Top Victory Electronics LM561S 15" LCD Monitor User Manual LM510 969 4A

Top Victory Electronics (Taiwan) Co Ltd 15" LCD Monitor LM510 969 4A

Contents

LM510 users manual

Plug & Play Drivers for the AOC Spectrum Series Monitors are availableat AOC’s Web Site: www.AOCmonitor.comLM-510USER MANUALTABLE OF CONTENTSFOR YOUR SAFETY -------------------------------------------------- 1SAFETY PRECAUTIONS -------------------------------------- 2SPECIAL NOTES ON LCD MONITORS ------------------- 3BEFORE YOU OPERATE THE MONITOR --------------------- 3FEATURES -------------------------------------------------------- 3PACKING LIST --------------------------------------------------- 3INSTALLATION INSTRUCTIONS --------------------------- 4CONTROLS AND CONNECTORS -------------------------- 5ADJUSTING THE VIEWING ANGLE ------------------------ 6OPERATING INSTRUCTIONS ------------------------------------- 7GENERAL INSTRUCTIONS ---------------------------------- 7HOW TO ADJUST A SETTING ------------------------------- 9ADJUSTING THE PICTURE -------------------------------- 9-10HOW TO OPTIMIZE THE DOS-MODE----------------------- 10PLUG AND PLAY -------------------------------------------------- 11TECHNICAL SUPPORT(FAQ) ----------------------------------- 12-13ERROR MESSAGE & POSSIBLE SOLUTION ----------- 14HOW TO INSTALL INF & ICM FILE --------------------------- 15APPENDIX ----------------------------------------------------------------- 16SPECIFICATIONS --------------------------------------------- 16-17FACTORY PRESET TIMING TABLE -------------------------- 18CONNECTOR PIN ASSIGNMENT ----------------------------- 18LIMITED THREE-YEAR WARRANTY --------------------------- 19-20Thank you very much for choosing AOC LM-510 LCD Monitor.We recommend that you take a few minutes to read carefully through thismanual before installing and switching on the monitor. Please keep thismanual in a safe place for your future reference.
1Before operating the monitor please read this manual thoroughly. Thismanual should be retained for future reference.FCC Class B Radio Frequency Interference StatementWARNING: (FOR FCC CERTIFIED MODELS)NOTE: This equipment has been tested and found to comply with the limitsfor a Class B digital device, pursuant to Part 15 of the FCC Rules. Theselimits are designed to provide reasonable protection against harmfulinterference in a residential installation. This equipment generates, uses andcan radiate radio frequency energy, and if not installed and used inaccordance with the instructions, may cause harmful interference to radiocommunications. However, there is no guarantee that interference will notoccur in a particular installation. If this equipment does cause harmfulinterference to radio or television reception, which can be determined byturning the equipment off and on, the user is encouraged to try to correct theinterference by one or more of the following measures:1. Reorient or relocate the receiving antenna.2. Increase the separation between the equipment and receiver.3. Connect the equipment into an outlet on a circuit different from that towhich the receiver is connected.4. Consult the dealer or an experienced radio/TV technician for help. NOTICE1. The changes or modifications not expressly approved by the partyresponsible for compliance could void the user's authority to operate theequipment.2. Shielded interface cables and AC power cord, if any, must be used inorder to comply with the emission limits.3. The manufacturer is not responsible for any radio or TV interferencecaused by unauthorized modification to this equipment. It is theresponsibilities of the user to correct such interference.As an ENERGY STAR Partner Envision Peripherals, Inc. has determinedthat this product meets the ENERGY STAR guidelines for energy efficiency. WARNING:To prevent fire or shock hazard, do not expose the monitor to rain or moisture.Dangerously high voltages are present inside the monitor. Do not open thecabinet. Refer servicing to qualified personnel only.
