Tong Lung Metal Industry PL2-BT Electronic BLE Deadbolt User Manual Manual

Tong Lung Metal Industry Co.,Ltd. Electronic BLE Deadbolt Manual

UserManual.wiki >

Tong Lung Metal Industry >

PL2 BT User Manual

Manual

Insert the latch and ensure it is parallel to the door face.Mark the outline of the faceplate, then take out the latch. faceplate to be aligned with the door edge.Note: It is not necessary to chisel the door edge for the faceplate installation if you use the drive-in latch.Chisel 5/32" (4 mm) deep along the outline to allow theInstall LatchYou need to stay thisway up when insertingthe latch.Insert the latch into the door. (Make sure the cross is on thebottom of the latch.)Use 2 wood screws to securelatch.Please do not fully tighten thescrews until lock is completelyinstalled. Install Drive-in LatchDrive the latch into thehole on edge of door.abcd4Mark the Door with TemplateSelect the height and backset as desired on thedoor face; use the TEMPLATE as an indication tomark the centre of the circle on the door face andthe centre of the door edge.25 91011678Install StrikeMachine Screws Qty. 3 Wood Screws Qty. 5Deadbolt Chassis Screws Qty. 2J KLAdjust Thumb Turn PieceInstall Receiver ModuleInsert Batteries Install Keypad AssemblyInstall Inside Mounting PlateIdentify Door HandingTo identify the centre of strike: closethe door to lay the latchbolt againstthe door frame.Mark the centre line on the doorframeexactly opposite the latch hole in thedoor edge.Install cylinder into the deadboltkeypad assembly with tailpiece inhorizontal position inserted throughhub of the latch.the mounting plate.Fix the mounting plate with screws.If outside lock assembly is lopsided,please loosen the screws to adjust itsposition and tighten the screws again.Pass the IC wire through the wire hole ofFace the door from the outside.The door is left-handed if the hinges are on the left side of the door,whereas the door is right-handed if the hinges are on the right side of the door.the interior side of the door, andinsert the tailpiece through thecross-shaped crank of the latchPass the IC wire under the latch to.Install the strike plate into your doorframe and tighten with wood screws.cMounting PlateScrewsDo not use an electric screwdriver during installation.This Manufacturer advises that no lock can provide complete security by itself.This lock may be defeated by forcible or technical means, or evaded by entry elsewhere on the property.No lock can substitute for caution, awareness of your environment, and common sense.Builder's hardware is available in multiple performance grades to suit the application.In order to enhance security and reduce risk, you should consult a qualified locksmith or other security professional.Backset is a distance from door edge to centr ofhole on door face.Adjustable latch fits both backset of 2-3/8" (60 mm)and 2-3/4" (70 mm). eBackset Determination1Drill HolesUsing the marks as a guide to drill a holeØ2-1/8" (54 mm) through the door face for the lockset,then a hole of Ø1" (25.4 mm) for latch.3PACKAGE CONTENTSHARDWARE SCREWS CONTENTS Electronic BLE Touch DeadboltInstallation Guidebfrom door stop and vertically markcentre line of strike.Drill 1" (25.4 mm) hole, 1" (25.4 mm)deep at intersection of horizontal andvertical line of strike.Chisel 5/64" (2 mm) deep along thestrike outline to allow the strike to bealigned with the doorframe.Measure one half of door thicknessRotate the thumb turn piece to the LEFTat 45 degrees for right-handed doors.Rotate the thumb turn piece to the RIGHTat 45 degrees for left-handed doors. Remove the battery cover(push it up first then pull it out).aScrewsWood ScrewConnect the IC wire into the back ofthe receiver module.Ensure that the deadbolt tailpiece isengaged with turn piece, then attachreceiver module to the door withscrew.Use the optional wood screw tosecure the receiver module to wooddoors only.Insert 4 (AA) 1.5 V alkaline batteries and slide the battery cover back onto thereceiver module.Remarks: (1) Alkaline batteries are recommended in orderto stabilize the power supply.If you don't use alkaline, battery performancewill be reduced greatly.(2) All settings will be retained in the memoryeven if the batteries are completed dead.TEMPLATE45mm 40mm 35mm1-3/4" 1-9/16" 1-3/8" Fit here on door edgeFOR BACKSET 70 mm)2-3/4" (FOR BACKSET 60 mm)2-3/8" (51mm2" Mark Ø1" (25.4 mm) hole atcentre of door edge.Ø ( )2-1/8" 54 mmFor right-handeddoorFor left-handeddoorCylinderDescription QuantityPartABCDKeyCylinderDeadbolt Touchpad AssemblyDeadbolt Latch2111EFStrike PlateMounting Plate11Part Description QuantityGHIReceiver AssemblyBattery CoverDrive-in Sleeve1111234567890Brand: EZSETModel: PL2-BTABCDEFGHILKJDetermine if the latch needs to be adjusted to the 2-3/4" (70 mm) backset.To adjust, rotate the latch until it stops.Reverse the direction to return to the 2-3/8" (60 mm) backset.LATCH ADJUSTMENT180°2 3/4" (70 mm)2 3/8" (60 mm)70 mm60 mmCHANGE LATCH FACEDrive-in LatchbaDetermine which latch mounting method will be usedand make necessary adjustments.No adjustment required for square latch face plate.a. Use a flat screwdriver to separate the face plate.b. Snap selected latch face onto back plate.Drive-in InstallationRemove original latch faceplate. Align the as illustratedand snap into the latch case.drive-in sleeveIC wireLeft-handed Right-handedHinge HingeBattery CoveraNote : The thumb turn piece is opposite to the latching side.

Navigation menu