Tyco Safety Canada 00NB9001 Receiver User Manual Users guide

Digital Security Controls Ltd. Receiver Users guide

UserManual.wiki >

Tyco Safety Canada >

00NB9001 User Manual >

Users guide HTML Version

1. Users guide
2. Installation guide

Users guide

Security Products

WARNING

This manual contains information on

limitations regarding product use and

function and information on the

limitations as to liability of the

manufacturer. The entire manual should

be carefully read.

NT9010

NT9010NT9010

NT9010

User’s

Guide

FCC COMPLIANCE STATEMENT

CAUTION: Changes or modifications not expressly approved

by Digital Security Controls Ltd. could void your authority to

use this equipment.

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communica-

tions. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of

the following measures:

• Re-orient the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

• Consult the dealer or an experienced radio/television techni-

cian for help.

The user may find the following booklet prepared by the FCC use-

ful: “How to Identify and Resolve Radio/Television Interference

Problems”. This booklet is available from the U.S. Government

Printing Office, Washington D.C. 20402, Stock # 004-000-00345-

IMPORTANT INFORMATION

This equipment complies with Part 68 of the FCC Rules. On

the side of this equipment is a label that contains, among

other information, the FCC registration number of this equip-

ment.

Notification to Telephone Company The customer shall notify

the telephone company of the particular line to which the

connection will be made, and provide the FCC registration

number and the ringer equivalence of the protective circuit.

FCC Registration Number: F53CAN-xxxxx-AL-E

Ringer Equivalence Number: 0.xB

USOC Jack: RJ31X

Telephone Connection Requirements Except for the telephone

company provided ringers, all connections to the telephone net-

work shall be made through standard plugs and telephone com-

pany provided jacks, or equivalent, in such a manner as to allow

for easy, immediate disconnection of the terminal equipment.

Standard jacks shall be so arranged that, if the plug connected

thereto is withdrawn, no interference to the operation of the equip-

ment at the customer’s premises which remains connected to the

telephone network shall occur by reason of such withdrawal.

Incidence of Harm Should terminal equipment or protective cir-

cuitry cause harm to the telephone network, the telephone com-

pany shall, where practicable, notify the customer that temporary

disconnection of service may be required; however, where prior

notice is not practicable, the telephone company may temporarily

discontinue service if such action is deemed reasonable in the

circumstances. In the case of such temporary discontinuance,

the telephone company shall promptly notify the customer and

will be given the opportunity to correct the situation.

Additional Telephone Company Information The security con-

trol panel must be properly connected to the telephone line with a

USOC RJ-31X telephone jack.

The FCC prohibits customer-provided terminal equipment be

connected to party lines or to be used in conjunction with coin

telephone service. Interconnect rules may vary from state to state.

Changes in Telephone Company Equipment or Facilities The

telephone company may make changes in its communications

facilities, equipment, operations or procedures, where such

actions are reasonably required and proper in its business.

Should any such changes render the customer’s terminal equip-

ment incompatible with the telephone company facilities the cus-

tomer shall be given adequate notice to the effect modifications

to maintain uninterrupted service.

Ringer Equivalence Number (REN) The REN is useful to deter-

mine the quantity of devices that you may connect to your tele-

phone line and still have all of those devices ring when your

telephone number is called. In most, but not all areas, the sum of

the RENs of all devices connected to one line should not exceed

five (5.0). To be certain of the number of devices that you may

connect to your line, you may want to contact your local tele-

phone company.

Equipment Maintenance Facility If you experience trouble with

this telephone equipment, please contact the facility indicated

below for information on obtaining service or repairs. The tele-

phone company may ask that you disconnect this equipment

from the network until the problem has been corrected or until you

are sure that the equipment is not malfunctioning.

Digital Security Controls Ltd. 160 Washburn St., Lockport, NY

14094

Quick Reference Guide

The following chart lists the basic functions of your system, and the keys to press for each

function. Refer to the listed page number for more information.

NOTE: Some functions may not be available on your system. Ask your installer for

more information.

To do this: Press this: Page:

Turn on system (Away): [access code], leave through entry/exit door 9

OR press (if enabled)

Turn on system (Stay):........................ [access code], do not leave premises 12

OR press (if enabled)

Turn off system:................................. [access code] 10

Turn on system (No Entry Time): ........ [access code] 13

Turn on system (Quick, if enabled): .... (from Ready state) 12

Turn on rest of system (if Stay armed): OR press (if enabled) 12

Exit premises when system on: .......... OR press (if enabled) 14

Turn off zones (Bypass): ..................... [two-digit zone number(s)], to exit 18

Test system ........................................ [master code] 20

Send Fire message: ............................ (press & hold for 2 seconds, if enabled) 17

Send Auxiliary message: .................... press & hold for 2 seconds, if enabled) 17

Send Panic message: ......................... (press & hold for 2 seconds, if enabled) 17

Silence fire alarm: .............................. [access code] 15

Silence intrusion alarm: ..................... [access code] 16

Turn door chime on/off: ...................... to toggle on or off 22

OR press (if enabled)