2lDo not use the monitor near water, e.g. near a bathtub, washbowl, kitchensink, laundry tub, swimming pool or in a wet basement.lDo not place the monitor on an unstable cart, stand, or table. If themonitor falls, it can injure a person and cause serious damage to theappliance. Use only a cart or stand recommended by the manufacturer orsold with the monitor. If you mount the monitor on a wall or shelf, use amounting kit approved by the manufacturer and follow the kit instructions.lSlots and openings in the back and bottom of the cabinet are provided forventilation. To ensure reliable operation of the monitor and to protect itfrom overheating, be sure these openings are not blocked or covered. Donot place the monitor on a bed, sofa, rug, or similar surface. Do not placethe monitor near or over a radiator or heat register. Do not place themonitor in a bookcase or cabinet unless proper ventilation is provided.lThe monitor should be operated only from the type of power sourceindicated on the label. If you are not sure of the type of power supplied toyour home, consult your dealer or local power company.lThe monitor is equipped with a three-pronged grounded plug, a plug witha third (grounding) pin. This plug will fit only into a grounded power outletas a safety feature. If your outlet does not accommodate the three-wireplug, have an electrician install the correct outlet, or use an adapter toground the appliance safely. Do not defeat the safety purpose of thegrounded plug.lUnplug the unit during a lightning storm or when it will not be used for longperiods of time. This will protect the monitor from damage due to powersurges.lDo not overload power strips and extension cords. Overloading can resultin fire or electric shock.lNever push any object into the slot on the monitor cabinet. It could shortcircuit parts causing a fire or electric shock. Never spill liquids on themonitor.lDo not attempt to service the monitor yourself; opening or removingcovers can expose you to dangerous voltages and other hazards. Pleaserefer all servicing to qualified service personnel.lTo ensure satisfactory operation, use the monitor only with UL listedcomputers which have appropriate configured receptacles markedbetween 100 - 240V AC, Output 12Vdc Min. 3.5A.lThe wall socket shall be installed near the equipment and shall be easilyaccessible.lFor use only with power adaptor manufacturer by :Li Shin LSE9901B1250Delta ADP-50XB, ADP-40TBLinearity LAD6019AB4Samsung 80AL15-7-SS(SA) (IBM)PRECAUTIONS
3The following symptoms are normal with LCD monitor and do not indicate aproblem. NOTES•Due to the nature of thefluorescent light, the screen may flicker duringinitial use. Turn off the Power Switch and then turn it on again to makesure the flicker disappears.•You may find slightly uneven brightness on the screen depending on thedesktop pattern you use.•The LCD screen has effective pixels of 99.99% or more. It may includeblemishes of 0.01% or less such as a missing pixel or a pixel lit all of thetime.•Due to the nature of the LCD screen, an afterimage of the previous screenmay remain after switching the image, when the same image is displayedfor hours. In this case, the screen is recovered slowly by changing theimage or turning off the Power Switch for hours.•The life of the fluorescent light used in the LCD monitor is approximately10,000 hours. Contact your dealer or EPI service center for replacementwhen the screen is dark, flickering or not lighting up. Never attempt toreplace it by yourself.BEFORE YOU OPERATE THE MONITOR FEATURES•38.1cm(15”) TFT Color LCD Monitor•Crisp, Clear Display for Windows•Recommened Resolutions: 1024 X 768 @60Hz•EPA ENERGY STAR®•Ergonomic Design (MPRII Approved)•Space Saving, Compact Case Design The product package should include the following items:1. LCD Monitor2. Owner's Manual3. Power Cord4. External Adapter5. Driver-DiskFEATURESCHECKING THE CONTENTS OF THE LM-510 PACKAGESPECIAL NOTES ON LCD MONITORS
