Tyco Safety Sensormatic BIX1000 Business Intelligence Module User Manual REV
Tyco Safety Products/Sensormatic Business Intelligence Module REV
Contents
- 1. User manual
- 2. User manual_REV
User manual_REV
PRELIMINARY Wireless Device Module (BIX1000) Installation Guide BIX1000 © 2018 Sensormatic Electronics, LLC WIRELESS DEVICE MODULE (BIX1000) INSTALLATION GUIDE 8200-1088-15, REV 3D 1 of 16 *8200-1088-15* PRELIMINARY Contents About this guide .................................................................................................................................................. 3 Additional documentation .............................................................................................................................. 3 Technical Support ......................................................................................................................................... 3 Training ......................................................................................................................................................... 3 About the product ............................................................................................................................................... 4 Features ........................................................................................................................................................ 4 Compatibility .................................................................................................................................................. 5 Cable kit numbers ......................................................................................................................................... 5 Tool requirements ......................................................................................................................................... 6 Section I: Before you begin ................................................................................................................................ 6 System requirements ....................................................................................................................................... 6 Firmware requirements ................................................................................................................................. 6 Laptop requirements ..................................................................................................................................... 6 Wiring requirements ...................................................................................................................................... 6 Safety ................................................................................................................................................................. 7 Installation prerequisites ................................................................................................................................. 7 Section II: Installation sequence overview ......................................................................................................... 8 Section III: Installing the BIX1000 ...................................................................................................................... 9 Overview of steps............................................................................................................................................. 9 Step 1: Connecting the BIX1000 cable to the EAS device ........................................................................... 9 Step 2: Commissioning the BIX1000 .............................................................................................................. 9 Step 3: Locating the BIX1000 ........................................................................................................................ 11 Specifications ................................................................................................................................................... 14 Declarations ..................................................................................................................................................... 15 Other declarations .......................................................................................................................................... 