Check alarm memory: ....................... 16

Check troubles .................................. 19

Set time and date:............................. [master code] 21

Table of Contents

WLS9001 Control Unit Features 2

About This Guide 4

Introduction 5

How Your System Works ..................................5

IMPORTANT NOTICE ........................................5

Fire Detection ...................................................6

Testing .............................................................6

Remote Monitoring ..........................................6

Maintenance ....................................................6

Using Your WLS9000 System 7

Operating the System from the

WLS9001 Control Unit .....................................7

Operating the System from a Telephone ...........7

Receiving Incoming Calls ..................................8

Recording and Playing Voice Memos ................8

Turning Your System On (Arming) and Off

(Disarming) 9

Turning On Your System ..................................9

Turning Off Your System ...............................10

Other Ways to Turn Your System On ..............10

Turning On Your System When Everyone is

Away (Away Mode) ........................................11

What to do if the Siren Sounds Immediately

After You Exit .................................................11

Turning On Your System While You Are

At Home (Stay Mode) .....................................12

Turning On Your System With No Access Code

(Quick Arm) ....................................................12

Turing On Your System with No Entry Time ....13

Turning On Your System Automatically

(Automatic Arming) ........................................13

Exiting When the System is On (Quick Exit) .....14

Dealing With Alarms and Emergencies 15

Fire Alarms .....................................................15

Intrusion (Burglary) Alarms ............................. 16

Central Station Talk/Listen-in .......................... 16

Checking Alarms in Memory .......................... 16

Calling for Help .............................................. 17

Using Advanced Functions 18

Turning Off Part of Your System

(Bypassing Zones) ........................................... 18

Checking Trouble Conditions ......................... 19

Testing Your System ...................................... 20

Allowing Computer Access to Your System .... 20

Customizing Your System 21

Programming Access Codes ........................... 21

Setting the Time and Date ............................. 21

Turning the Door Chime On or Off ................ 22

Changing WLS9001 Speaker Loudness .......... 22

Changing Telephone Prompt Loudness .......... 22

Fire Safety 23

Household Fire Safety Audit ........................... 23

Fire Escape Planning ....................................... 23

Replacing Batteries 25

Tips for Buying Batteries ................................. 25

Door/Window Contacts ................................. 26

Motion Detectors ........................................... 26

Handheld Keypad .......................................... 26

Glassbreak Detector ....................................... 27

Smoke Detectors ............................................ 27

Wireless Keys ................................................. 27

Panic Pendants ............................................... 27

After Installing New Batteries ......................... 27

Glossary 28

System Information 30

Index 32

NT9010 Control Unit Features

This is the NT9010 control unit. This unit controls and monitors all devices on your NT9010 security

system. You can access all system functions using the buttons on the NT9010. In addition, the NT9010

provides easy to understand help on using the system through voice prompts. Please see the descrip-

tions at right for information on the features of the NT9010 control unit.

NT9010 Control Unit Features

➊ Microphone

You can use the microphone to record a voice

memo on the NT9010. To record a memo, press

and hold the Record button for two seconds,

then talk into the microphone. When you are

finished recording, press . To play the memo,

press and hold the Playback button for two sec-

onds.

If central station talk/listen-in is enabled on your

system, the microphone will also allow you to

talk to your central station operator when this

feature is active.

➋ Siren

The NT9010 uses the siren to warn you about

fire and burglary alarms.

➌ Speaker

The NT9010 uses the speaker to broadcast sys-

tem announcements, instructions, recorded

memos, and alarms.

➍ Status Lights:

The NT9010 status lights provide you with

instant visual feedback on the status of your

security system.

Green Ready Light

If the Ready light is ON, the system is ready to be

turned on. You will not be able to turn the sys-

tem on unless the Ready light is ON (see “Turn-

ing On Your System” on page 9).

If the Ready light is flashing, someone has

recorded a voice memo on the NT9010. Press

and hold the Playback button for two seconds to

listen to the recording.

Red Armed Light

If the Armed light is ON, the system has been

turned on successfully.

Orange System Light

If the System light is ON, one or more of these

conditions could be present on the system:

System Troubles (See “Checking Trouble Condi-

tions” on page 19).

Alarms in Memory (See “Turning Off Your Sys-

tem” on page 10).

Zones Bypassed (turned off) (See “Turning Off

Part of Your System (Bypassing Zones)” on page

18).

Programming. The System light will flash when

you are programming access codes, or perform-

ing other programming functions.

➎ Emergency Keys:

In an emergency, you can use these keys to

instantly contact your central station:

Press both * keys for two seconds to send a

Fire message.

Press both * Keys for two seconds to send an

Auxiliary message.

Press both * Keys for two seconds to send a

Panic message.

IMPORTANT NOTE: *The Fire, Auxiliary and

Panic keys will NOT function unless pro-

grammed by the installer. If these keys are in

service and the installer has enabled audible

feedback, holding down both keys for two

seconds will cause the keypad sounder to

beep indicating that the input has been

accepted and sent.

➏ Number Pad:

Use the number pad to enter your access code

and system commands. To select a function

press . To exit a function press .

➐ Function Buttons:

If your installer has enabled them, you can use

the function buttons to access the stay, away,

door chime, quick exit, status, volume control,

memo record, and memo playback features. To

use a feature, press and hold one of the buttons

for two seconds. Refer to this Guide for more

information on these features.

About This Guide

This NT9010 User’s Guide is for anybody using a NT9010 Security System. The

NT9010 has many useful features. Read this guide thoroughly to learn how to use

your security system. Ensure that all users of this system are equally instructed in its

use.

Important information about fire and burglary alarms is in section 3 on

page 15. Read this section carefully!

This guide provides step-by-step instructions for each function. Each key you need

to press will be indicated by its symbol (e.g. ).

For some functions, you will need to enter your access code (indicated by [access

code]). To program other access codes, or to perform advanced functions, you will

need to enter or your master code (indicated by [master code]). You can also use

the master code to turn the system on and off.

The NT9010 control unit and its lights and functions are described on pages 2 and

The Quick Reference Guide inside the front cover shows you the commands

required to access basic system functions, and the page number each function is

described on.

See the Glossary on page 28 to learn more about words used in this manual.

Fill out the “System Information” page with all of your zone information

and access codes, and store this manual in a safe place for future reference.

Section 1: Introduction

Your installer has set up your system with your home or business in mind. You may

not need all of the features described in this manual. Your installer will only turn

on the features that you need, and should explain all the active features to you. If

you have any questions about which features are included on your system, please

ask your installer.

How Your

System Works

Your security system is made up of a DSC NT9010 control unit, and various detec-

tors and wireless devices.

The control unit is the “brain” of your security system. It controls and checks all

the detectors, and communicates with the central station (if remote monitoring is

enabled). You will access system functions with your NT9010 control unit, which is

described on pages 2 and 3 of this manual. Each NT9010 has a microphone, siren,

speaker, number pad, emergency keys, and eight function keys.

Using the NT9010 you can send commands to the system and check the current

system status. Your installer will mount the NT9010 in a convenient location inside

your premises.

Your security system can provide up to three kinds of monitoring: intrusion, fire,

and emergency.

The security system has several zones (monitored areas). Each of these zones will

be connected to a detector (motion detector, glassbreak detector, door contact,

etc.). If a detector goes into alarm, the NT9010 will sound an alarm and may

announce the specific zone that caused the alarm (depending on how your

installer has programmed the system).

IMPORTANT

NOTICE

A security system cannot prevent emergencies. It is only intended to alert

you and – if included – your central station of an emergency situation.

Security systems are generally very reliable but they may not work under

all conditions and they are not a substitute for prudent security practices

or life and property insurance. Your security system should be installed

and serviced by qualified security professionals who should instruct you

on the level of protection that has been provided and on system opera-

tions. For important warnings and cautions, please see inside the back

cover.

Fire Detection This equipment is capable of monitoring fire detection devices such as smoke

detectors and providing a warning if a fire condition is detected. Good fire detec-

tion depends on having adequate number of detectors placed in appropriate loca-

tions. This equipment must be installed in accordance with NFPA 72 (N.F.P.A.,

Batterymarch Park, Quincey MA 02269). Carefully review Section 7:“Fire Safety”

on page 23.

