Thomson 2-8021A 5.8 GHz Single-Line FHSS Cordless Telephone User Manual users manual 1

Thomson Inc. 5.8 GHz Single-Line FHSS Cordless Telephone users manual 1

users manual 1

REGNRIPROGABC DEFGHI JKL MNOPQRS TUV WXYZEXIT OPER PAUSEIntroductIonCAUTION: When using telephone equipment, there are basic safety instructions that should always be followed. Refer to the IMPORTANT SAFETY INSTRUCTIONS provided with this product and save them for future reference.IMPORTANT: Because cordless phones operate on electricity, you should have at least one phone in your home that isn’t cordless, in case the power in your home goes out.Before You BegInParts Checklist (for 28021xx1 model)Make sure your package includes the items shown here.Model 28021 SerIeS5.8 gHz cordleSS HandSet SpeakerpHone SYSteM uSer’S guIdeequIpMent approval InforMatIonYour telephone equipment is approved for connection to the Public Switched Telephone Network and is in compliance with parts 15 and 68, FCC Rules and Regulations and the Technical Requirements for Telephone Terminal Equipment published by ACTA.1 Notification to the Local Telephone CompanyOn the bottom of this equipment is a label indicating, among other information, the US number and Ringer Equivalence Number (REN) for the equipment. You must, upon request, provide this information to your telephone company.The REN is useful in determining the number of devices you may connect to your telephone line and still have all of these devices ring when your telephone number is called. In most (but not all) areas, the sum of the RENs of all devices connected to one line should not exceed 5. To be certain of the number of devices you may connect to your line as determined by the REN, you should contact your local telephone company.A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. See installation instructions for details.Notes • This equipment may not be used on coin service provided by the telephone company.• Party lines are subject to state tariffs, and therefore, you may not be able to use your own telephone equipment if you are on a party line. Check with your local telephone company.• Notice must be given to the telephone company upon permanent disconnection of your telephone from your line.• If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this product does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualied installer.US Number is located on the cabinet bottom.REN Number is located on the cabinet bottom.2 Rights of the Telephone Company Should your equipment cause trouble on y our line which may harm the telephone network, the telephone company shall, where practicable, notify you that temporary discontinuance of service may be required. Where prior notice is not practicable and the circumstances warrant such action, the telephone company may temporarily discontinue service immediately. In case of such temporary discontinuance, the telephone company must: (1) promptly notify you of such temporary discontinuance; (2) afford you the opportunity to correct the situation; and (3) inform you of your right to bring a complaint to the Commission pursuant to procedures set forth in Subpart E of Part 68, FCC Rules and Regulations.4. Insert the battery pack.5. Close the battery compartment by pushing the door up until it snaps into place.Base Station1. Choose an area near an electrical outlet and a telephone wall jack (RJ11C), and place your cordless telephone on a level surface, such as a desktop or tabletop, or you may mount it on the wall.2. Plug one end of the telephone line cord into the TEL LINE jack on the bottom of the base and the other end into a modular jack.Programming FunctionsThe system uses a menu structure to give you access to all of the built-in features. You may program the following items in main menu: Room Monitor and Handset Setup.Room Monitor (applicable only with additional handsets)1. Make sure your phone is OFF (not in talk mode).2. Press the MUTE/PROG button to go to the main menu.3. Press CALLER ID-VOLUME ( 6 or 5) button to scroll to ROOM MONITOR.4. Press MUTE/PROG button to enter ROOM MONITOR menu, ROOM MONITOR EXTENSION? shows in the display.Area CodeFrom the Handset Setup Menu:1. Press the CALLER ID-VOLUME ( 6 or 5) button to scroll to the AREA CODE sub-menu.2. Press