Tranzeo Wireless Technologies RAKT3KN2 WIRELESS MESH ROUTER User Manual USERS MANUAL 1

Download:
Mirror Download [FCC.gov]
Document ID	797586
Application ID	5lOpoiK7b216NC4kV4kTlg==
Document Description	USERS MANUAL 1
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	146.71kB (1833887 bits)
Date Submitted	2007-05-29 00:00:00
Date Available	2007-05-31 00:00:00
Creation Date	2007-05-24 22:39:52
Producing Software	Microsoft® Office Word 2007
Document Lastmod	2007-05-24 22:39:52
Document Title	USERS MANUAL 1
Document Creator	Microsoft® Office Word 2007
Document Author:	Fredric Newberg

Document No. TR0153 Rev D2
EnRoute50x/51x
User’s Guide
Rev. D2
Communicate Without Boundaries
Tranzeo Wireless Technologies Inc.
19473 Fraser Way, Pitt Meadows, BC, Canada V3Y 2V4
www.tranzeo.com
technical support email: support@tranzeo.com
EnRoute50x/51x User’s Guide
Tranzeo, the Tranzeo logo and EnRoute500 are trademarks of Tranzeo Wireless Technologies Inc.. All rights
reserved.
All other company, brand, and product names are referenced for identification purposes only and may be
trademarks that are the properties of their respective owners.
Copyright © 2007, Tranzeo Wireless Technologies Inc..
TR0153 Rev. D2
EnRoute50x/51x User’s Guide
FCC Notice to Users and Operators
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) This device must
accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for Class B Digital Device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures.
Reorient or relocate the receiving antenna
Increase the separation between the equipment and receiver
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected
Consult the dealer or an experienced radio/TV technician for help
To reduce potential radio interference to other users, the antenna type and its gain should be
so chosen that the equivalent isotropically radiated power (EIRP) is not more than that
required for successful communication.
The antenna(s) used for this transmitter must be installed to provide a separation distance of at
least 14cm from all persons.
Any changes or modification to said product not expressly approved by Tranzeo
Wireless Technologies Inc. could void the user's authority to operate this device.
The Tranzeo EnRoute500 Mesh Router must be installed by a trained professional,
value added reseller, or systems integrator who is familiar with RF cell planning
issues and the regulatory limits defined by the FCC for RF exposure, specifically
those limits outlined in sections 1.1307.
TR0153 Rev. D2
EnRoute50x/51x User’s Guide
Table of Contents
1.1
1.2
1.3
1.4
1.5
1.5.1
1.5.2
1.6
1.6.1
1.6.2
Working with the EnRoute500 ........................................................................... 8
EnRoute500 Variants ............................................................................................8
EnRoute500 Capabilities .......................................................................................8
Network Topology .................................................................................................9
Network Terminology .......................................................................................... 10
EnRoute500 Interfaces ....................................................................................... 10
Ethernet and PoE ............................................................................................... 11
Antennas ............................................................................................................ 12
Deployment Considerations ................................................................................ 12
Mesh channel selection ...................................................................................... 12
AP channel selection .......................................................................................... 13
2.1
2.2
2.3
2.4
2.4.1
2.4.2
2.4.3
2.4.4
2.5
2.5.1
2.5.2
2.5.3
2.5.4
2.5.5
2.5.6
2.5.7
2.5.8
2.5.9
2.5.10
2.5.11
2.5.12
2.5.13
2.5.14
2.5.15
2.5.16
Using the Command Line Interface ................................................................ 14
Accessing the CLI ............................................................................................... 14
User Accounts ..................................................................................................... 15
CLI Interfaces ...................................................................................................... 16
CLI Features ....................................................................................................... 16
Control of the Cursor .......................................................................................... 16
Cancel a Command ........................................................................................... 17
Searching the Command History ....................................................................... 17
Executing a Previous Command ........................................................................ 17
CLI Commands ................................................................................................... 17
„?‟ command ....................................................................................................... 17
„whoami‟ command ............................................................................................ 17
„help‟ command .................................................................................................. 18
„show‟ command ................................................................................................ 18
„use‟ command ................................................................................................... 19
„set‟ command .................................................................................................... 20
„get‟ command .................................................................................................... 21
„list‟ command .................................................................................................... 22
„ping‟ command .................................................................................................. 22
„ifconfig‟ command ............................................................................................. 23
„route‟ command ................................................................................................. 23
„clear‟ command ................................................................................................. 23
„history‟ command .............................................................................................. 24
„!‟ command ........................................................................................................ 25
„exit‟ command ................................................................................................... 26
„quit‟ command ................................................................................................... 26
3.1
3.2
3.3
Using the Web Interface .................................................................................. 27
Accessing the Web Interface............................................................................... 27
Configuration Overview Page .............................................................................. 28
Setting Parameters ............................................................................................. 29
TR0153 Rev. D2
EnRoute50x/51x User’s Guide
3.4
3.5
Help Information .................................................................................................. 30
Rebooting ............................................................................................................ 30
Initial Configuration of an EnRoute500 .......................................................... 32
5.1
5.2
5.3
5.4
5.5
Configuration Profile Management ................................................................. 34
Saving the Current Configuration ........................................................................ 34
Load a Configuration Profile ................................................................................ 35
Delete a Configuration Profile ............................................................................. 35
Downloading a Configuration Profile from a Node .............................................. 36
Uploading a Configuration Profile to a Node ....................................................... 37
6.1
6.2
6.3
6.4
6.5
6.6
6.7
6.8
6.9
6.10
6.11
System Settings ............................................................................................... 38
User Passwords .................................................................................................. 38
Operating Scheme .............................................................................................. 39
Mesh / Node ID ................................................................................................... 40
Mesh Prefix ......................................................................................................... 41
LAN Prefix ........................................................................................................... 42
DNS / Domain Settings ....................................................................................... 43
DNS Proxy Configuration .................................................................................... 44
NetBIOS Server .................................................................................................. 45
Location............................................................................................................... 46
Certificate Information ......................................................................................... 47
CLI timeout .......................................................................................................... 48
7.1
7.2
7.3
7.4
7.5
7.6
7.7
Mesh Radio Configuration............................................................................... 49
Channel ............................................................................................................... 49
Service Set Identifier (SSID) ............................................................................... 50
Encryption ........................................................................................................... 51
Transmit Power ................................................................................................... 52
RSSI Threshold Levels ....................................................................................... 52
IP Configuration .................................................................................................. 53
Neighbor Status .................................................................................................. 54
8.1
8.1.1
8.1.2
8.1.3
8.1.4
8.2
8.2.1
8.2.2
Ethernet Interface Configuration .................................................................... 55
IP Configuration for Repeater Nodes and Their Clients ...................................... 55
Ethernet Client Device Address Space .............................................................. 55
Ethernet Interface IP Address ............................................................................ 58
IP Configuration of Client Devices via DHCP ..................................................... 58
Manual IP Configuration of Client Devices ......................................................... 59
IP Configuration for Gateway Nodes ................................................................... 59
DHCP ................................................................................................................. 60
Manual IP Configuration ..................................................................................... 61
9.1
9.2
Access Point (AP) Configuration .................................................................... 63
Access Point Interfaces ....................................................................................... 63
Enabling and Disabling Access Points ................................................................ 64
TR0153 Rev. D2
EnRoute50x/51x User’s Guide
9.3
9.4
9.5
9.6
9.6.1
9.6.2
9.6.3
9.7
9.8
9.8.1
9.8.2
9.8.3
9.9
Access Point Client Device Address Space ........................................................ 64
Channel ............................................................................................................... 66
ESSID ................................................................................................................. 67
IP Configuration for Nodes and Their Clients ...................................................... 68
Access Point IP Address .................................................................................... 69
IP Configuration of Clients Devices via DHCP ................................................... 69
Manual IP Configuration of Client Devices ......................................................... 69
Client Devices ..................................................................................................... 70
Encryption and Authentication............................................................................. 70
WEP Encryption ................................................................................................. 71
WPA Pre-Shared Key Mode (WPA-PSK) ........................................................... 72
WPA EAP Mode ................................................................................................. 73
Transmit Power ................................................................................................... 74
10
10.1
10.2
10.2.1
10.2.2
Client DHCP Configuration.............................................................................. 76
Using Local DHCP Servers ................................................................................. 76
Using a Centralized DHCP Server ...................................................................... 79
Configuring the EnRoute500s ............................................................................ 79
Configuring the Central DHCP Server ................................................................ 82
11
11.1
11.2
11.3
Connecting an EnRoute500 Gateway to a WAN ............................................ 84
Manual Configuration .......................................................................................... 84
Network Address Translation (NAT) .................................................................... 84
VPN Access to a Mesh Gateway ........................................................................ 86
12
12.1
12.2
12.3
12.4
12.4.1
12.4.2
Controlling Access to the EnRoute500 .......................................................... 88
Firewall ................................................................................................................ 88
Gateway Firewall ................................................................................................. 89
Blocking Client-to-Client Traffic ........................................................................... 90
Access Control Lists (ACLs)................................................................................ 92
Access Point Access Control Lists (ACLs) ......................................................... 92
Mesh ACL .......................................................................................................... 93
13
13.1
13.2
13.3
Quality of Service (QoS) Configuration .......................................................... 94
Priority Levels ...................................................................................................... 94
Rate Limiting ....................................................................................................... 97
Rate Reservation ................................................................................................ 99
14
14.1
14.2
Enabling VLAN Tagging ................................................................................ 102
Client Interface Configuration ............................................................................ 102
Gateway Configuration ...................................................................................... 103
15
15.1
15.1.1
15.1.2
15.1.3
Integration with Enterprise Equipment ........................................................ 105
Configuring Splash Pages ................................................................................. 105
Enabling Splash Pages .................................................................................... 105
Configuring Splash URLs ................................................................................. 107
Sample HTML Code for Splash Pages ............................................................ 108
TR0153 Rev. D2
EnRoute50x/51x User’s Guide
15.1.4
15.1.5
15.1.6
15.2
Configuring the Authentication Server .............................................................. 109
Trusted MAC Addresses .................................................................................. 110
Bypass Splash Pages for Access to Specific Hosts ......................................... 111
Layer 2 Emulation ............................................................................................. 112
16
16.1
16.2
Firmware Management .................................................................................. 113
Displaying the Firmware Version ....................................................................... 113
Upgrading the Firmware .................................................................................... 113
17
Glossary .......................................................................................................... 114
TR0153 Rev. D2
EnRoute50x/51x User’s Guide
Working with the EnRoute500
Thank you for choosing the Tranzeo EnRoute500 Wireless Mesh Router. The EnRoute500
allows a wireless mesh network to be rapidly deployed with minimal configuration required by
the end user. This user‟s guide presents a wide array of configuration options, but only a
limited number of options have to be configured in order to deploy a mesh network of
EnRoute500s.
1.1
EnRoute500 Variants
There are four EnRoute500 variants available, as shown in Table 1.
Model Number
EnRoute500
External AC
Power Connector
No
EnRoute501
Yes
EnRoute510
No
EnRoute511
Yes
Included Antennas
AP 5dBi, Mesh 8.5dBi
AP 5dBi, Mesh
8.5dBi
AP 7.5dBi, Mesh
10.5dBi
AP 7.5dBi, Mesh
10.5dBi
Table 1. EnRoute500 variants
Throughout the manual, “EnRoute500” will be used to collectively refer to this family
of products. Where the functionality of the variants differ, the actual model number
will be used.
1.2
EnRoute500 Capabilities
The EnRoute500 is capable of automatically forming a mesh network that allows devices that
are connected to it, either with a wired or a wireless connection, to communicate with each
other and external networks that are accessed through gateway nodes. The EnRoute500 has
two radios, an 802.11a mesh backhaul radio and an access point radio for 802.11b/g-client
devices. An EnRoute500 will currently support up to four access points (APs), each with
different access and performance settings. It is also possible to connect devices to an
EnRoute500 using an Ethernet connection.
TR0153 Rev. D2
EnRoute50x/51x User’s Guide
Figure 1. EnRoute500 sample network – devices attach to
the EnRoute500 through both wired and wireless connections
1.3
Network Topology
EnRoute500s can be used to create two network topologies: a stand-alone network or an
Internet extension network that attaches to a network with connectivity to the Internet.
Figure 2. Internet extension network
An Internet extension network (shown in Figure 2) is typically used when the goal is to provide
Internet access to a number of clients that connect to the mesh network. Alternatively, this
configuration can be used to provide access for client devices to remote resources on a private
network. The key feature to note is that there is a gateway node that provides access from the
mesh network to an external network.
TR0153 Rev. D2
EnRoute50x/51x User’s Guide
Figure 3. Stand-alone network
In a stand-alone network, as shown in Figure 3, all nodes are configured to operate in the
same mode (repeater mode). This network configuration is suitable for applications where the
clients using the mesh only need to communicate with each other and do not need to access
the Internet or other remote network resources that are not directly connected to the mesh.
1.4
Network Terminology
The following terms will be referred to throughout this manual.
Mesh cluster – a group of two or more EnRoute500 nodes with at least one configured as a
gateway
Mesh cloud – a group of EnRoute500 nodes configured as one or more mesh clusters
Mesh node – a single EnRoute500 node that is part of a mesh network
1.5
EnRoute500 Interfaces
The interfaces available on the EnRoute500 are Ethernet and two radio ports. On the
EnRoute5x1 models, an external AC power port is also present.
TR0153 Rev. D2
10
EnRoute50x/51x User’s Guide
AP radio
port
Mesh radio
port
Power
Ethernet
Figure 4. EnRoute500 interfaces. EnRoute501 shown
Interface
Power (EnRoute 5x1 only)
Mesh radio port
AP radio port
Ethernet
Passive PoE
Description
Power input (100-240VAC 50-60 Hz)
N-type antenna connector for mesh radio
N-type antenna connector for access point radio
10/100 Mbit Ethernet interface
PoE secondary power input (9-28VDC, 12W)
Not compatible with IEEE 802.3af
Table 2. EnRoute500 Interfaces
1.5.1
Ethernet and PoE
The EnRoute500 has a 10/100 Ethernet port that supports passive Power over Ethernet (PoE).
The PoE power injector should supply an input voltage between 9-28VDC and a minimum of
12W. The pinout for the Ethernet interface on the EnRoute500 is provided in Table 3.
TR0153 Rev. D2
11
EnRoute50x/51x User’s Guide
The EnRoute500 is equipped with an auto-sensing Ethernet port that allows both
regular and cross-over cables to be used to connect to it.
Pin
Signal
Tx+
TxRx+
PoE V+
PoE V+
RxGnd
Gnd
Standard Wire Color
White/Orange
Orange
White/Green
Blue
White/Blue
Green
White/Brown
Brown
Table 3. Ethernet port pinout
1.5.2
Antennas
Attach the supplied antennas to the mesh and access point (AP) radio ports on the
EnRoute500. The antennas used for the two radios are band-specific and therefore it is
important to correctly match the antennas with the radio ports.
1.6
Deployment Considerations
The EnRoute500‟s radios operate in the unlicensed 2.4 GHz and 5.8 GHz ISM bands. It is
possible that there will be other devices operating in these bands that will interfere with the
EnRoute500‟s radios. Interference from adjacent EnRoute500s can also degrade performance
if the EnRoute500s are not configured properly.
It is advisable to carry out a site survey prior to installation to determine what devices are
operating in the two bands that the EnRoute500 uses. To detect the presence of other 802.11
devices, a tool such as Netstumbler (http://www.netstumbler.com/downloads/) can be used. A
spectrum analyzer can be used for further characterization of interference in the band.
1.6.1
Mesh channel selection
The mesh radio channel must be the same for all EnRoute500s in a given mesh cluster.
Adjacent mesh clusters will get a performance benefit if they are on different channels as the
clusters will not interfere with each other. The 802.11a channels that the EnRoute500 mesh
radio can be configured to use are all non-overlapping.
TR0153 Rev. D2
12
EnRoute50x/51x User’s Guide
1.6.2
AP channel selection
The access point radio channels used by the EnRoute500s in a mesh cluster may differ. It is
advisable to use different access point channels for adjacent mesh nodes to reduce
interference.