4 INSTALLATION INSTRUCTIONS SWIVEL BASEInstall Remove Figure 1 Installing and Removing the Swivel Base POWERCORDPower Source:1. Make sure the power cord is the correct type that required in your area.2. This LCD monitor has a universal power supply that allows operation ineither 100/120V AC or 220/240V AC voltage area (No user adjustment isrequired.)3. Connect the power cord into your LCD monitor’s power input socket, andthen plug the other end into a 3-pin AC power outlet. The power cord maybe connected to either a wall power outlet or the power outlet socket onyour PC, depending on the type of power cord supplied with your LCDmonitor. NOTESA certified power supply cord has to be used with this equipment. Therelevant national installation and/or equipment regulations shall beconsidered. A certified power supply cord not lighter than ordinary polyvinylchloride flexible cord according to IEC 60227 (designation H05VV-F 3G0.75mmcord be of synthetic rubber according to IEC 60245 (designation H05RR-F 3G0.75mmINSTALLATION INSTRUCTIONS
5 VIDEO CABLEConnecting the Video Cable: the LCD monitor comes with a built-in videocable. Plug the signal cable′s 15-pin connector into the computer's video portand tighten the two screws on the cable connector.Connecting the Power Cord: Plug the power cord into the LCD monitor's ACpower socket. Then plug the power cord into a grounded AC outlet or UL-approved power strip or the power output socket on your PC.Caution: If the AC outlet is not grounded (with three holes), install the propergrounding adapter (not supplied).Figure 2 Connecting Cables1. Signal Cable 3. AC Power Cord2. DC-Jack Power Cable 4. External AdapterCONTROLS AND CONNECTORS
6 INSTALLATION INSTRUCTIONS•For optimal viewing it is recommended to look at the full face of themonitor, then adjust the monitor’s angle to your own preference.•Hold the stand so you do not topple the monitor when you change themonitor’s angle.•You are able to adjust the monitor’s angle from -5° to 25°.Figure 3 NOTES•Do not touch the LCD screen when you change the angle. It may causedamage or break the LCD screen.•Careful attention is required not to catch your fingers or hands when youchange the angle.ADJUSTING THE VIEWING ANGLE
7OPERATING INSTRUCTIONS Press the power button to turn the monitor on or off. The other control knobsare located at front panel of the monitor (See Figure 4). By changing thesesettings, the picture can be adjusted to your personal preferences.•The power cord should be connected.•Connect the video cable from the monitor to the video card.•Press the power button to turn on the monitor position. The powerindicator will light up.Figure 4 External Control Knob EXTERNAL CONTROLS1. Auto Config / Exit 2. / Brightness3. / Contrast 4. MENU / ENTER5. Power Button 6. LEDGENERAL INSTRUCTIONS
8 FRONT PANEL CONTROL•Power:Press this knob to switch ON/OFF of monitor’s power.•MENU/Exit :Active OSD menu or function adjust confirm or Exit OSD menu when inBrightness/Contrast OSD status.•Contrast / :Adjust contrast or function adjust.•Brightness / :Adjust brightness or function adjust.•Auto Config Key:The Auto Adjust Key is used to automatically set the H POs, V Pos, Clockand Focus.•Power Indicator:Green —Power On mode.Orange —Off mode. NOTES•Do not install the monitor in a location near heat sources such asradiators or air ducts, or in a place subject to direct sunlight, or excessivedust or mechanical vibration or shock.•Save the original shipping carton and packing materials, as they will comein handy if you ever have to ship your monitor.•For maximum protection, repackage your monitor as it was originallypacked at the factory.•To keep the monitor looking new, periodically clean it with a soft cloth.Stubborn stains may be removed with a cloth lightly dampened with a milddetergent solution. Never use strong solvents such as thinner, benzene,or abrasive cleaners, since these will damage the cabinet. As a safetyprecaution, always unplug the monitor before cleaning it.
