USA Alo Branch RC-30 Measurement Insturment Remote Control User Manual manual

USA Alinco Branch Measurement Insturment Remote Control manual

manual

INSTRUCTION MANUALRemote Controller for RL-VH3 SeriesRC-30ForewordThank you for purchasing the TOPCON Remote controller RC-30.For the best performance of the instruments, please read these instruc-tions carefully and keep them in a convenient location for future refer-ence.Handling PrecautionsVibration and Impact Protectionwhen transporting the instrument, provide protection to minimize risk ofsevere vibration or impact. Display for Safe UseIn order to encourage the safe use of products and prevent any dangerto the operator and others or damage to properties, important warningsare put on the products and inserted in the instruction manuals.We suggest that everyone understand the meaning of the following dis-plays and icons before reading the “Safety Cautions” and text.1) Injury refers to hurt, burn, electric shock, etc.2) Physical damage refers to extensive damage to buildings or equipment and furniture.Safety Cautions SpecificationsNomenclatureKey FunctionsHow to Set Communication ChannelThe same communication channel mustbe assigned to both RC-30 and the RL-VH3 series.Remove the rubber cap and turn therotary switch to set a channel.How Replace the RC-30 Batteries1Remove the battery cover from the back of the RC-30 by pressing on the cover and sliding it in the direction of the arrow.2Remove the old batteries and replace with new three “AA” cell alkaline batteries making sure each is placed in the proper direction as indicated.3Replace the battery cover. You will hear a click when it snaps in place.Display MeaningWARNING Ignoring or disregard of this display may lead to death or serious injury.CAUTION Ignoring or disregard of this display may lead to personal injury or physical dam-age to the instrument.WARNING• There is a risk of fire, electric shock or physical harm if you attempt to disassemble or repair the instrument yourself.This is only to be carried out by TOPCON or an authorized dealer, only!• Risk of fire or electric shock.Do not use a wet battery or charger.• May ignite explosively.Never use an instrument near flammable gas, liquid matter, and do not use in a coal mine.• Battery can cause explosion or injury.Do not dispose in fire or heat.• The short circuit of a battery can cause a fire.Do not short circuit battery when storing it.CAUTIONDo not allow skin or clothing to come into contact with acid from the batteries, if this does occur then wash off with copious amounts of water and seek medical advice.Power source Three “AA” cell batteries DC4.5VOperating time Alkaline manganese dry batteriesApprox. 40 hours ( +20°C)Operating temperature -20°C to +50°C (-4°F to +122°F)Dimensions 157(L) x 64(W) x 34(H) mm(6.2 (L) x2.5 (W) x 1.3(H) ) inWeight 0.24kg (0.05 lbs)Transmission lamp Sends operation to the instrument.If the channel is not equal to the channel setat RL-VH3 side, the red lamp will light.Battery warning lamp for RC-30 Battery warning for RC-30. Replace the battery to new ones. Stop beam control Sets Stop beam mode and moves the laser. Speed control The rotation speed of the rotary head can bechanged.Alignment control Setting slope for horizontal rotation.Alignment of the line for vertical rotation.X/Y axis lamp An axis selected turns on.Power switch for RL-VH3 series On/Off of the RL-VH3series by pressing thiskey for more than three seconds.(Sleep mode on/off)Mode switch con-trol Laser mode is switched alternately as follows.Scan mode / Laser sensor mode / Laserpointing mode.If this key is pressed in other modes exceptScan, Laser sensor and Laser pointingmodes, the mode will change to scan mode. If this key is pressed in manual focus mode,manual focus will be cancelled. Manual focus con-trol Laser beam can be focused manually. (Only for RL-VH3A/G)X/Y axis selection Sets slope mode by pressing for more thanthree seconds. Select X or Y axis for manual grading.To cancel the slope mode press this key formore than three seconds. Note • Replace all 3 batteries with new ones.• Do not mix old batteries and new ones.Battery warning lampfor RC-30Transmission lampPower switch for RL-VH3 seriesMode switch control(RL-VH3G does not have Laser sensor mode.)Slope mode / X/Y axis selection X/Y axis lampAlignment controlSpeed controlStop beam control Manual focus control( Only for RL-VH3A/G) Rotary switch(with rubbercap)Battery cover (1a) RC-30 9910

Navigation menu