Top Victory Electronics CM990D Color Monitor User Manual D990T

Top Victory Electronics (Taiwan) Co Ltd Color Monitor D990T

users manual

1Your Work Never Looked BetterPlug & Play Drivers for the AOC Spectrum Series Monitors are availableat AOC’s Web Site: www.aoc-europe.com9Elr/9ElrA9Elr+/9ElrA+USER MANUALTABLE OF CONTENTSFOR YOUR SAFETY -------------------------------------------------- 1SAFETY PRECAUTIONS -------------------------------------- 2BEFORE YOU OPERATE THE MONITOR ---------------------- 3FEATURES -------------------------------------------------------- 3PACKING LIST --------------------------------------------------- 3INSTALLATION INSTRUCTIONS --------------------------- 3CONTROLS AND CONNECTORS -------------------------- 4OPERATING INSTRUCTIONS ------------------------------------- 5GENERAL INSTRUCTIONS ---------------------------------- 5HOW TO ADJUST A SETTING ------------------------------ 6ADJUSTING THE PICTURE ---------------------------------- 7POWER MANAGEMENT FEATURE ----------------------- 7PLUG AND PLAY ------------------------------------------------ 9TECHNICAL SUPPORT(FAQ) -------------------------------------10APPENDIX ---------------------------------------------------------------11SPECIFICATIONS ------------------------------------------FACTORY PRESET TIMING TABLE -----------------------13CONNECTOR PIN ASSIGNMENT ------------------------- 13LIMITED THREE-YEAR WARRANTY -----------------------14-15Thank you very much for choosing the AOC Color Monitor.We recommend that you take a few minutes to read carefully through this briefbut comprehensive manual before installing and switching on the monitor.Please keep this manual in a safe place for you future reference.ENGLISHDEUTSCHFRANÇAISESPAÑOLITALIANO11-12
2Before operating the monitor please read this manual thoroughly. This manualshould be retained for future reference.FCC Class B Radio Frequency Interference StatementWARNING: (FOR FCC CERTIFIED MODELS)NOTE: This equipment has been tested and found to comply with the limits for aClass B digital device, pursuant to Part 15 of the FCC Rules. These limits aredesigned to provide reasonable protection against harmful interference in aresidential installation. This equipment generates, uses and can radiate radiofrequency energy, and if not installed and used in accordance with theinstructions, may cause harmful interference to radio communications. However,there is no guarantee that interference will not occur in a particular installation. Ifthis equipment does cause harmful interference to radio or television reception,which can be determined by turning the equipment off and on, the user isencouraged to try to correct the interference by one or more of the followingmeasures:1. Reorient or relocate the receiving antenna.2. Increase the separation between the equipment and receiver.3. Connect the equipment into an outlet on a circuit different from that to whichthe receiver is connected.4. Consult the dealer or an experienced radio/TV technician for help. NOTICE :1. The changes or modifications not expressly approved by the partyresponsible for compliance could void the user's authority to operate theequipment.2. Shielded interface cables and AC power cord, if any, must be used in orderto comply with the emission limits.3. The manufacturer is not responsible for any radio or TV interference causedby unauthorized modification to this equipment. It is the responsibilities ofthe user to correct such interference.As an ENERGY STAR? Partner ,Envision Peripherals Inc. has determined thatthis product meets the ENERGY STAR? guidelines for energy efficiency. WARNING :To prevent fire or shock hazard, do not expose the monitor to rain or moisture.Dangerously high voltages are present inside the monitor. Do not open thecabinet. Refer servicing to qualified personnel only.