16 WIRELESS DEVICE MODULE (BIX1000) INSTALLATION GUIDE 8200-1088-15, REV 3D 2 of 16 *8200-1088-15* PRELIMINARY About this guide This installation guide explains how to install the Wireless Device Module (BIX1000), with the Wireless Device Manager (BIM1000), to synchronize and aggregate data from all Sensormatic-connected devices. Additional documentation The following is a list of additional documents related to this installation: • Wireless Device Manager (BIM1000) Installation Guide, 8200-1088-03. • Wireless Device Manager (BIM1000) and Wireless Device Module (BIX1000) Setup Guide, 8200-1088-01. • Ultra Post® IV AMS-1012 Wireless Device Module (BIX1000) Cable Kit Installation Guide, 8200-1088-05. • Ultra Post® VI AMS-1014 Wireless Device Module (BIX1000) Cable Kit Installation Guide, 8200-1088-06. • Ultra 1.8 Meter ABS Pedestal Wireless Device Module (BIX1000) Cable Kit Installation Guide, 8200-1088-07. • AMB9010-IPS and AMB-1200 Label Deactivator Controller Wireless Device Module (BIX1000) Cable Kit Installation Guide, 8200-1088-08. • AMS-9050 Controller Wireless Device Module (BIX1000) Cable Kit Installation Guide, 8200-1088-09. • AMS-9040 Controller Wireless Device Module (BIX1000) Cable Kit Installation Guide, 8200-1088-10. • AMS-9060 Controller and AMS-1170-2C/4C Controller Wireless Device Module (BIX1000) Cable Kit Installation Guide, 8200-1088-11. • ZBSMPROE ScanMax® Pro Label Deactivator Controller Wireless Device Module (BIX1000) Cable Kit Installation Guide, 8200-1088-12. • IDKM-10XX/AMK-10XX SuperTag® Detacher Wireless Device Module (BIX1000) Cable Kit Installation Guide, 8200-1088-13. • AMB-2011/AMB-1101/ZBAMB9010 EAS Label Deactivator Wireless Device Module (BIX1000) Cable Kit Installation Guide, 8200-1088-16. • Wireless Device Module (BIX1000) Extension Cable Kit Installation Guide, 8200-1088-14. • AMS-1080 Controller Wireless Device Module (BIX1000) Cable Kit Installation Guide, 8200-1088-17. Technical Support For product bulletins, and the most recent updates to this guide, visit https://sensormaticsecurelogin.com Training WARNING: Do not install a Wireless Device Module (BIX1000) unless you have completed the following Wireless Device Manager (BIM/BIX) Training Curriculum modules: • BIM and BIX Installation Technical Training. • BIM Configuration Technical Training. • Optional: SMaaS Overview Sales Training. WIRELESS DEVICE MODULE (BIX1000) INSTALLATION GUIDE 8200-1088-15, REV 3D 3 of 16 *8200-1088-15* PRELIMINARY About the product The Wireless Device Manager (BIM1000) is a wireless access point that uses an IEEE 802.15.4 wireless standard to connect to the Wireless Device Module (BIX1000). The Wireless Device Module (BIX1000), as shown in Figure 1, uses the IEEE 802.15.4 wireless protocol to connect to the Wireless Device Manager (BIM1000) to synchronize all in-store Sensormatic-connected deactivation and detection controllers, to collect data and to provide a health status for all the connected devices. The synchronization between the deactivation and the detection controllers minimizes failed deactivation at the Point-of-Sale (POS) and nuisance alarms at the store exit area. The data collected includes alarms, events, and people-counting statistics. It also collects alarm input responses through an Android tablet device. Customers can use a desktop browser to log into a TrueVUE reporting platform, or a Shrink Management as a Service (SMaaS) platform, to access historical daily data reports from all the connected devices. The customer can also use an Android tablet device for alarm input responses. Important: You must install the Wireless Device Manager (BIM1000) before you install the Wireless Device Module (BIX1000). Features The Wireless Device Module (BIX1000) has the following features: • It is auto-discovered by the BIM1000 after commissioning. • It uses the wireless IEEE 802.15.4 Standard for communications. • It has external LED status and signal strength indicators. • It has Micro USB Type B access for commissioning. Figure 1. BIX1000 RS-485 port Status LED indicator WIRELESS DEVICE MODULE (BIX1000) INSTALLATION GUIDE Signal strength LED indicators Micro USB port 8200-1088-15, REV 3D 4 of 16 *8200-1088-15* PRELIMINARY Compatibility The Wireless Device Module (BIX1000) is compatible with the following devices: • The Ultra Post® IV AMS-1012 Pedestal. • The Ultra Post® VI AMS-1014 Pedestal. • The Ultra 1.8 Meter ABS Pedestal. • The AMS-9060 Controller. • The AMS-9050 Controller. • The AMS-9040 Controller. • The AMS-1080 Controller. • The AMS-1170-2C/4C Controller. • The ZBAMB9010 EAS Label Deactivator Controller. • The AMB9010-IPS EAS Label Deactivator Controller. • The ZBSMPROE ScanMax® Pro Label Deactivator Controller. • The AMB-1200C EAS Label Deactivator Controller. • The AMK-1000 and the AMK-1010 SuperTag® Detacher. • The IDKM-1000 and the IDKM-1010 SuperTag® Detacher. • The AMB-2011 Value Pad II Countertop EAS Label Deactivator. • The AMB-1101 VersaPass II Countertop EAS Label Deactivator. Cable kit numbers Table 1 lists the cable kit numbers for the EAS devices that are compatible to install with a Wireless Device Module (BIX1000). Table 1. BIX1000 cable kit numbers, cable part numbers, and installation guide numbers Description Ultra Post® IV AMS-1012 Pedestal The Ultra Post® VI AMS-1014 Pedestal Ultra 1.8 Meter ABS Pedestal AMB9010-IPS and AMB-1200 EAS Label Deactivator Controller AMS-9060 Controller and AMS-1170-2C/4C Controller AMS-9050 Controller AMS-9040 Controller ZBSMPROE ScanMax® Pro Label Deactivator Controller IDKN-10XX/AMK-10XX SuperTag® Detacher Wireless Device Module BIX1000 Extension Cable Kit AMB-2011 Value Pad II Countertop EAS Label Deactivator, AMB-1101 VersaPass II Countertop EAS Label Deactivator, and ZBAMB9010 EAS Label Deactivator Controller AMS-1080 Controller Cable kit number 0352-0710-01 0352-0711-01 0352-0757-01 0352-0696-01 Cable part number 0652-0890-01 0652-0891-01 0652-0893-01 0652-0889-01 Installation guide 8200-1088-05 8200-1088-06 8200-1088-07 8200-1088-08 0352-0695-01 0352-0694-01 0352-0693-01 0352-0760-01 0652-0888-01 0652-0887-01 0652-0886-01 0652-0845-01 8200-1088-11 8200-1088-09 8200-1088-10 8200-1088-12 0352-0697-01 0352-0765-01 0352-0780-01 0652-0892-01 0652-0894-01 0652-0898-01 8200-1088-13 8200-1088-14 8200-1088-16 0352-0789-01 0652-0901-01 8200-1088-17 WIRELESS DEVICE MODULE (BIX1000) INSTALLATION GUIDE 8200-1088-15, REV 3D 5 of 16 *8200-1088-15* PRELIMINARY Tool requirements You require the following tools to install the Wireless Device Module (BIX1000): • A #2 Phillips head screwdriver. • A small slotted screwdriver. • A drill with a 3/32 inch (2.38 millimeter) drill bit. • A micro USB cable, 6003-0313-01, to connect to the BIX1000. Section I: Before you begin Before you install the Wireless Device Module (BIX1000), ensure that you adhere to the criteria in the following sections. System requirements This section outlines the system requirements that you need to install a BIX1000. Firmware requirements To support the installation of the BIX1000, download the BIX Firmware Tool from https://sensormaticsecurelogin.com/. To download the BIX Firmware Tool, complete the following steps: 1. Open a web browser and launch https://sensormaticsecurelogin.com/. 2. Enter your valid log on information, and click Login. 3. From the Tech Support menu, click EAS. 4. Click Software Download. 5. Click BIX Firmware Tool. 6. To download the software bundle, click the link, and save the file to a local folder on your laptop. 7. Log out of www.sensormaticsecurelogin.com/. 8. On your laptop, rename the file that you saved to an .exe file. Click the executable file, and click Run. 9. Follow the setup wizard instructions to save the software on your laptop. Note: Files save to the following location: C:\Program Files\Sensormatic\BIX Software Bundle (Program Files (x86) for 64 bit machines). Laptop requirements Your laptop must have a USB port to connect to the Wireless Device Module (BIX1000). Wiring requirements For information on wiring requirements, see Table 1. WIRELESS DEVICE MODULE (BIX1000) INSTALLATION GUIDE 8200-1088-15, REV 3D 6 of 16 *8200-1088-15* PRELIMINARY Safety You must adhere to the following safety instructions when you install a Wireless Device Module (BIX1000): WARNING: Risk of electric shock Disconnect all power sources before servicing. • You must use plenum-rated cables, unless the cables are in raceways. • Installation of the BIX1000 must comply with the latest national electrical codes, national fire code, and all applicable local codes and ordinances. National or local wiring codes may differ between regions. Adherence to these codes supersedes instructions in this document. • You must observe and respect all the safety instructions in this installation guide, and the operation of the BIX1000. • You must mount the BIX1000 only as instructed in this installation guide. Mounting the BIX1000 any other way can affect its operation. • The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications can void the user’s authority to operate the equipment. • You must install the antennas for this transmitter with a separation distance of at least 20 centimetres (8 inches) from all persons, and must not be co-located or operating in conjunction with any other antenna or transmitter. Installation prerequisites To install the BIX1000, you must have the following criteria in place before you proceed: • Have you completed the training required to commission the BIM1000 and BIX1000? • Did you download the supporting firmware version for the BIX Firmware Tool? • Did you download the supporting firmware version for the EAS devices that you are connecting to each BIX1000? • Is the BIM1000 installed? • Is the BIM1000 turned on, and programmed with the Personal Area Network (PAN) ID and the Channel? For information on configuring the radio settings, refer to the Commissioning the