The Genie a Division of Overhead Door GL2T Remote Control Transmitter For Garage Door Opener Operation User Manual Exhibit D Users Manual per 2 1033 b3
The Genie Company a Division of Overhead Door Corporation Remote Control Transmitter For Garage Door Opener Operation Exhibit D Users Manual per 2 1033 b3
Exhibit D Users Manual per 2 1033 b3
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 3486425 |
| Application ID | leNhPpuIduNKuODAKBEFIg== |
| Document Description | Exhibit D Users Manual per 2 1033 b3 |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 83.16kB (1039518 bits) |
| Date Submitted | 2017-07-28 00:00:00 |
| Date Available | 2017-07-28 00:00:00 |
| Creation Date | 2016-11-14 10:40:45 |
| Producing Software | Adobe PDF Library 10.0.1 |
| Document Lastmod | 2017-06-29 13:23:10 |
| Document Title | Exhibit D Users Manual per 2 1033 b3 |
| Document Creator | Adobe InDesign CS6 (Windows) |
LED Flashlight Remote WARNING MOVING DOOR CAN CAUSE SERIOUS INJURY OR DEATH. • DO NOT install transmitter unless the door operator’s safety device works as required by the door operator’s manual. • Wall Console must be mounted in sight of door, at least 5 feet above floor and clear of moving door parts. • Keep people clear of opening while door is moving. • DO NOT allow children to play with the transmitter or door operator. If safety reverse does not work properly: • Close door then disconnect opener using the manual release handle. • DO NOT use transmitter or door operator. • Refer to Door and Door Opener Owner’s Manuals before attempting any repairs. -ORGenie® openers and external receivers manufactured between 1995 to 2011 Place operator into programming mode: 1. Press & release Learn Code button once. The red LED will begin to flash. RADIO SIGNAL RADIO SIGNAL DÉMÉNAGEMENT PORTE PEUT CAUSER DES BLESSURES GRAVES OU LA MORT. Putting Opener into Programming Mode SET LEARN MANUAL LIMIT FORCE SET CODE CLOSE LEARN CODE AVERTISSEMENT • NE PAS installer le transmetteur à moins que le dispositif de sécurité de l’opérateur de porte ne fonctionne comme l’exige le manuel d’utilisation de la porte. • Console murale doit être monté en vue de la porte d’au moins 5 pieds au-dessus-de-chaussée et claire des pièces mobiles de la porte. • Garder les personnes clair de l’ouverture lorsque la porte est en mouvement. • Ne pas laisser les enfants jouer le premier match à distance ou la porte. Si la sécurité inverse ne fonctionne pas correctement: • Fermer la porte, puis débranchez moteur à l’aide de la poignée de déverrouillage manuel. • Ne pas utiliser d’ouverture à distance ou la porte. • Reportez-vous à la porte et ouvre-porte de propriétaires manuels avant de tenter toute réparation. LEARN OPEN or LEARN CODE CODE RADIO SIGNAL LEARN CODE Proceed to step 2 Programming a Remote to the Opener NOTE: Once in programming mode, you will have approximately 30 seconds to perform this step. Note: While programing remote buttons, stand at least 5 feet away from the opener. This ensures you have proper communication between the remote and the opener. PROGRAM Flashlight Button New Genie® Openers SET PRGM PROGRAM Remote Buttons SET SET TYPE 2 TYPE 3 There are 3 types of programming button pads. Type 1 is shown in these steps. All buttons perform the same function and programming is the same for all types shown above. Place operator into programming mode: TYPE 1-2-3 1. Press and hold the program button until the round LED turns blue, then release. PROGRAM PROGRAM SET The round LED will go out and the long LED will begin flashing purple. - OR - TYPE 1 2. SET PROGRAM SET 2. SET Slowly press and release the remote button of your choice two times. The opener LEDs will flash and go off, indicating you have successfully programmed your remote. RADIO SIGNAL LEARN CODE Press and release the same button a third time and door will open or close. NOTE: It is possible to press the remote button too quickly or lightly. If the LEDs do not go OFF, press the remote button several more times to achieve confirmation. PROGRAM 1. Proceed to step 2 or see alternate programming (top right) ar dp Nee mb t nu er 111222501234, 11/2016 3 Lost or Stolen Remote/Erasing all Remotes Replace the Battery This pertains to all button pad TYPES shown in section 1 Replace remote battery with 1-AAA battery. New Genie® Openers 1. Press down on top of battery door and slide back off of remote. PROGRAM 1. Press and hold the program button until the round LED turns blue, then release. SET PROGRAM SET 3. Align cover and snap case closed. PROGRAM SET 2. Press and hold the Up(+) Down (-) buttons at the same time, until the both LEDs flash blue and go OFF. 2. Match battery polarity symbols inside battery housing and replace battery. Genie® openers and external receivers manufactured between 1995 to 2011. • To erase all remote devices from all other types of Genie® openers, Press and hold the Learn Code Button until the LED stops blinking. RADIO SIGNAL LEARN CODE AAA -OR- RADIO SIGNAL LEARN CODE Start at section 1 to reprogram your remotes. NOTE: Clearing remote control memory from the power head will clear ALL programmed remotes and wireless keypads. Your opener will no longer recognize any signal from any remote device, including a missing remote device. Using the LED Flashlight Press the LED Flashlight button once. LED Flashlight will operate until button is pressed again or when 4 minutes have passed. After 4 minutes the LED will flash indicating that light will turn off automatically. For additional help or information, please visit our website at www.GenieCompany.com, contact our Customer Care group at 1-800-35-Genie, or write to us directly at: GMI Holdings INC. d/b/a The Genie Company One Door Drive, PO Box 67 Mount Hope, Ohio 44660 FCC Part 15.21 Statement: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC / IC Statement: This device complies with FCC Part 15 and Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. ©2016 GMI Holdings, Inc. DBA The Genie Company
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes XMP Toolkit : Adobe XMP Core 5.6-c015 84.159810, 2016/09/10-02:41:30 Create Date : 2016:11:14 10:40:45-05:00 Metadata Date : 2017:06:29 13:23:10-05:00 Modify Date : 2017:06:29 13:23:10-05:00 Creator Tool : Adobe InDesign CS6 (Windows) Instance ID : uuid:986daef5-4317-4839-ae79-c3f1524a5635 Original Document ID : xmp.did:5D35DCE40F96E6118930B46E7F3D1B7F Document ID : xmp.id:CB88C5A680AAE61183B9C2BF6B35F9CF Rendition Class : proof:pdf History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CS6 (Windows) History Changed : / History When : 2016:11:14 10:40:45-05:00 Derived From Instance ID : xmp.iid:CA88C5A680AAE61183B9C2BF6B35F9CF Derived From Document ID : xmp.did:5D35DCE40F96E6118930B46E7F3D1B7F Derived From Original Document ID: xmp.did:5D35DCE40F96E6118930B46E7F3D1B7F Derived From Rendition Class : default Format : application/pdf Producer : Adobe PDF Library 10.0.1 Trapped : False Page Count : 2 Creator : Adobe InDesign CS6 (Windows)EXIF Metadata provided by EXIF.tools