3PRECAUTIONS?Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchensink, laundry tub, swimming pool or in a wet basement.?Do not place the monitor on an unstable cart, stand, or table. If the monitorfalls, it can injure a person and cause serious damage to the appliance. Useonly a cart or stand recommended by the manufacturer or sold with themonitor. If you mount the monitor on a wall or shelf, use a mounting kitapproved by the manufacturer and follow the kit instructions.?Slots and openings in the back and bottom of the cabinet are provided forventilation. To ensure reliable operation of the monitor and to protect it fromoverheating, be sure these openings are not blocked or covered. Do notplace the monitor on a bed, sofa, rug, or similar surface. Do not place themonitor near or over a radiator or heat register. Do not place the monitor in abookcase or cabinet unless proper ventilation is provided.?The monitor should be operated only from the type of power source indicatedon the label. If you are not sure of the type of power supplied to your home,consult your dealer or local power company.?The monitor is equipped with a three-pronged grounded plug, a plug with athird (grounding) pin. This plug will fit only into a grounded power outlet as asafety feature. If your outlet does not accommodate the three-wire plug, havean electrician install the correct outlet, or use an adapter to ground theappliance safely. Do not defeat the safety purpose of the grounded plug.?Unplug the unit during a lightning storm or when it will not be used for longperiods of time. This will protect the monitor from damage due to powersurges.?Do not overload power strips and extension cords. Overloading can result infire or electric shock.?Never push any object into the slot on the monitor cabinet. It could shortcircuit parts causing a fire or electric shock. Never spill liquids on the monitor.?Do not attempt to service the monitor yourself; opening or removing coverscan expose you to dangerous voltages and other hazards. Please refer allservicing to qualified service personnel.?To ensure satisfactory operation, use the monitor only with UL listedcomputers which have appropriate configured receptacles marked between100 - 240V AC, Min. 2.5A.
4BEFORE YOU OPERATE THE MONITORFEATURES?48.3cm(19”) Color Monitor?Crisp, Clear Display for Windows?Supports Resolutions up to 1600 ? 1200?Power Management?Ergonomic Design (MPR II Approved)?Space Saving, Compact Case DesignCHECKING THE CONTENTS OF THE MONITOR PACKAGEThe product package should include the following items:1. Monitor2. Owner's Manual3. Power Cord4. Swivel Base5. Audio Cable ( For 9EA/9ElrA only )INSTALLATION INSTRUCTIONSSWIVEL BASETo attach the swivel base to the monitor, do the following:?Carefully turn the monitor on its side or upside down. ( see figure 1 )?Locate the cavities at the bottom front of the monitor.?Insert the pegs on the swivel base into these cavities. Push the swivel baseforward until the swivel base locks in place.?To remove the swivel base, hold the bottom of the swivel base, then push itout.Install Remove Install Remove9E/9Elr 9EA/9ElrAFigure 1 Installing and Removing the Swivel Base
5POWER CORDPower Source:1. Make sure the power cord is the correct type that required in your area.2. This monitor has a universal power supply that allows operation in either100/120V AC or 220/240V AC voltage area ( No user adjustment is required. )3. Connect the power cord into your monitor’s power input socket, and thenplug the other end into a 3-pin AC power outlet. The power cord may beconnected to either a wall power outlet or the power outlet socket on your PC,depending on the type of power cord supplied with your monitor.CONTROLS AND CONNECTORS VIDEO CABLEConnecting the Video Cable: the monitor comes with a built-in video cable.Plug the signal cable?s 15-pin connector into the computer's video port andtighten the two screws on the cable connector. (see figure 2)Caution: Don’t bend the signal cable, otherwise it will break the inner wire.Connecting the Power Cord: Plug the power cord into the monitor's AC powersocket. Then plug the power cord into a grounded AC outlet or UL-approvedpower strip or the power output socket on your PC.Caution: If the AC outlet is not grounded, install the proper grounding adapter(not supplied).Connecting the Audio Cable ( 9EA/9ElrA only ): Plug audio cable between thecomputer multi-media (or sound) card's audio output and monitor's audio input.Connecting the DC Power Cable ( 9E/9Elr only ): Plug DC power cablebetween monitor to swivel base for audio power 9E/9Elr 9EA/9ElrAFigure 2 Connecting Cables1. Power Cord 4. PC Audio Output2. Signal Cable 5. DC Output3. VGA Card Adapter