Wireless Device Manager section in the Wireless Device Manager (BIM1000) and Wireless Device Module (BIX1000) Setup Guide, 8200-1088-01. WIRELESS DEVICE MODULE (BIX1000) INSTALLATION GUIDE 8200-1088-15, REV 3D 7 of 16 *8200-1088-15* PRELIMINARY Section II: Installation sequence overview Figure 2 gives an overview of the complete installation sequence you must follow when you install a BIM1000 and a BIX1000. You must install the BIM1000 before you install the BIX1000. Figure 2. BIM1000 and BIX1000 complete installation sequence Before you begin: Planning and prerequisites Step 1: Install the BIM1000 Confirm all the prerequisites in Section I are complete before beginning Install the BIM1000. Turn on the BIM1000, and program the PAN ID and the Ch Step 5: Validate BIM1000 configuration Step 6: Validate BIM1000 remote connectivity Validate the complete BIM1000 and BIX1000 configuration Validate the remote connectivity and data transportation of the Step 2: Install the BIX1000 cable kits Install the relevant BIX1000 cable kit, and configure the EAS d i Step 3: Commission the BIX1000 Step 4: Install and locate the BIX1000 Commission the BIX1000 Install and locate the BIX1000 Important: This installation guide only describes the following steps in the complete BIM1000 and BIX1000 installation sequence: • Before you begin: Planning and prerequisites • Step 3: Commission the BIX1000 • Step 4: Install and locate the BIX1000 WIRELESS DEVICE MODULE (BIX1000) INSTALLATION GUIDE 8200-1088-15, REV 3d 8 of 16 *8200-1088-15* PRELIMINARY Section III: Installing the BIX1000 This section outlines how to install a Wireless Device Module (BIX1000). Important: You must install the Wireless Device Manager (BIM1000) before you install the Wireless Device Module (BIX1000) to verify that the signal strength is sufficient in the selected mounting location. Overview of steps This section gives an overview of the steps to install a BIX1000: • Step 1: Connecting the BIX1000 cable to the EAS device • Step 2: Commissioning the BIX1000 • Step 3: Locating the BIX1000 Step 1: Connecting the BIX1000 cable to the EAS device You must connect the BIX1000 to compatible EAS devices using the appropriate cable kit. The RJ45 end of each cable kit is labelled to indicate which end of the cable connects to the RS-485 port on the BIX1000. For the location of the RS-485 port on the BIX1000, see item A in Figure 1. To connect the BIX1000 to a compatible EAS device, complete the following step: • Select the EAS device you are installing from Table 1, and connect the EAS device to the BIX1000, as described in the relevant installation guide. Note: When you connect the EAS device to the BIX1000, the Status LED on the BIX1000 should change to solid green within 20 seconds. For information on the BIX1000 status LEDs, see Table 4. Step 2: Commissioning the BIX1000 Before you secure the BIX1000, you must commission it in order to test different mounting locations and to verify signal strength. Note: For more information on how to commission the BIX1000, refer to the Wireless Device Manager (BIM1000) and Wireless Device Module (BIX1000) Setup Guide, 8200-1088-01. To commission the Wireless Device Module (BIX1000), complete the following steps: 1. If installing the BIX1000EA module, locate the SMA antenna, 3411-0024-01, from the BIX1000 installation kit, and screw the SMA antenna into the SMA connection port on the BIX1000EA. Figure 3. SMA antenna to SMA connector on the BIX1000EA SMA antenna, 3411-0024-01 BIX1000EA module WIRELESS DEVICE MODULE (BIX1000) INSTALLATION GUIDE SMA connection port 8200-1088-15, REV 3a 9 of 16 *8200-1088-15* PRELIMINARY 2. Connect the micro USB cable, 6003-0313-01, to the BIX1000 micro USB port. For the location of the USB port, see item D in Figure 1, on page 4. Connect the opposite end of the micro USB cable to the USB port on your laptop. Note: The laptop powers the BIX1000 through the USB port. 3. Wait 15 seconds for the BIX1000 boot sequence to complete. 4. When the BIX1000 boot sequence completes, launch the BIX Firmware Tool you downloaded preinstallation. 5. Update the firmware on the BIX1000 by completing the following steps: a. In the Controller Download pane, click Browse, and then select the supporting firmware version for the BIX1000. b. Click Start Flash Download. Note: If an error occurs during the download, you must close the BIX Firmware Tool, disconnect the device, and then repeat steps 2 to 6. 