MUTE/PROG button to enter the menu. SET AREA CODE - - - shows in the display. The default setting is " - - -".3. Use the touch-tone pad to enter your 3-digit area code.4. Press the MUTE/PROG button to conrm. You will hear a conrmation tone and the new area code shows in the display.NOTE: To restore the default setting to - - -, press and release DELETE when SET AREA CODE shows in the display.RegistrationYour packaged handset(s) are pre-registered and ready to use. It is not recommended that a handset be registered again unless absolutely necessary.From the Handset Setup Menu:1. Press the CALLER ID-VOLUME ( 6 or 5) button to scroll to the REGISTRATION sub-menu.2. Press the MUTE/PROG button to enter the menu. REGISTRATION 1YES 42NO - - - shows in the display The default setting is "2NO".3. Use the touch-tone pad to select 1 for YES or 2 for NO. Or use the CALLER ID-VOLUME ( 6 or 5 button to scroll to 1YES or 2NO.4. If you select 1YES, press the MUTE/PROG button to conrm your selection. HOLD BASE PAGE WAIT FOR BEEP shows in the display. (Your handset should be held near the base during registration process.)5. Press and hold the page button on the base unit until you hear a tone at the handset. HANDSET X REGISTERED shows in the handset display, where X is the handset number. You may now rename your handset. (Refer to Step 3 & 4 of Handset Name Section)De-RegistrationDe-registration cancels registration. During the de-registration process, keep the handset near the base.From the Handset Setup Menu:1. Press the CALLER ID-VOLUME ( 6 or 5) button to scroll to the DEREGISTRATION sub-menu.2. Press the MUTE/PROG button to enter the menu. REGISTRATION 1YES 42NO - - - shows in the display The default setting is "2NO".3. Use the touch-tone pad to select 1 for YES or 2 for NO. Or use the CALLER ID-VOLUME ( 6 or 5) button to scroll to 1YES or 2NO.WARNING: It is not recommended that a handset be de-registered unless absolutely necessary because once a handset is de-registered, that handset’s telephone features cannot be used until the handset is re-registered.4. Select NO, if you do not want to de-register.5. If you select 1YES, press the MUTE/PROG button and MOVE NEAR TO BASE displays for 2 seconds, then CONFIRM? 1YES 2NO appears in the display.6. Press the touch-tone pad to select 1YES or 2NO, or use the CALLER ID-VOLUME ( 6 or 5) button to scroll to 1YES or 2NO.7. If you select YES, press the MUTE/PROG button to conrm. You will hear a conrmation tone. Then HANDSET X DEREGISTERED shows in the display to conrm the handset is deregistered.NOTE: When you complete the de-registration process, HANDSET NEEDS REGISTRATION shows in the display. To use the handset, you MUST re-register the handset using the Registration process.Global De-registration (applicable only with additional handsets)If one or more handsets becomes lost, you should de-register all handsets to ensure proper system operation. Follow the steps below to de-register all handsets at the same time.WARNING: It is not recommended that a handset be de-registered unless absolutely necessary because once a handset is de-registered, that handset’s telephone features cannot be used until the handset is re-registered.1. Press and hold the page button on the base until the CHARGE/IN USE indicator on the base ashes.2. Press and hold the page button on the base again until the CHARGE/IN USE indicator on the base ashes rapidly.3. Press and release the page button on the base once. All handsets are de-registered and HANDSET NEEDS REGISTRATION shows in the display.Default SettingAs you become familiar with this system, you may prefer to use the system’s original settings. Follow the steps below to return to the factory default settings.From the Handset Setup Menu:1. Press the CALLER ID-VOLUME ( 6 or 5) button to scroll to the DEFAULT SETTING sub-menu. 2. Press the MUTE/PROG button to enter the menu. DEFAULT SETTING 1YES 2NO shows in the display. The default setting is "2NO".3. Use the touch-tone pad to select 1YES or 2NO, or use the CALLER ID-VOLUME ( 6 or 5) button to move the cursor to 1YES or 2NO. ATLINKS USA, Inc.10330 North Meridian StreetIndianapolis, IN 46290© 2006 ATLINKS USA, Inc. Trademark(s) ® RegisteredMarca(s) Registrada(s)Model 28021 00007425 (Rev. 0 Dom E) 05-50 Printed in ChinaModular