Ubiquiti AF2X Digital Point-to-Point Radio User Manual airFiber X User Guide

Ubiquiti Networks, Inc. Digital Point-to-Point Radio airFiber X User Guide

user manual Part 4

Download: Ubiquiti AF2X Digital Point-to-Point Radio User Manual airFiber X User Guide
Mirror Download [FCC.gov]Ubiquiti AF2X Digital Point-to-Point Radio User Manual airFiber X User Guide
Document ID2713924
Application ID6xVt0krGfcI5vbKEUAJmSQ==
Document Descriptionuser manual Part 4
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize423.73kB (5296653 bits)
Date Submitted2015-08-13 00:00:00
Date Available2016-02-09 00:00:00
Creation Date2015-08-13 13:25:48
Producing SoftwareAdobe PDF Library 15.0
Document Lastmod2015-08-13 13:26:38
Document TitleairFiber X User Guide
Document CreatorAdobe InDesign CC 2015 (Macintosh)
Document Author: A Imaoka

airFiber® X User Guide
DATA Port Ethernet Settings
DATA Speed This is the speed of the Data port.
The default is Auto. The airFiber X radio automatically
negotiates transmission parameters, such as speed and
duplex, with its counterpart. In this process, the networked
devices first share their capabilities and then choose the
fastest transmission mode they both support.
To manually specify the maximum transmission link
speed and duplex mode, select one of the following
options: 100 Mbps‑Full, 100 Mbps‑Half, 10 Mbps‑Full, or
10 Mbps‑Half.
To disable the Ethernet data port, select Disabled.
Note: If Disabled is selected, ensure that the radio
is accessible using the Management Ethernet port
or over the RF link (with in-band management
enabled), or all communication with the radio will
be lost.
Full-duplex mode allows communication in both
directions simultaneously. Half-duplex mode allows
communication in one direction at a time, alternating
between transmission and reception.
Flow Control If enabled, the airFiber X radio generates
and responds to Ethernet layer PAUSE frames. The
airFiber X radio regulates inbound traffic from the
customer’s network to avoid buffer overflows within the
airFiber X radio. Flow control has the effect of controlling
the inter‑packet spacing of packets headed into the
airFiber Data interface.
Multicast Filter If enabled, the filter blocks multicast
traffic from overloading the CPU when in-band
management is enabled. This allows the airFiber X radio
to be managed in-band when the customer’s network is
carrying large volumes of multicast traffic, such as IPTV.
The filter does not block multicast traffic going over
the radio; it simply blocks it from reaching the airFiber’s
management interface CPU.
Track Radio Link If this option is enabled, the airFiber X
radio disconnects the Data port’s Ethernet link when the
RF link is lost (The Management port is never disabled by
this option). The Track Radio Link option is useful because
it quickly indicates a “link lost” condition to the customer’s
routing equipment (such as a direct connection to
OSPF‑enabled routers).
• Disabled The Track Radio Link option is disabled by
default. The Data port’s Ethernet link will always remain
up regardless of the RF link state.
Ubiquiti Networks, Inc.
Chapter 7: Advanced Tab
• Use Timeout Duration This option is designed for use
by operators who are using in-band management. Two
timers control the Data port’s Ethernet link.
RF Link
Ethernet Link
Notes
Goes down for
the first time
The Ethernet link goes
down and remains
down for the number
of seconds specified by
the Link Off Duration
timer.
Even if the RF link goes
back up before the
Link Off Duration timer
elapses, the Ethernet
link remains down.
The Ethernet link will
then come back up
so that the airFiber X
radio can be managed
even when the RF link
is down.
Goes down
for the
second time
The Ethernet link
remains up as long as
time remains on the
Link Off Spacing timer.
When the Link Off
Spacing timer elapses,
then the Ethernet link
goes down again for
the number of seconds
specified by the Link
Off Duration timer. (This
happens only if the RF
link is still down.)