6. After the flash download, complete the following steps to establish communication between the BIM1000 and the BIX1000: Important: In the following steps, ensure you save the changes to each individual parameter before you change the next parameter. a. Open the BIM Web Launch Tool, and from the BIM Configuration menu, click Radio Settings. Record the values in the PAN ID and Channel fields, and then close the BIM Web Launch Tool. b. Return to the BIX Firmware Tool window. c. In the PAN ID field enter the PAN ID value you recorded for the BIM1000, and click the Antenna icon to save the changes. For the location of the save button, see Figure 4. Note: The PAN ID is limited to the hex characters A-F and 0-9. The PAN ID you set for the BIX1000 must match the PAN ID set for the BIM1000 to establish communication between the two devices. d. In the Channel field, enter the Channel value you recorded from the BIM1000, and click the Antenna icon to save the changes. Note: You can set a value from 11 to 26 for IEEE 802.15.4 radio frequencies. Regulatory restriction: Do not use channel 25 or channel 26 in North America. e. In the Tx Power field, enter the Tx power value for the country of use, as shown in Table 2. Click the Antenna icon to save the changes. Table 2. BIM1000 and BIX1000 TX power Device BIM1000 BIX1000 BIX1000EA TX power, North America 197 (20dB) 197 (20dB) 220 (20dB) TX power, Europe 70 (10dB) 94 (10dB) 85 (10dB) 7. Optional: In the Location field, enter a description of the location of the BIX1000, for example, East Entrance. Click the Antenna icon to save the changes. Note: Entering a location description helps to locate devices after installation. WIRELESS DEVICE MODULE (BIX1000) INSTALLATION GUIDE 8200-1088-15, REV 3a 10 of 16 *8200-1088-15* PRELIMINARY Figure 4. BIX Firmware Tool window Antenna icons, click to save parameters 8. With the BIX1000 connected to your laptop, temporarily place the BIX1000 in the area where you are installing it to validate the signal strength. For information on the BIX1000 signal strength indicators, see Step 3: Locating the BIX1000. Note: When validating the signal strength, ensure you are within the coverage range of the BIM1000. 9. Close the BIX Firmware Tool. Important: You must close the BIX Firmware Tool before you disconnect the micro USB cable from the BIX1000. If you do not close the BIX Firmware Tool first, the drivers for the BIX1000 can lock and the app may not connect to the BIX1000. If this occurs, you must restart your laptop to resolve the issue. 10. Disconnect the micro USB cable, 6003-0313-01, from the BIX1000. Step 3: Locating the BIX1000 Adhere to the following guidelines when determining the installation location of the BIX1000: • Do not directly hold the BIX1000 module because your body and hand can detune the antenna. • The BIX1000 can be orientation sensitive at the periphery of its range to the BIM1000. • The wireless communication between the BIM1000 and the BIX1000 solution is most effective when the modules are within a direct line of sight. Avoid placing the BIX1000 modules in metal enclosures or deep underneath counters. Placing the BIX1000 on a higher mounting location can extend its signal strength. Important: If you connect the BIX1000 to an AMS-9060 controller, an AMS-9050 controller, or an AMS-9040 controller, do not secure the BIX1000 to the case of the controller. To locate the BIX1000 correctly, complete the following steps: 1. After you connect the BIX1000 to the EAS device using the appropriate cable installation kit, determine the location of the BIX1000. Notes: • You must place the BIX1000 a minimum of 2 feet (24 inches) from the BIM1000. WIRELESS DEVICE MODULE (BIX1000) INSTALLATION GUIDE 8200-1088-15, REV 3a 11 of 16 *8200-1088-15* PRELIMINARY • Table 3 lists the expected maximum line of sight range from the BIM1000 module to the BIX1000 module for each region. The maximum line of sight ranges are based on environments free of obstructions and interference. The range can significantly degrade from the specified maximums. Table 3. Expected maximum line of sight ranges from the BIM1000 to the BIX1000 Modules Region Expected maximum line of sight range BIM1000 to BIX1000 BIM1000 to BIX1000EA BIM1000 to BIX1000 EU EU US 76.2 meters (250 feet) 106.7 meters (350 feet) 106.7 meters (350 feet) 2. Optional: If you need to locate the BIX1000 further away from the EAS device for improved signal reception or for mounting purposes, install the BIX1000 Extension Cable Kit, 0352-0765-01, as described in the Wireless Device Module (BIX1000) Extension Cable Kit Installation Guide, 8200-1088-14. Note: Use the BIX1000 Cable Extension Kit to relocate the BIX1000 module up to 3.3 meters (10 feet) away from the EAS device to which you are connecting the BIX1000. 