telephone line jackWall plateSEE MARKING ON BOTTOM / BACK OF PRODUCTRISK OF ELECTRIC SHOCK DO NOT OPENWARNING: TOPREVENT FIRE ORELECTRICAL SHOCKHAZARD, DO NOTEXPOSE THISPRODUCT TO RAINOR MOISTURE.THE LIGHTNINGFLASH AND ARROWHEAD WITHIN THETRIANGLE IS AWARNING SIGNALERTING YOU OF“DANGEROUSVOLTAGE” INSIDETHE PRODUCT.CAUTION: TO REDUCE THERISK OF ELECTRIC SHOCK, DONOT REMOVE COVER (ORBACK). NO USERSERVICEABLE PARTS INSIDE.REFER SERVICING TOQUALIFIED SERVICEPERSONNEL.THE EXCLAMATIONPOINT WITHIN THETRIANGLE IS AWARNING SIGNALERTING YOU OFIMPORTANTINSTRUCTIONSACCOMPANYINGTHE PRODUCT.CAUTION:BaseHandsetBeltclipTelephone line cordAC power adaptorHandset battery packBattery compartment coverNOTE: If you choose YES all the settings in the programmable menu are returned to factory default setting.4. Press the MUTE/PROG button to save your selection. You will hear a conrmation tone. Telephone OperationCharge/In Use IndicatorThe phone is ON when the LED indicator on the handset and the CHARGE/IN USE indicator on the base is lit. The handset and base indicators ash when you receive a call.Speakerphone Operation.NOTE: If you are using the speakerphone, remain close to handset so the party you are speaking to can hear you. If you are using the handset and want to switch to the speakerphone, press the SPEAKER button, press SPEAKER again to end conversation. If you are using the speakerphone and want to switch to the handset, press the TALK/CALL BACK button, press TALK/CALL BACK again to end conversation. Making a Call1. Press the TALK/CALL BACK or SPEAKER button. Dial the desired number. - OR - Dial the number rst, then press the TALK/CALL BACK or SPEAKER button. - OR - Press the CALLER ID-VOLUME ( 6 or 5) button to select the desired record, then press the TALK/CALL BACK or SPEAKER button2. When nished, press the TALK/CALL BACK or SPEAKER button to hang up.NOTE: You may enter up to 32 pre-dial digits.NOTE: If you want to delete the pre-dial number you entered, press the DELETE button until all of the digits are erased. Answering Calls1. When the phone rings, press the SPEAKER button on the handset - OR - pick up the handset and press the TALK/CALL BACK button. 2. When nished, press SPEAKER or TALK/CALL BACK to hang up.NOTE: Adjust the handset volume by pressing the CALLER ID-VOLUME ( 6 or 5) button during a call.Call TimerAfter you press the TALK/CALL BACK button on the handset, the built-in call timer shows on the display and counts the length of time of the call in minutes and seconds.Auto StandbyIf you place the handset in the cradle while the handset is off the hook (during a call), the call is automatically disconnected.Ringer HI/LOW/OFF (Shortcut)There are two ways to set the ringer to HI/LOW/OFF. One is the traditional way as described in the Programming Functions; Handset Setup; Ringer Volume menus. The other one is this short cut to ringer menu.1. Make sure the phone is OFF (not in talk mode).2. Press the #PAUSE/RINGER button to display 1HI 2LOW 3OFF. 3. Use the touch tone pad on the handset to select 1, 2 or 3, or use the CALLER ID-VOLUME ( 6 or 5) button to scroll to your selection. HI is the default setting.4. Press #PAUSE/RINGER button again to save and display the new selection for a few seconds.Flash/Call WaitingIf you subscribe to the combined Call Waiting Caller ID service from your local telephone company, you will receive Caller ID information (if available) on Call Waiting calls. During a phone call, you will hear a beep to indicate another call is waiting on the line and Caller ID information for the waiting call shows on the handset display.• To connect to the waiting call, press the FLASH button on the handset, and your original call is put on hold.• To switch between the two calls, press the FLASH button.TIP: Do not press the TALK/CALL BACK button on the handset to activate a custom calling service, such as call waiting, or call will disconnect.The telephone company may make changes in its communications facilities, equipment, operations or procedures where such action is required in the operation of its business and not inconsistent with FCC Rules and Regulations. If these changes are expected to affect the use or performance of your telephone equipment, the telephone company must give you adequate notice, in writing, to allow you to maintain uninterrupted service.Interference InforMatIonThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference; and (2) This device must accept any interference received, including interference that may cause undesired operation.