The Ethernet link’s
downtime is long
enough to signal to
the customer’s routing
equipment that the
path is lost.
The Ethernet link’s
uptime is long enough
so the operator has
enough time to access
the airFiber X radio,
make configuration
changes, and save those
changes.
Sufficient Ethernet link
uptime is vital when a
RF link is constantly up
and down.
If the Use Timeout Duration option is enabled, the Track
Radio Link option and the following timers are enabled:
-- Link Off Duration The Link Off Duration timer
controls the length of time the Data port’s Ethernet
link will be down if the RF link goes down. Enter the
number of seconds that the Ethernet link should be
offline. For example, if this is set to 10 seconds, then
when the RF link goes down, the Ethernet link will go
down and remain down for 10 seconds (regardless of
the RF link state), and then it will go back up.
-- Link Off Spacing The Link Off Spacing timer controls
the length of time the airFiber X radio will wait before
allowing the Data port’s Ethernet link to go down for a
second time if the RF link goes down again. Enter the
minimum interval (in seconds) between offline events
of the Ethernet link, regardless of the RF link status.
The value for Link Off Spacing should be larger than the
value for Link Off Duration, and it should be enough
time for the operator to access the airFiber X radio,
make any configuration changes, and apply those
changes.
Note: If the Link Off Spacing timer is set to
0 seconds, then the Ethernet link will only use the
Link Off Duration timer. If the Link Off Duration
timer is set to 10 seconds and the RF link goes
down, then the Ethernet link will go down for
10 seconds and then go back up regardless of the
RF link state. If the RF link is still down, then the
Ethernet link will not go down again until the RF
link goes back up and then down again.
23
Chapter 7: Advanced Tab
Here are a couple of examples involving the use of the
Use Timeout Duration option.
airFiber® X User Guide
MGMT Port Ethernet Settings
• Example #1
• Link Off Duration 5 seconds
• Link Off Spacing 60 seconds
The Data port’s Ethernet link will be initially
disconnected when the RF link first goes down. That
event will start a 60‑second timer. The Ethernet link
will remain offline for 5 seconds (regardless of the RF
link status) and then come back online. The Ethernet
link will remain online (regardless of the RF link
state) until the 60‑second timer expires.
• Example #2
• Link Off Duration 20 seconds
• Link Off Spacing 120 seconds
The Data port’s Ethernet link will be initially
disconnected when the RF link first goes down. That
event will start a 120‑second timer. The RF link goes
back up after 10 seconds; however, that does not
affect the Ethernet link. The Ethernet link will remain
offline for 20 seconds and then come back online.
The RF link goes down again after 60 seconds;
however, that does not affect the Ethernet link.
The Ethernet link will then remain online until the
120‑second timer expires.
MGMT Speed This is the speed of the Management
port. By default, the option is Auto. The airFiber X radio
automatically negotiates transmission parameters, such as
speed and duplex, with its counterpart. In this process, the
networked devices first share their capabilities and then
choose the fastest transmission mode they both support.
To manually specify the maximum transmission link
speed and duplex mode, select one of the following
options: 100 Mbps‑Full, 100 Mbps-Half, 10 Mbps-Full,
or 10 Mbps‑Half. If you are running extra long Ethernet
cables, a link speed of 10 Mbps could help to achieve
better stability.
Full-duplex mode allows communication in both
directions simultaneously. Half-duplex mode allows
communication in one direction at a time, alternating
between transmission and reception.
• Enabled This option is designed for use by operators
who are not using in-band management. The Track
Radio Link option is enabled without timers, so the Data
port’s Ethernet link follows the RF link state exactly. If
the RF link goes down, then the Ethernet link goes down
and remains down until the RF link goes back up.
Minimum TX Capacity This is the minimum allowable TX
capacity before the link is dropped. If the capacity drops
below this threshold, the Ethernet link will be dropped.
