The Genie a Division of Overhead Door 315390K Remote Control Transmitter for Garage Door Opener Operation User Manual 37257501192 ODC WK English

The Genie Company a Division of Overhead Door Corporation Remote Control Transmitter for Garage Door Opener Operation 37257501192 ODC WK English

Exhibit D Users Manual per 2 1033 b3

STEP 1:This Wireless Keypad is compatible with all and CODEDODGER® 2 radio equipped GENIE® products.sDrill with 1/16" Drill Bit sPhillips Screwdriver sPencilsMounting Screws INCLUDED sAbility to Control up to three Overhead Door®CODEDODGER®1 or 2 OpenerssSimple to Program and Install sPIN Codes can be up to 8 Characters sLow Battery Power IndicatorsStays Programmed During Battery Change sTemporary PIN for Special Purpose AccessOPERATING INSTRUCTIONS(KEEP FOR FUTURE REFERENCE)37257501192STEP 3:Following programming—On your Wireless Keypad: Enter your PIN.OPERATING DOOR OPENERSProceed to Section 3 - Mounting Instructions.MOUNTING INSTRUCTIONSThe Keypad must be mounted in sight of the Door(s), at least 5 feet above the ground and clear of any moving Door parts.AMount Keypad.(Mounting screws located inside Battery Compartment.)sRemove Battery Cover and batteries. (See Figure 3).sDrill a 1/16”pilot hole for the top mounting screw.sInstall a screw into the drilled hole,leaving a 1/8" gap between the screw headand the wall. (See Figure 2.)sHook the Keypad over the screw.sMark and drill pilot hole and fasten bottom screw.snstall Batteries and Cover.For answers to questions,call 1-800-275-6187 , or visitwww.overheaddoor.comOverhead Door Corp., 2501 S State Hwy.,Suite 200, Lewisville, TX75067. Additional products can be ordered through localOverhead Door® Professional Dealers. To locate a dealer near you, call 1-800-929-DOOR.SECTION2SECTION3ADDITIONAL OPERATIONSSECTION4USING ATEMPORARYPIN A temporary PIN allows temporary access to your home byIf you have forgotten your PIN or you fear it may have fallen into unauthorized hands, you must erase the old programming.repair persons, meter readers, etc.if you so desire.NOTEDONOT reprogram the Door Opener(s).sTemporary PIN remains active only until the next timenyour ormal PIN is entered.FORGOTYOURPIN (RESETTING WIRELESS KEYPAD)CHANGINGYOURPINEnter your current PIN and press .Wallscrew head gapFigure 2FOR CONVENIENCEProgram Keypad BEFORE mounting.MULTIPLEFEATURES:TOOLSNEEDED: 2YHUKHDG'RRU&RUSRUDWLRQFCC and IC CERTIFIEDThis device complies with FCC Part 15 and RSS 210 of Industry Canada. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which may be determined by turning the equipment OFF and ON, the user is encouraged to try to correct the interference by one or more of the following measures:s Re-orient or relocate the receiver antenna.s Increase the separation between the opener and receiver.s Connect the opener into an outlet on a circuit different from that to which the receiver is connected.s Consult your local dealer. CHANGINGBATTERYNOTEsIf the Door does not move,check the LED on Keypad. If the LED is blinking rapidly,the PIN was entered incorrectly. After the LED stops blinking,re-enteryour PIN and try again.sAny Keypad Button will control the Door for 30 seconds after the Door starts moving.sRapid blinking of the red LED indicates an error. After a few seconds the LED will turn off. Start over.If your garage door opener has a Serial Numbersticker which looks like this, in which the first two numbers are 10 or higher, your opener is equipped with CODEDODGER®2. Follow the instructions on this page. Otherwise, follow the instructions on back.sPress in order .sPress . sEnter your PIN (3 to 8 characters).ssClose keypad cover and wait 30 seconds.Press . 