9 1. Press the MENU-Key to make the OSD window appear. See figure 5.2. Press or to select the desired function. See figure 5.3. Press the MENU-Key to select the function that you want to adjust.4. Press or to change the settings of the current function.5. When the OSD window is active, it shows the input signal timing. The "H"stands for the horizontal frequency and "V" for the vertical frequency.6. To exit and save, select the exit functions, or leave the monitor alone for10 seconds. If you want to adjust any other function, repeat steps 2-4.Figure 5 The OSD Message The description for function control LEDS1. Contrast Adjust the picture contrast.2. Brightness Adjust the picture brightness.3. Focus Adjust picture Focus.4. Clock Adjust picture Clock.5. H- Position Adjust the horizontal position of the picture.6. V- Position Adjust the vertical position of the picture.7. Language Multi-Language selectionADJUSTING THE PICTUREHOW TO ADJUST A SETTING
108. Red Adjusts Red intensity.9. Green Adjusts Green intensity.10. Blue Adjusts Blue intensity.11. 73 (7300K) Color The color temperature for 7300°K isx=0.301, y=0.317.12. 93 (9300K) Color The color temperature for 9300°K isx=0.281, y=0.311.13. Reset Clear each old status of auto-configuration And re-do auto-configuration.14. Exit Save user adjustment and OSD disappear.1. Use the full-screen pattern which is attached in your driver-disk to start theadjustment ( press twice at Dos1.exe , and expand the picture to fullscreen with pressing the icon on the top of window, but there isnothing to press if the picture is already full screen )If you don’t have monitor driver disk, you can try the following way to getthe full screen pattern at MS-DOS mode , type in C:\> EDIT [press enter]You will be in the Dos-Editor screen2. Press “AUTO” button( at front bezel) during 2 seconds , the monitors willdo all the adjustment automatically3. Press “ESC” to quit the pattern file ,or press ALT-F, and then X to exitfrom the Dos-Editor screenIf the DOS-MODE characters still have distortionexample : ●the picture can’t go to full screen●the background of white pattern has vertical stripe noise●the character twistedthat means your monitor parameter was in wrong resolution, please check ifyour VGA-CARD supports 720x400 @ 70 Hzin general, most of the Dos mode was set by VGA-CARD in resolution720x400@70Hz, but minor was set in 640x400 @ 70Hz ( our monitor onlysupports 720x400@70Hz)HOW TO OPTIMIZE THE DOS-MODE
11 Plug & Play DDC1/2B FeatureThis monitor is equipped with VESA DDC1/2B capabilities according to theVESA DDC STANDARD. It allows the monitor to inform the host system of itsidentity and, depending on the level of DDC used, communicate additionalinformation about its display capabilities. The communication channel isdefined in two levels, DDC1 and DDC2B.The DDC1 is a unidirectional data channel from the display to the host thatcontinuously transmits EDID information. The DDC2B is a bidirectional datachannel based on the I²C protocol. The host can request EDID informationover the DDC2B channel.THIS MONITOR WILL APPEAR TO BE NON-FUNCTIONAL IF THERE ISNO VIDEO INPUT SIGNAL. IN ORDER FOR THIS MONITOR TO OPERATEPROPERLY, THERE MUST BE A VIDEO INPUT SIGNAL.This monitor meets the Green monitor standards as set by the VideoElectronics Standards Association (VESA) and/or the United StatesEnvironmental Protection Agency (EPA) and The Swedish ConfederationEmployees (NUTEK). This feature is designed to conserve electrical energyby reducing power consumption when there is no video-input signal present.When there is no video input signal this monitor, following a time-out period,will automatically switch to an OFF mode. This reduces the monitor's internalpower supply consumption. After the video input signal is restored, full poweris restored and the display is automatically redrawn. The appearance issimilar to a "Screen Saver" feature except the display is completely off. Thedisplay is restored by pressing a key on the keyboard, or clicking the mouse. USING THE RIGHT POWER CORD :The accessory power cord for the Northern American region is the wallet plugwith NEMA 5-15 style and is UL listed and CSA labeled. The voltage rating forthe power cord shall be 125 volts AC.Supplied with units intended for connection to power outlet of personalcomputer: Please use a cord set consisting of a minimum No. 18 AWG, typeSJT or SVT three conductors flexible cord. One end terminates with agrounding type attachment plug, rated 10A, 250V, CEE-22 male configuration.The other end terminates with a molded-on type connector body, rated 10A,250V, having standard CEE-22 female configuration.Please note that power supply cord needs to use VDE 0602, 0625, 0821approval power cord in European counties.PLUG AND PLAY
12TECHNICAL SUPPORT (FAQ)Problem & Question Possible SolutionPower LED is not on *Check if the Power Switch is in the ONposition*Power Cord should be connectedNo Plug & Play *Check if the PC system is Plug & Playcompatible*Check if the Video Card is Plug & Playcompatible*Check if the D-15 plug pin of VideoCable is bent*Make sure the AOC Monitor Drivers areinstalled(AOC Monitor Drivers are available at:www.AOCmonitor.com)Picture is fuzzy *Adjust the Contrast and BrightnessControls.Picture bounces or a wavepattern is present in the picture *Move electrical devices that may causeelectrical interference.The power LED is ON (orange)but there’s no video or nopicture.*Computer Power Switch should be inthe ON position.*Computer Video Card should be snuglyseated in its slot*Make sure monitor’s video cable isproperly connected to the computer.*Inspect monitor’s video cable and makesure none of the pins are bent.*Make sure computer is operational byhitting the CAPS LOCK key on thekeyboard while observing the CAPSLOCK LED. The LED should eitherturn ON or OFF after hitting the CAPSLOCK key.Missing one of the primarycolors (RED, GREEN, orBLUE)*Inspect the monitor’s video cable andmake sure that none of the pins arebent.