If set to 0, then capacity will not be used; only the RF link
state will be used.
Minimum RX Capacity This is the minimum allowable RX
capacity before the link is dropped. If the capacity drops
below this threshold, the Ethernet link will be dropped.
If set to 0, then capacity will not be used; only the RF link
state will be used.
Capacity Window This is the number of continuous
seconds that the radio must remain under the minimum
TX or RX capacity before the link is dropped. If set to
0, then as soon as capacity drops below a set limit, the
Ethernet link will be dropped.
24
Ubiquiti Networks, Inc.
airFiber® X User Guide
Chapter 8: Services Tab
The Services tab configures system management services:
Ping Watchdog, SNMP Agent, Web Server, SSH Server, Telnet
Server, NTP Client, Dynamic DNS, System Log, and Device
Discovery.
Change To save or test your changes, click Change.
A new message appears. You have three options:
Chapter 8: Services Tab
the user-defined constraints, the airFiber X radio will
automatically reboot. This option creates a kind of
“fail‑proof” mechanism.
Ping Watchdog is dedicated to continuous monitoring of
the specific connection to the remote host using the Ping
tool. The Ping tool works by sending ICMP echo request
packets to the target host and listening for ICMP echo
response replies. If the defined number of replies is not
received, the tool reboots the airFiber X radio.
• Apply To immediately save your changes, click Apply.
• Test To try the changes without saving them, click Test.
To keep the changes, click Apply. If you do not click
Apply within 180 seconds (the countdown is displayed),
the airFiber X radio times out and resumes its earlier
configuration.
• Discard To cancel your changes, click Discard.
Ping Watchdog
Ping Watchdog sets the airFiber X radio to continuously
ping a user-defined IP address (it can be the Internet
gateway, for example). If it is unable to ping under
Ubiquiti Networks, Inc.
Ping Watchdog Enables use of Ping Watchdog.
• IP Address To Ping Specify the IP address of the target
host to be monitored by Ping Watchdog.
25
Chapter 8: Services Tab
• Ping Interval Specify the time interval (in seconds)
between the ICMP echo requests that are sent by Ping
Watchdog. The default value is 300 seconds.
airFiber® X User Guide
• Location Specify the airFiber X radio’s physical location.
Web Server
• Startup Delay Specify the initial time delay (in seconds)
until the first ICMP echo requests are sent by Ping
Watchdog. The default value is 300 seconds.
The Startup Delay value should be at least 60 seconds
as the network interface and wireless connection
initialization takes a considerable amount of time if the
airFiber X radio is rebooted.
• Failure Count to Reboot Specify the number of ICMP
echo response replies. If the specified number of ICMP
echo response packets is not received continuously,
Ping Watchdog will reboot the airFiber X radio. The
default value is 3.
• Save Support Info This generates a support
information file.
SNMP Agent
Simple Network Monitor Protocol (SNMP) is an application
layer protocol that facilitates the exchange of management
information between network devices. Network
administrators use SNMP to monitor network‑attached
devices for issues that warrant attention.
The following Web Server parameters can be set:
Secure Connection (HTTPS) If enabled, the Web Server
uses secure HTTPS mode.
• Secure Server Port If secure HTTPS mode is used,
specify the TCP/IP port of the Web Server.
Server Port If HTTP mode is used, specify the TCP/IP port
of the Web Server.
Session Timeout Specifies the maximum timeout before
the session expires. Once a session expires, you must log
in again using the username and password.
SSH Server
The airFiber X radio contains an SNMP Agent, which does
the following:
• Provides an interface for device monitoring using SNMP
• Communicates with SNMP management applications
for network provisioning
• Allows network administrators to monitor network
performance and troubleshoot network problems
The following SSH Server parameters can be set:
SSH Server This option enables SSH access to the
airFiber X radio.
• Server Port Specify the TCP/IP port of the SSH Server.