NOTE: Your installer must enable the fire detection portion of this equip-

ment for it to work.

Te s t i n g To make sure your system continues to work as intended, you must test your sys-

tem weekly. Please refer to “Testing Your System” on page 20. If your system does

not work correctly, call your installer for service.

Remote

Monitoring

This system can send alarms, troubles and emergency messages over telephone

lines to a central station. If you accidentally initiate an alarm, immediately call the

central station to prevent an unnecessary response.

NOTE: Your installer must enable remote monitoring for it to work.

Maintenance With normal use, the system requires minimum maintenance. Note the following

points:

1. Do not wash the security equipment with a wet cloth. Light dusting with a

slightly moistened cloth should remove normal accumulations of dust.

2. Use the system test described in “Testing Your System” on page 20 to check the

battery condition of the NT9010 control unit. We recommend, however, that

the stand-by battery be replaced every three years.

3. For other system devices such as smoke detectors, passive infrared, ultrasonic

or microwave motion detectors or glassbreak detectors, consult the manufac-

turer’s literature for testing and maintenance instructions. For instructions on

replacing detector batteries, see “Replacing Batteries” on page 25.

Section 2: Using Your NT9010 System

Operating the

System from

the NT9010

Control Unit

The NT9010 control unit provides easy to understand help on using the system

through voice prompts.

If the system asks you to enter an access code, use the number pad on the unit to

enter your 4- or 6-digit code.

You can check the current status of your system by pressing and holding the Sta-

tus button for two seconds. The NT9010 will announce whether the system is cur-

rently on (armed), or off (disarmed), if any zones are currently open or bypassed

(turned off), and if there are any trouble conditions currently present on the sys-

tem.

Operating the

System from

a Telephone

If your installer has connected your NT9010 system to an incoming telephone line,

you can access the system using a local telephone (a telephone on your premise).

You may also be able to use the system from a remote telephone (a telephone not

on your premise), if your installer has turned on this feature.

Even though you can use a telephone to operate your system, the telephone will

not automatically display or indicate system status or zones in alarm. Therefore, it

is essential that you check the NT9010 control unit regularly for any changes in

system status.

CAUTION: For the security of your codes, DO NOT use a telephone with a

redial button to arm or disarm your system.

Local Telephone Access

Use this procedure to call your NT9010 system from a telephone that is on the

same telephone line. No dial-in is necessary.

1. Pick up the telephone handset - you will hear a dial tone.

2. Enter your 3-digit Telephone Access Code. The dial tone will stop and the sys-

tem will announce:

“Hello.”

3. The system may also say:

“Enter your access code.”

If so, enter your [access code].

4. The system announces one or more messages to advise you of its status. Follow

the voice prompts to use the system functions.

Remote Telephone Access

1. From any touch-tone telephone, dial the number of your premises. If you have

more than one telephone line, call the number of the line on which your

NT9010 has been installed.

2. After one ring, hang up. Wait 10 seconds then call again. On the second call,

the system will answer after one or two rings and announce:

“Hello.”

3. Enter your 3-digit Telephone Access Code within 10 seconds. If you wait longer

than 10 seconds, the system will automatically hang up.

4. The system will then prompt:

“Enter your access code.”

Enter your [access code] within 20 seconds. If you wait longer than 20 seconds,

the system will hang up. The system will also hang up if 3 incorrect access

codes are entered.

5. Once you have entered an access code, the system will announce one or more

messages to advise you of its status. Follow the voice prompts to use the sys-

tem functions.

NOTE: There is only one “Telephone Access Code”. It is programmed by

your installer. It is not the same as your 4- or 6-digit system access code,

which you also enter on your system keypad. More than one system access

code may be programmed for use by different users of your system (see

“Programming Access Codes” on page 21).

Receiving

Incoming

Calls

If you are accessing the NT9010 system over a local telephone at the same time as

someone calls you, the system will announce:

“Attention, you have an incoming call. To receive the call, press pound now.”

To answer the incoming call, press . If you do not press , you can continue

to use the system.

Recording and

Playing Voice

Memos

You can record a voice memo on the NT9010 control unit, so that you or another

person can listen to it later. To record a voice memo:

1. Press and hold the Record function button for two seconds. The NT9010 says

“Record memo now.”

2. Speak into the microphone (located in the top left corner of the unit). When

you have finished recording, press . The green Ready light flashes to indicate

a new memo has been recorded.

To listen to a voice memo:

1. Press and hold the Playback function button for two seconds. Once the memo has

been played, the green Ready light stops flashing, however the memo remains in

memory until a new one is recorded, or until the NT9010 loses all power.

2. If the memo is not for you, you can press to stop the playback. If you press

before the playback finishes, the Ready light will continue to flash.

Section 3: Turning Your System On

(Arming) and Off (Disarming)

This section describes how to turn your system on and off. Read this section care-

fully.

Tur ning On

Your System

1. Before you turn on your system, make sure that it is Ready. You can tell that the

system is ready when the green (Ready) light is ON. If the green light is not on,

see the Note below.

2. Enter your access code on the keypad. If you have entered the wrong code, the

keypad will sound one long beep - try again to enter the correct code.

When you enter a valid access code:

• The keypad sounds fast beeps.

• The red (Armed) light turns ON.

• The keypad starts to beep once every second. This tells you that the sys-

tem is turning on.

3. If you will be leaving, go out through the entry/exit door. Doing this tells the sys-

tem that you are away, and the system turns on completely.

If you will be staying, do not open the entry/exit door. This tells the system that

you are staying, and the system turns on only the perimeter areas.

NOTE: If the green (Ready) light is not on:

• Close all doors and windows

• Stop motion in all areas with motion detectors

If the orange (System) light is ON, check for possible trouble conditions (see

“Checking Trouble Conditions” on page 19), and check that no zones are

turned off unintentionally (see “Turning Off Part of Your System (Bypassing

Zones)” on page 18).

Tur ning Off

Your System

1. If you are outside, enter through the entry/exit door. The keypad beeps to

remind you to turn off the system.

NOTE: Entering by any other door will immediately cause an alarm.

If you are inside, go to the keypad (the keypad will not beep).

2. Enter your [access code]. If you have entered from outside, you must enter the

correct access code before the keypad stops beeping. If you do not enter a

valid access code during this time, the system will sound an alarm.

NOTE: If you have entered the wrong code the keypad will sound one long

beep - try again to enter the correct code.

As soon as you enter the correct code, the red (Armed) light turns OFF and the

keypad stops beeping.

3. If no alarms occurred while the system was on and there are no trouble condi-

tions present, the NT9010 will announce: “System is off. No alarms in mem-

ory.”.