3. Ensure that the status LED on the BIX1000 is green. For information on the status LED descriptions, see Table 4. Table 4. BIX1000 status LED description BIX1000 status LED color BIX1000 status description No status LED displaying Status LED displaying green Status LED flashing amber quickly Status LED flashing amber slowly Status LED flashing red Powered off or in Boot Loader Mode Operating correctly Attempting communication with an EAS device The Phase Lock Loop (PLL) is unlocked, and indicates a synchronization error There is no communication between the BIX1000 and the BIM1000 4. To ensure strong signal strength, select one of the following options: • Ensure the signal strength LEDs on the BIX1000 display at least one green LED. If it does not, move the BIX1000 until it displays one or more green LEDs. For information on the signal strength indicators on the BIX1000, see Table 5. • Connect the BIX1000 to your laptop and wait for the BIX1000 boot sequence to complete as described in steps 2 to 5 on page 9, and then use the BIX Firmware Tool to determine the Received Signal Strength Indicators (RSSI) value. Table 5. BIX1000 signal strength LED description BIX1000 signal strength LED color RX signal strength description No green signal strength LEDs displaying One green signal strength LED displaying Two green signal strength LEDs displaying Three green signal strength LEDS displaying Signal strength is below -85 decibels Signal strength is -85 to -75 decibels Signal strength is -75 to -60 decibels Signal strength is above -60 decibels 5. When you identify an ideal mounting location, locate the alcohol pads, 1600-0033, from the BIX1000 Installation Kit, 0352-0733-01, and use the alcohol pads to clean the surface area of the mounting location. 6. Remove the release liner from the adhesive pad on the BIX1000, and secure it to the correct location near or on the EAS device. For more information on a specific EAS device, refer to the relevant installation guide listed in Table 1. 7. Optional: If you need to secure the BIX1000 using the screws supplied in the installation kit, complete the following steps: a. Locate the BIX1000 back cover plate, 0404-1244-01, from the BIX1000 Installation Kit, 0352-0733-01. WIRELESS DEVICE MODULE (BIX1000) INSTALLATION GUIDE 8200-1088-15, REV 3a 12 of 16 *8200-1088-15* PRELIMINARY b. Use the BIX1000 back cover plate as a template, and mark the location of the pilot holes on the mounting surface. c. Remove the BIX1000 back cover, and using a drill with a 3/32 inch or 2.38 millimeter drill bit, drill two mounting holes in the mounting surface. d. Insert the two screws, 5810-2042-120, from the installation kit into the BIX1000 back cover, and into the two mounting holes in the mounting surface. e. Ensure that the two mounting screws are recessed below the plastic surface, and secure the back cover to the mounting surface. Note: The screw holes on the BIX1000 back cover plate are symmetrical. The other features on the BIX1000 back cover plate are not symmetrical because they accommodate the micro USB and the RS-485 ports. 8. Secure the BIX1000 to its mounting surface. WIRELESS DEVICE MODULE (BIX1000) INSTALLATION GUIDE 8200-1088-15, REV 3a 13 of 16 *8200-1088-15* PRELIMINARY Specifications Electrical Power supply Primary input ......................................................................................................................................................................... ..................................................... / 5V – 24VDC input, Sync and RS485 through RJ45 8 pin header with LEDs for RS485. Environmental Operating temperature..................................................... ........................................................ 0°C to 50°C (32°F to 122°F) Relative humidity ............................................................. ............................................................ 0 to 90% non-condensing Enclosure Rating ............................................................. ..................................................................................... UL94 V-O Evaluated for altitudes less than 2,000 meters (6,561.68 feet) Mechanical Material: ........................................................................... ..............................................................................................ABS Color: .............................................................................. ..................................................................................... Light grey Dimensions: .................................................................... .................................................. 58.6 mm X 46.7 mm X 24.9 mm Weight (approx.): ............................................................ ....................................................................... 