13Screen image is not centered or sizedproperly. *Adjust pixel frequency (CLOCK) andFOCUS or press hot-key (AUTO)Picture has color defects(white does not look white) *Adjust RGB color or select colortemperaturePoor brightness or contrast *The life time of the back-light islimited.In 10000 Hours the luminanceof the light has been reduced to halfof its original value. Please send themonitor to an authorized serviceAgent for service.Horizontal or vertical disturbancies onthe screen *Use win 95/98 shut-down modeAdjust CLOCK and FOCUS orperform hot- key (AUTO-key).CLOCK (pixel frequency) controls the number of pixels scanned by onehorizontal sweep. If the frequency is not correct, the screen shows verticalstripes and the picture has not correct width.FOCUS adjust the phase of the pixel clock signal. With a wrong phaseadjustment the picture has horizontal disturbances in light picture.For FOCUS and CLOCK adjustment use “dot-pattern” or win 95/98 shut-downmode pattern .
14 CABLE NOT CONNECTED :1. Check that the signal-cable is properly connected , If the connector isloose, tighten the connector’s screws.2. Check the signal-cable’s connection pins for damage. INPUT NOT SUPPORT :Your computer has been set to unsuitable display mode ,Set the computer todisplay mode given in the following table. UNSUPPORTED MODE TRY DIFFERENT VIDEO CARD SETTING:Your computer resolution is out of VESA-SPEC RESOLUTION :RESOLUTION VERTICALFREQUENCY RESOLUTION VERTICALFREQUENCY640 × 480 60Hz 800 × 600 60.3Hz640 × 350 70Hz 800 × 600 72.2Hz720 × 400 70Hz 800 × 600 75Hz640 × 480 72.8Hz 832 × 624 74.5Hz640 × 480 75Hz 1024 × 768 60Hz640 × 480 66.67Hz 1024 × 768 70Hz800 × 600 56.3Hz 1024 × 768 75Hz1024 × 768 74.92HzERROR MESSAGE & POSSIBLE SOLUTION
15 FOR FIRST TIME INSTALL :1. Check this LCD MONITOR LM-510 is properly connected to yourcomputer.2. Restart the computer , when win98 detects the presence of a Plug andPlay Monitor ,its device driver can be loaded and configured dynamically,insert LM-510 install disk to DISK A after the Win95/98 setup wizard isappear. This setup wizard will lead you through the steps for configuringthe system.(Select “ NEXT “ for next steps and select driver A for LM-510 install file,if not select driver A ,the configuration system will automatic select thestandard Plug and Play driver)3. After the installation complete you can find the monitor complete nameby following steps :Click “START” , select “SETTINGS”, select “CONTROL PANEL “Select“SYSTEM”, select “DEVICE MANAGEMENT“, select “MONITOR” iconand click twice ,you can see the Description as follow :“AOC LCD MONITOR LM-510 “if this description doesn’t exist, or the “MONITOR” icon no exist too,thatmeans your installation not success.Please delete the Description with click the right button of mouse, andselect The “remove or erase” to delete the description, if your steps issuccess, the “MONITOR “ icon will disappear.Please repeat this 2, 3 steps if not successHOW TO INSTALL INF & ICM FILE