• Password Authentication If enabled, you must
authenticate using administrator credentials to grant
SSH access to the airFiber X radio; otherwise, an
authorized key is required.
For the purpose of equipment identification, configure the
SNMP Agent with contact and location information:
• Authorized Keys Click Edit to import a public key file
for SSH access to the airFiber X radio instead of using an
admin password.
SNMP Agent Enables the SNMP Agent.
• SNMP Community Specify the SNMP community
string. It is required to authenticate access to
Management Information Base (MIB) objects and
functions as an embedded password. The airFiber X
radio also supports a read-only community string;
authorized management stations have read access to
all the objects in the MIB except the community strings,
but do not have write access. The airFiber X radio
supports SNMP v1. The default SNMP Community is
public.
• Contact Specify the contact who should be notified in
case of emergency.
26
-- Choose File Click Choose File to locate the new key
file. Select the file and click Open.
-- Import Imports the file for SSH access.
-- Enabled Enables the specific key. All the added keys
are saved in the system configuration file; however,
Ubiquiti Networks, Inc.
airFiber® X User Guide
Chapter 8: Services Tab
only the enabled keys are active on the airFiber X
radio.
-- Type Displays the type of key.
-- Key Displays the key.
-- Comment You can enter a brief description of the key.
-- Action You have the following options:
• Add Adds a public key file.
• Edit Make changes to a public key file. Click Save to
save your changes.
• Del Deletes a public key file.
Dynamic DNS If enabled, the airFiber X radio allows
communications with the DDNS server.
• Host Name Enter the host name of the DDNS server.
• Username Enter the user name of the DDNS account.
-- Save Saves your changes.
• Password Enter the password of the DDNS account.
-- Close Discards your changes.
• Show Check the box to display the password
characters.
Telnet Server
System Log
The following Telnet Server parameters can be set:
Telnet Server This option activates Telnet access to the
airFiber X radio.
• Server Port Specify the TCP/IP port of the Telnet Server.
NTP Client
Network Time Protocol (NTP) is a protocol for
synchronizing the clocks of computer systems over
packet-switched, variable-latency data networks. You can
use it to set the system time on the airFiber X radio. If the
Log option is enabled, then the system time is reported
next to every log entry that registers a system event.
NTP Client Enables the airFiber X radio to obtain the
system time from a time server on the Internet.
• NTP Server Specify the IP address or domain name of
the NTP server.
Dynamic DNS
Domain Name System (DNS) translates domain names
to IP addresses; Each DNS server on the Internet holds
these mappings in its respective DNS database. Dynamic
Domain Name System (DDNS) is a network service that
notifies the DNS server in real time of any changes in the
airFiber X radio’s IP settings. Even if the airFiber X radio’s IP
address changes, you can still access the airFiber X radio
through its domain name.
Ubiquiti Networks, Inc.
System Log This option enables the registration routine
of system log (syslog) messages. By default it is disabled.
• Remote Log Enables the syslog remote sending
function. System log messages are sent to a remote
server, which is specified in the Remote Log IP Address
and Remote Log Port fields.
-- Remote Log IP Address The host IP address that
receives syslog messages. Properly configure the
remote host to receive syslog protocol messages.
-- Remote Log Port The TCP/IP port that receives syslog
messages. 514 is the default port for the commonly
used system message logging utilities.
Every logged message contains at least a system time and
host name. Usually a specific service name that generates
the system event is also specified within the message.
Messages from different services have different contexts
and different levels of detail. Usually error, warning, or
informational system service messages are reported;
however, more detailed debug level messages can also
be reported. The more detailed the system messages
reported, the greater the volume of log messages
generated.
27
Chapter 8: Services Tab
airFiber® X User Guide
Device Discovery
Discovery Enables device discovery, so the airFiber X
radio can be discovered by other Ubiquiti devices through
the Discovery tool.
CDP Enables Cisco Discovery Protocol (CDP)
communications, so the airFiber X radio can send out CDP
packets to share its information.
