressing the key .
Insert the SIM card in the SIM card holder
as shown in the drawing. Pay attention to
the orientation of the SIM card. The
metallic pads must be visible and the SIM
cards sloping edge has to fit in the card
holders sloping edge.
CLR
OK
Installation
14 Installation Manual ARTEMA mobile GSM / GPRS
Plug-in card
For the operation of some payment and
loyalty cards plug-in cards need to be
inserted into the terminal. These cards are
supplied by your local dealer/provider or
bank.
Push the battery pack interlocking pin as
shown in the drawing and lift it up to
remove the battery pack.
Switch off the terminal by pressing the
key before inserting or removing the
plug-in card.
Insert / change plug-in card
Before changing the plug-in card
Insert plug-in card
Bottom view
Push
Battery pack
Caution: Keep away from children; small
parts could be swallowed by children.
CLR
Push the flap of the chip card connector
as ... shown in the drawing and open
the flap.
Caution: Do not touch the metal pads of
the plug-in cards or electronic devices with
your fingers or other objects. Electrostatic
discharge (ESD) may cause damage.
Installation
Do not
touch!
2
4
3
1
1 4
15Installation Manual ARTEMA mobile GSM / GPRS
Flap Chip
Chip card
connector
Plug-in card
Insert the plug-in card completely into the
flap as shown in the drawing.
Close the flap and push it into the direction
as shown.
Lock
Switch on ARTEMA mobile GSM / GPRS
by pressing the power on key .
After changing the plug-in card
Position the battery pack in the back of the
terminal. Press on the upper part of the
battery until a click is heard.
OK
Installation
The battery pack heats up during charging
and discharging. This is normal and not
dangerous.
Important note for the use of
battery packs
Caution:The use of battery packs other
than recommended may cause mal-
functions or may damage ARTEMA mobile
GSM / GPRS. In this case Thales e-Trans-
actions cannot be held responsible!
Replace old batteries only by original
batteries recommended by Thales e-
Transactions.
The battery pack supplies the terminal with
power.
Battery Pack Handling
16 Installation Manual ARTEMA mobile GSM / GPRS
Note: The battery pack reaches its maximum
capacity after charging with the delivered
power supply.
Important: Switch off ARTEMA mobile
GSM / GPRS by pressing the power off
key before changing the battery pack.
Push the battery pack interlocking pin as
shown in the drawing and lift it up to
remove the battery pack.
Position another battery pack in the back of
ARTEMA mobile GSM / GPRS and press
on the battery upper part until a click is
heard.
Switch on ARTEMA mobile GSM / GPRS
by pressing the power on key .
Bottom view
Push
Battery
pack
Before changing the battery
Insert battery back
Spare batteries:
Type: NiMH, 7.2 Volt, 1500 mAh
Order code: 4432-107-00
Type: NiCd, 7.2 Volt, 700 mAh
Order code: 4432-102-00
CLR
OK
Installation
Do not store battery inserted in the terminal
for a prolonged period of time.
Multifunctional interface for the
power supply or car charger.
ARTEMA mobile GSM / GPRS
(Rear view)
Connect Power Supply
Caution: Do not operate ARTEMA mobile
GSM / GPRS without inserted battery
pack!
The battery level icon at the ARTEMA
mobile GSM / GPRS display flashes if the
battery is nearly empty. The terminal refuses
to perform additional transactions. Connect
ARTEMA mobile GSM / GPRS to the power
supply to recharge the battery pack.
17Installation Manual ARTEMA mobile GSM / GPRS
Installation
110-240 VAC
50-60 Hz
ARTEMA mobile GSM / GPRS
with power supply
Power supply
Compress
Compress
Caution: Do not touch the metal pads of the
multifunctional interface with your fingers or
other objects. Electrostatic discharge (ESD)
may damage the device.
Note: Battery pack reaches its maximum
capacity by charging and discharging several
times.
Connect the provided power supply to the
multifunctional interface of ARTEMA
mobile GSM / GPRS properly.
Connect the power supply to the wall outlet.