If an alarm occurred while the system was on, the NT9010 will announce: “Sys-

tem is off. There are (number) alarms in memory: {Zone XX}.” See “Checking

Alarms in Memory” on page 16.

CAUTION: If you return and find that an alarm has occurred while you

were away, it is possible that an intruder may still be on the premises. Go to

a nearby safe location, and call your central station or the local authorities

to investigate. The alarm memory is cleared each time the system is turned

on, so any alarms showing have occurred only during the last time the sys-

tem was on.

Other Ways to

Tur n Your

System On

There are two basic methods for turning on your security system.

•Away: Use this method when everyone will be away from the premises. See

below.

•Stay: Use this method when one or more people will stay on the premises. See

page 12.

You can also use any of these methods to turn on your system (see pages 10 to

11):

•Quick Arming: Turn on your system without having to enter an access code.

Your installer must turn on this feature before it will work.

•“No Entry” Arming: Turn on your system with no entry time - use this method

when no one else will be entering the premises.

•Automatic Arming: The system will turn itself on at pre-set times. Your

installer must turn on this feature before it will work.

NOTE: When turning on your system from a remote telephone, the system

will automatically be in Stay mode. (See “Turning On Your System While You

Are At Home (Stay Mode)” on page 12.)

Turning Your System On (Arming) and Off (Disarming)

Tur ning On

Your System

When

Everyone is

Away (Away

Mode)

When you turn on your system using the Away method, both interior zones (e.g.

motion detectors) and perimeter zones (e.g. door and window contacts) will be

active and will cause an alarm to sound when opened.

1. Check that your system is ready (green Ready light is ON).

2. Enter your [access code]. As you enter each digit, the keypad sounder beeps.

If you entered the access code incorrectly, the keypad sounder buzzes steadily

for two seconds. Re-enter your access code correctly.

When you enter a valid access code:

• The keypad sounds fast beeps.

• The red (Armed) light turns ON.

• The exit time begins and the keypad beeps once every second until the

end of the exit time. The keypad beeps quickly for the last 10 seconds of

the exit time.

3. Exit the premises through the entry/exit door. Doing this tells the system that

you are away, and the system turns on all the interior zones.

At the end of the exit time, all keypad lights, except the red (Armed) light, turn

OFF. The system is now on.

NOTE: If the system announces that any zones are bypassed, or if the

orange (System) light is ON, there are one or more zones not turned on.

See “Turning Off Part of Your System (Bypassing Zones)” on page 18. If you turn

on the system with a zone bypassed or a trouble present, your security pro-

tection is reduced.

Away Button

You may also be able to quickly turn on your system in Away mode using the

“Away” button on your keypad. If your installer has programmed this button,

press and hold it for two seconds to turn on the system in Away mode.

What to do if

the Siren

Sounds

Immediately

After You Exit

Your installer will tell you if this feature has been enabled on your system.

In order to reduce false alarms, the system will notify you of an improper exit

when turning on the system in the Away mode. If you do not securely close the

entry/exit door during the exit time, the keypad will emit one continuous beep and

the siren will sound.

If this occurs:

1. Re-enter the premises.

2. Enter your [access code] to turn off the system. You must do this before the

entry time ends.

3. Turn the system on again, making sure to close the entry/exit door properly.

(See “Turning On Your System When Everyone is Away (Away Mode)”.)

Tur ning On

Your System

While You Are

At Home (Stay

Mode)

Use the Stay mode when you want to stay on the premises, but prevent unautho-

rized entry from outside. The system will only turn on the perimeter zones (e.g.

door and window contacts), and will leave the interior zones off (e.g. motion

detectors) so that you will be free to move around inside.

1. Check that your system is ready (green Ready light is ON)

2. Enter your [access code]. As you enter each digit, the keypad sounder beeps.

If you entered the access code incorrectly, the keypad sounder buzzes steadily

for two seconds. Re-enter your access code correctly.

When you enter a valid access code:

• The keypad sounds fast beeps.

• The red (Armed) light turns ON.

• The exit time begins and the keypad beeps once every second until the

end of the exit time. The keypad beeps quickly for the last 10 seconds of

the exit time.

3. DO NOT leave through the entry/exit door. This tells the system that you are

staying, and the system automatically turns off the interior zones.

At the end of the exit time, all keypad lights, except the red (Armed) and

orange (System) lights, turn OFF. The system is now on.

Re-activate bypassed zones

To turn on the rest of the system when it is in Stay mode:

1. Press . The interior zones are now on.

NOTE: When you have turned on the interior zones, you will not be able to

enter areas protected by motion detectors, or open doors and windows. To

access these areas, you must enter your [access code] and turn off the sys-

tem.

Stay Button

You may also be able to quickly Stay arm your system using the “Stay” function

button on your keypad. If your installer has programmed this button, press and

hold it for two seconds to turn your system on in Stay mode.

Tur ning On

Your System

With No

Access Code

(Quick Arm)

Your installer will tell you if the Quick Arm method will work on your system.

Using this method, you can quickly turn on your system without having to enter

an access code.

1. Check that the system is ready (green Ready light is ON)

2. Press .

• The keypad sounds fast beeps.

• The red (Armed) light turns ON.

• The exit time begins and the keypad beeps once every second until the

end of the exit time.

Turning Your System On (Arming) and Off (Disarming)

3. Go out through the entry/exit door. The system will be in Away mode. If you do

not exit, the system will be in Stay mode.

NOTE: Pressing will only turn on the system. To turn the system off,

you must enter a valid [access code]. See “Turning Off Your System” on page

10.

Turing On

Your System

with No Entry

Time

If you want to turn on the system, and no one else will be entering, you can

remove the entry time from zones that normally have one. If somebody enters

through any zone, the system will sound an instant alarm.

1. Check that your system is ready (green Ready light is ON)

2. Press , then your [access code].

• The red (Armed) light flashes as a reminder that the system is on and has

no entry time.

• The keypad sounds fast beeps.

3. The system is now in Stay mode.

Tur ning On

Your System

Automatically

(Automatic

Arming)

Your installer may have set up your system to turn on at a pre-set time. If auto-

matic arming has been set up, when the system reaches the pre-set autoarm time,

the keypad buzzers will sound for one minute.

During this one-minute warning time, you may be able to stop automatic arming

by entering your [access code]. Ask your installer for more information.

Your installer may have set up the system so that users with a master code can

change the autoarm time at the keypad. If so, master users will be able to turn the

automatic arming function on or off, and program the time at which the system

will automatically turn on each day.

To turn automatic arming on or off:

1. Press , then [master code].

2. Press to turn automatic arming on or off. The keypad will beep 3 times

when auto-arm is turned ON, and once when it is turned OFF.