6OPERATING INSTRUCTIONSGENERAL INSTRUCTIONSThe power switch is located at front panel of the monitor. Press the powerswitch to turn the monitor on or off. The other control knobs are located at thebase of the monitor (See Figure 3). By changing these settings, the picture canbe adjusted to your personal preferences.?The power cord should be connected.?Connect the video cable from the monitor to the video card.?To turn the monitor on, press the POWER switch to ON position. The powerindicator will light up.?Your monitor features a unique quick switch system which provides a picturewithin seconds after the monitor is switched on.9E/9Elr 9EA/9ElrAFigure 3 External Control KnobEXTERNAL CONTROLSSwitch: Functions:1. Power On/Off Switch 6. Contrast 11. V-Center2. LED 7. Brightness 12. Pincushion3. Up Key 8. H-Size 13. Trapezoid4. Down Key 9. H-Center 3+4.Recall5. Function Key 10. V-Size 4+5. Degauss12+13.Rotation?Functions:( 9EA/9ElrA ONLY)14. Audio power indicator 16. Volume15. Audio power ON/OFF 17. Earphone Jack
7NOTES?Do not install the monitor in a location near heat sources such as radiatorsor air ducts , or in a place subject to direct sunlight , or excessive dust ormechanical vibration or shock.?Save the original shipping carton and packing materials, as they will come inhandy if you ever have to ship your monitor.?For maximum protection, repackage your monitor as it was originally packedat the factory.?To keep the monitor looking new, periodically clean it with a soft cloth.Stubborn stains may be removed with a cloth lightly dampened with a milddetergent solution. Never use strong solvents such as thinner, benzene, orabrasive cleaners, since these will damage the cabinet. As a safetyprecaution, always unplug the monitor before cleaning it.HOW TO ADJUST A SETTING1. Press the knob, the green LED lights and the power is ON.Press this knob again, the green LED disappears and the power is OFF.2. When press the “FUNC” key, the LED will flash to indicate the function hasbeen selected.3. When function has been selected, press or to adjust picture image.4. When eight LEDs don't flash, directly press to select the brightnessfunction or press to select the contrast function.5. Press the “FUNC” key until the LEDs of pincushion and trapezoid flashsimultaneously, then press Up or Down key to adjust the picture tilt tohorizontal position.6. If color impurity occurs when moving or swiveling the monitor, press theFunc. key and Down key together as manual degauss function to fix thepicture condition.
8ADJUSTING THE PICTUREThe description for function control LEDS1. CONTRAST Adjust the picture contrast.2. BRIGHTNESS Adjust the picture brightness.3. H-SIZE Adjust the picture’s horizontal size.4. H-CENTER Adjust the horizontal position of the picture.5. V-SIZE Adjust the picture’s vertical size.6. V-CENTER Adjust the vertical position of the picture.7. PINCUSHION Adjust the pincushion and barrel.8. TRAPEZOID Adjust the picture’s trapezoid distortion.9. +RECALL To recall original factory preset mode.10. +ROTATION Adjust the picture’s tilt to horizontal position.11. FUNC.+ DEGAUSS Fix the picture condition.POWER MANAGEMENT FEATUREThe power management feature of this product complies with every powersaving requirements of ENERGY STAR? and VESA DPMS when activated, itautomatically reduces unnecessary power consumption of the monitor whenyour computer is not in use.To use the feature, the monitor needs to be connected to a VESA DPMScomputer. There are three power management modes available, these aredescribed below. The required settings, including the timer setting, should bemade by the computer.?Stand-by ModeWhen the H-sync signal from the computer is off, the monitor enters intoStand-by Mode which reduces the power consumption to less than 15W. Thescreen becomes dark, and the power indicator turns to orange. From Stand-by Mode, the screen reappears instantaneously when the keyboard or themouse is touched again.