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna (that is, the antenna for radio or television that is “receiving” the interference).• Reorient or relocate and increase the separation between the telecommunications equipment and receiving antenna.• Connect the telecommunications equipment into an outlet on a circuit different from that to which the receiving antenna is connected.If these measures do not eliminate the interference, please consult your dealer or an experienced radio/television technician for additional suggestions. Also, the Federal Communications Commission has prepared a helpful booklet, “How To Identify and Resolve Radio/TV Interference Problems.” This booklet is available from the U.S. Government Printing Ofce, Washington, D.C. 20402. Please specify stock number 004-000-00345-4 when ordering copies.HearIng aId coMpatIBIlItY (Hac)This telephone system meets FCC standards for Hearing Aid Compatibility.lIcenSIngLicensed under US Patent 6,427,009.fcc rf radIatIon expoSure StateMentThis equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.”For body worn operation, this phone has been tested and meets the FCC RF exposure guidelines when used with the belt clip supplied with this product. Use of other accessories may not ensure compliance with FCC RF exposure guidelines.displayTALK/CALL BACK (button)CALLER ID-VOLUME down (button) CALLER ID-VOLUME up button)DELETE(button)REDIAL (button)*EXIT (button) #PAUSE/RINGER (button)FLASH(button)FORMAT/CONF (format/conference button)MEMORY (button)SPEAKER(button)MUTE/PROG (mute/program button)Your new GE telephone system is EXPANDABLE up to a total of 4 handsets (by purchase of optional Model 28001 handset with charge cradle)Wall mount bracketFor Model 28021xx3 there will be TWO additional handsets, charge cradles, belt clips, battery packs and covers than shown above.For Model 28021xx4 there will be THREE additional handsets, charge cradles, belt clips, battery packs and covers than shown above.Telephone Jack RequirementsTo use this phone, you need an RJ11C type modular telephone jack, which might look like the one pictured here, installed in your home. If you don’t have a modular jack, call your local phone company to nd out how to get one installed.InStallatIon Digital Security SystemYour cordless phone uses a digital security system to protect against false ringing, unauthorized access, and charges to your phone line.INSTALLATION NOTE: Some cordless telephones operate at frequencies that may cause or receive interference with nearby TVs, microwave ovens, and VCRs. To minimize or prevent such interference, the base of the cordless telephone should not be placed near or on top of a TV, microwave ovens, or VCR. If such interference continues, move the cordless telephone farther away from these appliances.Certain other communications devices may also use the 5.8 GHz frequency for communication, and, if not properly set, these devices may interfere with each other and/or your new telephone. If you are concerned with interference, please refer to the owner’s manual for these devices on how to properly set channels to avoid interference. Typical devices that may use the 5.8 GHz frequency for communication include wireless audio/video senders, wireless computer networks, multi-handset cordless telephone systems, and some long-range cordless telephone systems.Important Installation Guidelines• Avoid sources of noise and heat, such as motors, uorescent lighting, microwave ovens, heating appliances and direct sunlight.• Avoid areas of excessive dust, moisture and low temperature.• Avoid other cordless telephones or personal computers.• Never install telephone wiring during a lightning storm.• Never install telephone jacks in wet locations unless the jack is specically designed for wet locations.• Never touch non-insulated telephone wires or terminals, unless the telephone line has been disconnected at the network interface.