3. When you are finished, press .

To change the autoarm time:

1. Press , then [master code].

2. Press .

3. Enter the autoarm time using the 24Hr format (0000 - 2359). For example, to

set the time for 1:00pm, enter (1300).

5. When you are finished, press twice.

NOTE: The system must have the correct time and date in order for the

autoarm feature to work. Please see“Setting the Time and Date” on page 21.

Exiting When

the System is

On (Quick

Exit)

Your installer will tell you if the Quick Exit feature will work on your system. You

can use the quick exit feature to leave while the system is on, without having to

turn your system off and on again.

To use the quick exit feature:

1. While the system is on, press .

2. The system will start a two-minute countdown, during which you may leave

through the entry/exit door.

NOTE: During this time, you may only open and close the entry/exit door

once. Once the door is closed the system will end the two-minute quick exit

time. If the door is opened again, or is not closed before the two-minutes

are up, or if another entry/exit door is opened, the entry time will begin.

Exit Button

If your installer has programmed the “Exit” function button, press and hold the

button for two seconds to activate the quick exit feature.

Section 4: Dealing With Alarms and

Emergencies

If you return and the siren is on, do not enter, but contact the local author-

ities from a nearby safe location.

Read this section carefully so that you will know what to do if your system goes

into alarm.

Your installer will tell you if fire detection equipment has been installed and

enabled on your system.

NOTE: A fire alarm always has priority over an intrusion (burglary) alarm.

Fire Alarms A pulsing siren means a fire alarm. If there is a fire, or if you are not sure, fol-

low your evacuation plan immediately (see “Fire Escape Planning” on page

23). The system may also announce the label for the zone(s) that triggered the

alarm, if programmed by the installer.

If remote monitoring is enabled, the system will send a fire message to the central

station. Your installer may have set up the keypad Fire keys and other fire equip-

ment to send a fire alarm message to the central station as soon as they are acti-

vated.

Your installer may have set up other equipment (e.g. smoke detectors) to have a

30 second delay before sending the alarm message to the central station. Your

installer will inform you how the equipment on your system operates. Equipment

that has been set up with a 30 second delay (e.g. smoke detectors) gives you time

to correct the problem before a false alarm is sent to the central station.

If there is no fire condition, to silence the fire alarm:

1. Press within 30 seconds of the beginning of the alarm. The fire alarm and

communication to the central station will be delayed for 90 seconds to give you

time to clear the smoke detector.

2. If the detector still detects smoke after 90 seconds, the alarm will sound again.

If there is no smoke, the system will return to normal.

3. If you do not press within the 30 second delay time, the system will send a

fire message to the central station (if remote monitoring is enabled on your sys-

tem). To silence the fire alarm after the 30 second delay has expired, enter your

[access code].

NOTE: If you suspect that a fire message has been transmitted, but there is

no fire condition, call the central station to avoid an unnecessary response.

NOTE: Your installer may have programmed the system to operate differ-

ently than described above. Ask your installer for more information

regarding your system’s operation.

Intrusion

(Burglary)

Alarms

A steady siren means an intrusion alarm. The system may also announce the label

for the zone(s) that triggered the alarm, if programmed by the installer.

To silence the alarm:

1. Enter your [access code].

2. If the alarm was unintentional, call your central station or local authorities

immediately to avoid an unnecessary response.

3. Check the alarm memory to see which zone caused the alarm.

Once the source of the alarm has been corrected, the system will return to the

Ready state.

Central

Station Talk/

Listen-in

If your installer has set up remote monitoring on your system, the talk/listen-in fea-

ture may also be available. If an alarm, or other programmed event occurs on your

system, this feature allows a central station operator to listen to what is happening

on the premises. The operator may also be able to talk to whoever is present,

depending on the type of event that has occurred. Ask your installer for more

information on this feature and how it works.

Checking

Alarms in

Memory

The alarm memory announcement tells you which zone (detector) caused the

alarm. The alarm memory is cleared each time the system is turned on. Any alarms

announced by the system have only occurred the last time the system was on.

CAUTION: If you return and find that there was an alarm while you were

away, it is possible that an intruder may still be on the premises. Go to a

nearby safe location, and call your central station or the local authorities to

investigate.

If an alarm occurred while the system was turned on, the NT9010 will announce:

“There are (number) alarms in memory: {Zone XX}.”.

1. To cancel the alarm memory announcement, press .

2. After the announcement is over, the system will return to the Ready state, but

the orange (System) light will be ON. To listen to alarms in memory again, press

. The NT9010 will announce the zones that were in alarm.

Dealing With Alarms and Emergencies

Calling for

Help

The NT9010 has three pairs of emergency keys. Using these keys you can send an

immediate Fire, Auxiliary or Panic message to your central station.

IMPORTANT:The Fire, Auxiliary and Panic keys will NOT function unless

turned ON by the installer. If your installer has turned these keys ON, and

enabled audible feedback, holding down the keys for two seconds will

cause the keypad sounder to beep indicating that the alarm input has been

accepted and transmission to the central station is underway.

From the NT9010 Control Unit

Press both keys for two seconds to send a Fire message, and to trigger a

fire alarm on the system.

Press both keys for two seconds to send an Auxiliary message.

Press both keys for two seconds to send a Panic message.

From Your Local Telephone

If local telephone access is available on your system, you can also:

• send a Fire message and trigger a fire alarm by pressing and holding for 2 sec-

onds the [1] button on your telephone

• send an Auxiliary message by pressing and holding for 2 seconds the [2] button

on your telephone

• send a Panic message by pressing and holding for 2 seconds the [3] button on

your telephone

NOTE: In the U.S.A., do not program the Aux keys for use in medical emer-

gencies as per UL requirements.

Section 5: Using Advanced Functions

This section describes how to perform more specialized functions: turning off spe-

cific detectors (bypassing zones), turning the door chime on or off, checking sys-

tem troubles, and testing your system.

Tur ning Off

Part of Your

System

(Bypassing

Zones)

Sometimes, you may need to temporarily turn off a detector:

• if you will need to go into a protected area while the system is turned on

• or, if a detector is temporarily out of service but you need to turn on the system

This is called “bypassing”. When you bypass a detector, it will not turn on the next

time you turn on your system.

Detectors (zones) cannot be bypassed once the system is on. Bypasses on detec-

tors are automatically cancelled each time the system is turned off. You must

bypass the detectors again, if required, before you turn the system on again.

NOTE: Bypassed detectors will not be able to sound an alarm - this reduces

your level of security. If a detector is not working, call a service technician

immediately so that the problem can be resolved and your system returned

to proper working order.