28
Ubiquiti Networks, Inc.
airFiber® X User Guide
Chapter 9: System Tab
The System tab contains administrative options. This
page enables the administrator to reboot the airFiber X
radio, reset it to factory defaults, upload new firmware,
back up or update the configuration, and configure the
administrator account.
Chapter 9: System Tab
Firmware Update
The controls in this section manage firmware
maintenance.
Change To save or test your changes, click Change.
A new message appears. You have three options:
Firmware Version Displays the current firmware version.
• Apply To immediately save your changes, click Apply.
Build Number Displays the build number of the firmware
version.
• Test To try the changes without saving them, click Test.
To keep the changes, click Apply. If you do not click
Apply within 180 seconds (the countdown is displayed),
the airFiber X radio times out and resumes its earlier
configuration.
• Discard To cancel your changes, click Discard.
Check for Updates By default, the firmware automatically
checks for updates. To manually check for an update, click
Check Now.
Upload Firmware Click this button to update the
airFiber X radio with new firmware.
The airFiber X radio firmware update is compatible with
all configuration settings. The system configuration is
preserved while the airFiber X radio is updated with a new
firmware version. However, we recommend that you back
up your current system configuration before updating the
firmware.
Ubiquiti Networks, Inc.
29
Chapter 9: System Tab
This is a three-step procedure:
1. Click Choose File to locate the new firmware file. Select
the file and click Open.
2. Click Upload to upload the new firmware to the
airFiber X radio.
airFiber® X User Guide
System Accounts
You can change the administrator password to protect
your device from unauthorized changes. We recommend
that you change the default administrator password when
initially configuring the device.
3. The Uploaded Firmware Version is displayed. Click
Update to confirm.
If the firmware update is in process, you can close the
firmware update window, but this does not cancel the
firmware update. Please be patient, as the firmware
update routine can take three to seven minutes. You
cannot access the airFiber X radio until the firmware
update routine is completed.
WARNING: Do not power off, do not reboot, and do
not disconnect the airFiber X radio from the power
supply during the firmware update process as these
actions will damage the airFiber X radio!
Device
The Device Name (host name) is the system-wide device
identifier. The SNMP agent reports it to authorized
management stations. The Device Name will be used in
popular router operating systems, registration screens,
and discovery tools.
Administrator Username Specifies the name of the
administrator.
Key icon Click this icon to change the administrator
password.
• Current Password Enter the current password for
the administrator account. It is required to change the
Password or Administrator Username.
• New Password Enter the new password for the
administrator account.
• Verify New Password Re-enter the new password for
the administrator account.
Note: The password length is 8 characters
maximum; passwords exceeding 8 characters will be
truncated.
Device Name Specifies the host name.
Interface Language Allows you to select the language
displayed in the web management interface. English is the
default language.
Date Settings
Read-Only Account Check the box to enable the
read‑only account, which can only view the Main tab.
Configure the username and password to protect your
device from unauthorized changes.
• Read-Only Account Name Specifies the name of the
system user.
• Key icon Click this icon to change the read-only
password.
-- New Password Enter the new password for the
read‑only account.
-- Show Check the box to display the read-only
password characters.
Time Zone Specifies the time zone in relation to
Greenwich Mean Time (GMT).
Miscellaneous
Startup Date When enabled, you are able to change the
airFiber X radio’s startup date.
• Startup Date Specifies the airFiber X radio’s startup
date. Click the Calendar icon or manually enter the
date in the following format: 2-digit month/2-digit
day/4‑digit year. For example, for January 5, 2014, enter
01/05/2014 in the field.
30
Reset Button To allow use of the airFiber X radio’s
physical reset button, check the box. To prevent an
accidental reset to default settings, uncheck the box.
Note: You can reset the airFiber X radio to default
settings via the airFiber Configuration Interface. Go
to the System tab > Reset to Defaults.