32.66 g (0.072 lbs) Dimensions Figure 5. BIX1000 dimensions 58.5 mm 47 mm 52.6 mm 58.5 mm WIRELESS DEVICE MODULE (BIX1000) INSTALLATION GUIDE 8200-1088-15, REV 3a 14 of 16 *8200-1088-15* PRELIMINARY Declarations Model: BIX1000 Regulatory information Radio Frequency of operation Type.......................................................... .............................................................................................................. BIX1000 Frequency band............................. .......................................................................................................... .2400-2483.5 MHz Maximum power ................................... ..................................................................................................... 10 mW in the EU ........................................................................................................................................................................ 100 mW in NA If frequency is selectable for your model, select only the country in which you are using the device. Any other selection will make the operation of this device illegal. Approved antennas Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. Conformément à la réglementation d’Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d’un type et d’un gain maximal (ou inférieur) approuvé pour l’émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l’intention des autres utilisateurs, il faut choisir le type d’antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l’intensité nécessaire à l’établissement d’une communication satisfaisante. This radio transmitter IC: 3506A-BIX1000 has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Le présent émetteur radio IC: 3506A-BIX1000 a été approuvé par Industrie Canada pour fonctionner avec les types d’antenne énumérés ci-dessous et ayant un gain admissible maximal et l’impédance requise pour chaque type d’antenne. Les types d’antenne non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l’exploitation de l’émetteur. Pulse/Larsen W1027 Polarization ..................................................... .......................................................................................................... Vertical Composite gain ............................................... .......................................................................................................... 3.2 dBi Impedance .................................................... ......................................................................................................... 50 ohms Pulse/Larsen W1038 Polarization ..................................................... .......................................................................................................... Vertical Composite gain ............................................... ..........................................................................................................3.8 dBi Impedance .................................................... ......................................................................................................... 50 ohms L-Com model HG2403RD-RSF Polarization ..................................................... .......................................................................................................... Vertical Composite gain ............................................... ...........................................................................................................3.0 dBi Impedance .................................................... ......................................................................................................... 50 ohms Antenova model SRCW004 Polarization ..................................................... ............................................................................................................ Linear Composite gain ............................................... .......................................................................................................... 2.5 dBi Impedance .................................................... ......................................................................................................... 50 ohms FCC ID: BVCBIX1000 WIRELESS DEVICE MODULE (BIX1000) INSTALLATION GUIDE 8200-1088-15, REV 3a 15 of 16 *8200-1088-15* PRELIMINARY This device complies with part 15 of the FCC Rules. This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. México NOM 121: BIX1000 La operación de este equipo está sujeta a las siguientes dos condiciones: 1) es posible que este equipo o dispositivo no cause interferencia perjudicial y 2) este equipo debe aceptar cualquier interferencia, incluyendo la que pueda causar su propia operación no deseada. INTERNATIONAL ID: BIX1000 EMC ....................................................... .................................................................................................... 