The electrical outlet needs to be close to
the terminal, within reach, in order to quickly
disconnect the terminal if necessary.
Caution: The battery pack inside ARTEMA
mobile GSM / GPRS has to be charged with
the delivered power supply only. The use of
other power supplies than recommended can
cause malfunctions or can damage ARTEMA
mobile GSM / GPRS. In this case Thales e-
Transactions cannot be held responsible.
Charging time: An empty NiMH battery is
fully charged after 2.5 hours. An empty NiCd
battery is fully charged after about 4 hours.
Charging of batteries is only permitted in an
ambient temperature of 5°C to 40°C.
Please disconnect the power supply from
ARTEMA mobile GSM / GPRS and the po-
wer supply from the wall outlet after the
battery is fully charged.
Note: Compress the connector sides to
connect or to remove the plug.
Caution: Connecting or removing the plug
without compressing the connector sides will
damage your ARTEMA!
18 Installation Manual ARTEMA mobile GSM / GPRS
To obtain the highest printing quality, and to
ensure maximum printer life span, only use
recommended paper rolls.
Paper Roll
Open the printer casing by pressing
simultaneously on both sides, and by
pulling upwards.
1.
Open the paper cover completely and
remove the old paper roll.
2.
Paper cover
Place the new roll of paper in the casing,
paper output towards the keypad. Leave a
few centimeters / inches of paper outside.
3.
Paper roll specification:
Width
Roll diameter
Paper thickness
Paper color
Developing color
Thermal sensitivity
Core diameter
58mm +0/-1,0 mm
65µm + 5/-7µm
white
black
standard
12 mm (0.47 inch)
:
:
:
:
:
:
max 45 mm (1.77 inch)
:
Paper thermal paper:
4. Close the printer casing. You will hear a
click to confirm the casing is closed.
Note: The printer will work only if the
casing is closed and the battery is
sufficiently charged.
Switch on ARTEMA mobile GSM / GPRS
by pressing the power on key and
draw a few centimeters / inches to check
the roll is correctly placed in its casing.
5.
OK
(2.28 inch +0/-0.04 inch)
19Installation Manual ARTEMA mobile GSM / GPRS
Dimensions
Printer
Graphics display
Keyboard
Card Readers
Microprocessor
Battery pack
9.45 x 3.54 x 2.56 inch (240 x 90 x 65 mm)
thermal line printer 12 lines/seconds
132 x 40 pixels, backlight
silicon rubber keypad, 17 keys, backlight
2-track magnetic swipe card reader
(ISO track 2+3 or 1+2 or 2)
smart card reader IS=/IEC 7816/1-3
32-bit RISC processor
Nickel-Metal-Hydrid battery pack 7.2 Volt, 1500mAh;
Nickel-Cadmium battery pack 7.2 Volt, 700mAh
Technical Specification
Weight 700 g
4 plug-in connectors
Interfaces RS232 interface, up to 115 kbps; multifunctional
interface for accessory: car charger, power supply
Mobile networks GSM850/PCS1900
SIM card ID000, 3 Volt
Protocols V.32, V.110, TCP / IP
Accessory
(optional)
spare battery pack, car charger
ARTEMA mobile GSM / GPRS
Application
Power supply special plug-in AC power unit
100-240 VAC 50-60 Hz 12 VDC
wireles electronic transaction via GSM850/PCS1900
networks
Operating temperature 41°F (+5°C) to 104°F (+40°C)
at 15% to 85% rel. humidity non condensing
Storage temperature -4°F (-20°C) to 140°F (+60°C) at
10% to 90% rel. humidity non condensing
Environment
terminal
Charging/discharging temperature 41°F (+5°C) to 104°F
(+40°C) at 15% to 85% rel. humidity non condensing
Storage temperature -4°F (-20°C) to (86°F) +30°C at
45% to 85% rel. humidity non condensing
Environment
battery
Memory Flash 4 MB / SRAM 512 KB
20 Installation Manual ARTEMA mobile GSM / GPRS
Short Maintenance Guide
Technical maintenance operations should only be done by approved
servicing centers.