However, it may be more important to select the access point channel based on the presence
of other 802.11 devices in the area rather than configuring it to be different than that of an
adjacent EnRoute500. A site survey should be conducted to determine which access point
channel will provide the best performance.
Some of the 802.11b/g channels that the EnRoute500 access point radio can be configured to
use are overlapping. Only channels 1, 6, and 11 are non-overlapping.
TR0153 Rev. D2
13
EnRoute50x/51x User’s Guide
Using the Command Line Interface
All configurable EnRoute500 parameters can be accessed with a Command Line Interface
(CLI).
The CLI allows you to:
Modify and verify all configuration parameters
Save and restore device configurations
Reboot the device
Upgrade the firmware
2.1
Accessing the CLI
The EnRoute500‟s command-line interface (CLI) is accessible through the device‟s network
interfaces using an SSH client. Any of the network interfaces can be used to establish the SSH
connection to the EnRoute500. However, connecting through the Ethernet port is
recommended for devices that have not previously been configured.
The EnRoute500 has a dedicated configuration interface that is accessible via the Ethernet
port. This interface is present regardless of the EnRoute500‟s standard Ethernet interface
configuration. The IP address and netmask of this interface are provided in Table 4.
Since the configuration IP address (shown in Table 4) is the same for all
EnRoute500s, you should not simultaneously connect multiple EnRoute500s to a
common LAN and attempt to access them using the configuration IP address.
Parameter
IP address
Netmask
Protocol
User name
Default password
Setting
169.254.253.253
255.255.0.0
SSH v2
admin
mesh
Table 4. EnRoute500 Ethernet configuration interface settings
To use this interface:
1. Configure a computer with an IP address on the 169.254.0.0 subnet
2. Connect the PC to the EnRoute500 using an Ethernet cable. A standard or cross-over
cable will work.
TR0153 Rev. D2
14
EnRoute50x/51x User’s Guide
3. Login to the node using an SSHv2-capable client application with the credentials
provided in Table 4.
Windows XP does not include an SSH client application. You will need to install a
3rd-party
client
such
as
SecureCRT
from
Van
Dyke
software
(http://www.vandyke.com/products/securecrt) or the free PuTTY SSH client
(http://www.putty.nl/) to connect to an EnRoute500 using SSH.
If you are configuring multiple EnRoute500s with the same computer in rapid
succession, it may be necessary to clear the ARP cache since the IP addresses for
the EnRoute500s will all be the same, but the MAC addresses will vary. The
following commands can be used to clear the ARP cache
Windows XP (executed in a command prompt window)
arp -d *
to clear the entire cache, or
arp -d 169.254.253.253
to just clear the EnRoute500 entry
Linux
arp -d 169.254.253.253
When you log in to the node, the CLI will present a command prompt. The shell timeout is
displayed above the login prompt. The CLI will automatically log out a user if a session is
inactive for longer than the timeout period. Section 6.11 describes how to change the timeout
period.
Shell timeout: 3 minutes.
Press '?' for help..
2.2
User Accounts
There are two user accounts for accessing the EnRoute500: „admin‟ and „monitor‟. With the
„admin‟ account all parameters can be set and viewed. The „monitor‟ account only allows users
to view a subset of the parameters available. Parameters that affect access to the network,
such as encryption keys, are not viewable by the „monitor‟ user. The only parameter that can
TR0153 Rev. D2
15
EnRoute50x/51x User’s Guide
be set by the „monitor‟ user is the shell timeout (see section 6.10). The passwords for both
users can only be set by the „admin‟ user. The procedure for changing passwords is described
in section 6.1.
2.3
CLI Interfaces
The CLI provides the user with a number of interfaces that contain related parameters and
controls. Some of these interfaces are actual hardware interfaces, such as Ethernet, while
others are virtual interfaces that contain a set of related parameters.
The available interfaces are:
mesh0 – controls for the mesh radio
wlan1, wlan2, wlan3, wlan4 – controls for the APs supported by the EnRoute500
eth0 – controls for the Ethernet interface
firewall – controls firewall settings for client device, mesh node and mesh network access
qos – controls Quality of Service (QoS) settings
version – displays version information for the installed firmware
system – system settings
The currently selected interface is shown as part of the command prompt. For example, when
the mesh interface is selected, the command prompt will be
mesh0>
After logging in, no interface is selected by default. Before setting or retrieving any parameters,
an interface must be selected.
2.4
CLI Features
The CLI has a number of features to simplify the configuration of the EnRoute500.
2.4.1
Control of the Cursor
The cursor can be moved to the end of the current line with Ctrl+E. Ctrl+A moves it to the
beginning of the line.
TR0153 Rev. D2
16
EnRoute50x/51x User’s Guide
2.4.2
Cancel a Command
Ctrl+C cancels the input on the current command line and moves the cursor to a new, blank
command line.
2.4.3
Searching the Command History
The command history can be searched by pressing Ctrl+R and entering a search string. The
most recently executed command that matches the string entered will be displayed. Press
„Enter‟ to execute that command.
2.4.4
Executing a Previous Command
By using the up and down arrow keys you can select previously executed commands. When
you find the command you wish to execute, you can either edit it or press „Return‟ to execute it.
2.5
CLI Commands
The usage of all CLI commands is explained in the following subsections. The command
syntax used is
command 
command [optional argument]
2.5.1
‘?’ command
Syntax
Description
Pressing „?‟ at any time in the CLI will display a help menu that provides an
overview of the commands that are described in this section. It is not
necessary to press „Enter‟ after pressing „?‟.
2.5.2
‘whoami’ command
Syntax
whoami
Description
Displays the name of the user you are logged in as.
TR0153 Rev. D2
17
EnRoute50x/51x User’s Guide
2.5.3
‘help’ command
help [command|parameter]
Syntax
where [command] is one of the CLI commands or [parameter] is a
parameter in the currently selected interface.
Description
When no argument follows the help command, a help menu showing a list
of available commands is displayed. When a command is supplied as the
argument, a help message for that particular command is displayed. When
a parameter in the current interface is specified as the argument, help
information for it is displayed.
Example
help get
will display the help information for the „get‟ command. With the „sys‟
interface selected
sys> help scheme
displays help information about that „scheme‟ parameter, as shown below
scheme : wireless node type
2.5.4
‘show’ command
Syntax
show
Description
Displays all available interfaces. An interface in this list can be selected
with the „use‟ command.
TR0153 Rev. D2
18
EnRoute50x/51x User’s Guide
2.5.5
‘use’ command
Syntax
use 
where  is one of the EnRoute500‟s interfaces. A complete list of
interfaces is available with the „show‟ command.
Description
Selects an interface to use. By selecting an interface you can view and
modify the parameters associated with the interface.
Example
use mesh0
will select the backhaul mesh radio interface and change the CLI prompt to
mesh0>
to reflect the interface selection.
TR0153 Rev. D2
19
EnRoute50x/51x User’s Guide
2.5.6
‘set’ command
Syntax
set =
where  is the parameter being set and  is the value it
is being set to.
Description
Sets a configuration parameter. Note that is only possible to set the
parameters for the currently selected interface. If the value of the
parameter contains spaces, the value must be surrounded by double
quotes (“ “).
If a valid 'set' command is entered, it will output its result and any effects on
other parameters. If changes are made to attributes of other interfaces as a
result of changing the parameter, these attributes are preceded by a '/' to
signify that they are in another interface.
Changing certain parameters will require the node to be rebooted.
Example
With the „sys‟ interface selected
set id.node=2
will set the node ID to 2, while
set id.mesh=1
will have an impact on a larger number of parameters as can be seen in
the output below.
id.mesh
private.nets.default
/mesh0.routes.static
splash.local_network
/mesh0.cellid
/mesh0.ip.address
Reboot needed.
"172.29.0.0/16 10.1.0.0/16"
224.0.0.0/4,10.1.0.0/16
"172.29.1.0/24 10.1.0.0/16"
00:05:88:01:0a:01
172.29.1.7
Note that changes were made to variables in the „mesh0‟ interface, as
indicated by the „/‟ at the beginning of those lines.
TR0153 Rev. D2
20
EnRoute50x/51x User’s Guide
2.5.7
‘get’ command
Syntax
get 
where  is the parameter whose value is being fetched.
Description
Gets the value of one or more configuration parameters for the currently
selected interface. The „*‟ character can be used to specify wildcard
characters. This allows multiple values to be fetched with a single
command.
Example
With the „sys‟ interface selected
get id.node
will return the node‟s ID, while
get id.*
will return all parameters that begin with „id.‟
sys.id.lanprefix = 10
sys.id.mesh = 4
sys.id.meshprefix = 172.29
sys.id.node = 7
TR0153 Rev. D2
21
EnRoute50x/51x User’s Guide
2.5.8
‘list’ command
Syntax
list
Description
Lists all parameters for the selected interface
Example
With the „firewall‟ interface selected
list
will display
firewall.gateway.enable : prevent uninitiated incoming connections
past the gateway?
firewall.node.allowc2c.eth0 : allow clients to see each other if
.role=access
firewall.node.allowc2c.wlan1 : allow clients to see each other if
.role=access
firewall.node.allowc2c.wlan2 : allow clients to see each other if
.role=access
firewall.node.allowc2c.wlan3 : allow clients to see each other if
.role=access
firewall.node.allowc2c.wlan4 : allow clients to see each other if
.role=access
firewall.node.enable : firewall enabled? if not, nothing else
here matters.
firewall.node.tcp.allow.dest : tcp dest ports (space separated)
to allow to this node
firewall.node.tcp.allow.source
tcp
source
ports
(space
separated) to allow to this node
firewall.node.udp.allow.dest : udp dest ports (space separated)
to allow to this node
firewall.node.udp.allow.source
udp
source
ports
(space
separated) to allow to this node
2.5.9
‘ping’ command
Syntax
ping 
Description
Pings a remote network device. Halt pinging with Ctrl+C
Example
ping 172.29.1.1
TR0153 Rev. D2
22
EnRoute50x/51x User’s Guide
2.5.10
‘ifconfig’ command
Syntax
ifconfig 
Description
Displays information, such as IP address and MAC address, for the
specified network interface.
Example
ifconfig wlan1
will display
wlan1
2.5.11
Link encap:Ethernet HWaddr 00:15:6D:52:01:FD
inet addr:10.2.10.1 Bcast:172.29.255.255 Mask:255.255.0.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:2434 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:233128 (227.6 Kb)
‘route’ command
Syntax
route
Description
Displays the current route table.
2.5.12
‘clear’ command
Syntax
clear
Description
Clears the screen
TR0153 Rev. D2
23
EnRoute50x/51x User’s Guide
2.5.13
‘history’ command
Syntax
history
Description
Shows the command history since the node was last rebooted
Example
After switching to the „wlan1‟ interface, inspecting the ESSID setting, and
then changing it
history
will display
1: use wlan1
2: get essid
3: set essid=new_ap_essid
TR0153 Rev. D2
24
EnRoute50x/51x User’s Guide
2.5.14
‘!’ command
Syntax
!
!
!!
Description
Executes a previously-executed command based either on a command
history number or matching a string to the start of a previously-executed
command. Note that there is no space between the „!‟ and the argument.
The „history‟ command shows the command history, with a number
preceding each entry in the command history. Use this number as an
argument to the „!‟ command to execute that command from the history.
When a string is provided as an argument to the „!‟ command, the string will
be matched against the beginning of previously-executed commands and
the most recently executed command that matches will be executed.
Use „!!‟ to execute the last command again.
Example
If the command history is as follows
1:
2:
3:
4:
5:
use
get
set
use
set
wlan1
essid
essid=new_ap_essid1
wlan2
essid=new_ap_essid2
the command
!1
will execute
use wlan1
The command
!use
will execute
use wlan2
TR0153 Rev. D2
25
EnRoute50x/51x User’s Guide
2.5.15
‘exit’ command
Syntax
exit
Description
Terminates the current CLI session and logs out the user
2.5.16
‘quit’ command
Syntax
quit
Description
Terminates the current CLI session and logs out the user
TR0153 Rev. D2
26
EnRoute50x/51x User’s Guide
Using the Web Interface
The EnRoute500 has a web interface accessible through a browser that can also be used to
configure the node and display status parameters.
3.1
Accessing the Web Interface
You can access the web interface by entering one of the node‟s IP addresses preceded by
“https://” in the URL field of a web browser (see section 2.1 for a description of how to access
an unconfigured node using its Ethernet interface). When you enter this URL, you will be
prompted for a login and password. The login and password used for the web interface is the
same as for the CLI (see Table 4 in section 2.1).
The node IP must be preceded by “https://”, not “http://”, to access the web interface
Figure 5. Login window for web interface
Since the certificate used in establishing the secure link to the node has not been signed by a
Certification Authority (CA), your browser will most likely display one or more warnings similar
to those shown below. These warnings are expected and can be disregarded.
TR0153 Rev. D2
27
EnRoute50x/51x User’s Guide
Figure 6. Certificate warning
3.2
Configuration Overview Page
A configuration overview page is loaded by default after the login process has been completed.
This page contains the following information
System type (gateway or repeater)
System uptime
Interface IP addresses
VLAN status and ID for all interfaces
Mesh interface channel and ESSID
Access point status, channel, ESSID, and encryption type
Ethernet interface use (client access or backhaul)
Firmware version
To access the status page from any other page in the web interface, click on the “Status”
button on the left side of the page.
TR0153 Rev. D2
28
EnRoute50x/51x User’s Guide
Figure 7. Sample status page
3.3
Setting Parameters
Many of the web interface pages allow you to set EnRoute500 operating parameters. Each
page that contains settable parameters has a “Save Changes” button at the bottom of the
page. When you have made your changes on a page and are ready to commit the new
TR0153 Rev. D2
29
EnRoute50x/51x User’s Guide
configuration, click on the “Save Changes” button. It typically takes a few seconds to save the
changes, after which the page will be reloaded.
For the changes to take effect, the node must be rebooted. After a change has been
committed, a message reminding the user to reboot the node will be displayed at the top of the
screen.
Figure 8. Sample page showing "Save Changes" button and message prompting the user to reboot
3.4
Help Information
Help information is provided on most web GUI pages. The help information is shown on the
right-hand side of the page. The help information can be hidden by clicking on the „Hide Help‟
link inside the help frame. When help is hidden, it can be displayed by clicking on the „Show
help‟ link.
3.5
Rebooting
Click on the “Reboot” link on the left of the page and then click on the “Reboot Now” button to
reboot the node. Any changes made prior to rebooting will take effect following completion of
the boot process.
TR0153 Rev. D2
30
EnRoute50x/51x User’s Guide
Figure 9. Rebooting the node
TR0153 Rev. D2
31
EnRoute50x/51x User’s Guide
Initial Configuration of an EnRoute500
This user‟s guide provides a comprehensive overview of all of the EnRoute500‟s features and
configurable parameters. However, it is possible to deploy a network of EnRoute500s while
only changing a limited number of parameters. The list below will guide you through a minimal
configuration procedure that prepares a network of EnRoute500s for deployment.
Change the ‘admin’ and ‘monitor’ passwords.
The default passwords should be changed to prevent
unauthorized access to the node.
See section 6.1
Set the operating scheme for the node
Most nodes will be configured as repeaters, with at least
one node per mesh cluster configured as a gateway.
See section 6.2
Set the node and mesh IDs
The node and mesh IDs uniquely identify a node and
determine which mesh cluster it is part of.
See section 6.3
Set the DNS servers
Specify DNS servers to allow hostnames to be resolved.
See section 6.6
Set the mesh radio channel
The mesh radios on all nodes in a mesh cluster must be
set to operate on the same channel.
See section 7.1
Set the mesh ESSID
Set the mesh interface ESSID to a common value for all
nodes in a mesh cluster. It should be different than the
ESSID for any adjacent mesh clusters.
See section Error!
Reference source
not found.
Set the AES encryption key for the mesh
Change the default AES encryption key to prevent
unauthorized access to the mesh. The mesh encryption
key must be the same for all nodes in a mesh cluster.
See section 7.3
Set the mesh radio transmit power
Set the mesh power to the maximum allowed value to
achieve the best possible connectivity between mesh
nodes.
See section 7.4
TR0153 Rev. D2
32
EnRoute50x/51x User’s Guide
After these settings have been changed, the EnRoute500s will be able to form a mesh cluster
and you will be able to configure the nodes from a central location. This minimal configuration
must be performed prior to deployment, but all other configuration can be carried out after
deployment.