3 5 7STEP 1: CREATING YOUR WIRELESS KEYPAD PIN(PERSONALIDENTIFICATIONNUMBER)ssssssssss1 2 3Enter your current PIN and press 3 times.Press and hold . Release both buttons. You must now start from the beginning and reprogram your Wireless Keypad. Wile holding press and hold for 5 seconds.Enter your NEW PIN and press .Enter your TEMPORARY PIN and press .sPress the number of the door you wish to operate or .sPress any key to operate the door. ssPress . + AAA -+ AAA -If the Keypad backlight does not come on, this indicates the need to replace the batteries.Figure 3PressherePolaritymarkingsBatteryCoverPress in on the front of the battery cover and slide it down off of the Keypad. Remove used batteries and replace sNo programming is lost during replacement of batteries. with "AAA." Make sure the batteries are inserted properly using the polarity markings. ATTENTION2MODEL AC SR3 OVERHEAD DOOR CORP.FCC ID: B8Q AC SR3 Residential Door OperatorIC: 2133A-CSD1D 120V. 60HZ. 5A FOR HELP CALL 1-800-275-6187 OR WWW.OVERHEADDOOR.COM InterchangeableFlip-up Cover available in 3 optional Classic Colors to match your home’sexterior decorGREEN LED indicates Pre-SettoIntellicode® 2 BacklitKeypad for Ease of Use at NightBattery Compartment2 AAA Batteries(included)ProgramButtonCovers available in:sTan - P/N 37227TsAlmond - P/N 37227UsGray- P/N 37227SsWhite- - P/N 37227RSTEP 3: OPERATING ONE DOOR OPENERATo open or close the Garage Door.sEnter your PIN.sPress .FOR CONVENIENCEProgram Keypad BEFORE mounting.SECTION1Proceed to Section 3 - Mounting Instructions.NOTEsIf the Door does not move,check the LED on Keypad. If the LED is blinking rapidly,the PIN was entered incorrectly. After the LED stops blinking,re-enteryour PIN and try again.sAny Keypad Button will control the Door for 30 seconds after the Door starts moving.sRapid blinking of the red LED indicates an error. After a few seconds the LED will turn off. Start over.Wait until Keypad Backlight turns off (approximately 30 seconds).STEP 1: CREATING YOURSTEP 2:PROGRAMMING SINGLE DOOR OPENERWIRELESS KEYPAD PIN(PERSONALIDENTIFICATIONNUMBER)sPress in order .sPress . sEnter your PIN (3 to 8 characters).ssClose keypad cover and wait 30 seconds.Press . 3 5 7 Figure 1Press and hold until both LEDs turn BLUE. s On the Wireless Keypad—enter your PIN.s Press . LEDs will stay on solid.s Press again. LEDs will turn off.s Press again. Door opener should run.s Press any key to stop opener. (It will automatically stop at the fully open or fully closed position.)PROGRAMSETsPress , release again. Long LED should blink PURPLE. s Release button. Only round LED will be BLUE.Figure 1SETPROGRAMOpen TravelButtonROUND LEDLONG LED CloseTravelButtonON THE OPENERS/N:10XXXXXXXXXXXXIPROGRAMPROGRAMPROGRAMPROGRAMPROGRAMPROGRAMPROGRAMPROGRAMPROGRAMPROGRAMA Moving Door can cause serious injury or death.1Keep3Wall Control should be mounted within sight of door, at least 5 feet above floor and clear of moving parts. people clear of opening while Door is moving.2DoNotallow children to play with Wireless Keypad.4During programming, the Door Opener could begin to run, so stay away from the moving Door and its parts. To keepthe Door from moving, close the Door and disconnect it from the Opener by pulling the Emergency Release Cord. WARNINGBASICPROGRAMMING FORONEDOCODEDODGER®OROPENERSIf Safety Reverse does not work properly:1Close Door and disconnect the opener using Emergency Release Cord.2 Do not use Door Opener, Remote , or Wireless Keypad.3Refer to Door and Door Opener Owner’s Manuals before attempting any repairs.DOCODEDODGER®OROPMULTIPLEENERSPROGRAMMING FORPROGRAMSETPROGRAMSETThis page is for CodeDodger® 2 Only:If you have an CodeDodger® 1 openeror openers, go to the reverse side of this instruction.CODEDODGER® 2 MODE OF TRANSMISSION CODEDODGER® 1PROGRAMMINGINSTRUCTIONPROG1470258369ABC DEFGHIPQRS TUV WXYZJKL MNOSTEP 2:PROGRAMMINGMULTIPLEDOOROPENERSWait until Keypad Backlight turns off (approximately 30 seconds).PROGRAMSET1 2 3On your Wireless Keypad: On your opener’s power head:sSelect first opener and press and hold until both LEDs turn BLUE. sPress and release again. LEDs should blink PURPLE.sEnter PIN and press . sPress the number that you have picked for this door or . sPress 3 times — opener will run. sRepeat procedure below dotted line for remaining openers.s Release button. Only round LED will be BLUE.PROGRAMSETAll Door Openers will use the same PIN.On your keypad:sEnter your PIN and press .sPress again.sPress the number of Doors (total) you wishto control ( or ).sssssssssssssssssssssssssssssssssPress .2 3 PROGRAMPROGRAMPROGRAMDecide which Door will be Door #1, #2 and #3.