Ubiquiti Networks, Inc.
airFiber® X User Guide
Location
After the on-board GPS determines the location of the
airFiber X radio, its latitude and longitude are displayed.
If the GPS does not have a fix on its location, then
“Searching for Satellites” will be displayed.
Latitude The latitude of the airFiber X radio’s location is
displayed.
Longitude The longitude of the airFiber X radio’s location
is displayed.
Chapter 9: System Tab
We recommend that you back up your current system
configuration before uploading the new configuration.
Upload Click this button to upload the new configuration
file to the airFiber X radio. Click Apply to confirm.
After the airFiber X radio reboots, the settings of the
new configuration are displayed in the Wireless, Network,
Advanced, Services, and System tabs of the airFiber
Configuration Interface.
Reset to Factory Defaults Resets the airFiber X radio to
the factory default settings. This option will reboot the
airFiber X radio, and all factory default settings will be
restored. We recommend that you back up your current
system configuration before resetting the airFiber X radio
to its defaults.
Device Maintenance
The controls in this section manage the airFiber X radio
maintenance routines: reboot and support information
reports.
Reboot Device Initiates a full reboot cycle of the
airFiber X radio. Reboot is the same as the hardware
reboot, which is similar to the power-off and power-on
cycle. The system configuration stays the same after the
reboot cycle completes. Any changes that have not been
applied are lost.
Support Info This generates a support information
file that the Ubiquiti support engineers can use when
providing customer support. This file only needs to be
generated at their request.
Configuration Management
The controls in this section manage the airFiber X radio
configuration routines and the option to reset the
airFiber X radio to factory default settings.
The airFiber X radio configuration is stored in a plain
text file (.cfg file). You can back up, restore, or update the
system configuration file:
Back Up Configuration Click Download to download the
current system configuration file.
Upload Configuration Click Choose File to locate the
new configuration file. Select the file and click Open.
Ubiquiti Networks, Inc.
31
Chapter 10: Tools
Chapter 10: Tools
Each tab of the airFiber Configuration Interface contains
network administration and monitoring tools. Click the
Tools drop‑down list at the top right corner of the page.
Align Antenna
Use the Align Antenna tool to point and optimize the
antenna in the direction of maximum link signal. The
Antenna Alignment window is designed to refresh every
250 milliseconds.
32
airFiber® X User Guide
Chain 0/1 (Actual/Ideal) Displays the absolute power
level (in dBm) of the received signal for each chain.
Note: If “Overload” is displayed to indicate an
overload condition, identify and eliminate any
sources of strong in‑band interference.
Remote Chain 0/1 (Actual/Ideal) Displays the absolute
power level (in dBm) of the received signal for each chain
of the remote airFiber X radio.
Max Signal Displays the maximum signal strength (in
dBm). To adjust the range of the Max Signal meter, use
the slider or manually enter the new value. If you reduce
the range, the color change will be more sensitive to
signal fluctuations, indicating the offset of the maximum
indicator value and the scale itself.
Ubiquiti Networks, Inc.
airFiber® X User Guide
Discovery
The Device Discovery tool searches for all Ubiquiti devices
on your network. The Search field automatically filters
devices containing specified names or numbers as you
enter them.
Chapter 10: Tools
Packet Count Enter the number of packets to send for
the ping test.
Packet Size Specify the size of the packet.
Start Click this button to start the test.
Packet loss statistics and latency time evaluation are
displayed after the test is completed.
Traceroute
The Traceroute tool traces the hops from the airFiber X
radio to a specified outgoing IP address. Use this tool to
find the route taken by ICMP packets across the network
to the destination host.
It reports the MAC Address, Device Name, Mode, SSID,
Product type, Firmware version, and IP Address for each
Ubiquiti device. To access a device configuration through
its web management interface, click the device’s IP
address.
To refresh the window, click Scan.