16APPENDIX SPECIFICATIONSDriving system TFT Color LCDLCD Panel Size 38.1cm(15.0")Pixel pitch 0.297mm( H )x 0.297mm( V )Viewable angle 120° (H) 85° (V)Response time 50 msVideo R,G,B Analog InterfaceInput Separate Sync. H/V TTLH-Frequency 30kHz – 60kHzV-Frequency 55-75HzDisplay Colors 16.7 million Colors (for CPTpanel)Dot Clock 80MHzMax. Resolution 1024 x 768Plug & Play VESA DDC1/2BTMEPA ENERGY STAR®ON Mode <25W ( For 2 CCFL)<35W ( For 4 CCFL)OFF Mode <3WInput Connector D-Sub 15pinInput Video Signal Analog:0.7Vp-p(standard),75 OHM, PositiveMaximum Screen Size Horizontal : 12.0”(304.1mm)Vertical : 9.0”(228.1mm)Power Source 12Vdc 4AEnvironmentalConsiderations Operating Temp: 0° to 40°CStorage Temp.: -20° to 60°COperating Humidity : 10% to 90%Weight (N. W.) 4.7kgs
17Switch •Auto Adjust Key• / Brightness• / Contrast•Power Switch•MENU/ ExitExternal Controls: Functions •Contrast•Brightness•Focus•Clock•H-Position•V-Position•Language•7300°K•9300°K•RGB Color temperature•Reset•ExitRegulatoryCompliance UL, CSA, FCC, TÜV, CE,ISO13406-2, MPR IITCO’99
18STANDARD RESOLUTION HORIZONTALFREQUENCY VERTICALFREQUENCY720 × 400 31.47kHz 70HzVGA 640 × 480 31.47kHz 60Hz640 × 480 35.00kHz 66.6Hz640 × 480 37.50kHz 75Hz800 × 600 37.879kHz 60HzSVGA 800 × 600 46.875kHz 75Hz832 × 624 49.725kHz 75Hz1024 × 768 48.363kHz 60HzXGA 1024 × 768 56.476kHz 70Hz1024 × 768 60.02kHz 75Hz1024 × 768 60.241kHz 74.9Hz1 561011 1515 - Pin Color Display Signal CablePIN NO. DESCRIPTION PI N NO. DESCRIPTION1. Red 9. +5V2. Green 10. Detect Cable3. Blue 11. Ground4. Ground 12. DDC-Serial Data5. Ground 13. H-Sync6. R-Ground 14. V-Sync7. G-Ground 15. DDC-Serial Clock8. B-GroundFACTORY PRESET TIMING TABLECONNECTOR PIN ASSIGNMENT
19 WARRANTY STATEMENTfor AOC Color MonitorsIncluding those Sold within North America as SpecifiedEnvision Peripherals, Inc. warrants this product to be free from defects inmaterial and workmanship for a period of three (3) years after the originaldate of consumer purchase. During this period, EPI (EPI is the abbreviationfor Envision Peripherals, Inc.) will, at its option, either repair the defectiveproduct with new or rebuilt parts, or replace it with a new or rebuilt product atno charge except as *stated below. The parts or product that are replacedbecome the property of EPI.In the USA to obtain service under this limited warranty, call EPI for thename of the Authorized Service Center in your area. Deliver the productfreight pre-paid, along with the dated proof of purchase, to the EPIAuthorized Service Center. If you cannot deliver the product in person:lPack it in its original shipping container (or equivalent)lPut the RMA number on the address labellPut the RMA number on the shipping cartonlInsure it (or assume the risk of loss / damage during shipment)lPay all shipping chargesEPI is not responsible for damage to inbound product that was not properlypackaged.EPI will pay the return shipment charges within one of the countries specifiedwithin this warranty statement. EPI is not responsible for any costs associatedwith the transportation of product across international borders. This includesthe international borders of the countries within this warranty statement.In the United States and Canada contact your Dealer or EPI Customer Service,RMA Department at the toll free number (888) 838-6388.* This limited warranty does not cover any losses or damages that occur as aresult of:lShipping or improper installation or maintenancelMisuselNeglectlAny cause other than ordinary commercial or industrial applicationlAdjustment by non-authorized sourcelRepair, modification, or installation of options or parts by anyone otherthan an EPI Authorized Service Center