To simplify initial configuration, the web GUI has a page that allows the user to change all the
parameters listed in this section on a single page. This page can be accessed by clicking on
the „Minimal configuration‟ link that is present on the left-hand side of all web GUI pages.
Figure 10. Initial configuration web page
TR0153 Rev. D2
33
EnRoute50x/51x User’s Guide
Configuration Profile Management
Configuration profiles describe an EnRoute500‟s configuration state and can be created to
simplify the provisioning and management of nodes. The EnRoute500 supports the following
configuration profile-related tasks:
Saving the current configuration as a configuration profile
Applying a configuration profile stored on the node
Downloading a configuration profile stored on the node to a computer
Uploading a configuration profile from a computer to the node
Deleting a configuration profile stored on the node
Currently configuration profile management is only supported via the web interface.
5.1
Saving the Current Configuration
The current configuration can be saved on the “Save” tab on the “Profile Management“ page.
Enter a profile name or select an existing profile name from the list of existing configurations,
and then click on “Save Profile”. The saved profile is stored locally on the node and will appear
in the “Existing profiles” text box. Use the “Download from Node” tab to download it to a
different device.
Figure 11. Save a configuration profile
TR0153 Rev. D2
34
EnRoute50x/51x User’s Guide
5.2
Load a Configuration Profile
A configuration stored on the node can be loaded on the “Load” tab on the “Profile
Management“ page. This profile must either have been saved earlier or uploaded to the node.
Choose a profile name from the “Existing Profiles” box and then click on “Load Profile”. It is
necessary to reboot the node for the loaded profile settings to take effect.
Figure 12. Load a configuration profile
5.3
Delete a Configuration Profile
A locally-stored configuration profile can be deleted using the “Delete” tab on the “Profile
Management“ page. Choose a profile to delete from the profile drop-down box on the page and
then click on “Delete Profile”.
TR0153 Rev. D2
35
EnRoute50x/51x User’s Guide
Figure 13. Deleting a configuration profile
5.4
Downloading a Configuration Profile from a Node
A configuration profile can be download from a node using the “Download from node” tab on
the “Profile Management“ page. The existing configuration profiles are listed on this page.
Click on the one that is to be downloaded to your computer and you will be given the option to
specify where the profile should be saved on the host computer.
Figure 14. Downloading a configuration profile from a node
TR0153 Rev. D2
36
EnRoute50x/51x User’s Guide
5.5
Uploading a Configuration Profile to a Node
A configuration profile can be uploaded to a node using the “Upload to node” tab on the
“Profile Management“ page. Use the “Browse” button to select a profile file on your host
computer for upload to the node. Alternatively, enter the file name by hand in the text box
adjacent to the “Browse” button. Click on the “Upload Profile” button to upload the selected file
to the node.
Figure 15. Uploading a configuration profile to a node
TR0153 Rev. D2
37
EnRoute50x/51x User’s Guide
System Settings
This section describes settings that are applicable to the overall operation of the EnRoute500,
but are not related directly to a particular interface.
6.1
User Passwords
The passwords for the „admin‟ and „monitor‟ users are configurable. The default password for
both accounts is „mesh‟.
CLI
The passwords for the „admin‟ and „monitor‟ users can be set using the „password.admin‟ and
„password.monitor‟ parameters in the „sys‟ interface. The passwords will not be displayed when
using the „get‟ command with these parameters. Note that the „monitor‟ account password can
only be changed by an „admin‟ user. The example below shows how to set the „admin‟
password using the CLI.
> use sys
sys> set password.admin=newpass
Web GUI
The passwords can be changed via the web interface using the “Passwords” tab on the
“System Parameters” page. The passwords can be changed independently – if only one
password is modified, the other password will remain unchanged.
Figure 16. Passwords page
TR0153 Rev. D2
38
EnRoute50x/51x User’s Guide
6.2
Operating Scheme
The operating scheme determines a node‟s role in the mesh network. Typically one of two
configurations will be used in a network:
All EnRoute500s will be configured as repeater nodes to create a stand-alone mesh cluster
At least one of the EnRoute500s in a mesh cluster will be configured as a gateway node,
with the remaining nodes configured either as gateways or repeaters. The gateway nodes
are connected to an external network using the nodes‟ Ethernet interfaces. This network
configuration will create an Internet extension network.
Mode
Repeater
Gateway
Description
The EnRoute500 will function as a relay in the mesh network.
Client devices can connect to the node using both wired (10/100
Ethernet) and wireless (built-in APs) interfaces. The node can
provide IP addresses to clients on both the wired and wireless
interfaces.
The EnRoute500 will function as a relay in the mesh network and
a gateway to a WAN. Client devices can only connect to the
node using the wireless (built-in APs) interfaces. The node can
provide IP addresses to clients on the wireless interface.
Ethernet interface
Client devices can connect to
it. IP addresses can be
provided to client devices
using DHCP or be manually
configured.
Used to connect the mesh
cluster to a larger network.
Will expect to be provided an
IP address by a DHCP server
or have a static IP address
assigned to it.
Table 5. EnRoute500 operating schemes
CLI
The EnRoute500‟s operating scheme is set with the „scheme‟ parameter in the „sys‟ interface.
Valid values are „apgateway‟ and „aprepeater‟. For example, set the operating scheme to
gateway mode with:
> use sys
sys> set scheme=apgateway
Web GUI
The operating scheme can be set via the web interface using the “System” tab on the “System
Parameters” page.
TR0153 Rev. D2
39
EnRoute50x/51x User’s Guide
Figure 17. Setting the operating scheme
6.3
Mesh / Node ID
An EnRoute500 must be assigned mesh and node IDs before it is deployed as part of a mesh
cluster. Together, these values uniquely identify a node within a mesh cluster and no two
nodes in a cluster are allowed to have the same node ID.
The mesh ID must be the same for all nodes in a cluster The range of valid mesh IDs is 0
through 254.
The node ID is part of the node‟s IP address as shown in Figure 18. The allowable range for
node IDs is 1 through 254.
172.29 . 12 . 107
Mesh prefix
Mesh ID Node ID
Figure 18. EnRoute500 mesh interface IP address
CLI
The mesh ID is set with the „id.mesh‟ parameter in the „sys‟ interface as shown below.
> use sys
sys> set id.mesh=12
The node ID is set with the „id.node‟ parameter in the „sys‟ interface as shown below.
TR0153 Rev. D2
40
EnRoute50x/51x User’s Guide
> use sys
sys> set id.node=107
Web GUI
The mesh and node IDs can be set via the web interface using the “System” tab on the
“System Parameters” page.
Figure 19. Setting the mesh and node IDs
6.4
Mesh Prefix
The mesh prefix parameter sets the first two octets of a node‟s mesh interface IP address. It
must be set the same for all nodes in a given mesh cluster. The allowed range of values is
172.16 through 172.29.
It is recommended that the mesh prefix is not changed from its default value 172.29.
CLI
The mesh prefix is set with the „id.meshprefix‟ parameter in the „sys‟ interface as shown in the
example below.
> use sys
sys> set id.meshprefix=172.29
TR0153 Rev. D2
41
EnRoute50x/51x User’s Guide
Web GUI
The mesh prefix can be set via the web interface using the “Mesh” tab on the “Wireless
Interfaces” page.
Figure 20. Setting the mesh prefix
6.5
LAN Prefix
A Class C subnet is shared between a EnRoute500‟s access point and Ethernet interfaces.
The subnet address space is based on the mesh ID, node ID, and LAN prefix. The suggested
values for the LAN prefix are 10 and 192. The LAN prefix must be the same for all nodes in a
mesh cluster.
10 . 12 . 107 . 0
LAN prefix
Mesh ID
Node ID
Figure 21. Subnet address structure
By default the subnet is split between a node‟s interfaces as shown in Table 6. See sections
8.1.4 and 9.6.3 for instructions on how to adjust how the subnet is segmented between
interfaces.
TR0153 Rev. D2
42
EnRoute50x/51x User’s Guide
Interface
wlan1
wlan2
wlan3
wlan4
eth0
Interface address
subnet.1
subnet.129
subnet.161
subnet.193
subnet.225
Broadcast address
subnet.127
subnet.159
subnet.191
subnet.223
subnet.255
Client address range
subnet.2-126
subnet.130-158
subnet.162-190
subnet.194-222
subnet.226-254
subnet = ..
Table 6. Default subnet segmentation between interfaces
CLI
The LAN prefix is set with the „id.lanprefix‟ parameter in the „sys‟ interface as shown in the
example below.
> use sys
sys> id.lanprefix=10
Web GUI
The LAN prefix can be set via the web interface using the “System” tab on the “System
Parameters” page (see Figure 19).
6.6
DNS / Domain Settings
At least one DNS server must be specified for a node to be able to resolve host names. This
DNS server is also provided to client devices that acquire an IP address from the local DHCP
server on a node.
If a gateway node acquires DNS server information through DHCP, this DNS server
information will overwrite the „dns.servers‟ setting. Note that the DNS server settings will not be
passed to repeater nodes that are in the same mesh cluster that the gateway is serving – you
will need to set this on each of the repeater nodes.
CLI
The DNS server(s) used by the node are specified with the „dns.servers‟ parameter in the „sys‟
interface. To specify multiple DNS servers, list them as a space-delimited string enclosed by
quotes as shown in the example below
> use sys
sys> set dns.servers =”10.5.0.5 192.168.5.5”
TR0153 Rev. D2
43
EnRoute50x/51x User’s Guide
Web GUI
A primary and secondary DNS server can be set via the web interface using the “DNS” tab on
the “System Parameters” page.
Figure 22. Setting the DNS server(s)
6.7
DNS Proxy Configuration
DNS proxy entries can be added to an EnRoute500 to force local resolution of host names to
IP addresses.
CLI
A list of hostname/IP address to be resolved locally can be specified using the „dnsproxy.hosts‟
parameter in the „sys‟ interface. If multiple hostname/IP address entries are specified, they
must be separated by semi-colons, as shown in the example below. DNS proxying must be
explicitly enabled using the „dnsproxy.enable‟ parameter in the „sys‟ interface after the list of
hosts has been specified.
> use sys
sys> set dnsproxy.enable=yes
> use sys
sys> set dnsproxy.hosts=”server1.domain.com=10.0.0.1;server2.domain.com=10.0.0.129”
TR0153 Rev. D2
44
EnRoute50x/51x User’s Guide
Web GUI
DNS proxying can be enabled through the Web GUI as shown in Figure 23. Hostname/IP
address pairs can be added through the web interface as well.
Figure 23. Configuring DNS proxying
6.8
NetBIOS Server
The NetBIOS server parameter is used to define a NetBIOS server IP address that is provided
to client devices by the local DHCP server.
CLI
The NetBIOS server is set with the „netbios.servers‟ parameter in the „sys‟ interface. To specify
multiple NetBIOS servers, list them as a space-delimited string enclosed by quotes as shown
in the example below
> use sys
sys> set netbios.servers =”10.6.0.5 192.168.6.5”
Web GUI
A primary and secondary NetBIOS server can be set via the web interface using the “DNS” tab
on the “System Parameters” page.
TR0153 Rev. D2
45
EnRoute50x/51x User’s Guide
Figure 24. Setting the NetBIOS server(s)
6.9
Location
Two types of node location information can be stored:
Latitude/longitude/altitude
Postal address or description a node‟s location
Note that these values are not automatically updated and must be entered after a node has
been installed. Altitude is in meters. Latitude and longitude must be given in geographic
coordinates, with latitude ranging from -90 to 90 (with negative being south, positive being
north) and longitude ranging from -180 to 180 (with negative being west, positive being east).
CLI
The GPS location of the node can be stored in the following fields in the „sys‟ interface:
sys.location.gps.altitude
sys.location.gps.latitude
sys.location.gps.longitude
For example, you can set the latitude value as follows.
> use sys
sys> set location.gps.latitude=”34.01”
TR0153 Rev. D2
46
EnRoute50x/51x User’s Guide
A description of the node‟s location can be stored in the „location.postal‟ field in the „sys‟
interface. For example, you can set the location value as shown below.
> use sys
sys> set location.postal=”Light post near 123 Main St., Anytown, CA”
Web GUI
The location information can be set via the web interface using the “Location” tab on the
“System Parameters” page.
Figure 25. Setting location information
6.10
Certificate Information
A certificate for use with splash pages and the web interface is locally generated on the node.
The information embedded in this certificate can be defined by the user. A new certificate is
automatically generated when any of the following parameters are changed.
CLI
The information used in certificate generation can be set using the „organization‟ parameters in
the „sys‟ interface. These parameters are:
sys.organization.name –name of organization (must be enclosed in quotes if it contains
spaces)
sys.organization.city – city name (must be enclosed in quotes if it contains spaces)
TR0153 Rev. D2
47
EnRoute50x/51x User’s Guide
sys.organization.state – state name
sys.organization.country – two-letter country abbreviation
Web GUI
The certificate information can be set via the web interface using the “Location” tab on the
“System Parameters” page.
Figure 26. Setting certificate information
6.11
CLI timeout
The CLI will automatically log out a user if the interface has remained inactive for a certain
length of time. The time, in seconds, that a shell must remain inactive before a user is
automatically logged out is set with the „shell.timeout‟ parameter in the „sys‟ interface, as
shown in the example below. The maximum idle time that can be set is 21600 seconds (360
minutes).
> use sys
sys> set shell.timeout=300
TR0153 Rev. D2
48
EnRoute50x/51x User’s Guide
Mesh Radio Configuration
The EnRoute500 has an 802.11a radio dedicated to mesh backhaul traffic. The settings for this
radio are independent of any settings for the radio used for the EnRoute500‟s built-in access
points. The majority of the mesh radio settings must be the same on all nodes in a given mesh
cluster for the nodes to be able to communicate.
Figure 27. Mesh interface parameters
7.1
Channel
The 802.11a radio can be set to operate in the channels listed in Table 7. All these channels
are non-overlapping.
Channel
149
153
157
161
165
Center Frequency (GHz)
5.745
5.765
5.785
5.805
5.825
Table 7. Mesh radio channels and frequencies
TR0153 Rev. D2
49
EnRoute50x/51x User’s Guide
All the nodes in a mesh cluster need to be configured to use the same 802.11a channel.
CLI
The mesh radio channel is set with the „channel‟ parameter in the „mesh‟ interface as shown in
the example below.
> use mesh0
mesh0> set channel=157
Web GUI
The mesh radio channel can be set via the web interface using the “Mesh” tab on the “Wireless
Interfaces” page (see Figure 27).
7.2
Service Set Identifier (SSID)
The Service Set Identifier, or SSID, is used in 802.11 communication to identify a particular
network. It differentiates logical networks that operate on the same radio channel. The mesh
radio SSID for all the nodes in a mesh cluster must be the same. If you have adjacent mesh
clusters where one or more nodes from each cluster are within communication range of each
other, the SSID for the clusters must be different.
The SSID value must be a text string that has a maximum length of 32 characters. It must only
contain alphanumeric characters, spaces, dashes (“-“), and underscores (“_”). The SSID
setting is case sensitive.
It is possible to hide the mesh SSID by restricting it from being broadcast. You will generally
want the mesh SSID to be hidden, and it is hidden by default.
CLI
The mesh radio SSID is set as shown in the example below. When setting an ESSID that
contains spaces, the SSID value must be enclosed by quotes. The quotes are optional
otherwise.
> use mesh0
mesh0> set essid=”enroute500_mesh”
The broadcast of the SSID can be controlled with the „hide_essid‟ parameter in the „mesh0‟
interface. The example below shows how hiding of the SSID can be enabled.
> use mesh0
mesh0> set hide_essid=yes
TR0153 Rev. D2
50
EnRoute50x/51x User’s Guide
Web GUI
The mesh radio SSID and its broadcast state can be set via the web interface using the “Mesh”
tab on the “Wireless Interfaces” page (see Figure 27).
7.3
Encryption
The mesh radio link can be protected with an encryption key to prevent unauthorized users
from intercepting or spoofing mesh traffic. Each node in a mesh cluster must have the same
encryption key.
