Triamp Technology BLUETOOTH Bluetooth Car Kit User Manual Installation Guide draft4 b

Download:
Mirror Download [FCC.gov]
Document ID	352922
Application ID	v2rsnfeXoMcRzHXHmucHxg==
Document Description	Installatio manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	5.83kB (72870 bits)
Date Submitted	2003-09-03 00:00:00
Date Available	2003-09-03 00:00:00
Creation Date	2003-08-08 12:11:30
Producing Software	Acrobat PDFWriter 5.0 for Windows
Document Lastmod	0000-00-00 00:00:00
Document Title	穨Installation Guide_draft4_b.doc
Document Creator	穨Microsoft Word
Document Author:	穨SS

This quick guide demonstrates how to set up and install the Bluetooth Wireless Car Kit into a vehicle. For
more detailed information about the use and functions of this device, refer to the user’s manual.
Identifying Components
Unpack the Car Kit package and check it contains the following components.
•
•
•
•
•
One junction box
One control module
One multi-directional microphone
One speaker with mounting bracket
One set of power cables
If any items are missing or damaged, contact your dealer.
A.
Installing the Junction Box
The Car Kit is designed to work with the 12-volt power supply of the vehicle. Refer to the following to install
the junction box in a vehicle.
1.
2.
B.
Locate a suitable place inside the car to mount the junction box. Select a dry place that avoids
excessive heat and mechanical vibration. Ideally, the junction box should be hidden from view,
but still easily accessible.
Note: Make sure that the cables are long enough to support the location of the junction box. If
the cables are not long enough, do not lengthen the cables; relocate the junction box.
Use two screws (not included) to fasten the junction box in place.
Connecting the Power Supply
The following illustration demonstrates how to connect the Car Kit’s power cables to the vehicle’s
electrical system.
Yellow cable
To car radio
mute (PNP 300mA)
Red cable
To battery + 12V
Power cables
Blue cable
To ignition
Black cable
GND
Important!
The Blue cable must be connected to the 12V switched to enable the Car Kit to go into standby mode.
Do not connect the Blue cable to the +12V permanent. Doing so may discharge the battery of the
vehicle and prevent the Car Kit from being reset.
C.
Connecting Accessories
The following illustration shows where to connect accessory devices.
Junction box
Control module
Microphone
Speaker
D.
Control module
The control module should be located within reach and view of the
driver.
Speaker
For best reception, the speaker should be mounted at least 80 cm (30
inches) from the Car Kit’s microphone.
Microphone
Ideally, the microphone should be located in front of the user and
above waist height.
Installing the microphone
Before installing the microphone, take note of the following:
• Make sure that the cable can reach from the microphone to the speaker. If the cable is
too short, relocate the microphone. Do not lengthen the cable.
•
The supplied microphone is uni-directional. For best results, place the microphone in
front of the person talking. It has a reception angle of 60 degrees, and is most effective
within a 60 cm radius.
Using the microphone stand
Find a suitable place for the microphone stand. Remove dust and grease from the surface.
1. Remove the protective cover from one
side of the double-sided tape and
press it firmly onto the bottom of the
stand.
2.
Remove the other protective cover,
and firmly press the stand in place.
3.
Push the microphone into the stand.
Using the microphone visor clip
1.
Slide the visor clip onto the visor with
the microphone clip facing down.
2.
Push the microphone into the
mounting clip.
Upgrading Firmware (optional)
It may be possible to use future phone models by upgrading the firmware in the Car Kit. Firmware is
upgraded via the serial port located on the back of the junction box.
Serial port
When upgrading, follow the installation instructions that are provided with the firmware upgrade.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Page Count                      : 3
Creator                         : .穨.Microsoft Word
Create Date                     : 2003:08:08 12:11:30
Title                           : .穨.Installation Guide_draft4_b.doc
Author                          : .穨.SS
Producer                        : Acrobat PDFWriter 5.0 for Windows

EXIF Metadata provided by EXIF.tools