NOTE: For security reasons, your installer may program the system to pre-

vent you from turning off certain detectors (for example, smoke detectors).

NOTE: If you have 24-hour zones on your system, they will stay bypassed

until you turn off the bypass using the steps below (ask your installer for

more information).

1. Start with the system turned off. Press .

2. If the system asks for your [access code], enter it now.

3. Enter the two-digit number (01-32) of the detector you want to turn off

(bypass) .

The system will announce the zones (detectors) that are bypassed: “There are

(number) zones bypassed: {Zone XX}, etc...To exit, press [#].”

TIP: To find out the number of a detector, check in “System Information” on

page 30.

3. To turn a detector back on, enter the two-digit number of the zone (01-32).

The system will announce the zones (detectors) which are bypassed: “There are

(number) zones bypassed: {Zone XX}, etc...To exit, press [#].”

4. When you are finished turning off detectors, press .

5. The next time you turn on your system, the bypassed detectors will not turn

on. When you turn your system off again, the detectors will return to normal

(they will not be bypassed).

Using Advanced Functions

Checking

Trouble

Conditions

Your system continuously checks for a number of possible trouble conditions. If

one of these trouble conditions occur:

• the orange (System) light will be ON until the trouble is fixed

• the keypad will beep twice every 10 seconds until you press any key

• the NT9010 will say “System Trouble” when announcing the status of the sys-

tem

NOTE: A Trouble condition reduces the level of security your system is

designed to provide. Call your installing company for service.

To listen to an announcement of the troubles that are present, press .

To exit the trouble announcement, press .

Here is a list of the various trouble conditions that your system might announce:

Announcement: Problem and how it should be addressed:

“Service is required” If this message is announced, call for service.

“AC Power Trouble.” Electrical power to the system has been interrupted. Check your

fuse box or circuit breaker to ensure that the electricity supply

for the system is on. If this does not correct the problem, call for

service. The NT9010 may go to sleep to conserve the backup

battery if the AC power is out for more than 30 seconds. If this

happens, you can “wake up” the unit by pressing and holding

for 2 seconds.

“Phone line trouble.” Your system has detected a problem with the telephone line. If

this problem does not correct itself, or happens frequently, call

for service.

“Communication trou-

ble.”

Your system has been unsuccessful in communicating an event

to your central station. If you hear this message, call for service

immediately.

“ Zone Fault, press

[5].”

Your system has detected a fault on one or more zones (detec-

tors). Press , and the system will announce which zones have

a fault. If you are unsure of how to clear a zone fault, call for

service.

“Zone tamper, press

[6].”

Your system has detected a tamper on one or more zones

(detectors). Press and the system will announce which

zone(s) have tampers. If you are unsure how to clear the zone

tamper, call for service.

“Device low battery,

press [7].”

Your system has detected that one or more of the wireless

detectors on the system has a low battery. Press , and the sys-

tem will announce which devices have a low battery. Change

the relevant batteries. See page 25 for instructions. If this does

not correct the problem, call for service.

“The time and date

are incorrect.”

If all power to the system is interrupted (AC and battery), the

system clock and date will need to be reset. See “Setting the

Time and Date” on page 21. If you are unsure of the cause of

the system power failure, call for service.

Te s t in g Yo u r

System

Test your system every week. Report any problems immediately to your installation

company.

NOTE: Perform system tests during off-peak hours, such as early morning

or late evening.

1. If your system has remote monitoring, call the central station to tell them that

you are testing your system.

2. Begin with the system turned off. Press [Master Code] . The system

sounds the siren and turns on all keypad lights for two seconds. When the

sounder and keypad test is complete, press .

3. To test each area of your system, open each door and window in turn, or walk

in motion detector areas.

4. Press and hold the Status button for two seconds. The system will announce all

open zones.

5. If the system has any fire zones, activation will cause the alarm to sound in a

pulsed mode. To silence the alarm, press .

CAUTION: Do not use an open flame or burning materials to test a smoke

or heat detector. Contact your installer for information on safe methods of

testing detectors.

6. When you are finished testing the system, inform your central station. If the

system did not work properly, contact your installer.

NOTE: Some features described above will not be functional unless

enabled by your installer. Ask your installer which features are functional

on your system.

Allowing

Computer

Access to Your

System

From time to time, your installer may need to send information to, or retrieve

information from your security system. Your installer will do this by having a com-

puter call your system over the telephone line. You may need to prepare your sys-

tem to receive this “downloading” call. To do this:

1. Press [Master code] . This allows downloading for a limited period of

time. During this time, the system will answer incoming downloading calls.

For more information on this feature, please ask your installer.

Section 6: Customizing Your System

This section describes how to customize your system to your needs. Refer to this

section for detailed instructions on: programming access codes, setting the time

and date, and adjusting the keypad sounders and lights.

Programming

Access Codes

The master code (code 40) can be used to program system options, arm and dis-

arm the system and program other access codes. You can program up to 32 addi-

tional access codes (01 through 32). Other access codes, such as system

supervisory and duress codes, are available. Contact your installer for more infor-

mation.

1. Press [Master Code]. The red (Armed) light turns on and the orange (Sys-

tem) light flashes.

2. Enter the two-digit number of the access code you want to program (01-32 for

access codes, 40 for master code). If an access code already exists for the code

number you have selected, it will be replaced by the new code.

3. Enter the new [code]. Access codes must be four digits unless otherwise indi-

cated by your installer. Enter digits 0 through 9 only. NOTE: Do not use the fac-

tory default or obvious codes such as [1111] or [1234].

4. To exit access code programming, press .

5. Record your new codes on the “System Information” page in this booklet.

Erasing a code:

1. Press [Master Code]

2. Enter the number of the code you want to erase [01 to 32]. The Master code

cannot be erased.

3. To erase the code, press .

4. To exit access code programming, press .

Setting the

Time and Date

You should make sure that your system has the correct time and date. This is

important for the auto-arm feature to function correctly, and for accurate report-

ing of events.

1. Press [Master Code] .

2. The system announces the current time and date. To change the time, press

, then enter the Time in Hours and Minutes using the 24-Hour format

(00:00 to 23:59).

3. To change the date, press , then enter the Date in Months, Days and Years

(MM DD YY).

4. To exit programming, press .

Tur ning the

Door Chime

On or Off

If your installer has enabled the door chime feature, your NT9010 will beep when-

ever designated doors or windows are opened or closed. The NT9010 may also

announce the zones that were opened or closed, if programmed. Your installer

has programmed which doors and windows will activate the door chime.

1. Press to turn the door chime feature ON

The keypad will beep 3 times.

2. Press again to turn the door chime feature OFF

The keypad will sound one long beep.