CLI
To enable encryption, set the „key‟ parameter in the „mesh0‟ interface. The examples below
illustrate how to set the encryption key. The „key‟ parameter can either be specified as a 16character ASCII string preceded by “s:” or a 32-character hexadecimal string.
Encryption can be enabled using an ASCII key with
> use mesh0
mesh0> set key=”s:abcdefghijklmnop”
or using a hexadecimal key with
> use mesh0
mesh0> set key=”0123456789abcdef0123456789abcdef”
Encryption can be disabled by specifying a blank value as shown below.
> use mesh0
mesh0> set key=
Web GUI
The mesh radio encryption key can be set via the web interface using the “Mesh” tab on the
“Wireless Interfaces” page (see Figure 27). The same encryption key must be entered in both
the “Mesh Key” and “Verify Mesh Key” text boxes for the new key to be accepted.
Only ASCII keys can be entered using the web interface. Unlike the CLI, an ASCII
key should not be preceded by “s:”
TR0153 Rev. D2
51
EnRoute50x/51x User’s Guide
7.4
Transmit Power
The transmit power of the mesh radio is configurable. Increased output power will improve
communication range, but will also extend the interference range of the radios. It is suggested
that the transmit power is initially set to the maximum level for an installation and is then
reduced if it is determined that the transmit power far exceeds the level required to maintain
links. It is also recommended that a common transmit power value is used for all nodes in a
mesh to reduce the likelihood of asymmetric links. The default transmit power is 22dBm.
The mesh radio’s transmit power value must be less than the default value to
be in compliance with FCC regulations. Setting a value greater than the default
power is prevented by the software.
CLI
The example below shows how to set the mesh radio‟s transmit power with the „txpower‟
parameter in the „mesh0‟ interface . Note that the parameter specified in the CLI is not in dBm.
Refer to Table 8 for converting between CLI parameter values and dBm.
> use mesh0
mesh0> set txpower=33
txpower
14
18
22
26
29
33
Output Power (dBm)
10
12
14
16
18
20
22
Table 8. Mesh radio output power settings in the CLI
Web GUI
The mesh radio transmit power can be set via the web interface using the “Mesh” tab on the
“Wireless Interfaces” page (see Figure 27).
7.5
RSSI Threshold Levels
The mesh networking algorithm evaluates link qualities to neighboring mesh nodes and only
considers links with a received signal strength indicator (RSSI) value equal to or greater than
TR0153 Rev. D2
52
EnRoute50x/51x User’s Guide
the „RSSI Join‟ value specified to be usable. The „RSSI Join‟ value is set to 27 by default. This
value reflects the lowest RSSI that will allow the mesh radio to operate at its highest data rate.
It is possible to achieve longer link ranges, at the cost of reduced throughput, by reducing the
„RSSI Join‟ value.
In combination with the „RSSI Join‟ value, the „RSSI Margin‟ value is used to set the RSSI level
at which links are dropped. A link will be considered broken when its RSSI drops below the
„RSSI Join‟ level by the amount specified with „RSSI Margin‟. For example, with an „RSSI Join‟
value of 27 and an „RSSI Margin‟ value of 3, the link will be dropped if the RSSI goes below
24.
CLI
The example below shows how to set the mesh radio‟s RSSI thresholds with the
„fabric.rssi.join‟ and „fabric.rssi.margin‟ parameters in the „mesh0‟ interface .
> use mesh0
mesh0> set fabric.rssi.join=27
> use mesh0
mesh0> set fabric.rssi.margin=3
Web GUI
The mesh radio RSSI thresholds can be set via the web interface using the “Mesh” tab on the
“Wireless Interfaces” page (see Figure 27).
7.6
IP Configuration
The IP address, broadcast address, and netmask associated with the mesh radio interface can
be viewed through the CLI and the web GUI interfaces. It is not possible to directly set these
values though. To change the mesh interface IP settings, the node and mesh ID settings must
be changed (see sections 6.3 and 6.4).
CLI
In the CLI, the mesh IP settings can be viewed with
> use mesh0
mesh0> get ip.address
ip.address = 172.29.2.4
[read-only]
mesh0> get ip.broadcast
ip.broadcast = 172.29.255.255
[read-only]
mesh0> get ip.gateway
ip.gateway =
[read-only]
mesh0> get ip.netmask
ip.netmask = 255.255.0.0
[read-only]
TR0153 Rev. D2
53
EnRoute50x/51x User’s Guide
Web GUI
The mesh radio IP settings are available through the web interface on the “Status” page.
7.7
Neighbor Status
Information on mesh neighbors is provided on the mesh status page of the web GUI,
accessible under the „Status‟ tab on the „Status‟ page. The signal strength of each mesh
neighbor device, it‟s MAC address, its IP address, and the time since data was last received
from it are listed. A sample of the mesh neighbor status page is shown in Figure 28.
The minimum RSSI required for a link to be established and maintained are set with the „RSSI
Join‟ and „RSSI Margin‟ parameters (see section 7.5).
Figure 28. Mesh neighbor status information
TR0153 Rev. D2
54
EnRoute50x/51x User’s Guide
Ethernet Interface Configuration
The function of the Ethernet interface (eth0) depends on the operating scheme that has been
selected (see section 6.2). In repeater mode, the Ethernet interface can be used to connect
client devices to the mesh cluster. In gateway mode, the Ethernet interface is used as a
backhaul interface that connects the mesh cluster to a WAN. Client devices cannot connect
through the Ethernet interface in this mode.
8.1
IP Configuration for Repeater Nodes and Their Clients
When an EnRoute500 is configured as a repeater, client devices can connect to it via the
Ethernet interface to access the mesh network. These client devices can either be assigned
their IP configuration using DHCP or be manually configured.
Figure 29. Wired interface parameters with EnRoute500 in repeater mode
8.1.1
Ethernet Client Device Address Space
The Ethernet interface, when the node is in repeater mode, is assigned a segment of the class
C address space that each node has to share between its client interfaces, which include eth0,
wlan1, wlan2, wlan3, and wlan4. The start address of the address segment and its size can be
set with the IP address range start address and size parameters. The following restrictions are
placed on the address segment configuration:
Each active client interface must be assigned an address segment.
TR0153 Rev. D2
55
EnRoute50x/51x User’s Guide
The IP address range start address („ip.start.requested‟ in the CLI) must be one of the
following values: 1, 33, 65, 97, 129, 161, 193, 225.
The IP address range size („ip.size.requested‟ in the CLI) must be one of the following
values: 31, 63, 127, 255.
The IP address range size and start address must be chosen such that the address
segment does not cross a netmask boundary. Table 9 lists allowed combinations.
The address spaces for enabled interfaces must start at different addresses.
The address spaces for enabled interfaces should not overlap.
ip.start.requested
33
65
97
129
161
193
225
31
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
ip.size.requested
63
127
Yes
Yes
No
No
Yes
No
No
No
Yes
Yes
No
No
Yes
No
No
No
255
Yes
No
No
No
No
No
No
No
Table 9. Allowed address segment start address and size combinations
Each of the enabled interfaces‟ address segments should be configured to avoid overlap with
the other interfaces‟ address segments. In the case where a node is not configured such that
this requirement is met, address spaces will be automatically reduced in size to prevent
overlap.
CLI
In the first example below, the Ethernet interface is set to use the entire class C address space
(this requires that all the other client interfaces, wlan1-4, are disabled). In the second example,
the Ethernet interface is set to use the upper half of the class C address space.
> use eth0
eth0> set ip.start.requested=1
eth0> set ip.size.requested=255
> use eth0
eth0> set ip.start.requested=129
eth0> set ip.size.requested=127
The actual start address and size of a segment are accessible via the „ip.start.actual‟ and
„ip.size.actual‟ parameters.
TR0153 Rev. D2
56
EnRoute50x/51x User’s Guide
Web GUI
The eth0 address segment start address and size can be set via the web interface using the
“DHCP” sub-tab on the “DHCP” tab on the “System Parameters” page (see Figure 30).
Figure 30. ‘eth0’ DHCP and address space settings
TR0153 Rev. D2
57
EnRoute50x/51x User’s Guide
8.1.2
Ethernet Interface IP Address
The EnRoute500‟s Ethernet interface IP address should not be changed directly when it is in
repeater mode. To set the IP address to the desired value, modify the node ID, mesh ID, and
LAN prefix parameters (see sections 6.3 and 6.5).
CLI
You can view the IP settings for the Ethernet interface with the „ip.*‟ parameters in the „eth0‟
interface as shown in the example below.
> use eth0
eth0> get ip.*
ip.address = 10.2.4.225
[read-only]
ip.address_force =
ip.broadcast = 10.2.4.255
[read-only]
ip.broadcast_force =
ip.gateway =
[read-only]
ip.gateway_force =
ip.netmask = 255.255.255.0
[read-only]
ip.netmask_force =
ip.size.actual =
[read-only]
ip.size.requested = 31
ip.start.actual =
[read-only]
ip.start.requested = 225
When the node is in repeater mode, the Ethernet IP settings can be changed by altering the
„id.node‟, „id.mesh‟, and „id.lanprefix‟ parameters in the „sys‟ interface and the
„ip.start.requested‟ parameter in the „eth0‟ interface
Web GUI
The Ethernet IP settings are available through the web interface on the “Status” page. The
Ethernet IP settings can be changed by altering the node ID, mesh ID, and LAN prefix settings
on the “System” parameters tab on the “System Parameters” page.
8.1.3
IP Configuration of Client Devices via DHCP
When configured as a repeater, the EnRoute500 can be set to serve IP addresses to clients on
the Ethernet interface using DHCP. Two distinct modes for providing IP addresses via DHCP
exist. These are described in depth in section 10.
TR0153 Rev. D2
58
EnRoute50x/51x User’s Guide
8.1.4
Manual IP Configuration of Client Devices
The client devices connected via the Ethernet interface that use static IP addresses must have
addresses that are within the subnet of the Ethernet interface.
If the local DHCP server is enabled for the Ethernet interface, IP addresses must be reserved
for statically-configured devices by setting the DHCP reserve parameter. This will reserve the
specified number of IP addresses at the bottom of the IP range for the interface. For example,
if the interface has been assigned the IP address 10.2.4.225, the netmask 255.255.255.224,
and the DHCP reserve value 5, the IP addresses 10.2.4.226 through 10.2.4.230 will be
available for use by statically configured devices. The remaining IP addresses in the
interfaces address space can be assigned by the DHCP server to other client devices.
CLI
The number of IP addresses reserved for statically-configured devices connected to the
Ethernet interface is set with the „dhcp.reserve‟ parameter in the „eth0‟ interface.
Web GUI
The DHCP reserve value can be set via the web interface using the “DHCP” sub-tab on the
“DHCP” tab on the “System Parameters” page (see Figure 30).
8.2
IP Configuration for Gateway Nodes
When an EnRoute500 is configured as a gateway, the Ethernet interface is used to provide
backhaul capability by connecting it to a WAN or directly to the Internet. Clients cannot connect
to the EnRoute500 through the Ethernet interface when operating in this mode. The Ethernet
interface IP address can either be acquired from a DHCP server on the WAN or be set
manually.
TR0153 Rev. D2
59
EnRoute50x/51x User’s Guide
Figure 31. Wired interface parameters with EnRoute500 using wired interface for backhaul
8.2.1
DHCP
When configured as a gateway, the EnRoute500 can be set to obtain an obtain an IP address
for its Ethernet interface using DHCP. To enable the DHCP client mode on the Ethernet
interface, set the value of the Ethernet DHCP role parameter to „client‟. When configured as a
DHCP client, the EnRoute500 will continually attempt to contact a DHCP server until it is
successful.
The DHCP reserve parameter (described in section 6.1.1) has no effect when the
DHCP role parameter is set to „client‟.
To disable Ethernet DHCP client mode, set the DHCP role parameter to „none‟. If DHCP client
mode is disabled, the IP configuration must be carried out manually, as described in the next
section.
CLI
To enable the DHCP client mode on the Ethernet interface, set the value of the „dhcp.role‟
parameter in the „eth0‟ interface to „client‟, as shown in the example below.
> use eth0
eth0> set dhcp.role=client
TR0153 Rev. D2
60
EnRoute50x/51x User’s Guide
To disable Ethernet DHCP client mode, set the DHCP role parameter to „none‟ as shown
below.
> use eth0
eth0> set dhcp.role=none
Web GUI
The Ethernet DHCP role value can be set via the web interface using the “DHCP” sub-tab on
the “DHCP” tab on the “System Parameters” page (see Figure 30).
8.2.2
Manual IP Configuration
When a node is configured as a gateway, there are no limitations imposed by the EnRoute500
on the IP address assigned to the Ethernet interface. If the Ethernet DHCP role parameter is
set to „none‟, the manually configured IP address will be used. The default IP configuration that
is assigned to the interface based on the node and mesh ID settings is available through the
CLI and the web GUI.
Note that for the manually configured IP address to be used, the Ethernet DHCP role setting
must be set to „none‟ if the node is connected to a network which provides access to a DHCP
server.
The IP configuration settings shown in the „eth0‟ interface in the CLI and on the
“Wired/Backhaul Interface” page of the web interface do not necessarily reflect the
current settings of the interface. They are the requested settings and do not take into
account whether the interface has been configured via DHCP. If the Ethernet DHCP
role parameter is set to „client‟, the „ip.address‟, ip.broadcast‟, „ip.gateway‟, and
„ip.netmask‟ parameters will respond to a „get‟ command with „‟ to indicate
that the parameters will be assigned by a DHCP server instead of any values
assigned via the CLI. Use the „ifconfig eth0‟ command in the CLI or access the
“Status” page in the web interface to get current interface settings.
CLI
The Ethernet default IP configuration is available through the following read-only parameters:
ip.address – IP address
ip.broadcast – IP broadcast address
ip.gateway – default gateway
ip.netmask – netmask
TR0153 Rev. D2
61
EnRoute50x/51x User’s Guide
These parameters cannot be set though. These default parameters can be overridden with the
parameters listed below.
ip.address_force
ip.broadcast_force
ip.gateway_force
ip.netmask_force
The example below, shows how a custom IP address can be set for the Ethernet interface
> use
eth0>
eth0>
eth0>
eth0>
eth0>
eth0
set dhcp=none
set ip.address_force=192.168.1.2
set ip.broadcast_force=192.168.1.255
set ip.gateway_force=192.168.1.1
set ip.netmask_force=255.255.255.0
Web GUI
When the node is in gateway mode, the Ethernet IP address, gateway, netmask, and
broadcast address parameters can be set via the web interface using the “Wired/Backhaul
Interface” page (see Figure 31). The current IP values can be viewed on the “Status” page.
TR0153 Rev. D2
62
EnRoute50x/51x User’s Guide
Access Point (AP) Configuration
The EnRoute500 has an 802.11b/g radio dedicated to access point traffic. The settings for this
radio are independent of any settings for the radio used for the mesh backhaul traffic. The
settings for the access points can vary from node to node in the mesh, but typically it is
desirable to set certain parameters to the same value for all the access points in a mesh to
allow clients to roam seamlessly within the mesh network.
An EnRoute500 has four access points that can be configured to suit different application
needs. With the exception of the „wlanN.channel‟ parameter, all access point parameters can
be configured independently of each other.
The interfaces for the access points will be referred to as „wlanN‟ when it applies to
all four access points. „wlan1‟ will be used in all examples.
Figure 32. Access point interfaces
9.1
Access Point Interfaces
There are four access point interfaces that are used to configure the access points: wlan1,
wlan2, wlan3, and wlan4. The access points have equivalent configuration capabilities and
TR0153 Rev. D2
63
EnRoute50x/51x User’s Guide
there is no inherent prioritization or preference for one access point. The section on quality-ofservice settings (section 13) describes how prioritization on a per-access point basis can be
configured.
9.2
Enabling and Disabling Access Points
Access points can be individually enabled or disabled. An access point can be configured
when it is disabled and parameter settings are retained when it is disabled.
CLI
An access point can be enabled with the „enable‟ parameter in the „wlanN‟ interface as shown
below.
> use wlan1
wlan1> set enable=yes
An access point can be disabled with the following commands.
> use wlan1
wlan1> set enable=no
Web GUI
The access point status can be set via the web interface using the appropriate “wlanN” tab on
the “Wireless Interfaces” page (see Figure 32).