• Use caution when installing or modifying telephone lines.HandSet laYoutINTERCOM (button)InStallIng tHe pHoneInstalling the Handset BatteryNOTE: You must connect the handset battery before use.CAUTION: To reduce the risk of fire or personal injury, use only the ATLINKS USA, Inc. Nickel-metal Hydride battery model 5-2660, which is compatible with this unit.1. Locate battery and battery door which are packaged together inside a plastic bag and are separate from the handset.2. Locate the battery compartment on the back of the handset.3. Plug the battery pack cord into the jack inside the compartment.NOTE: To ensure proper battery installation, the connector is keyed and can be inserted only one way.black wirered wirebatterypackPRESS DOWNFIRMLY3. Plug the AC power converter into the electrical outlet and the DC connector into the jack on the bottom of the base.4. Place the handset in the base cradle. The charge/in use indicator turns on, verifying the battery is charging.5. Allow the phone to charge for 16 hours prior to rst use. If you don’t properly charge the phone, battery performance is compromised.CAUTION: Use only the ATLINKS USA, Inc. 5-2512 power converter that came with this unit. Using other power converters may damage the unit.Wall Mounting1. Turn the base over.2. Attach the wall mounting pedestal by rst inserting the tabs on the open edge of the pedestal into the slots on the lower portion of the bottom of the base. Then push down and snap the pedestal into place.3. Slip the mounting holes (on the back of the base) over the wall plate posts, and slide the unit down into place. (Wall plate not included.)NOTE : If desired, gather the extra telephone line and power adaptor cord and store inside the wall mounting bracket.prograMMIng tHe telepHoneStandby ScreenThe handset displays the handset number and user name.Ringer ToneYou may choose from ten different ringer tones and ten different melodies.From the Handset Setup Menu:1. Press the CALLER ID-VOLUME ( 6 or 5) button to scroll to the RINGER TONE sub-menu.2. Press MUTE/PROG button to enter the menu. SET RINGER TONE 01 shows in the display. The default setting is "01".3. Use the CALLER ID-VOLUME ( 6 or 5) button to scroll to the desired setting (1 through 20). You will hear a sample of the ringer tone/melody you select.4. Press the MUTE/PROG button to save your selection. You will hear a conrmation tone and the selected ringer tone shows in the display.NOTE: You must have the Ringer Volume set to ON for ring tone to signal an incoming call. Ringer VolumeFrom the Handset Setup Menu:1. Press the CALLER ID-VOLUME ( 6 or 5) button to scroll to the RINGER VOLUME sub-menu.2. Press MUTE/PROG button to enter the menu. SET RINGER 41HI 2LOW 3OFF shows in the display. The default setting is "HI".3. Use the touch tone pad on the handset to select 1, 2 or 3, or use the CALLER ID-VOLUME ( 6 or 5) button to scroll to your selection. 4. Press the MUTE/PROG button to save your selection. You will hear a conrmation tone and the new volume setting shows in the display.NOTE: If you turn the ringer OFF, the ringer off icon shows in the display.VIP MelodyThis features allow you to assign a specic melody to someone you want to get your attention when the person calls. When a VIP melody is assigned and that person calls, the unit rings the normal ring for the rst ring and then follows with VIP melody ring. You may choose from ten different polyphonic melodies and may store up to 10 VIP records.NOTE: This feature ONLY works when the following conditions are met.1. You have subscribed to Caller ID.2. You have your Caller ID record previously transferred to the memory. (Refer to Storing CID Records in Internal Memory). NO USER MEMORY will show in the display to remind the user to do CID record transfer first.Storing VIP MelodyFrom the Handset Setup Menu:1. Press the CALLER ID-VOLUME ( 6 or 5) button to scroll to VIP MELODY sub-menu. 2. Press MUTE/PROG button to select VIP MELODY feature and then display VIP 1 record. - If VIP1 does NOT contain any specic number/records, it will display **EMPTY**.3. Press CALLER ID-VOLUME ( 6 or 5) button to select the specic VIP melody memory location (10 VIP locations) that does not contain any record.4. Press MUTE/PROG button to display SELECT MEMORY.NOTE: If the memory location does not contain any CID memory records and you are trying to mark a specific