Changing

NT9010

Speaker

Loudness

You can select from 3 different volume levels for NT9010 announcements - high,

medium and low.

1. Press and hold the Volume function key for 2 seconds. The NT9010 announces

the current volume level.

2. To change the volume level, press and hold the Volume function key again.

The NT9010 announces the next volume level option.

3. Repeat step 2 until you find a volume setting you like.

Changing

Telephone

Prompt

Loudness

If you will be using a telephone to access your system, you can change the volume

of the telephone prompts. You can select from three different telephone volume

levels.

1. Press [Master Code] . The NT9010 announces the telephone volume

level: “ Phone volume is low. To change volume, press [1]. To exit, press '#'.”

2. To change the volume, press .

3. When you have selected the volume level you want, press to exit.

Section 7: Fire Safety

Read this section carefully for important information about fire safety.

Household

Fire Safety

Audit

Most fires occur in the home. To minimize this danger, we recommend that a

household fire safety audit is conducted and a fire escape plan is developed.

1. Are all electrical appliances and outlets in a safe condition? Check for frayed

cords, overloaded lighting circuits, etc. If you are uncertain about the condition

of your electrical appliances or household service, have a professional evaluate

these units.

2. Are all flammable liquids stored safely in closed containers in a well-ventilated

cool area? Cleaning with flammable liquids should be avoided.

3. Are fire hazardous materials (matches) well out of reach of children?

4. Are furnaces and wood burning appliances properly installed, clean and in

good working order? Have a professional evaluate these appliances.

Fire Escape

Planning

There is often very little time between the detection of a fire and the time it

becomes deadly. It is thus very important that a family escape plan be developed

and rehearsed.

1. Every family member should participate in developing the escape plan.

2. Study the possible escape routes from each location within the house. Since

many fires occur at night, special attention should be given to the escape

routes from sleeping quarters.

3. Escape from a bedroom must be possible without opening the interior door.

Consider the following when making your escape plans:

• Make sure that all border doors and windows are easily opened. Ensure that

they are not painted shut, and that their locking mechanisms operate smoothly.

• If opening or using the exit is too difficult for children, the elderly or handi-

capped, plans for rescue should be developed. This includes making sure that

those who are to perform the rescue can promptly hear the fire warning signal.

• If the exit is above the ground level, an approved fire ladder or rope should be

provided as well as training in its use.

• Exits on the ground level should be kept clear. Be sure to remove snow from

exterior patio doors in winter; outdoor furniture or equipment should not block

exits.

• Each person should know of a predetermined assembly point where everyone

can be accounted for i.e.: across the street or at a neighbor’s house. Once

everyone is out of the building, call the Fire Department.

• A good plan emphasizes quick escape. Do not investigate or attempt to fight

the fire, and do not gather belongings or pets as this wastes valuable time.

Once outside, do not re-enter the house. Wait for the fire department.

• Write the fire escape plan down and rehearse it frequently so that should an

emergency arise, everyone will know what to do. Revise the plan as conditions

change, such as the number of people in the home, or if there are changes to

the building’s construction.

• Make sure your fire warning system is operational by conducting weekly tests

(see “Here is a list of the various trouble conditions that your system might

announce:” on page 19). If you are unsure about system operation, contact

your installing dealer.

• We recommend that you contact your local fire department and request further

information on fire safety and escape planning. If available, have your local fire

prevention officer conduct an in-house fire safety inspection.

Section 8: Replacing Batteries

From time to time, the batteries in the detectors and other components on your

system will need to be changed. If a device has a low battery, your system will

announce a “Device Low Battery” trouble (see “Checking Trouble Conditions” on

page 19).

When batteries in one device need to be replaced, it is suggested that the batter-

ies in all devices be replaced at the same time. All of the batteries used in the secu-

rity system are Eveready Alkaline Energizer batteries.

NOTE: Before changing batteries in the detectors, you should inform your

central station.

Tips for

Buying

Batteries

• Your system is designed to work with Eveready Alkaline Energizer Batteries.

When replacing batteries, be sure to buy the same brand and type of batteries.

Do not replace the batteries on your system with any other type. The reliability

of your security system depends on its batteries, and “no name” or generic

brand batteries may not provide the best quality and dependability.

• Use fresh batteries. Most batteries have a “best before” date printed on their

packaging or on the batteries themselves. Buy batteries that have a “best

before” date of two years or more from your purchase date.

• When disposing of used batteries, follow the instructions and precautions

printed on the batteries. Many cities and communities have collection sites or

services for used household batteries. Contact your municipal offices for infor-

mation on the disposal of used batteries.

• If in doubt about the batteries used in your system, or if you have trouble

installing them, contact your installer for assistance.

Required Eveready Alkaline Energizer Batteries

WLS904 Motion Detector: Four ‘AAA’ batteries.

WLS906 Wireless Smoke Detector: Six ‘AA’ batteries.

WLS907 Universal Transmitter: Three ‘AAA’ batteries.

WLS908 Wireless Panic Pendant: battery cannot be changed - replace the unit.

WLS909 Wireless Key: Three Photo/Electronic 1.5V batteries.

WLS910 Wireless Handheld Keypad: Three ‘AAA’ batteries.

WLS912 Wireless Glassbreak Detector: Three ‘AA’ batteries.

WLS914 Pet Immune Motion Detector: Four ‘AAA’ batteries.

WLS915 Universal Transmitter: One Lithium Energizer No. EL123AP battery.

Door/Window

Contacts

WLS907

Insert a small screwdriver into the slot on the side of the detector. Push the screw-

driver in and lift off the cover.

Remove the old batteries and install three fresh Eveready Alkaline Energizer AAA

batteries. Be sure to insert the batteries in the proper orientation. Carefully

replace the cover.

WLS915

To remove the cover of the universal trans-

mitter, squeeze both sides of the unit where

the notches are. Pull to release the cover.

Use care when installing the battery and

observe the correct polarity (see diagram).

Use only a Eveready Lithium Energizer No.

EL123AP battery.

Motion

Detectors

Remove the motion detector from its mounting plate by

holding the detector by its sides and pushing up.

Remove the old batteries and install four fresh Eveready

Alkaline Energizer AAA batteries. Be sure to insert the

batteries in the proper orientation. Replace the detector

on its mounting plate, making sure it snaps into place.

Handheld

Keypad

The WLS910 requires three “AAA” batteries. To replace the batteries, remove the

plastic battery cover from the back of the unit. Remove all of the old batteries.

Insert the new batteries and replace the plastic battery cover.

Replacing Batteries

Glassbreak

Detector

Remove the detector from its mounting plate:

press the detector in the direction shown at

right.

Install the batteries negative (–) side first, with

the correct polarity, as shown at right.