9.3
Access Point Client Device Address Space
The enabled wlanN interfaces are assigned segments of the class C address space that each
node has to share between its client interfaces, which include eth0, wlan1, wlan2, wlan3, and
wlan4. The start address of the address segment and its size can be set with the IP address
range start address and size parameters. The following restrictions are placed on the address
segment configuration:
Each active interface must be assigned an address segment.
The IP address range start address („ip.start.requested‟ in the CLI) must be one of the
following values: 1, 33, 65, 97, 129, 161, 193, 225.
The IP address range size („ip.size.requested‟ in the CLI) must be one of the following
values: 31, 63, 127, 255.
The IP address range size and start address must be chosen such that the address
segment does not cross a netmask boundary. Table 9 lists allowed combinations.
The address spaces for enabled interfaces must start at different addresses.
TR0153 Rev. D2
64
EnRoute50x/51x User’s Guide
The address spaces for enabled interfaces should not overlap.
Each of the enabled interfaces‟ address segments should be configured to avoid overlap with
the other interfaces‟ address segments. In the case where a node is configured such that this
requirement is not met, address spaces will be automatically reduced in size to prevent
overlap.
CLI
In the example below, the WLAN interfaces are set up to use the lower half of the class C
address space. This assumes that the Ethernet interface is either used for gateway purposes
or is assigned to an address segment in the upper half of the class C network.
> use wlan1
wlan1> set ip.start.requested=1
wlan1> set ip.size.requested=31
wlan1> use wlan2
wlan2> set ip.start.requested=33
wlan2> set ip.size.requested=31
wlan2> use wlan3
wlan3> set ip.start.requested=65
wlan3> set ip.size.requested=31
wlan3> use wlan4
wlan4> set ip.start.requested=97
wlan4> set ip.size.requested=31
The actual start address and size of a segment are accessible via the „ip.start.actual‟ and
„ip.size.actual‟ parameters. These may differ from the requested values if incompatible
requested values have been set for different interfaces.
Web GUI
The eth0 address segment start address and size can be set via the web interface using the
“DHCP” sub-tab on the “DHCP” tab on the “System Parameters” page (see Figure 33).
TR0153 Rev. D2
65
EnRoute50x/51x User’s Guide
Figure 33. ‘wlanN’ DHCP and address space settings
9.4
Channel
The 802.11b/g radio can be set to operate in the channels listed in Table 10.
TR0153 Rev. D2
66
EnRoute50x/51x User’s Guide
Channel
10
11
Center Frequency (GHz)
2.412
2.417
2.422
2.427
2.432
2.437
2.442
2.447
2.452
2.457
2.462
Table 10. Access point channels and associated center frequencies
Note that only channels 1, 6, and 11 are non-overlapping.
It is not possible to configure access points to use different channels. If the channel
for wlan2 is changed, the channel will be changed for wlan1, wlan3, and wlan4.
However, different nodes in a mesh cluster can be set to use different access point
channels in order to reduce co-channel interference.
CLI
The AP channel is set with the „channel‟ parameter in the „wlanN‟ interfaces. The example
below shows how to set the AP channel to 6.
> use wlan1
wlan1> set channel=6
Web GUI
The access point channel can be set via the web interface using the appropriate “wlanN” tab
on the “Wireless Interfaces” page (see Figure 32).
9.5
ESSID
The ESSID, or Extended Service Set Identifier, is used in 802.11 infrastructure networks to
identify a particular network. It is used to differentiate logical networks that operate on the
same channel.
TR0153 Rev. D2
67
EnRoute50x/51x User’s Guide
Each access point can be configured with a different ESSID. This allows network
traffic to be separated based on ESSID. Assigning unique ESSIDs to the access
points in a mesh has the benefit of allowing a user to configure a client device to
connect to a specific node in the mesh. Typically a mesh will be deployed with the
access point ESSIDs having the same set of values for each EnRoute500 in order to
support seamless roaming.
The ESSID value must be a text string that has a maximum length of 32 characters. It must
only contain alphanumeric characters, spaces, dashes (“-“), and underscores (“_”).The ESSID
setting is case sensitive.
It is possible to hide an AP ESSID by restricting it from being broadcast. Whether it is
appropriate for an AP ESSID to be hidden depends on the application.
CLI
The access point ESSID is set as shown in the example below. When setting an ESSID that
contains spaces, the ESSID value must be enclosed by quotes – the quotes are optional
otherwise.
> use wlan1
wlan1> set essid=”wlan1_ap”
The broadcast of the ESSID can be controlled with the „hide_essid‟ parameter in the „wlanN‟
interface. The example below shows how hiding of the ESSID can be enabled.
> use wlan1
wlan1> set hide_essid=yes
Web GUI
The access point ESSIDs and its broadcast state can be set via the web interface using the
appropriate “wlanN” tab on the “Wireless Interfaces” page (see Figure 32).
9.6
IP Configuration for Nodes and Their Clients
The access point interfaces allow client devices to connect to access the mesh network. The
client devices can either be assigned their IP configuration using DHCP or be manually
configured.
TR0153 Rev. D2
68
EnRoute50x/51x User’s Guide
9.6.1
Access Point IP Address
The IP address, broadcast address, and netmask associated with an access point interface
can be viewed, but not directly changed through the CLI or web GUI. To set the IP address to
the desired value, modify the node ID, mesh ID, and LAN prefix parameters (see sections 6.3
and 6.5). You can view the resulting settings for the AP interface with either the CLI or the web
GUI.
CLI
You can view the IP configuration settings for the AP interface with the „ip.*‟ parameters in the
„wlanN‟ interface as shown in the example below.
> use wlan1
wlan1> get ip.address
ip.address = 10.2.4.1
wlan1> get ip.broadcast
ip.broadcast = 10.2.4.127
wlan1> get ip.gateway
ip.gateway =
wlan1> get ip.netmask
ip.netmask = 255.255.255.128
Web GUI
The access points‟ IP settings are available through the web interface on the “Status” page.
9.6.2
IP Configuration of Clients Devices via DHCP
The EnRoute500 can be set to serve IP addresses to clients on the access point interfaces
using DHCP. Two distinct modes for providing IP addresses via DHCP exist. These are
described in depth in section 10.
9.6.3
Manual IP Configuration of Client Devices
Client devices that use static IP addresses must have an IP address that is within the subnet
of the access point interface that they connect to.
If the local DHCP server is enabled for an access point interface, IP addresses must be
reserved for statically configured devices by setting the DHCP reserve parameter. This will
reserve the specified number of IP addresses at the bottom of the IP range for the interface.
For example, if the interface has the IP address 10.2.4.1, the netmask 255.255.255.128, and
the DHCP reserve value 5, the IP addresses 10.2.4.2 through 10.2.4.6 will be available for
TR0153 Rev. D2
69
EnRoute50x/51x User’s Guide
use by statically configured devices. The remaining IP addresses in the interfaces address
space can be assigned by the DHCP server to other client devices.
CLI
The number of IP addresses reserved for statically-configured devices connected to the
Ethernet interface is set with the „dhcp.reserve‟ parameter in the „eth0‟ interface.
Web GUI
The „dhcp.reserve‟ value can be set via the web interface using the “DHCP” sub-tab on the
“DHCP” tab on the “System Parameters” page (see Figure 33).
9.7
Client Devices
Each access point has a status page that displays information about attached clients and total
throughput through the access point. The signal strength of each client device, it‟s MAC
address, its IP address, and the time since data was last received from it are listed. The status
pages can be accessed under the „Status‟ tab on the „Status‟ page, as shown in Figure 34.
Figure 34. Access point client status information
9.8
Encryption and Authentication
The EnRoute500 supports several common encryption/authentication schemes, including
WEP, WPA, and WPA2, to provide secure wireless access for client devices. WEP keys with
40-bit or 104-bit lengths, pre-shared WPA keys, and multiple WPA-EAP modes.
TR0153 Rev. D2
70
EnRoute50x/51x User’s Guide
The WEP and WPA configuration settings for each access point are independent. An access
point can only support one of the encryption/authentication modes at a time, but the APs in the
EnRoute500 do not all have to use the same encryption/authentication scheme.
Figure 35. Access point authentication and encryption settings
9.8.1
WEP Encryption
The access points can be protected with a WEP-based encryption key to prevent unauthorized
users from intercepting or spoofing traffic.
CLI
To enable WEP-based encryption, set the „key‟ parameter in the „wlanN‟ interface. The length
of the encryption key is determined by the format used to specify the „key‟ value. Valid key
formats and the corresponding encryption type and key length are listed in Table 11.
If WPA is enabled for an interface („wpa.enable‟ CLI parameter in the „wlanN‟
interfaces), the WPA settings will be used for encryption and authentication and the
„key‟ value used to enable WEP will be ignored.
TR0153 Rev. D2
71
EnRoute50x/51x User’s Guide
Key format
s:<5 ASCII characters>
<10 hex values>
s:<13 ASCII characters>
<26 hex values>

Encryption format
Encryption key length
WEP
40 bits
WEP
104 bits
None
N/A
Table 11. WEP encryption key formats
For example, 104-bit WEP encryption can be enabled using an ASCII key with
> use wlan1
wlan1> set key=”s:abcdefghijklm”
or using a hexadecimal key with
> use wlan1
wlan1> set key=”0123456789abcdef0123456789”
WEP encryption can be disabled by specifying a blank value as shown below.
> use wlan1
wlan1> set key=
Web GUI
WEP encryption can be enabled and the key can be set via the web interface using the
“WPA/WEP” sub-tab under the “AAA” tab on the “System Parameters” page (see Figure 35).
Select “WEP” as the type of encryption from the drop-down menu for the access point you
wish to configure and set the WEP key in the text box below the drop-down menu. In the
example in Figure 35, „wlan1‟ has been configured to use WEP.
9.8.2
WPA Pre-Shared Key Mode (WPA-PSK)
In WPA pre-shared key (PSK) mode, a common passphrase is used for clients connecting to
an EnRoute500 AP. To set the WPA-PSK mode, enable WPA for the interface and set the preshared key value as shown below. The passphrase must be between 8 and 63 characters in
length.
The minimum number of characters required for the WPA passphrase is 8. However,
it is recommended that a longer passphrase, on the order of 15-20 characters, is
used to increase the strength of the encryption used for the wireless link.
TR0153 Rev. D2
72
EnRoute50x/51x User’s Guide
CLI
The example below shows how to enable WPA-PSK mode for wlan1. The „wpa.key_mgmt‟
parameter must also be set to indicate that PSK mode is being used, as shown below.
> use wlan1
wlan1> set wpa.enable=yes
wlan1> set wpa.key_mgmt=”WPA-PSK”
wlan1> set wpa.passphrase=long_passphrases_improve_encryption_effectiveness
Web GUI
WPA-PSK can be enabled and the pre-shared key can be set via the web interface using the
“WPA/WEP” sub-tab under the “AAA” tab on the “System Parameters” page (see Figure 35).
Select “WPA-PSK” as the type of encryption/authentication from the drop-down menu for the
access point you wish to configure and enter the WPA-PSK key in the text box below the dropdown menu. In the example in Figure 35, „wlan2‟ has been configured to use WPA-PSK.
9.8.3
WPA EAP Mode
In WPA-EAP mode, a client device is authenticated using an 802.1x authentication server,
which is typically a RADIUS server.
The supported EAP modes are:
TLS
PEAP-TLS
TTLS
PEAP-MSCHAPv2
(X509v3 server & client certificates)
(X509v3 server & client certificates)
(X509v3 server certificate)
(X509v3 server certificate)
The following information must be provided about the RADIUS server:
address – the IP address of the 802.1x server that will be used for authentication
port – the port that the authentication server is listening on (UDP port 1812 by default)
secret – the shared secret for the authentication server. The secret must be a string that is
no longer than 32 characters in length.
CLI
To configure the EnRoute500 to support 802.1x authentication, the following parameters in a
„wlanN‟ interface must be set:
wpa.enable
wpa.key_mgmt
wpa.auth.server.addr
TR0153 Rev. D2
73
EnRoute50x/51x User’s Guide
wpa.auth.server.port
wpa.auth.server.shared_secret
The „wpa.key_mgmt‟ parameter must be set to indicate that both PSK and EAP modes can be
supported, as shown in the example below.
The example below shows how to enable WPA EAP mode.
> use wlan1
wlan1> set wpa.enable=yes
wlan1> set wpa.key_mgmt=”WPA-PSK WPA-EAP”
wlan1> set wpa.auth.server.addr=1.2.3.4
wlan1> set wpa.auth.server.port=1812
wlan1> set wpa.auth.shared_secret=enroute500_radius_secret
Web GUI
WPA-EAP can be enabled and the authentication server parameters can be set via the web
interface using the “WPA/WEP” sub-tab under the “AAA” tab on the “System Parameters” page
(see Figure 35). Select “WPA-EAP” as the type of encryption/authentication from the dropdown menu for the access point you wish to configure and set the authentication server IP
address, port, and secret in the text boxes below the drop-down menu. In the example in
Figure 35, „wlan3‟ has been configured to use WPA-EAP.
9.9
Transmit Power
The transmit power of the access point radio is configurable. Increased output power will
improve communication range, but will also extend the interference range of the radios. The
default power level is 22 dBm.
The output power for any ‘wlanN’ interfaces must be no greater than the
values listed in Table 12 to be in compliance with FCC regulations. Note that
the power limit is dependent on the channel selected.
Channel
1-11
Output power (dBm)
22 dBm
CLI setting
25
Table 12. Access point transmit power limits
TR0153 Rev. D2
74
EnRoute50x/51x User’s Guide
When setting the output power for an access point, consider the output power of the
clients that will be communicating the access point. If these devices have output
power levels that are far lower than that of the access point, an asymmetric link may
result. Such a link exists when the received signal strength at clients is sufficient for
a downlink to the client be established, but the received signal level at the access
point is not sufficient for an uplink from the client to be established.
CLI
The example below shows how to set the access point radio‟s transmit power using the CLI.
Note that the value is not specified in dBm. Refer to Table 13 for correlation between output
power and the value set through the CLI.
> use wlan1
wlan1> set txpower=13
CLI txpower Value
10
13
Output Power (dBm)
18
20
22
Table 13. AP radio output power settings in the CLI
Web GUI
The access points transmit power can be set via the web interface using the appropriate
“wlanN” tab on the “Wireless Interfaces” page (see Figure 32). Drop-down menus display a list
of output power choices in dBm.
TR0153 Rev. D2
75
EnRoute50x/51x User’s Guide
10 Client DHCP Configuration
Two configuration options exists for assigning IP addresses to client devices using DHCP:
Each EnRoute500 hosts a local DHCP server and supplies IP addresses to devices
attaching to any of the client interfaces
A centralized DHCP server supplies IP addresses to client devices, with the EnRoute500s
relaying DHCP messages between client devices and the centralized server.
All client interfaces in a mesh cluster must use the same DHCP mode or have DHCP disabled.
10.1
Using Local DHCP Servers
The EnRoute500 can be set to serve IP addresses to clients on enabled access point
interfaces and the Ethernet interface on repeater nodes using DHCP. The DHCP role
parameters in the „wlanN‟ and „eth0‟ interfaces control DHCP behavior. When the role is set to
„server‟, the EnRoute500 will respond to DHCP requests received from client devices
connected to the interface.
The IP addresses provided by the DHCP server will be in the subnet defined by the LAN prefix
(„sys.id.lanprefix‟), mesh ID („sys.id.mesh‟), node ID („sys.id.node‟) and the IP address range
start address and size parameters in the appropriate client interface („.ip.start.actual‟ and
„.ip.size.actual‟). For example, for the „wlan1‟ interface, the start and end of the address
range are:
Start address =
End address =
.
.
.
 + 1
.
.
.
< wlan1 IP address range start address > < wlan1 IP address range size > - 2
The EnRoute500 can be configured to set aside a number of IP addresses for client devices
that will use a static IP address. These IP addresses are taken from the pool that DHCP
assigns IP addresses from. Thus, increasing the number of IP addresses set aside for
devices with static IP addresses will reduce the size of the DHCP address pool. The DHCP
reserve parameter controls the number of IP addresses that will be reserved for static use. By
default, this parameter is set to zero, assigning the maximum possible number of IP
TR0153 Rev. D2
76
EnRoute50x/51x User’s Guide
addresses to the DHCP pool. You may reserve the entire range of IP addresses, but the
EnRoute500 will use at least the highest address in the range for DHCP.