record as VIP MELODY, then SELECT MEMORY will not be displayed. Instead, NO USER MEMORY will display in prompt to alert the user.5. Press CALLER ID-VOLUME ( 6 or 5) button to view the records from memory to be selected as VIP.6. Press MUTE/PROG button to conrm and then display VIP MELODY 01 to wait for the melody tone selection.7. Press CALLER ID-VOLUME ( 6 or 5) button to select from melody 01 to melody 10 (a testing tone is generated while making melody selection)8. Press MUTE/PROG button to conrm. NOTE: If the desired number/record was previously stored in any one of the ten VIP melody records, DUPLICATE NUMBER shows in the display.Changing a Stored VIP Melody RecordUse the Storing VIP Melody procedure to change the number of a selected record and replace the old phone number with new phone number.When REPLACE VIP# ? shows in the display, you must press MUTE/PROG button on the handset to conrm replacement.Reviewing And Deleting Stored VIP Melody Record1. Press the CALLER ID-VOLUME ( 6 or 5) button to scroll to VIP MELODY sub-menu. 2. Press MUTE/PROG button to select VIP MELODY feature and then display VIP 1 record. 3. Use the CALLER ID-VOLUME ( 6 or 5) button to scroll to the desired VIP Melody Record.4. If you want to delete the information, press the DELETE button on the handset while the entry displays. The display show DELETE VIP# ?.5. Press DELETE again to conrm. You will hear a conrmation tone and VIP# DELETED shows in the display.Key ToneFrom the Handset Setup Menu:1. Press the CALLER ID-VOLUME ( 6 or 5) button to scroll to the KEY TONE sub-menu.2. Press MUTE/PROG button to enter the menu. SET KEY TONE 41ON 2 OFF shows in the display. The default setting is “1ON".3. Use the touch tone pad on the handset to select 1 or 2, or use the CALLER ID-VOLUME ( 6 or 5) button to scroll to your selection. 4. Press the MUTE/PROG button to conrm and the key tone setting shows in the display.USER NAMEHANDSET X> ROOM MONITORHANDSET SETUP5. Use the touch tone pad to enter the handset number to be monitored, either 1 or 2.NOTE: When this phone system is expanded (up to 4 handsets by purchase of optional Model 28001 handset with recharge cradle), handsets are named HANDSET 1, HANDSET 2, HANDSET 3 and HANDSET 4 respectively.6. The receiving handset will turn on the microphone and the originating handset will turn on the speakerphone to monitor sound from the receiving handset.NOTE: For room monitoring mode to work, the originating handset must NOT be on the cradle.NOTE: While in room monitoring mode, the handsets will emit an alert tone approximately every 5 seconds if there is an incoming call. You may press the SPEAKER button to quit room monitor and answer the call.NOTE: While in room monitoring mode, the originating handset can be switched to monitor by handset earpiece by pressing the TALK/CALL BACK button once. Switch back to speakerphone by pressing the SPEAKER button once.NOTE: Press the *EXIT button on the handset to exit room monitor mode.Handset Setup1. Make sure your phone is OFF (not in talk mode).2. Press the MUTE/PROG button to go to the main menu.3. Press CALLER ID-VOLUME ( 6 or 5) button to scroll to HANDSET SETUP.4. Press MUTE/PROG button to conrm and you may program the following items: Language, Handset Name, Ringer Tone, Ringer Volume, VIP Melody, Key Tone, Area Code, Registration, Deregistration and Default Setting.NOTE: During programming, you may press the *EXIT button at any time to exit the sub-menu and return to the menu. LanguageFrom the Handset Setup Menu:1. Press the CALLER ID-VOLUME ( 6 or 5) button to scroll to the SET LANGUAGE sub-menu.2. Press MUTE/PROG button to enter the menu. SET LANGUAGE 41ENG 2FRA 3ESP shows in the display. The default setting is "1 ENG".3. Use the touch tone pad on the handset to select 1ENG, 2FRA, 3ESP, or use the CALLER ID-VOLUME ( 6 or 5) button to scroll to the desired language. 