A Moving Door can cause serious injury or death.1Keep3Wall Control should be mounted within sight of door, at least 5 feet above floor and clear of moving parts. people clear of opening while Door is moving.2 Do Not allow children to play with Wireless Keypad.4During programming, the Door Opener could begin to run, so stay away from the moving Door and its parts. To keep the Door from moving, close the Door and disconnect it from the Opener by pulling the Emergency Release Cord. WARNINGSTEP3: OPERATINGONEDOOROPENERTo open or close the Garage Door.sEnter your PIN.sPress .STEP2:Find the Learn Code Button and Learn Code Indicator LED on your door opener.–– If your Door Opener does nothave an Antenna,you have an External Receiver.The External Receiver cover must be removed to access the Learn Code Button and Indicator LED.sPress the Learn Code Button.–Learn Code Indicator LED (on Opener) will blink.sEnter your PIN and press on Keypad.– Learn Code Indicator LED stays on.sPress again.– Learn Code Indicator LED turns off.BASICPROGRAMMING FORONEDOCODEDODGER®OROPENERDOCODEDODGER®OROPENER Decide which Door will be Door #1, #2 and #3.sEnter your PIN and press on Keypad.sPress thesPress and hold the for 2 seconds. number you have picked for thisDoor Opener ( or or ).sPress 3 times.– Opener will run.Repeat procedure below dotted line for each opener.(Each Door Opener must be programmed to receive thesignal from the Wireless Keypad).STEP3: OPERATINGMULTIPLEDOOROPENERSTo open or close a Door after programming is complete.sEnter your PIN.sPress .sPress Door Opener number ( or or ).Proceed to Section 3 - Mounting Instructions.PROGRAMMING FOR 2OR 3FOR CONVENIENCEProgram Keypad BEFORE mounting.SECTION1SECTION2FOR CONVENIENCEProgram Keypad BEFORE mounting.STEP2:All Door Openers will use the same PIN.On your keypad:sEnter your PIN and press .sPress again.sPress the number of Doors (total) you wishto control ( or ).sssssssssssssssssssssssssssssssssPress .If Safety Reverse does not work properly:1Close Door and disconnect the opener using Emergency Release Cord.2 Do not use Door Opener, Remote , or Wireless Keypad.3Refer to Door and Door Opener Owner’s Manuals before attempting any repairs.Proceed to Section 3 - Mounting Instructions.NOTEsIf the Door does not move,check the red LED on Keypad. If the LED is blinking rapidly, the PIN was entered incorrectly. After the LED stops blinking,re-enteryour PIN and try again.sAny Keypad Button will control the Door for 30 seconds after the Door starts moving.sRapid blinking of the red LED indicates an error. After a few seconds the LED will turn off. Start over.NOTEsIf the Door does not move,check the red LED on Keypad. If the LED is blinking rapidly, the PIN was entered incorrectly. After the LED stops blinking,re-enteryour PIN and try again.sAny Keypad Button will control the Door for 30 seconds after the Door starts moving.sRapid blinking of the red LED indicates an error. After a few seconds the LED will turn off. Start over.Wait until Keypad Backlight turns off (approximately 30 seconds).Wait until Keypad Backlight turns off (approximately 30 seconds).2 31 2 31 2 3sPress again.– Opener will run.STEP1: CREATINGYOURWIRELESSKEYPADPIN(PERSONALIDENTIFICATIONNUMBER)sPress in order .sPress . sEnter your PIN (3 to 8 characters).ssClose keypad cover and wait 30 seconds.Press . 3 5 7sPress in order .sPress . sEnter your PIN (3 to 8 characters).ssClose keypad cover and wait 30 seconds.Press . 