Some problems can easily be solved:
ARTEMA stops during transaction
processing or printing:
Recharge the battery by connecting the
belonging power supply for several hours.
Check if the battery is correctly set in the
hand held unit.
Check if the printer casing is correctly closed.
The hand held unit is not
communicating with the network:
Check the signal strength of the network
(look for radio icon on hand held unit).
Paper jams: Check that the paper roll is correctly placed.
Check that the paper casing is correctly
closed.
Spare parts:
Contact your terminal provider for spare parts and servicing.
To start to work with ARTEMA mobile GSM / GPRS please refer to the supplied
Users Manual.
Getting Started
21Installation Manual ARTEMA mobile GSM / GPRS
According to FDA and others, the research to date does not show that mobile
phone (...device) radio frequency emissions have adverse health effects but there
is not enough information at this point to conclude that these products are without
risk. While most epidemiological and laboratory studies related to the radio frequency
emissions of mobile phones (...devices) have found no adverse health effects, the
results of some studies have raised questions that require further research.
Mobile Phones (...Devices) Health Issues
A number of studies have been conducted on the possible health effects of Radio
frequency emissions from mobile phones. FDA's position, first stated in 1993 and
still in place today, is that the research to date does not show that radio frequency
emissions from mobile phones (...devices) have adverse health effects. However,
according to FDA, there is not enough information at this point to conclude that the
phones pose no risk. Several international bodies, including the World Health
Organization1) and Expert panels commissioned by the British2) and Canadian3)
governments, have drawn similar conclusions. All of these bodies conclude that
while most of the studies related to mobile phone (...device) radio frequency
emissions have found no effect on human health, some studies that have suggested
the existence of biological effects require further investigation.
[Citation: Page 8 GAO-01-545 "Research and Regulatory Efforts on Mobile Phone
Health Issues", 5/2001, Washington, DC, J.I. Lieberman, E.J. Markey]
FDA - US Food and Drug Administration
GAO - US General Accounting Office
RF - Radio Frequency
SAR - Specific Absorption Rate
WHO - World Health Organisation
3) Royal Society of Canada, "A Review of the Potential Health Risks of Radio
frequency Fields From Wireless Telecommunication Devices." Expert panel
report prepared for Health Canada (1999).
2) Independent Expert Group on Mobile Phones, "Mobile Phones and Health,
National Radiological Protection Board (UK) (Apr. 1999).
1) World Health Organisation, "Electromagnetic Fields and Public Health: Mobile
Telephones and Their Base Stations," Fact Sheet No. 193 (2000).
22 Installation Manual ARTEMA mobile GSM / GPRS
RF Exposure Statement
Your Artema may contain a transmitter and receiver that emit radio frequency
(RF) energy. The actual frequency range used by the Artema is radio-modem
dependent according to the specific model. Digital modulation techniques are
used. During radio communication, the local radio system handling the actual
communication controls the actual power transmission output level. This
output level may typically vary (relative to the distance between the user
location and the cell transmission sites).
* When used properly, the design of this hand-held wireless terminal complies
with U.S., Canadian, European and other standards for protection from public
exposure to radio frequency (RF) magnetic signals.
* This device has been tested and meets RF exposure guidelines for hand held
operation pursuant to FCC OET Bulletin 65 Supplement C ed. 01-01,
IEEE 1528/D1.2 (2003).
23Installation Manual ARTEMA mobile GSM / GPRS
Thales ARTEMA mobile GSM/GPRS
INSTALLATION MANUAL
THALES e-TRANSACTIONS
Thales e-Transactions, Inc.
53 Perimeter Center East
Suite 175
Atlanta, GA
30346
USA
Tel: +1 888-726-3900
Fax: +1 770-393-2177
www.thales-e-transactions.com
Thales Service Center, Attn: TP
509 Medtech Parkway
Johnson City, TN
37604
USA
Tel: +1 888-710-0100
www.thales-e-transactions.com

Navigation menu