9
10?Suspend ModeWhen the V-sync signal from the computer is off, the monitor enters intoSuspend Mode which reduces the power consumption to less than 15W. Thescreen becomes dark, and the power indicator turns to orange. FromSuspend Mode, the screen reappears instantaneously when the keyboard orthe mouse is touched again.?Active-off ModeWhen both the H and V sync signals form the computer are off, the monitorenters into Active-off Mode which reduces the power consumption to lessthan 8W. The screen becomes dark, and the power indicator turns to orange.From Active-off Mode, the screen reappears instantaneously when thekeyboard or the mouse is touched again.?The power-saving mode can be indicated by the light-emitting diode (LED)on the front panel: Signal PowerMode Cable H-Sync V-Sync Video Indicator ConsumptionOn*Attached Yes Yes Active Green ? 120 WStand-by Attached No Yes Blank Orange ? 15 WSuspend Attached Yes No Blank Orange ? 15 WOff Attached No No Blank Orange ? 8 WFEATURESGreen monitor?The monitor has a power saving function that conforms to the VESA DPMSstandard. This feature will only work if your PC is a green PC. This feature issimilar to a screen saver, except that your monitor will turn it off instead ofactivating the screen saver.To activate this feature in Windows® 98 :In Windows® 98, this feature can be activated and customized under the screensaver setting of the display properties.1. Right click on the desktop and choose Properties.2. Click on the tab that says Screen Saver. If your system supports Green PC,there will be a section entitled “Energy Saving Features of Monitor.” If thereisn’t a section like that, then your PC does not support Green Monitor. Themonitor will behave just like a normal monitor, so you will have to turn it offmanually to save energy.3. In the “Energy Saving Features of Monitor” sections are two boxes, Standbyand Shut off. To activate either one, click the box next to each one.4. You can specify the amount of inactive time before your monitor entersstandby mode or shuts off. PLUG AND PLAY
11Plug & Play DDC1/2B FeatureThis monitor is equipped with VESA DDC1/2B capabilities according to theVESA DDC STANDARD. It allows the monitor to inform the host system of itsidentity and, depending on the level of DDC used, communicate additionalinformation about its display capabilities. The communication channel is definedin two levels, DDC1 and DDC2B.The DDC1 is a unidirectional data channel from the display to the host thatcontinuously transmits EDID information. The DDC2B is a bidirectional datachannel based on the I²C protocol. The host can request EDID information overthe DDC2B channel.THIS MONITOR WILL APPEAR TO BE NON-FUNCTIONAL IF THERE ISNO VIDEO INPUT SIGNAL. IN ORDER FOR THIS MONITOR TO OPERATEPROPERLY, THERE MUST BE A VIDEO INPUT SIGNAL.This monitor meets the Power Management standards as set by the VideoElectronics Standards Association (VESA) and/or the United StatesEnvironmental Protection Agency (EPA) and The Swedish ConfederationEmployees ( NUTEK ). This feature is designed to conserve electrical energy byreducing power consumption when there is no video input signal present. Whenthere is no video input signal this monitor, following a time-out period, willautomatically switch to an OFF mode. This reduces the monitor's internal powersupply consumption. After the video input signal is restored, full power isrestored and the display is automatically redrawn. The appearance is similar to a"Screen Saver" feature except the display is completely off. The display isrestored by pressing a key on the keyboard, or clicking the mouse.USING THE RIGHT POWER CORD :The accessory power cord for the Northern American region is the wallet plugwith NEMA 5-15 style and is UL listed and CSA labeled. The voltage rating for thepower cord shall be 125 volts AC.Supplied with units intended for connection to power outlet of personalcomputer: Please use a cord set consisting of a minimum No. 18 AWG, typeSJT or SVT three conductors flexible cord. One end terminates with a groundingtype attachment plug, rated 10A, 250V, CEE-22 male configuration. The otherend terminates with a molded-on type connector body, rated 10A, 250V, havingstandard CEE-22 female configuration.