3 5 7STEP1: CREATINGYOURWIRELESSKEYPADPIN(PERSONALIDENTIFICATIONNUMBER)TEACHING PIN TO SINGLE OPENERPROGRAMMINGMULTIPLEDOOROPENERSMOUNTING INSTRUCTIONSThe Keypad must be mounted in sight of the Door(s), at least 5 feet above the ground and clear of any moving Door parts.AMount Keypad.(Mounting screws located inside Battery Compartment.)sRemove Battery Cover (See Figure 3).sDrill a 1/16”pilot hole for the top mounting screw.sInstall a screw into the drilled hole,leaving a 1/8" gap between the screw headand the wall. (See Figure 2.)sHook the Keypad over the screw.sMark and drill pilot hole and fasten bottom screw.sReinstall Battery Cover.SECTION3ADDITIONAL OPERATIONSSECTION4USING ATEMPORARYPIN A temporary PIN allows temporary access to your home byIf you have forgotten your PIN or you fear it may have fallen into unauthorized hands, you must erase the old programming.repair persons, meter readers, etc.if you so desire.NOTEDO NOT reprogram the Door Opener(s).sTemporary PIN remains active only until the next time nyour ormal PIN is entered.FORGOTYOURPIN (RESETTING WIRELESS KEYPAD)CHANGINGYOURPINEnter your current PIN and press .Wallscrew head gapFigure 2CHANGINGBATTERYssssssssssEnter your current PIN and press 3 times.Press and hold . Release both buttons. You must now start from the beginning and reprogram your Wireless Keypad. While holding press and hold for 5 seconds.Enter your NEW PIN and press .Enter your TEMPORARY PIN and press .If the Keypad backlight does not come on, this indicates the need to replace the batteries.Press in on the front of the battery cover and slide it down off of the Keypad. Remove used batteries and replace with "AAA." Make sure the batteries are inserted properly using the polarity markings. CODEDODGER® 1 MODE of CODE TRANSMISSIONRed IndicatorLEDLearn Code ButtonLocatedon OpenerHousingPROGRAMPROGRAMPROGRAM PROGRAM PROGRAMPROGRAMPROGRAMPROGRAMsPress the Learn Code Button. (See Step 2 in Section 1.) PROGRAMPROGRAMPROGRAMPROGRAMPROGRAMPROGRAMCovers available in:sTan - P/N 37227TsAlmond - P/N 37227UsGray- P/N 37227SsWhite- - P/N 37227RIf your Door Opener has a blackantenna wire and the serial number does not start with 10 or higher, the Learn Code Button and Indicator LED are located near the antenna. (The light lens may need to beopened. If you use an external receiver, it may need to be openedto access the Learn Code Button and Indicator LED. sNo programming is lost during replacement of batteries. To Operate CodeDodger® 1 Openers: This Wireless Keypad comes from the factory as an CodeDodger® 2 unit. In order to initially program an opener or openers which are CodeDodger®1, you must switch the Keypad to CodeDodger®1 mode.sAfter entering your PIN, Press .sssPress and hold for two seconds and theGREEN LED above the number keys will turn RED. PROGRAM Once all your doors have been programmed, there is no need to switch back and forth between CodeDodger® modes. The Keypad will automatically remember the mode of each opener.Close the Keypad cover.Follow the instructions on this page for programming your CodeDodger® 1 opener(s).For answers to questions,call 1-800-275-6187 , or visitwww.overheaddoor.comOverhead Door Corp., 2501 S State Hwy.,Suite 200, Lewisville, TX75067. Additional products can be ordered through localOverhead Door® Professional Dealers. To locate a dealer near you, call 1-800-929-DOOR.2YHUKHDG'RRU&RUSRUDWLRQ+ AAA -+ AAA -Figure 3PressherePolaritymarkingsBatteryCover

Navigation menu