47 CFR, Part 15 ............................................................................................................................................................................ EN 300 328 ......................................................................................................................................................................... EN 301 489-1 ......................................................................................................................................................................... EN 301 489-3 ....................................................................................................................................................................... EN 301 489-17 ................................................................................................................................................................................ RSS 210 Safety.......................................................... ................................................................................................. UL/EN 60950-1 ............................................................................................................................................................... CSA C22.2.60950-1 EQUIPMENT MODIFICATION CAUTION: Equipment changes or modifications not expressly approved by Sensormatic Electronics, LLC, the party responsible for FCC compliance, could void the user’s authority to operate the equipment and could create a hazardous condition. See About this guide on page 3. Other declarations WARRANTY DISCLAIMER: Sensormatic Electronics, LLC makes no representation or warranty with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose. Further, Sensormatic Electronics, LLC reserves the right to revise this publication and make changes from time to time in the content hereof without obligation of Sensormatic Electronics, LLC to notify any person of such revision or changes. LIMITED RIGHTS NOTICE: For units of the Department of Defense, all documentation and manuals were developed at private expense and no part of it was developed using Government Funds. The restrictions governing the use and disclosure of technical data marked with this legend are set forth in the definition of “limited rights” in paragraph (a) (15) of the clause of DFARS 252.227.7013. Unpublished - rights reserved under the Copyright Laws of the United States. TRADEMARK NOTICE: Sensormatic is a registered trademark of Sensormatic Electronics, LLC. Other product names mentioned herein may be trademarks or registered trademarks of Sensormatic or other companies. No part of this guide may be reproduced in any form without written permission from Sensormatic Electronics, LLC. WIRELESS DEVICE MODULE (BIX1000) INSTALLATION GUIDE 8200-1088-15, REV 3a 16 of 16 *8200-1088-15*
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes Author : Mary White & Aisling Burke Category : EAS Comments : Business Intelligence Module (BIM1000) Installation Guide, 8z108801a Company : Johnson Controls Create Date : 2018:03:20 15:00:15-04:00 Information Classification : Internal Keywords : BIM1000, BIX1000, BIM, BIX, controllers MSIP Label 6be 01c 0c-f 9b 3-4dc 4-af 0b-a 82110cc 37cd Application: Microsoft Azure Information Protection MSIP Label 6be 01c 0c-f 9b 3-4dc 4-af 0b-a 82110cc 37cd Enabled: True MSIP Label 6be 01c 0c-f 9b 3-4dc 4-af 0b-a 82110cc 37cd Extended MSFT Method: Automatic MSIP Label 6be 01c 0c-f 9b 3-4dc 4-af 0b-a 82110cc 37cd Name: Internal MSIP Label 6be 01c 0c-f 9b 3-4dc 4-af 0b-a 82110cc 37cd Ref: https://api.informationprotection.azure.com/api/a1f1e214-7ded-45b6-81a1-9e8ae3459641 MSIP Label 6be 01c 0c-f 9b 3-4dc 4-af 0b-a 82110cc 37cd Set By: jminats@jci.com MSIP Label 6be 01c 0c-f 9b 3-4dc 4-af 0b-a 82110cc 37cd Set Date: 2018-03-20T15:00:00.9607121-04:00 MSIP Label 6be 01c 0c-f 9b 3-4dc 4-af 0b-a 82110cc 37cd Site Id: a1f1e214-7ded-45b6-81a1-9e8ae3459641 Manager : Mark Evans Modify Date : 2018:03:20 15:00:22-04:00 Source Modified : D:20180320190001 Language : EN-US Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 5.4-c006 80.159825, 2016/09/16-03:31:08 Metadata Date : 2018:03:20 15:00:22-04:00 Creator Tool : Acrobat PDFMaker 11 for Word Document ID : uuid:b4c94db8-8774-48ef-b1e4-a014c932325d Instance ID : uuid:3ffd55d0-5d93-4c25-9750-6777d44fbed8 Subject : 17 Format : application/pdf Title : Business Intelligence Transciver (BIM1000) Installation Guide, 8z108801a Creator : Mary White & Aisling Burke Producer : Adobe PDF Library 11.0 Information 0020 Classification : Internal Page Layout : OneColumn Page Count : 16EXIF Metadata provided by EXIF.tools