Smoke

Detectors

The WLS906 requires six Eveready Energizer AA batter-

ies. To replace the batteries, remove the detector from

the mounting plate by pushing the locking tab and

turning the detector counter-clockwise.

Hold the unit with the battery compartment facing

you, and the imprinted wording right-side up. Install

the first two batteries in the row nearest to you, with

the + terminals facing left. Next, install the middle two

batteries with the + terminals facing to the right. Place

your thumb over the centre of these four batteries to

keep them in place. Install the last two batteries, with

their + terminals facing to the left, by snapping them past the nylon retainer.

Wireless Keys The WLS909 requires three LR44 batteries. To replace the bat-

teries, remove the screw on the back of the key and carefully

separate the two sides of the key’s plastic casing. Remove the

old batteries from between the two metal clips. Insert the new

batteries according to the diagram at right and reattach the

two sides of the key’s plastic casing. The polarity of the batter-

ies must be observed.

Panic

Pendants

You cannot change the batteries on a WLS908 Panic Pendant. Call your installer

and have the unit replaced.

After

Installing

New Batteries

After you change the batteries on your system, the system may announce trouble

conditions. A zone tamper should be displayed for each detector that had its bat-

teries changed. A zone fault may also be displayed for these detectors. Refer to

“Checking Trouble Conditions” on page 19 for information on checking Zone

Faults and Zone Tampers.

Be sure to perform a complete test of your system after new batteries are installed

to ensure that all detectors are working properly (see “Testing Your System” on

page 20).

Section 9: Glossary

Access code A 4- or 6-digit code that you enter on the keypad to turn your system on or off, or

to use other system features.

Alarm When a zone is violated (e.g. a smoke detector detects smoke, a motion detector

senses movement, a door with a contact is opened), it will trigger an alarm.

Intrusion (burglary) alarm: An alarm triggered by an intrusion detector (e.g.

motion detectors, glassbreak detectors, door/window contacts). Usually occurs

when the system is on. Intrusion alarms sound with a steady siren.

Fire alarm: An alarm triggered by fire, smoke or heat detectors. Fire alarms may

be triggered at any time, whether the system is on or off. Fire alarms sound with a

pulsing siren.

Audible exit

fault

A feature that warns you of an improper exit (e.g. door not completely shut) when

you attempt to turn on your system. Helps to prevent false alarms.

Away arming Turning on the system so that all the detectors (perimeter and interior) are on. (Use

when everyone is away from the premises.)

Bypassing a

zone

Turning off a detector temporarily. When you bypass a zone, the detector for that

zone will not monitor activity in the zone and will not be able to trigger an alarm.

Central

station

If remote monitoring is enabled, your system will send alarms, troubles and emer-

gency messages to the central station. The central station will then notify authori-

ties in your area, if necessary.

Detector A part of the system that can detect and report problems (e.g. a motion detector

can tell if there is movement in a room).

Emergency

message

A message sent to the central station when one of the pairs of emergency keys

( ) is pressed and held for two seconds. Your installer must program these

keys, or they will not work.

Entry time A timer programmed by your installer. It starts when you enter an area of the sys-

tem that is on. You must enter an access code to turn the system off before the

timer runs out, or else an alarm will be triggered.

Glossary

Entry/exit

doors

Your installer will set the doors you usually use to enter or exit the premises as

entry/exit doors. These doors are programmed to have entry and exit times so that

you can turn the system on and off without causing a false alarm.

Exit time A timer programmed by your installer. It starts when you turn on your system to

allow you a period of time to leave the premises. At the end of the exit time, the

system will be on.

Local

telephone

If your NT9010 system is connected to your premise telephone line, you may be

able to use a telephone located on the premise to access the system.

Master code The master code is a 4- or 6- digit access code that is used to set system options,

to turn the system on and off, and to program other access codes.

Remote

telephone

If your NT9010 system is connected to an incoming telephone line, you may be

able to use an off-premise (remote) telephone to access the system.

Stay mode Turning on the system so that only the perimeter zones are on. (Use when one or

more people will stay on the premises.)

Trouble The NT9010 control unit continuously checks the system for problems. If the con-

trol unit finds a problem (trouble), it will indicate this at the keypad. See “Checking

Trouble Conditions” on page 19 for a list of possible trouble conditions.

Zone A limited area of the premises monitored by a detector (smoke detector, door/win-

dow contact, motion detector, glassbreak detector, etc.).

Perimeter zone: A zone that detects intrusion from outside the premises (e.g.

door contact on an outside door, glassbreak detector).

Interior zone: A zone that detects intruders that have already entered (e.g.

motion detector).

Fire zone: A heat or smoke detector.

System Information

Fill out the following information for future reference and store this guide in a safe place.

For Service

Central Station Information:

Account #: ______________________________ Telephone #: ____________________________

Installer Information:

Company: _______________________________ Telephone #: ____________________________

Access Codes

Your Master Code is: ____________________________

Additional Access Codes:

System Information

[F] FIRE _____________________________________

[A] AUXILIARY ______________________________

[P] PANIC ___________________________________

The Exit Time is_______________________seconds.

The Entry Time is _____________________seconds.

Code # Access Code Code # Access Code Code # Access Code Code # Access Code

01 09 17 25

02 10 18 26

03 11 19 27

04 12 20 28

05 13 21 29

06 14 22 30

07 15 23 31

08 16 24 32

System Information

Zone Information

There are ________ active zones on the system.

Zone Protected Area Zone Type Zone Protected Area Zone Type

01 17

02 18

03 19

04 20

05 21

06 22

07 23

08 24

09 25

10 26

11 27

12 28

13 29

14 30

15 31

16 32

Index

AC power trouble message

Access codes

adding 21

changing 21

defined 28

erasing 21

Master code 29

programming 21

telephone code 7

Alarm

checking 16

defined 28

false 15

fire 15

intrusion 16

memory 16

Answering the telephone 8

Armed light 3

turning off system 10

turning on system 9

Arming

automatic 13

away 11

basic 9

no entry delay 13

quick 12

stay 12

Automatic arming 13

Auxiliary keys 17

Away 11

Batteries 25–27

Burglary alarm 16

Buttons

see Function buttons

Bypassing zones 18

Central station 6

defined 28

talk/listen-in feature 16

Checking

alarms 16

troubles 19

Chime 22

Cleaning the system 6

Codes See Access codes

Communication trouble

message 19

Computer access to system

Date

setting 21

Detectors

defined 28

Tyco Safety Canada 00NB9001 Receiver User Manual Users guide

Digital Security Controls Ltd. Receiver Users guide

Contents

Users guide

Navigation menu

Namespaces

Views

Navigation