12TECHNICAL SUPPORT (FAQ)Problem & Question Possible SolutionPower LED is not on *Check if the Power Switch is in the ONposition*Power Cord should be connectedNo Plug & Play *Check if the PC system is Plug & Playcompatible*Check if the Video Card is Plug & Playcompatible*Check if the D-15 plug pin of Video Cableis bent*Make sure the ENVISION Monitor Driversare installed(ENVISION Monitor Drivers are availableat: www.epius.com)No picture *Computer Power Switch should be in theON position*Computer Video Card should be snuglyseated in its slot*The Signal Cable should be completelyconnected to the computer*Check the color of the Power LEDindicator. If it is orange, then the monitorand the PC system are in power-savingmode. You need press your keyboard ormove the mouse to reactivate the system.Picture is fuzzy *Adjust the Contrast and BrightnessControls.Picture bounces or a wavepattern is present in the picture *Move electrical devices that may causeelectrical interference.Monitor is stuck in “PowerSaving Mode” *Make sure monitor’s video cable is properlyconnected to the computer.*Inspect monitor’s video cable and makesure none of the pins are bent.*Make sure computer is operational byhitting the CAPS LOCK key on thekeyboard while observing the CAPS LOCKLED. The LED should either turn ON orOFF after hitting the CAPS LOCK key.Missing one of the primarycolors (RED, GREEN, or BLUE) *Inspect the monitor’s video cable andmake sure that none of the pins are bent.North America technicalsupport telephone number: 1-800-343-5777
13APPENDIXSPECIFICATIONSCRT Size 48.3cm(19"), 90º deflection, 29mmneck,CRT Viewable ImageSize 45.7cm (18"), diagonalType 0.27mm dot pitch.Video 0.7Vpp, R,G,B AnalogInput Separate Sync. TTL LevelH./V.- Sync. Positive / NegativeScanning H-Frequency 30kHz - 95kHzFrequency V-Frequency 50Hz-160HzMax. Resolution 1600 x 1200Video Dot Rate 200MHzFactory Preset mode :8User Programmable mode : 10Power Source Universal AC 100 - 240V,50Hz / 60HzOperating 0ºC to 40ºC ambientHumidity 10%to 85%relative, non-condensingDimensions9E/9Elr : Monitor & Base 446(W) × 436(H) × 455(D)mm9EA/9ElrA : Monitor & Base 446(W) × 485(H) × 455(D)mmWeight9E/9Elr : Unit (net) 18.4kg ( Net )9EA/9ElrA : Unit (net) 19.4kg ( Net )Signal Cable: Attached Mini D-sub 15 Male446436(ln mm)4559E/9Elr 9E/9Elr
14Switch ?Power On/Off switch?UP/Down Key?Function Key?Volume(9EA/9ElrA)External Controls: Functions ?Contrast?Brightness?H-Center?H-Size?V-Center?V-Size?Pincushion?Trapezoid?Rotation?Degauss?RecallPlug & Play DDC1/2BPower Management EPA, VESA DPMSPower Consumption ( Maximum ) 120 WattsPre-set Display Area 346mm x 260mmAudio Output(for 9EA/9ElrA only) Rated Power 1W rms(Per channel)Regulatory Compliance UL, CSA, FDA, FCC, TÜV/GS, CE,MPR IITCO’95 or TCO’99 (Optional)9EA/9ElrA 9EA/9ElrA
15FACTORY PRESET TIMING TABLESTANDARD RESOLUTION HORIZONTALFREQUENCY VERTICALFREQUENCYVGA 720 × 400 31.5kHz 70HzVGA 640 × 480 31.5kHz 60HzVESA/85 640 × 480 43.3kHz 85HzVESA/85 800 × 600 53.7kHz 85HzVESA/85 1024 × 768 68.7kHz 85HzVESA/85 1280 × 960 85.9kHz 85HzVESA/85 1280× 1024 91.1kHz 85HzVESA/75 1600× 1200 93.8kHz 75HzCONNECTOR PIN ASSIGNMENT1 561011 1515 - Pin Color Display Signal CablePIN NO. DESCRIPTION PI N NO. DESCRIPTION1. Red 9. NC2. Green 10. Ground3. Blue 11. Monitor Ground4. Ground 12. DDC-Serial Data5. Ground 13. H-Sync6. R-Ground 14. V-Sync / ?V-Clk7. G-Ground 15. DDC-Serial Clock8. B-Ground ?For DDC

Navigation menu