If the „dhcp.reserve‟ value is non-zero, the DHCP range start address will be affected as shown
below
Start address =
.
.
.
 + 1 - < wlan1 DHCP reserve>
CLI
The examples below show how to set the DHCP server state for the „wlan1‟ interface.
> use wlan1
wlan1> set dhcp.role=server
To disable the DHCP server, set the „dhcp.role‟ parameter to „none‟
> use wlan1
wlan1> set dhcp.role=none
The example below shows how to set the DHCP reserve parameter
> use wlan1
wlan1> set dhcp.reserve=5
Web GUI
The access point and wired interface DHCP servers‟ state can be set via the web interface
using the “DHCP” sub-tab under the “DHCP” tab on the “System Parameters” page (see
Figure 36). All of the access points‟ DHCP settings can be configured on this page.
The DHCP reserve setting for all access points and the wired interface can be set via the web
interface using the “DHCP” sub-tab under the “DHCP” tab on the “System Parameters” page
(see Figure 36).
TR0153 Rev. D2
77
EnRoute50x/51x User’s Guide
Figure 36. Access point DHCP configuration
TR0153 Rev. D2
78
EnRoute50x/51x User’s Guide
10.2
Using a Centralized DHCP Server
DHCP relay enables assignment of IP addresses to wireless clients from a common remote
DHCP server. The remote DHCP server may reside either on a host connected to the mesh
gateway‟s wired segment, or on a server that is beyond one or more routers. When using a
common DHCP server, wireless clients are assigned IP addresses from a single address pool,
and are allowed to keep their IP address while roaming seamlessly from AP to AP. Even
though they will not move seamlessly from one node to another, wired clients can also have
their IP addresses assigned by a centralized server.
There are three classes of entities that must be configured when using this DHCP mode:
1. The individual EnRoute500s, including the repeaters and the gateway node
2. The central DHCP server
3. Any intermediate router(s) in the path between the DHCP server and the mesh cluster
gateway node
When using a centralized DHCP server, an address space, from which client IP addresses are
assigned, must be defined. The client interfaces on the EnRoute500s (there can be up to 5 per
node) must also have IP addresses that belong to this address space in order to facilitate
DHCP relay and selection of client IP addresses from the correct DHCP scope on servers that
serve hosts connected to different subnets. The client interface IP addresses need to be
configured statically. It is recommended that a contiguous range of IP addresses at either the
beginning or the end of the address space be set aside, one for each client interface on the
mesh nodes.
Consider the example where a mesh cluster consists of 3 nodes, including the gateway node.
The DHCP server resides on a host that also acts as the upstream router and is connected to
the mesh gateway‟s wired segment. We will set aside 15 IP addresses for the mesh nodes‟
client interfaces (3 nodes, up to 5 interfaces per node). Assuming the client address space is
192.168.5.0/24, with available addresses from 192.168.5.1 to 192.168.5.255, we will use
192.168.5.1 for the server hosting the DHCP server, 192.168.5.2 for the mesh gateway‟s
backhaul interface, set aside 192.168.5.3 to 192.168.5.18 for the mesh AP interfaces, and
configure the remote DHCP server to serve IP addresses in the range of 192.168.5.19 to
192.168.5.254 to wireless clients. We will keep 192.168.5.255 as the broadcast address for the
mesh cluster.
10.2.1
Configuring the EnRoute500s
When operating in centralized DHCP mode, Each EnRoute500 in a mesh cluster must be
configured to use centralized DHCP mode and to use the same centralized DHCP server. The
IP address of the central DHCP server is set with the DHCP relay server parameter. The
server must be reachable through the mesh cluster gateway‟s wired backhaul interface.
TR0153 Rev. D2
79
EnRoute50x/51x User’s Guide
Each client interface on the EnRoute500 that is to support centralized DHCP mode must be
configured to be in DHCP server mode for it to support relay of IP addresses to clients from a
central DHCP server. This configuration is set with the DHCP role parameter in each of the
client interfaces (eth0, wlan1-4).
It is possible to disable DHCP address assignments to clients on a per-interface basis and
have them use static IP addresses instead. To disable DHCP for an interface, set the DHCP
role parameter associated with the interface to „none‟.
The address space that is to be used for the wireless clients is a subnet specified with the
Client Address Space parameter. This subnet can either be a class A (/8), class B (/16), or
class C (/24) network. The value must be specified in CIDR notation (a subnet and its size
separated by a „/‟), e.g. „192.168.5.0/24‟
The IP addresses of the client interfaces (eth0, wlan1-4) need to be manually assigned to each
of the nodes in the mesh cluster. This is done by setting the Address Base parameter for the
interfaces, which is assigned to the first enabled client interface. Addresses for the remaining
client interfaces are determined by successively incrementing the Base Address by 1. It is
recommended that the gateway in a mesh cluster be assigned the lowest available value (3 in
the example in the CLI section below) and the repeaters in the mesh cluster are given
successively higher values, with an increment of 5 between them (5 is the maximum number of
client interfaces available on each mesh node, including the Ethernet interface on mesh
repeaters).
CLI
DHCP relay mode is enabled using the „dhcp.relay.enable‟ and „l2.client_mac_fwd‟ parameters
in the „sys‟ interface as shown in the example below.
> use sys
sys> set dhcp.relay.enable=yes
sys> set l2.client_mac_fwd=yes
In the example below, the central DHCP server resides on a host on the same segment to
which the mesh gateway‟s wired interface is connected.
> use sys
sys> set dhcp.relay.server=192.168.5.1
The example below shows how to set the DHCP role parameter for the wlan1 and wlan2
interfaces.
> use wlan1
wlan1> set dhcp=server
> use wlan2
wlan2> set dhcp=server
To disable distribution of centralized DHCP addresses on an interface, set the interface‟s
„dhcp.role‟ parameter to „none‟ as shown below.
TR0153 Rev. D2
80
EnRoute50x/51x User’s Guide
> use wlan3
wlan3> set dhcp=none
The Client Address Space value is set with the „dhcp.relay.dhcp_subnet‟ parameter in the „sys‟
interface. This value should be a class A, B, or, C subnet specified using CIDR notation as
shown in the example below.
> use sys
sys> set dhcp.relay.dhcp_subnet=192.168.5.0/24
The Base Value, which sets the IP address of client interfaces on a node, is set through the
„dhcp.relay.base‟ parameter in the „sys‟ interface. The example below shows the configuration
for a mesh cluster consisting of 3 nodes.
On the gateway:
> use sys
sys> set dhcp.relay.base=192.168.5.3
on the first repeater node:
> use sys
sys> set dhcp.relay.base=192.168.5.8
and on the second repeater node:
> use sys
sys> set dhcp.relay.base=192.168.5.13
Note that the value of the fourth octet increases by 5 for each node since that is the number of
client interfaces that each node has, and each interface requires one IP address.
Web GUI
DHCP relay mode can be enabled via the web interface on the “DHCP Relay” sub-tab under
the “DHCP” tab on the “System Parameters” page (see Figure 37). The external DHCP server
IP address, the Client Address Space parameter, and the Base Value can also be set on this
page. The DHCP role parameters for all interfaces can be set on the “DHCP” sub-tab under
the “DHCP” tab on the “System Parameters” page.
TR0153 Rev. D2
81
EnRoute50x/51x User’s Guide
Figure 37. DHCP relay settings for use with a centralized DHCP server
10.2.2
Configuring the Central DHCP Server
Guidelines for configuring the central DHCP server are provided below. The full configuration
of the central DHCP server will depend on the type of DHCP server that is used and is beyond
the scope of this document.
Typically the following information must be available in order to configure the server:
1. The local interface (to the DHCP server) over which the DHCP-related messages from
the mesh cluster arrive
2. The parameter(s) that define the address lease time
3. Whether DNS and domain names are to be provided by the DHCP server to clients
4. The range of the flat IP address that is used for assigning IP addresses to clients. The
range must not include the IP addresses set aside for the client interfaces on each
mesh node.
The following is a segment of the dhcpd.conf file for a Linux DHCP server (ISC DHCP server)
that illustrates the scope settings for the mesh network:
subnet 192.168.5.0 netmask 255.255.255.0
option broadcast-address
192.168.5.255;
option subnet-mask
255.255.255.0;
option domain-name
"domain.com";
range
192.168.5.18 192.168.5.254;
Note that in this definition no “routers” option is needed. If a global “routers” option is defined, it
will be set to the correct value for proper operation inside the mesh network. In this example,
TR0153 Rev. D2
82
EnRoute50x/51x User’s Guide
the mesh network includes 3 mesh nodes, 2 IP addresses are set aside for the DHCP server
and the mesh gateway, and therefore the address pool starts from 192.168.5.18.
TR0153 Rev. D2
83
EnRoute50x/51x User’s Guide
11 Connecting an EnRoute500 Gateway to a WAN
The options for connecting an EnRoute500 gateway to a WAN are described below.
11.1
Manual Configuration
An EnRoute500 gateway can be directly connected to a WAN without using Network Address
Translation. With this gateway configuration, the router on the network that the gateway is
attached to must be configured to forward the mesh subnet and the LAN subnets to the
gateway‟s Ethernet IP address. The subnets that need to be forwarded are:
Class B subnet:
Class C subnet:
..0.0
..0
In the case where the LAN prefix is 10, the mesh ID is 2, and the mesh prefix is 172.29, the
subnets the router would need to forward to the gateway are 10.2.0.0/255.255.0.0 and
172.29.2.0/255.255.255.0.
CLI
The subnet information can be retrieved from the „sys‟ interface as shown below.
> use sys
sys> get id.*
sys.id.lanprefix = 10
sys.id.mesh = 2
sys.id.meshprefix = 172.29
sys.id.node = 4
Web GUI
The LAN prefix and mesh prefix can be obtained by inspecting the IP addresses available on
the “Status” page. Alternatively, the mesh ID can be obtained from the “Mesh” tab on the
“Wireless Interfaces” page and the LAN prefix can be obtained form the “System” tab on the
“System” page.
11.2
Network Address Translation (NAT)
Network Address Translation (NAT) isolates a mesh cluster from the WAN network that its
gateway is connected to. The mesh nodes and their client devices are able to communicate
with devices connected to the external network that the mesh gateway is connected to.
TR0153 Rev. D2
84
EnRoute50x/51x User’s Guide
However, devices on the external network cannot initiate communication with any nodes in the
mesh cluster, or their clients, other than the mesh cluster gateway.
The advantages of using NAT are:
You can easily attach a mesh cluster to an existing network. You do not need to modify any
settings on the router on your existing network to forward packets to the IP addresses
used in your mesh cluster.
The nodes in the mesh cluster are shielded from the network that the gateway is attached
to.
You only consume a single IP address on your existing network when connecting the mesh
cluster to it.
The main disadvantage of using NAT is
You are not able to initiate connections with nodes in the mesh cluster or their clients from
outside the mesh cluster.
CLI
To set the NAT state, use the commands
> use sys
sys> set nat.enable=
Web GUI
The NAT state can be set via the web interface on the “Wired/Backhaul Interface” page (Figure
38).
TR0153 Rev. D2
85
EnRoute50x/51x User’s Guide
Figure 38. NAT setting
11.3
VPN Access to a Mesh Gateway
An EnRoute500 configured as a gateway can establish a VPN connection to an OpenVPN
server. This VPN connection provides the following capabilities:
Any node in the mesh can be contacted directly from a remote host, even when NAT is
enabled on the gateway node. This allows remote access to nodes to monitor their
behavior or reconfigure them
A secure path between the mesh and a host, which can be used to monitor and reconfigure
the mesh, is established. The control and status traffic passing between the mesh and the
host is protected if it passes over a public network at any point.
The state of the VPN client on the EnRoute500 is set with the Enable VPN parameter. The IP
address of the VPN server and its port are specified with the VPN Server and VPN Port
parameters. Note that the VPN server parameter can either be an IP address or a resolvable
host name.
CLI
The example below shows how to enable the VPN connection („vpn.enable‟ in the „sys‟
interface) and set the server and port parameters („vpn.server‟ and „vpn.port‟ in the „sys‟
interface).
TR0153 Rev. D2
86
EnRoute50x/51x User’s Guide
> use eth0
sys> set vpn.enable=yes
sys> set vpn.server=192.168.0.1
sys> set vpn.port=1194
Web GUI
These parameters can be set via the web interface on the “Wired/Backhaul Interface” page
when the node scheme is set to „gateway‟.
Figure 39. VPN client settings
TR0153 Rev. D2
87
EnRoute50x/51x User’s Guide
12 Controlling Access to the EnRoute500
The EnRoute500 supports the following features for restricting access to the mesh node, interclient device communication and access to mesh nodes and client devices from an external
network:
Firewall
Client-to-client communication blocking
Gateway firewall
It further supports controlled network access by client devices through MAC address black lists
and mesh association through MAC white lists.
12.1
Firewall
The EnRoute500 has a firewall that blocks traffic destined for the EnRoute500. This prevents
client devices attached to a node and devices on the mesh gateway WAN from connecting to
the node.
The firewall only affects packets destined for the EnRoute500. All traffic destined for
devices „past‟ the EnRoute500 is not affected by the firewall. This means the firewall
needs to be enabled on every EnRoute500 or connected clients will have full access
to the EnRoute500‟s private ports.
By default, the ports listed in Table 14 are set to be allowed.
Function
SSH
HTTPS
HTTP redirect
DNS
DHCP
DHCP
Roaming support
Roaming support
Port
22
443
3060
53
67
68
7202
7203
Type
Source & destination
Destination
Destination
Source & destination
Destination
Destination
Destination
Destination
Protocol
TCP
TCP
TCP
UDP
UDP
UDP
UDP
UDP
Table 14. Source and destination ports allowed by default
TR0153 Rev. D2
88
EnRoute50x/51x User’s Guide
If ports that are open by default are reconfigured to be closed, certain EnRoute500
functions will be affected. It is strongly recommended that all of the ports listed in
Table 14 be kept open.
CLI
The firewall is enabled by selecting the „firewall‟ interface and setting the „node.enable‟
parameter.
> use firewall
firewall> set node.enable=yes
Lists of allowed source and destination ports for inbound TCP and UDP traffic can be
specified. These lists can be set with the following parameters in the „firewall‟ interface:
node.tcp.allow.dest
node.tcp.allow.source
node.udp.allow.dest
node.udp.allow.source
The list of allowed ports must be a space-delimited string enclosed by quotes. The example
below shows how to set the TCP source ports parameters.
> use firewall
firewall> set node.tcp.allow.dest=”22 23 80 5280”
12.2
Gateway Firewall
The gateway firewall blocks connections originating outside the mesh cluster from entering the
mesh via the gateway, protecting mesh nodes and their clients from unwanted traffic. The
gateway firewall will permit return traffic for connections that originate inside the mesh cluster
or on mesh clients.
The gateway firewall should only be enabled on EnRoute500‟s that are configured as
gateways. It is possible to have the gateway firewall set to be enabled on a repeater node, but
it does not have any effect on the flow of traffic through the node‟s Ethernet interface.
If you have enabled NAT (see section 11.2) on the Ethernet interface „eth0‟, you will
have an implicit firewall that limits the type of inbound connections that are possible.
CLI
The state of the gateway firewall is controlled with the „gateway‟ parameter in the „firewall‟
interface. Enable the gateway firewall with
TR0153 Rev. D2
89
EnRoute50x/51x User’s Guide
> use firewall
firewall> set gateway=yes
disable it with
> use firewall
firewall> set gateway=no
12.3
Blocking Client-to-Client Traffic
Client-to-client traffic can be blocked or permitted on a per-interface basis. By enabling clientto-client traffic blocking for one or more of an EnRoute500‟s client interfaces, the clients that
attach to that particular interface will not be able to communicate with any clients attached to
that or any other client interface in the mesh. Client-to-client traffic can be controlled for
interfaces wlan1, wlan2, wlan3, wlan4, and eth0.
