UTC Fire and Security Americas 903-TCVR 319.5 MHz OEM Transceiver w/Crystal TX User Manual TechComm Style Guide

Download:
Mirror Download [FCC.gov]
Document ID	566530
Application ID	qyQHDKo3qvZjpjzFRDNRbw==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	4.33kB (54086 bits)
Date Submitted	2005-07-28 00:00:00
Date Available	2005-08-31 00:00:00
Creation Date	2005-04-04 06:58:08
Producing Software	Acrobat Distiller 7.0 (Windows)
Document Lastmod	2005-05-26 06:03:01
Document Title	TechComm Style Guide
Document Creator	FrameMaker 7.0
Document Author:	Matt Newman

600-1025 OEM Transceiver Module
Installation Instructions
466-2226B
May 2005
Description
The OEM transceiver modules are compatible with GE Security
wireless transmitters. The modules have an onboard receiver,
microprocessor, and connection for a daughter board. The microprocessor controls the receiver, providing antenna switching and
AGC functions. It also analyzes the received data from the
receiver, validates incoming packets, and returns packets to the
receiver when polled. A daughter board, which communicates
with the module via an 8-pin header, can be added to implement
a variety of functions.
Each module encapsulates the receiver functions and formats and
presents a common interface to the daughter board. Therefore,
even though protocols vary among the GE Security radio
frequencies used around the world, the interface is the same to
the daughter board.
Figure 2.
Antenna shrouds
600-1029 enclosure
Top latches
OEM transceiver
2 mm power jack
Installation guidelines
Terminal block
Observe the following guidelines when installing the OEM transceiver module:
• Allow at least 9 inches (22.9 cm) of clearance above the
enclosure for the antennas.
• Avoid mounting locations that expose the module to moisture.
• Avoid areas with excessive metal or electrical wiring
including furnace and utility rooms. If unavoidable, mount
on or near metal with the antenna extending above the
metallic surfaces as shown in Figure 1.
Figure 1.
ON
1 2 3 4 5 6 7 8
LEDs
Bottom latch
4.
Mounting on or near metal
Connect DC power to the OEM transceiver module using 2
mm power jacks (center positive) or connect flyleads to the
terminal block as labeled on the board.
Note:
Metal
Installing the circuit board
Metal
For model 600-1025-02-43, the cable length must be less than
3 m (9.8 ft.) for CE compliance.
LED operation
Table 1 shows the LED indications for the OEM transceiver
module.
Table 1.
Note:
For UL installations this module must be mounted in the 6001029 enclosure. Daughter boards have not been investigated
for use by UL.
OEM transceiver module LED indications
Indication
Green LED
Red LED
Powered up
On
Off
Communication with daughter baord
On
Flashing
Installation
Valid packet received
One flash off
Off or flashing
To mount the OEM transceiver module onto the back plate of the
600-1029 enclosure, do the following:
1. Insert the antennas into the antenna shrouds (Figure 2).
2. Gently slide the top of the circuit board under the two top
latches.
Troubleshooting
CAUTION
3.
You must be free of static electricity before
handling circuit boards. Wear a grounding strap
or touch a bare metal surface to discharge static
electricity.
Snap the circuit board in at the bottom latch to secure it in
place as shown in Figure 2.
The following table gives troubleshooting suggestions for the
OEM transceiver module.
Table 2.
OEM transceiver module troubleshooting
Problem
Action
OEM transceiver module’s green and
red LEDs are off
1. Check that the transformer is plugged
in.
2. Check the transformer to module
wiring.
OEM receiver module’s green LED is
on and the red LED is off
Check the daughter board mounting.
2
600-1025 OEM Transceiver Module
Installation Instructions
FCC compliance
CE declaration of conformity
This device complies with FCC Rules Part 15. Operation is subject to the following
two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference that may be received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by GE Security can void the
user’s authoriy to operate the equipment.
Manufacturer’s name:
GE Security
Specifications
Manufacturer’s address:
1275 Red Fox Road
Arden Hills, MN 55112
USA
EU representative:
All 319.5 MHz sensors
All 433 MHz sensors
GE Security B.V.
Kelvinstraat 7
6003 DH Weert
The Netherlands
Product indentification:
Product: 433 MHz OEM Transceiver
Model number: 600-1025-02-43
Brand: GE Security
45mA
100mA
1,000 feet (305 m)
R&TTE directive:
EMC:
Models
Frequency
600-1025-02-95R
600-1025-02-43
Sensor compatability
600-1025-02-95R
600-1025-02-43
Power required (without
daughter board)
Typical
Maximum
Wireless range
Listings
600-1025-02-95R
600-1025-02-43
Operating temperature
Storage temperature
Maximum relative humidity
Dimensions
Features
Enclosure
USB adaptor
Repeater adaptor
Stand-off
600-1025-02-95R and 600-1025-02-43
319.5 MHz
433.92 MHz
UL (985 1023), FCC ID (B4Z-875-TCVR), DoC,
IC: 867-875CVR
CE
32 to 140°F (0 to 60°C)
-30 to 140°F (-34 to 60°C)
90% noncondensing
3.2 x 4.6 x 0.6 inches (8.1 x 11.7 x 1.5 cm)
Antenna tamper, jam detect, wall tamper, cover
tamper
600-1029
59-873
600-1031
40-262
TUV 0123 / GE Security
Test report reference: CEQP-600-1025-02-43
Applied standards: EN50130-4 (1995) +A1
(1998)
Safety:
GE Security
Test report reference: CEQP-600-1025-02-43
Applied standards: EN60950-1:2001
Radio:
TUV 0123
Test report reference: CEQP 600-1025-02-43
Applied standards: EN300220-3 v1.1.1 (092000)
Equipment class identifier:
(RF products falling under the
scope of R&TTE)
None (class 1 product)
Means of conformity
We declare under our sole responsibility that this product is in conformity with
Directive 93/68/EEC (Marking) and/or complies to the essential requirements and
all other relevant provisions of the 1999/5/EC (R&TTE) based on test results using
(non) harmonized standards in accordance with the Directives mentioned.
Technical support
Toll-free: 888.437.3287 (US including Alaska and Hawaii; Puero Rico; Canada)
Outside the toll-free area: Contact your local dealer.
www.gesecurity.com

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Tagged PDF                      : Yes
Page Mode                       : UseOutlines
XMP Toolkit                     : 3.1-701
Producer                        : Acrobat Distiller 7.0 (Windows)
Marked                          : True
Create Date                     : 2005:04:04 06:58:08Z
Creator Tool                    : FrameMaker 7.0
Modify Date                     : 2005:05:26 06:03:01Z
Format                          : application/pdf
Creator                         : Matt Newman
Title                           : TechComm Style Guide
Document ID                     : uuid:acee9229-1312-4ec9-a407-e101a3b5a5b9
Instance ID                     : uuid:807b8e01-d46c-4540-ab27-0b1308aa70e3
Page Count                      : 2
Author                          : Matt Newman
Keywords                        : editing, spelling, formatting, standards

EXIF Metadata provided by EXIF.tools