20lImproper environmentlExcessive or inadequate heating or air conditioning or electrical powerfailures, surges, or other irregularitiesThis three-year limited warranty does not cover any of the product's firmwareor hardware that you or any third party have modified or altered; you bear thesole responsibility and liability for any such modification or alteration.ALL EXPRESS AND IMPLIED WARRANTIES FOR THIS PRODUCT(INCLUDING THE WARRANTIES OF MERCHANTABILITY ANDFITNESS FOR A PARTICULAR PURPOSE) ARE LIMITED INDURATION TO A PERIOD OF THREE (3) YEARS FOR PARTS ANDLABOR FROM THE ORIGINAL DATE OF CONSUMER PURCHASE.NO WARRANTIES (EITHER EXPRESSED OR IMPLIED) APPLYAFTER THIS PERIOD. IN THE UNITED STATES OF AMERICA, SOMESTATES DO NOT ALLOW LIMITATIONS ON HOW LONG ANIMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATIONS MAYNOT APPLY TO YOU.EPI OBLIGATIONS AND YOUR REMEDIES HEREUNDER ARESOLELY AND EXCLUSIVELY AS STATED HERE. EPI’S LIABILITY,WHETHER BASED ON CONTRACT, TORT. WARRANTY, STRICTLIABILITY, OR OTHER THEORY, SHALL NOT EXCEED THE PRICEOF THE INDIVIDUAL UNIT WHOSE DEFECT OR DAMAGE IS THEBASIS OF THE CLAIM. IN NO EVENT SHALL ENVISIONPERIPHERALS, INC. BE LIABLE FOR ANY LOSS OF PROFITS, LOSSOF USE OR FACILITIES OR EQUIPMENT OR OTHER INDIRECT,INCIDENTAL, OR CONSEQUENTIAL DAMAGE. IN THE UNITEDSTATES OF AMERICA, SOME STATES DO NOT ALLOW THEEXCLUSION OR LIMITATION OF INCIDENTAL ORCONSEQUENTIAL DAMAGES. SO THE ABOVE LIMITATION MAYNOT APPLY TO YOU. ALTHOUGH THIS LIMITED WARRANTYGIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY HAVE OTHERRIGHTS WHICH MAY VARY FROM STATE TO STATE.In the United States of America, this limited warranty is only valid forProducts purchased in the Continental United States, Alaska, and Hawaii.Outside the United States of America, this limited warranty is only valid forProducts purchased in Canada.
21Only for AOC branded monitors sold within the continental United States.All AOC branded monitors that are purchased after April 1st, 2001 are now coveredby the EASE Program. If your monitor malfunctions at any time during the first year,AOC will provide a replacement monitor within 72 hours after you are approved forour program. If your monitor qualifies for the EASE program, AOC will pay forfreight both ways.Step 1: Phone our TECH Department at 888.662.9888Step 2: Fill out and return EASE registration forms by mail or fax.Step 3: We will issue a Return Authorization Number upon verification into theprogram.Step 4: A monitor will be advance shipped to your location.Step 5: We will issue a UPS Call Tag to pick up the defective unit.Step 6: Please review the following chart to see your EASE program qualificationsWARRANTYPERIOD COVERAGE ATNO CHARGE CUSTOMERCHARGESWithin the 1st year of purchaseCovered by EASE •New AOC monitor•Call tag dispatched and returnfreight charges via UPS•None*Between 1-3 Years •All Parts & Labor•AOC repaired monitor•UPS Return Freight to AOC*AOC will need to obtain a credit card number if you would like to get a new AOCmonitor advanced shipped to your location, prior to the defective unit arriving atAOC’s service center. If you do not wish to supply a credit card, AOC will only shipthe new monitor, once the defective unit arrives at the AOC service center.www.AOCmonitor.com
22P/N : 41A401-969

Navigation menu