CLI
The parameters that control client-to-client access are all in the „firewall‟ interface. They are:
node.allowc2c.eth0
node.allowc2c.wlan1
node.allowc2c.wlan2
node.allowc2c.wlan3
node.allowc2c.wlan4
To block client-to-client traffic, select the „firewall‟ interface and set the parameter for the
appropriate interface to „no‟, To allow traffic between clients, set the parameter to „yes‟. The
examples below illustrate the how to configure these parameters.
To block client-to-client traffic for clients attached to wlan1:
> use firewall
firewall> set node.allowc2c.wlan1=no
To allow client-to-client traffic for clients attached to eth0:
> use firewall
firewall> set node.allowc2c.eth0=yes
Web GUI
The client isolation parameters can be set via the web interface using the “Firewall” tab on the
“Security” page (see Figure 40). By setting an interface‟s client isolation parameter to „yes‟,
TR0153 Rev. D2
90
EnRoute50x/51x User’s Guide
clients connecting to that interface will not be able to communicate with any other clients in the
mesh.
Figure 40. Client-to-client firewall settings
Note that devices connected to different interfaces can only communicate with each other if
client-to-client isolation is disabled for both interfaces.
Client-to-client isolation is only enabled if the EnRoute500 node firewall
(firewall.node.enable) is enabled (section 12.1).
TR0153 Rev. D2
91
EnRoute50x/51x User’s Guide
12.4
Access Control Lists (ACLs)
Access control lists can be created for each of the access point interfaces and the mesh
interface.
12.4.1
Access Point Access Control Lists (ACLs)
The access control lists (ACLs) for the access point interfaces (wlan1-wlan4) block access to
any device with a MAC address matching those on the list. Individual ACLs can be defined for
each access point.
Web GUI
The ACLs can be defined via the web interface on the appropriate “wlanN” sub-tab under the
“ACL” tab on the “Security” page. Enter a MAC address and click on the “Add MAC” button to
add the address to the ACL for that access point. Once an address has been added, it will
appear at the bottom of the page. To delete a MAC address in an ACL, click on the “Delete
MAC” button next to the address.
The ACL for an access point must be enabled after it has been created. Choose “blacklist”
from the drop-down menu and click on “Change ACL Mode” to enable the list. Choose “none”
from the drop-down menu and click on “Change ACL Mode” to disable the ACL.
Figure 41. AP ACL configuration
TR0153 Rev. D2
92
EnRoute50x/51x User’s Guide
12.4.2
Mesh ACL
The access control list (ACL) for the mesh interface blocks access to the node via the mesh
interface for any node whose mesh MAC address is not listed in the ACL.
It is possible to isolate a mesh node from other nodes in the mesh if the mesh ACL
is incorrectly configured. If the mesh ACL is enabled and no MAC addresses are
present on the list, or the wrong addresses are present, it will not be possible for
other mesh nodes to communicate with the node.
Web GUI
The mesh ACL can be defined via the web interface on the “Mesh” sub-tab under the “ACL”
tab on the “Security” page. Enter a MAC address and click on the “Add MAC” button to add the
address to the ACL for that access point. Once an address has been added, it will appear at
the bottom of the page. To delete a MAC address in an ACL, click on the “Delete MAC” button
next to the address.
The ACL for an access point must be enabled after it has been created. Choose “whitelist”
from the drop-down menu and click on “Change ACL Mode” to enable the list. Choose “none”
from the drop-down menu and click on “Change ACL Mode” to disable the use of the ACL for
the mesh interface.
Figure 42. Mesh ACL configuration
TR0153 Rev. D2
93
EnRoute50x/51x User’s Guide
13 Quality of Service (QoS) Configuration
The EnRoute500 has extensive support for quality of service settings that allow traffic to be
prioritized based on the source interface, destination interface, and type of traffic. The
EnRoute500 QoS scheme allows both rate limiting and rate reservation for all interfaces.
13.1
Priority Levels
The Flow Priority parameters set the relative priority of outbound traffic based on the source
interface. These parameters can be set to an integer value in the range from 0 to 99, with a
higher number indicating a higher priority. If a priority level parameter is set to „inherit‟, the
interface will assume the default priority level.
Traffic originating from an interface with a higher priority will take priority over traffic from all
interfaces with a lower priority value until the higher-priority interface has no more data to
send. If multiple interfaces have the same priority level, their traffic will be given equal access
to the outbound interface. Rate reservation and rate limiting, described in the following
sections, can be used to avoid one interface dominating the use of the mesh interface
bandwidth.
As a rule, locally generated traffic should always have the highest priority so that
EnRoute500 control traffic has precedence over client traffic and the mesh can be
maintained.
The absolute value of the priority settings do not have any weighting effect. If a
priority is higher for one interface than another, the former will always be prioritized
with any remaining bandwidth allocated to the other one.
The Max/Min Hardware Priority parameters can be used to limit the hardware priority queues
that traffic from a particular interface can use for outbound traffic. Valid values for these
parameters are from 1 to 4, which are the priority levels listed in Table 15.
Abbreviation
VO
VI
BE
BK
Description
Voice
Video
Best Effort
Background
Priority level
4 (highest)
1 (lowest)
Table 15. Priority levels
TR0153 Rev. D2
94
EnRoute50x/51x User’s Guide
When sending data out through any of the wireless interfaces (wlanN, mesh0), these priorities
map directly to the hardware priority output queues on the wireless card. The default level is
Best Effort.
To increase the hardware priority of traffic from a particular interface, set the value of Min
Hardware Priority to a value larger than 1. This will force all traffic from the chosen interface to
use a hardware queue equal to or greater than the Min Hardware Priority value set. To reduce
the maximum hardware priority of traffic from an interface, set the Max Hardware Priority
parameter to a value less than 4. To disable hardware prioritization, set the Min/Max Hardware
Priority parameters to „0‟.
Changing hardware priorities does not affect the rate limiting and reservation (section 13.2), it
only affects which output hardware queues are used.
CLI
Flow priority levels are set with the „in..flow_priority‟ parameters in the „qos‟ interface,
where  is one of the following: default, local, eth0, mesh0, wlan1, wlan2, wlan3, wlan4.
„local‟ refers to traffic originating on the node itself, not from its clients (in practice this means
mesh network control traffic). The example below sets locally generated traffic to have top
priority and wlan1 to have priority over all other interfaces.
> use qos
qos> set in.default.flow_priority=10
qos> set in.local.flow_priority=90
qos> set in.wlan1.flow_priority=20
qos> set in.wlan2.flow_priority=inherit
qos> set in.wlan3.flow_priority=inherit
qos> set in.wlan4.flow_priority=inherit
qos> set in.eth0.flow_priority=inherit
Hardware priority levels are set with „in..hwpri{max,min}‟ in the „qos‟ interface, where
 is one of the following: default, local, eth0, mesh0, wlan1, wlan2, wlan3, wlan4.
The example below shows how to configure the system such that all traffic from „wlan1‟ with a
„Voice‟ or „Video‟ priority will be reduced to a „Best Effort‟ priority. Traffic with „Best Effort‟ and
„Background‟ priorities will not be affected.
> use qos
qos> set in.wlan1.hwpri.max=2
The example below shows how to configure the system such that all traffic from „wlan2‟ with a
„Background‟ or „Best Effort‟ priority will be increased to a „Video‟ priority. Traffic with „Video‟
and „Voice‟ priorities will not be affected.
> use qos
qos> set in.wlan2.hwpri.min=2
TR0153 Rev. D2
95
EnRoute50x/51x User’s Guide
Web GUI
Flow priorities can be set via the web interface under the “QoS” tab on the “QoS” page (see
Figure 43). The hardware priority levels can be set for each interface under the “Advanced
QoS” tab on the “QoS” page (see Figure 44).
Figure 43. QoS settings
TR0153 Rev. D2
96
EnRoute50x/51x User’s Guide
Figure 44. Advanced QoS configuration (only settings for some interfaces are shown)
13.2
Rate Limiting
A rate limit can be set at each QoS Control Point shown in Figure 45. The Control Points can
be split into three groups, listed below in decreasing order of importance:
Interface output limit
Interface output limit of traffic from a particular interface
Interface output limit of traffic of a certain type from a particular interface
All rate limit parameter values are in kbps. If no rate limit parameter is set, rate
limiting will be disabled for that interface or interface and traffic combination.
The maximum output data rate for interfaces can be limited with the Output Limit parameters
for each client interface. The default output limit value is applied to interfaces that have the
Output Limit parameter set to „inherit‟.
TR0153 Rev. D2
97
EnRoute50x/51x User’s Guide
Output
mesh0
eth0
wlan1
wlan2
wlan3
wlan4
wlan2
wlan3
wlan4
QoS Control Point
QOS
local
mesh0
eth0
wlan1
VI
VO
BK
BE
VI
VO
BK
BE
VI
VO
BK
BE
VI
VO
BK
BE
VI
VO
BK
BE
VI
VO
BK
BE
VI
VO
BK
BE
Input
Figure 45. Quality of Service rate limit control points
Data rate limits can also be imposed based on traffic type through an interface. The maximum
data rate for a certain type of traffic that enters the EnRoute500 through a particular interface
and exits it through another interface can be limited.
There is no standalone input rate limiting. Limiting the input rate of an interface only
makes sense in the context of the output for another interface(s). In most cases you
are concerned with mesh0 as the output interface.
CLI
The example below shows how to limit the maximum output rate of the mesh0 interface to 8
Mbps and the maximum output rates of all four wlanN interfaces to 2 Mbps each.
> use qos
qos> set out.mesh0.limit=8192
qos> set out.wlan1.limit=2048
qos> set out.wlan2.limit=2048
qos> set out.wlan3.limit=2048
qos> set out.wlan4.limit=2048
The maximum data rate for traffic that enters the EnRoute500 through a particular interface
and exits it through another interface can be limited with the „out.
..limit‟
parameters in the „qos‟ interface, where 
 is one of the following: default, eth0,
mesh0, wlan1, wlan2, wlan3, wlan4; and  is one of the following: default, eth0, local,
TR0153 Rev. D2
98
EnRoute50x/51x User’s Guide
mesh0, wlan1, wlan2, wlan3, wlan4. The „out.default.default.limit‟ value is applied to interfaces
that have the „out.
..limit‟ parameter set to „inherit‟ or is left blank.
The example below shows how to limit the maximum output rate of data from wlan1, wlan2,
wlan3, and wlan4 through the mesh0 interface to 2 Mbps, 1 Mbps, 512 kbps, and 256 kbps,
respectively.
> use qos
qos> set out.mesh0.wlan1.limit=2048
qos> set out.mesh0.wlan2.limit=1024
qos> set out.mesh0.wlan3.limit=512
qos> set out.mesh0.wlan4.limit=256
Traffic type limits can be set with the „out.
...limit.‟
parameters in the „qos‟ interface, where 
 is one of the following: default, eth0,
mesh0, wlan1, wlan2, wlan3, wlan4;  is one of the following: default, eth0, local,
mesh0, wlan1, wlan2, wlan3, wlan4;  is one of the following: „vo‟, „vi‟, „be‟, „bk‟
(see Table 15 for description of traffic types).
The example below shows how to limit the maximum output rate of voice, video, best effort,
and background traffic from wlan1 through the mesh0 interface to 256 kbps, 1 Mbps, 256 kbps,
and 256 kbps, respectively.
> use qos
qos> set out.mesh0.wlan1.vo.limit=256
qos> set out.mesh0.wlan1.vi.limit=1024
qos> set out.mesh0.wlan1.be.limit=256
qos> set out.mesh0.wlan1.bk.limit=256
Web GUI
The interface- and traffic-based Output Limit parameters can be set via the web interface
under the “QoS” tab on the “QoS” page (see Figure 43).
13.3
Rate Reservation
Rate reservation is used to guarantee bandwidth for certain types of traffic. Rate reservations
can be made for traffic based on:
The traffic input and output interfaces
The traffic type, input interface, and output interface
TR0153 Rev. D2
99
EnRoute50x/51x User’s Guide
For rate reservations to be enforced, a rate limit must be set for the traffic type that
the reservation is made for. Setting a rate limit for a broader traffic type, of which the
one the reservation is made for is a subset, is also acceptable. For example, when
making a rate reservation for voice traffic from wlan1 to mesh0
(„out.mesh0.wlan1.vo.reserve‟), a limit must be set with „out.mesh0.limit‟,
„out.mesh0.wlan1.limit‟, or „out.mesh0.wlan1.vo.limit‟.
Rate reservations guarantee bandwidth for a particular traffic type, but if no such traffic is
present, the bandwidth reserved will be returned to the pool of available bandwidth for other
traffic types to use. The points at which rate reservations can be made are shown in Figure 46.
These points are similar to where rate limits can be placed, except that rate reservations
require both an input and output interface, whereas rate limits can be made without specifying
an input interface.
Output
mesh0
eth0
wlan1
wlan2
wlan3
wlan4
wlan2
wlan3
wlan4
QoS Control Point
QOS
local
mesh0
eth0
wlan1
VI
VO
BK
BE
VI
VO
BK
BE
VI
VO
BK
BE
VI
VO
BK
BE
VI
VO
BK
BE
VI
VO
BK
BE
VI
VO
BK
BE
Input
Figure 46. Quality of Service rate reservation control points
All rate reservation parameter values are in kbps. If no rate reservation parameter is
set, rate reservation will be disabled for that interface or interface and traffic
combination.
A rate reservation, which guarantees a certain amount of bandwidth, can be made for traffic
that enters the EnRoute500 through a particular interface and exits it through another
interface. Rate reservations can also be set based on traffic type through an interface. Default
TR0153 Rev. D2
100
EnRoute50x/51x User’s Guide
value are applied to interfaces that have their bandwidth reservation parameters set to „inherit‟
or are left blank.
CLI
The parameters that are used to set these rate reservations are in the „qos‟ interface and are
of the form „out.
..reserve‟, where 
 is one of the following:
default, eth0, mesh0, wlan1, wlan2, wlan3, wlan4; and  is one of the following:
default, eth0, local, mesh0, wlan1, wlan2, wlan3, wlan4.
Typically, most rate reservations will involve reserving bandwidth for traffic from a particular
client interface to the mesh0 interface. The example below shows how to reserve differing
amount of bandwidth on mesh0 for traffic originating from the wlan1, wlan2, wlan3, and wlan4
interfaces.
> use qos
qos> set out.mesh0.wlan1.reserve=2048
qos> set out.mesh0.wlan2.limit=1024
qos> set out.mesh0.wlan3.limit=512
qos> set out.mesh0.wlan4.limit=256
A rate reservation for a certain type of traffic that enters the EnRoute500 through a particular
interface and exits it through another interface can be set with the „out.
...reserve.‟ parameters in the „qos‟ interface, where 
 is one of the
following: default, eth0, mesh0, wlan1, wlan2, wlan3, wlan4;  is one of the following:
default, eth0, local, mesh0, wlan1, wlan2, wlan3, wlan4;  is one of the following:
„vo‟, „vi‟, „be‟, „bk‟ (see Table 15 for description of traffic types).
The „out.default.default.limit‟ value is applied to interfaces that have the „out.
..reserve‟ parameter set to „inherit‟ or is left blank.
The example below shows how to reserve bandwidth for voice, video, best effort, and
background traffic from wlan1 through the mesh0 interface to 512 kbps, 1 Mbps, 256 kbps, and
128 kbps, respectively.
> use qos
qos> set out.mesh0.wlan1.vo.reserve=512
qos> set out.mesh0.wlan1.vi.reserve=1024
qos> set out.mesh0.wlan1.be.reserve=256
qos> set out.mesh0.wlan1.bk.reserve=128
Web GUI
The rate reservation parameters can be set via the web interface under the “QoS” and
“Advanced QoS” tabs on the “QoS” page (see Figure 43 and Figure 44).
TR0153 Rev. D2
101
EnRoute50x/51x User’s Guide
14 Enabling VLAN Tagging
The EnRoute500 supports VLAN tagging, with each client interface capable of supporting a
different VLAN tag. If VLAN tagging is enabled for an interface, client devices that connect to
the interface must be capable of receiving VLAN-tagged frames.
14.1
Client Interface Configuration
VLAN tagging can be independently controlled on each client interface (eth0, wlan1-4). The
Enable VLAN parameters for the „eth0‟, „wlan1‟, „wlan2‟, „wlan3‟, and „wlan4‟ interfaces controls
the state of VLAN tagging.