4. Press the MUTE/PROG button to save your selection. You will hear a conrmation tone and the selected language shows in the display.Handset NameFrom the Handset Setup Menu:1. Press the CALLER ID-VOLUME ( 6 or 5) button to scroll to the HANDSET NAME sub-menu.2. Press MUTE/PROG button to enter the menu. HANDSET NAME shows in the display. The default setting is "HANDSET #".3. Use the touch-tone pad to enter a name (up to 15 characters). More than one letter is stored in each of the number keys. For example, to enter Bill Smith, press the 2 key twice for the letter B. Press the 4 key 3 times for the letter I. Press the 5 key 3 times for the letter L. Press the 5 key 3 times for the second letter L, and press the 1 key to insert a space between the rst and last name. Press the 7 key 4 times for the letter S; press the 6 key once for the letter M; press the 4 key 3 times for the letter I; press the 8 key for the letter T; press the 4 key twice for the letter H.NOTE: If you make a mistake, use the DELETE button to backspace and delete one character at a time.4. Press the MUTE/PROG button to save your name. You will hear a conrmation tone and the handset name shows in the display.LED (indicator)Last Number RedialYou may redial a number up to 32 digits long.To quickly redial the last number you dialed:1. Press the TALK/CALL BACK button.2. Press the REDIAL button. -OR-3. Press the REDIAL button rst, then use the CALLER ID-VOLUME ( 6 or 5) button to select the desired redial number. - Press the CALLER ID-VOLUME ( 5) to review the oldest call and scroll toward the most recent calls (higher numbers). - Press the CALLER ID-VOLUME ( 6 ) to review the newest call and scroll to older calls (lower numbers).NOTE: You may choose from three last dialed numbers.4. Press the TALK/CALL BACK button. The number dials automatically.If you get a busy signal and want to keep dialing the number, press the REDIAL button to quickly redial the number.ExitPress the *EXIT button to exit a menu function and return to the standby screen.PageThe page feature helps you locate a misplaced handset. To send and receive pages, all handsets must be registered. If your handset is not registered, follow the instructions in the Registration section of this manual.Handset Paging (applicable only with additional handsets)1. Make sure the phone is OFF (not in talk mode).2. Press and release the INTERCOM button on a handset. PAGING EXTENSION? shows in the display.3. Use the touch-tone pad to enter the handset number you want to page. (1= to page Handset 1, 2=to page handset 2, etc., and 5=to page all handsets)4. To cancel the page, press the *EXIT or INTERCOM button on the receiving handset, or you may press TALK/CALL BACK on the originating handset. Base PagingUse the base-only to page all registered handsets at the same time.1. Press the page button on the base. All handsets beep for two minutes, and PAGING FROM BASE shows on each handset’s display.2. To cancel the page, press the page button on the base, or press the TALK/CALL BACK button or the *EXIT button on each handset.MuteTo have a private, off-line conversation, use the MUTE feature. The party on the telephone line cannot hear you, but you can hear them.1. Press the MUTE/PROG button. The handset display shows MUTE ON. 2. Press the MUTE/PROG button to cancel and return to your phone conversation.Receiver Volume ControlWhen the handset is ON (in talk mode) you may adjust the receiver volume by pressing the CALLER ID-VOLUME ( 6 or 5) button. There are four volume levels to choose from. When the maximum or minimum volume level is reached, the phone beeps twice. VOL 1 is minimum and VOL 4 is maximum.Do Not Disturb (DND) DND allows you to mute the ringer on all handsets. In the standby mode, press the DO NOT DISTURB button on the base. The DND indicator will light and DO NOT DISTURB shows in handset display. To cancel, press the DO NOT DISTURB button again.Intercom Operation (applicable only with additional handsets)The intercom feature allows you to have a conversation with another registered handset without tying up the telephone line, allowing you to still receive incoming calls.Making an Intercom Call1. Make sure the handset is OFF (not in talk mode).2. Press the INTERCOM button on the handset.3. Use the touch-tone pad to select the handset you want to page.NOTE: To cancel page, press the INTERCOM button again or the *EXIT button on the sending handset.REGNRIPROGABC DEFGHI JKL MNOPQRS TUV WXYZEXIT OPER PAUSEFor Model 28021xx2 there will be ONE additional handset, charge cradle, belt clip, battery pack and cover than shown above.PAGE (button)CHARGE/IN USE (indicator)DO NOT DISTURB (button)BaSe laYout

Navigation menu