UTC Fire and Security Americas 612-H20PANIC 60-578 User Manual

Download:
Mirror Download [FCC.gov]
Document ID	2323931
Application ID	toTOk8JCPOfpw+ABvpCXzw==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	15.33kB (191599 bits)
Date Submitted	2014-07-13 00:00:00
Date Available	2014-07-13 00:00:00
Creation Date	2014-07-07 15:04:41
Producing Software	Acrobat Distiller 10.0.0 (Windows)
Document Lastmod	2014-07-07 15:04:41
Document Title	Microsoft Word - user_manual_in_english_fcc__ic.doc
Document Creator	PScript5.dll Version 5.2.2
Document Author:	valbertson

Learn Mode Water Resistant Pendant Panic
Button Installation Instructions
Introduction
Installation
This panic button can be used throughout the premises for
police, medical, or auxiliary alarm activation. When the sensor
button is pressed, the built-in transmitter sends a signal to the
panel (Figure 1 below).
You can mount the optional wall-mount holder, using anchors
and screws or double-sided tape.
To mount the holder with anchors and screws:
1.
Figure 1: 60-578 Pendant Panic Button
Place the holder on the wall at the desired location and
mark the mounting holes with a pencil (Figure 2 below).
Figure 2: Mounting with screws
Mounting hole
The water-resistant design helps prevent damage in case the
sensor accidently gets wet.
The sensor can be worn using the built-in belt clip or it can be
mounted on a wall in a location convenient for the customer,
using the optional wall-mount holder (kit number 80-116). Each
kit includes the following:
•
5 wall-mount holders;
•
5 pieces of double-sided tape;
•
10 plastic anchors; and
•
10 Phillips-head screws.
Mounting hole
2.
Secure the holder to the wall with the screws supplied.
Use the anchors supplied where studs are not present.
To mount the holder with double-sided tape:
1.
Peel off the colored backing from the double-sided tape
and place it on back of the holder (Figure 3 below).
Figure 3: Mounting with double-sided tape
You will also need a small Phillips screwdriver (if installing the
optional wall-mount holder).
Affix
tape
Installation guidelines
here
Use the following guidelines when installing this button:
•
The transmitter in the button has an open-air range of up
to 1,000 ft. (305 m), but the installation environment may
influence this range.
•
When mounting on a wall, determine the best location for
each panic button so it is easily accessible.
•
The 3.5 VDC lithium battery will last at least 12 months.
P/N 46-667 • REV J •23APR14
2.
Peel off the other backing and firmly press the holder
against the mounting surface.
Programming
This section describes the basic steps for adding the sensor to
panel memory. For complete instructions, refer to the specific
panel’s documentation.
To program the sensor:
1.
Set the panel in program mode.
2.
When prompted by the panel, enter the appropriate group
number (groups 00 through 07).
Note: Be sure to assemble the sensor correctly to ensure
water resistance. Be especially careful not to nick or
damage the rubber gasket lining.
4.
Test the sensor as described in “Sensor test” above.
Lithium battery disposal
Lithium batteries that are no longer usable are considered
hazardous waste. Be sure to properly dispose of the old
battery. Contact your local city government for hazardous
waste disposal laws.
Note: For UL installations where the holder is used, the
sensor must be added as a fixed type (sensor groups 00,
02, 04, or 05).
Specifications
Compatibility
All Interlogix Security Learn Mode panels
When prompted by the panel, select the desired sensor
number.
Power source
3.6 VDC Saft or Tekcell lithium battery
Enclosure
Water-resistant and shock-resistant
4.
When prompted by the panel, trip the sensor by pressing
the sensor button.
Dimensions (LxWxD)
2.25 x 1.75 x 0.75 in. (5.71 x 4.44 x 1.90 cm)
5.
Exit from program mode.
3.
Regulatory information
Manufacturer
UTC Fire & Security Americas Corporation, Inc.
1275 Red Fox Rd., Arden Hills, MN 55112-6943,
USA
FCC compliance
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any
interference received, including interference that
may cause undesired operation.
Changes or modifications not expressly approved
by Interlogix can void the user’s authority to
operate the equipment.
Sensor test
To test the sensor:
1.
Set the system to the Dealer Sensor Test mode.
2.
Press the button on the sensor.
3.
Count the number of signals received by the panel,
indicated by interior siren beeps. Seven to eight beeps are
considered acceptable.
4.
Test the sensor from several locations within the premises
to check for consistent response.
FCC ID: B4Z-612-H2OPANIC
IC compliance
This Class B digital apparatus complies with
Canadian ICES-003.
Cet appareil numérique de la classe B est
conforme à la norme NMB-003 du Canada.
Le fonctionnement est soumis aux deux
conditions suivantes : (1) cet appareil peut ne pas
provoquer d’interférences et (2) cet appareil doit
accepter toutes interférences, y compris les
interférences pouvant provoquer un
fonctionnement non désiré de l’appareil.
Battery replacement
To replace the sensor battery:
1.
To disassemble the sensor, remove the two screws on the
back of the sensor and separate the front and back plastic.
Caution: You must be free of static electricity before handling
the transmitter circuit board. Touch a grounded, bare metal
surface before touching the circuit board, or wear a grounding
strap.
2.
Remove the old battery from its holder and install the new
battery, observing polarity
Caution: Install only the same size and type of battery. Do not
substitute another size or type of battery.
3.
Reassemble the sensor.
IC: 1175C-612PANIC
U.S. patents
4,855,713, 4,864,636, and others pending.
Contact information
For contact information, see www.utcfireandsecurity.com or
www.interlogix.com.
For technical support, toll-free: 888.437.3287 in the US
including Alaska, Hawaii, Puerto Rico, and Canada. Outside
the toll-free area, contact your dealer.
Copyright © 2014 Interlogix, a UTC Fire & Security Company.
All rights reserved.
Learn Mode Water Resistant Pendant Panic Button Installation Instructions

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : valbertson
Create Date                     : 2014:07:07 15:04:41-07:00
Modify Date                     : 2014:07:07 15:04:41-07:00
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Format                          : application/pdf
Creator                         : valbertson
Title                           : Microsoft Word - user_manual_in_english_fcc__ic.doc
Creator Tool                    : PScript5.dll Version 5.2.2
Producer                        : Acrobat Distiller 10.0.0 (Windows)
Document ID                     : uuid:e12d4035-7209-4531-8845-c7d21d8e9079
Instance ID                     : uuid:c8da5d08-880e-429c-ad3f-81c788f66b7f
Page Count                      : 2

EXIF Metadata provided by EXIF.tools