VLAN tagging must be enabled on the backhaul Ethernet interface on a mesh
cluster‟s gateway for VLAN tags to be included in data frames sent to the WAN. See
section 14.2 for more details.
The VLAN ID value for each client interface is set with the VLAN ID parameter for each
interface. The VLAN ID must be in the range from 0 to 4095. Note that 0 and 4095 are
reserved values and 1 is the default VLAN ID. There are no restrictions on VLAN IDs for
different interfaces or nodes having to match or be different.
CLI
The example below shows how to enable VLAN tagging on the „wlan1‟ interface and set the
VLAN ID to 12 using the parameters „vlan.enable‟ and „vlan.id‟ in the „wlan1‟ interface.
> use wlan1
wlan1> set vlan.enable=yes
> use wlan1
wlan1> set vlan.id=12
Web GUI
The VLAN Enable and VLAN ID parameters can be set via the web interface under the
“wlanN” tabs on the “Wireless Interfaces” page and on the “Wired/Backhaul Interface” page
(see Figure 47).
TR0153 Rev. D2
102
EnRoute50x/51x User’s Guide
Figure 47. Configuring VLAN for access point interfaces
14.2
Gateway Configuration
For VLAN tags to be preserved on traffic that exits a mesh cluster, VLAN support must be
enabled for the Ethernet interface on the mesh cluster‟s gateway node. The Enable VLAN
parameter for the Wired/Backhaul interface controls the state of VLAN tagging. If VLAN
tagging is enabled on the gateway‟s interface to the WAN, all outbound traffic will have its
VLAN tags preserved. If VLAN tagging is disabled for the backhaul interface, all VLAN tags will
be stripped from frames entering the mesh cluster.
When VLAN is enabled for the backhaul interface, data frames forwarded by the gateway to
the WAN will preserve their existing VLAN tag, if they have one. Frames that do not have a tag
will be tagged with the default VLAN ID for the gateway‟s Ethernet interface. The VLAN ID
must be in the range from 0 to 4095. Note that 0 and 4095 are reserved values and 1 is the
default VLAN ID.
CLI
The example below shows how to enable VLAN tagging on the backhaul interface on a
gateway node using the „vlan.enable‟ parameter in the „eth0‟ interface.
> use eth0
eth0> set vlan.enable=yes
TR0153 Rev. D2
103
EnRoute50x/51x User’s Guide
The example below shows how to set the VLAN ID for the backhaul Ethernet interface using
the „vlan.id‟ parameter in the „eth0‟ interface.
> use eth0
eth0> set vlan.id=1
Web GUI
The backhaul VLAN parameters are set on the “Wired/Backhaul Interface” page as shown in
Figure 48.
Figure 48. Configuring VLAN for backhaul interface
TR0153 Rev. D2
104
EnRoute50x/51x User’s Guide
15 Integration with Enterprise Equipment
The EnRoute500 supports authentication, accounting, and monitoring services that easily
integrate with enterprise equipment. In this section the following topics are described:
Splash pages
Backhaul health monitoring
Layer 2 client emulation
15.1
Configuring Splash Pages
The EnRoute500 supports splash pages, which can be used to restrict access to the mesh
network and provide information to users that connect to the mesh. When a user connects
through a client interface to an EnRoute500 with splash page support enabled, the splash
page for the appropriate interface will be displayed and the user will be restricted from
accessing other destinations on the Internet until having logged in. The splash page can
require the user to enter logon credentials or simply click a button to complete the login
process.
To use splash pages, a number of URLs for login, successful login, and failed login must be
specified. A RADIUS server that provides authentication services may also need to be
specified.
15.1.1
Enabling Splash Pages
The enabling of splash pages can be controlled on a per-interface basis. Two splash page
mode are supported – one which requires clients to login in to gain access to the network and
another which requires them to simply click on a button on the web page to proceed.
CLI
Enable or disable splash pages with the „splash.enable.wlanN‟ parameters in the „sys‟
interface. For a splash page to be displayed on an interface, the appropriate parameter must
be set to „yes‟. The example below illustrates how to set the „splash.enable.wlan1‟ parameter
in the „sys‟ interface to enable splash pages for the wlan1 interface.
> use sys
sys> set splash.enable.wlan1=yes
Use the „splash.auth.server.wlanN.enable‟ parameters in the „sys‟ interface to select whether a
user is required to provide login credentials for a particular interface. The example below
TR0153 Rev. D2
105
EnRoute50x/51x User’s Guide
illustrates how to set the parameter for the wlan1 interface such that a user will be required to
login to access the network.
> use sys
sys> set splash.auth.server.enable.wlan1=yes
Web GUI
Splash pages can be enabled on a per-interface basis on the “Splash Pages” sub-tab under
the “AAA” tab on the “System Parameters” page of the web interface (see Figure 49). Setting
whether client login is required can also be set on this page with the “Require Login”
parameter.
Figure 49. Splash page configuration
TR0153 Rev. D2
106
EnRoute50x/51x User’s Guide
15.1.2
Configuring Splash URLs
The URL that a user is redirected to for login purposes can be individually configured for each
client interface that supports splash pages (wlan1-4). URLs for successful login, failed login,
and error conditions can also be specified for each interface.
The „login URL‟ parameter sets the URL that a user is redirected to when they attach to the
interface and have not yet been authenticated. This parameter should not be left blank if
splash pages are enabled for the interface. No client would be able to access the network
through the interface if the login URL parameter does not point to a valid URL.
The „success URL‟ parameter sets the URL that a user is redirected to when they have
successfully logged in. If this variable is left blank, a default page that indicates login success
will be displayed.
The „fail URL‟ parameter sets the URL that a user is redirected to when a login attempt fails. If
this variable is left blank, a default page that indicates login failure will be displayed.
The „error URL‟ parameter sets the URL that a user is redirected to when a login error has
occurred. For example, this page would be displayed if a valid authentication server could not
be reached. If this variable is left blank, a default page that indicates an error has occurred will
be displayed.
CLI
The „splash.url..login‟ parameters in the „sys‟ interface, where  is either „wlan1‟,
„wlan2‟, „wlan3‟, or „wlan4‟, set the login URLs. The „splash.url..success‟ parameters in
the „sys‟ interface, where  is either „wlan1‟, „wlan2‟, „wlan3‟, or „wlan4‟, set the success
URLs. The „splash.url..fail‟ parameters in the „sys‟ interface, where  is either „wlan1‟,
„wlan2‟, „wlan3‟, or „wlan4‟, set the fail URLs. The „splash.url..error‟ parameters in the
„sys‟ interface, where  is either „wlan1‟, „wlan2‟, „wlan3‟, or „wlan4‟, set the error URLs
The example below shows how the „wlan1‟ and „wlan2‟ interfaces can be set to use different
URLs for the login process.
> use sys
sys> set splash.url.wlan1.login=http://server.domain.com/wlan1_login.htm
sys> set splash.url.wlan1.success=http://server.domain.com/wlan1_success.htm
sys> set splash.url.wlan1.fail=http://server.domain.com/wlan1_fail.htm
sys> set splash.url.wlan1.error=http://server.domain.com/wlan1_error.htm
sys> set splash.url.wlan2.login=http://server.domain.com/wlan2_login.htm
sys> set splash.url.wlan2.success=http://server.domain.com/wlan2_success.htm
sys> set splash.url.wlan2.fail=http://server.domain.com/wlan2_fail.htm
sys> set splash.url.wlan2.error=http://server.domain.com/wlan2_error.htm
TR0153 Rev. D2
107
EnRoute50x/51x User’s Guide
Web GUI
All of the splash page-related URLs can be set on the “Splash Pages” sub-tab under the “AAA”
tab on the “System Parameters” page of the web interface (see Figure 49).
15.1.3
Sample HTML Code for Splash Pages
The login HTML page must contain specific form information as shown in the sample code in
Figure 50 and Figure 51. Figure 50 contains the code required for an interface that requires a
login. Figure 51 contains code for a login page that the user just clicks through to unlock
network access.
The critical lines in Figure 50 are 6, 12, 15, and 19. The „action‟ value in line 6 of Figure 50
must point to a server name for which there is a DNS proxy entry on the local node and the
last part of it must be „/radius/login.cgi‟. The DNS proxy entry, which will be different for each
node in the network, must be mapped to one of the node‟s IP addresses (see section 6.7 for
more information on DNS proxy configuration).
The example below shows how to configure the DNS proxy assuming the login page redirects
to the host „redirect.domain.com‟ and the IP address of the wlan1 interface is 10.1.2.1.
> use sys
sys> set dnsproxy.enable=yes
sys> set dnsproxy.hosts=”dns.proxy.name.here=10.1.2.1”
The DNS proxy setting is used in conjunction with the splash pages to ensure that a
common login URL can be used on all nodes. The DNS proxy entry directs the
results of the login process to the right location – that is, the EnRoute500 that the
client device is connected to.
The login page must also contain the „input‟ fields on lines 12, 15, and 19. These are used to
allow a user logging in to provide their username and password, and to submit them. The
names of these input fields, „username‟, „password‟, and „login‟, must not be changed.
TR0153 Rev. D2
108
EnRoute50x/51x User’s Guide
10
11
12
13
14
15
16
17
18
19
20
21
22






Welcoming text or 'Terms of Service' could go here. 



 Username: 
 
 

 Password: 
  






Figure 50. Sample HTML code for login web page
If the splash page is not configured to require a user to provide login credentials, the
requirements for the login page are slightly different, as shown in Figure 51. The page must
still contain a form definition similar to that on line 6 in Figure 51. The „action‟ value must be set
to point to a proxied server name, just as for the case where a user is required to provide login
credentials. The last part of the „action‟ value must be „/splash/nologin.cgi‟. Also, a button with
the name „login‟ must be defined, as shown on line 8 of Figure 51.
10
11






Welcoming text or 'Terms of Service' could go here.





Figure 51. Sample HTML code for web page when authentication is disabled
15.1.4
Configuring the Authentication Server
A RADIUS authentication server must be specified when the splash page is enabled for an
interface and login is required. The following parameters must be specified:
the server address – can be either a hostname or and IP address
TR0153 Rev. D2
109
EnRoute50x/51x User’s Guide
the port on the server that the RADIUS server is listening on
the shared secret – must be a string of alphanumeric characters that is 32 characters or
less in length.
CLI
The
„splash.auth.server..host‟,
„splash.auth.server..port‟,
and
„splash.auth.server..secret‟ parameters in the „sys‟ interface, where  is either
„wlan1‟, „wlan2‟, „wlan3‟, or „wlan4‟, specify the authentication server to use. The example
below shows how to configure the authentication server for interfaces „wlan1‟ and „wlan2‟.
> use sys
sys> set splash.auth.server.wlan1.host=auth1.yourserverhere.com
sys> set splash.auth.server.wlan1.port=1812
sys> set splash.auth.server.wlan1.secret=authsecret
sys> set splash.auth.server.wlan2.host=auth2.yourserverhere.com
sys> set splash.auth.server.wlan2.port=1812
sys> set splash.auth.server.wlan2.secret=authsecret
Web GUI
The authentication server parameters can be set on the “Splash Pages” sub-tab under the
“AAA” tab on the “System Parameters” page of the web interface (see Figure 49).
15.1.5
Trusted MAC Addresses
A list of trusted MAC addresses, which do not require splash page authentication, can be
defined. When a device with one of these MAC addresses connects to a node, it will
automatically have full access to the WAN.
CLI
The list of trusted MAC addresses is set with the „splash.trusted_macs‟ parameter in the „sys‟
interface. The MAC addresses are specified as a list of 48-bit addresses separated by
commas. An example of setting this parameter is shown below.
> use sys
sys> set splash.trusted_macs="aa:bb:cc:00:00:01,aa:bb:cc:00:00:02"
Web GUI
The authentication server parameters can be set on the “Advanced Splash Pages” sub-tab
under the “AAA” tab on the “System Parameters” page of the web interface (see Figure 52).
The list of trusted MAC addresses is displayed on this page. To delete a trusted MAC from the
list, click on the “Delete MAC” button next to the MAC address.
TR0153 Rev. D2
110
EnRoute50x/51x User’s Guide
Figure 52. Adding trusted MAC addresses and accessible hosts
15.1.6
Bypass Splash Pages for Access to Specific Hosts
It is possible to specify a list of IP addresses that clients can access without the clients having
to view a splash screen.
CLI
The list of hosts that can be accessed without having to view a splash screen is set with the
„splash.bypass_hosts‟ parameter in the „sys‟ interface. The hosts are specified by their IP
addresses and must be separated by commas. An example of setting this parameter is shown
below.
> use sys
sys> set splash.bypass_hosts="1.1.1.1,2.2.2.2"
Web GUI
The IP addresses of hosts that can be accessed without having to view a splash screen can be
set on the “Advanced Splash Pages” sub-tab under the “AAA” tab on the “System Parameters”
page of the web interface (see Figure 52). The list of IP addresses of bypassed hosts is
displayed on this page. To delete an IP address from the list, click on the “Delete Host” button
next to the IP address.
TR0153 Rev. D2
111
EnRoute50x/51x User’s Guide
15.2
Layer 2 Emulation
Certain back-end systems (Internet gateways) use the MAC addresses of client devices for
authentication and accounting purposes. The EnRoute500 uses a layer 3 approach to mesh
routing, which means that the client MAC addresses are typically not provided to the back-end
servers. A layer 2 emulation mode can be enabled on the EnRoute500 to provide the client
MAC address information to back-end systems.
When the layer 2 emulation mode is enabled, a mesh cluster gateway will send Ethernet (layer
2) frames to the WAN using the MAC address of the device the packet originated from as the
source address. Mesh gateways will also act as proxies and forward packets with MAC
destination addresses of clients that are in the mesh cluster they service.
CLI
Layer 2 emulation is enabled with the „l2.client_mac_fwd‟ parameter in the „sys‟ interface. This
parameter should be set to the same value for all devices in a given mesh cluster. The
example below shows how to enable layer 2 emulation.
> use sys
sys> set l2.client_mac_fwd=yes
TR0153 Rev. D2
112
EnRoute50x/51x User’s Guide
16 Firmware Management
The EnRoute500 supports secure remote firmware upgrade.
16.1
Displaying the Firmware Version
CLI
Firmware version information is available in the „version‟ interface. The example below shows
how to display the current firmware version.
> use version
version> get release
release = ENROUTE500_20060419_00_00_0133
Web GUI
The firmware version is also displayed at the top of the “Status” page accessible via the web
interface.
16.2
Upgrading the Firmware
Contact Tranzeo for instructions on upgrading the EnRoute500‟s firmware.
TR0153 Rev. D2
113
EnRoute50x/51x User’s Guide
17 Glossary
ACL
Access Control List
AP
Access Point
CLI
Command line interface
ESSID
Extended Service Set Identifier
LAN
Local-Area Network
Mesh cloud
A group of EnRoute500 nodes configured as one or more clusters
Mesh cluster
A group of two or more EnRoute500 nodes with at least one
configured as a gateway
Mesh gateway
A mesh node that, in addition to relaying traffic between neighboring
mesh nodes and supporting wireless clients through its built-in APs,
acts as the layer 3 gateway for a mesh cluster
Mesh node
A single EnRoute500 that is part of a mesh cluster
Mesh repeater
A mesh node that relays traffic to neighboring mesh nodes and
supports wireless and wired clients.
NAT
Network Address Translation
PoE
Power over Ethernet
QoS
Quality of Service
RSSI
Received signal strength indicator
VLAN
Virtual Local-Area Network
VPN
Virtual Private Network
WAN
Wide-Area Network
WLAN
Wireless Local-Area Network
WPA
Wi-Fi Protected Access
WPA-PSK
Wi-Fi Protected Access Pre-Shared Key
TR0153 Rev. D2
114

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 114
Language                        : en-US
Tagged PDF                      : Yes
Author                          : Fredric Newberg
Creator                         : Microsoft® Office Word 2007
Create Date                     : 2007:05:24 22:39:52
Modify Date                     : 2007:05:24 22:39:52
Producer                        : Microsoft® Office Word 2007

EXIF Metadata provided by EXIF.tools