Ping
You can ping other devices on the network directly from
the airFiber X radio. The Ping tool uses ICMP packets to
check the preliminary link quality and packet latency
estimation between two network devices.
Destination Host Enter the IP address of the
destination host.
Resolve IP Addresses Select this option to resolve the IP
addresses symbolically rather than numerically.
Start Click this button to start the test.
Responses are displayed after the test is completed.
airView
Use the airView Spectrum Analyzer to analyze the noise
environment of the radio spectrum and intelligently select
the optimal frequency to install a PtP airFiber link.
There are two system requirements for the airView
Spectrum Analyzer:
• Your system is connected to the device via Ethernet.
Launching airView will terminate all wireless
connections on the device.
• Java Runtime Environment 1.6 (or above) is required on
your client machine to use airView.
On first use, the following window appears.
Network Ping
Select Destination IP You have two options:
• Select a remote system IP from the drop-down list,
which is generated automatically.
• Select specify manually and enter the IP address in the
field displayed below the option.
Ubiquiti Networks, Inc.
• Do NOT warn me about this in the future Check the
box to bypass this window in future launches of the
airView Spectrum Analyzer.
33
Chapter 10: Tools
• Launch airView Click Launch airView to download the
Java Network Launch Protocol (jnlp) file and complete
the launch of airView.
airFiber® X User Guide
View Menu
Enable Chart Panel 1 (top) Displays the Waterfall or
Channel Usage chart in Chart Panel 1, depending on
which option you have selected in Preferences. This
time‑based graph shows the aggregate energy collected
or channel usage for each frequency since the start of the
airView session.
Enable Chart Panel 2 (middle) Displays the Waveform
chart in Chart Panel 2. This time-based graph shows the RF
signature of the noise environment since the start of the
airView session. The energy color designates its amplitude.
Cooler colors represent lower energy levels (with blue
representing the lowest levels) in that frequency bin, and
warmer colors (yellow, orange, or red) represent higher
energy levels in that frequency bin.
Main View
Device Displays the device name, MAC (Media Access
Control) address, and IP address of the device running
airView.
Total RF Frames Displays the total number of Radio
Frequency (RF) frames gathered since the start of the
airView session or since the Reset All Data button was last
clicked.
FPS Displays the total number of frames per second (FPS)
gathered since the start of the airView session or since
the Reset All Data button was last clicked. The wider the
interval amplitude, the fewer the FPS will be gathered.
Enable Chart Panel 3 (bottom) Displays the Real-time
chart (traditional spectrum analyzer) in Chart Panel 3.
Energy (in dBm) is shown in real time as a function of
frequency.
Note: Energy is the power ratio in decibels (dB) of the
measured power referenced to one milliwatt (mW).
Clear All Markers Resets all previously assigned
markers. Markers are assigned by clicking a point, which
corresponds with a frequency on the Real-time chart.
Preferences Changes airView settings, such as enabling
or disabling charts and traces, or specifying the frequency
interval.
Preferences
Select View > Preferences to display the Preferences airView Spectrum Analyzer window.
Reset All Data Click to reset all gathered data. Use this
option to analyze the spectrum for another location or
address.
File Menu
Click Exit to end the airView session.
34
Ubiquiti Networks, Inc.
airFiber® X User Guide
Charts
Chapter 10: Tools
Enable Waveform chart (middle) Check the box to
enable the middle chart. This time-based graph shows
the RF signature of the noise environment since the
start of the airView session. The energy color designates
its amplitude. Cooler colors represent lower energy
levels (with blue representing the lowest levels) in that
frequency bin, and warmer colors (yellow, orange, or red)
represent higher energy levels in that frequency bin.
The spectral view over time will display the steady-state RF
energy signature of a given environment.
Enable Real-time chart (bottom) Check the box to
enable the bottom chart. This graph displays a traditional
spectrum analyzer in which energy (in dBm) is shown in
real time as a function of frequency. There are three traces
in this view:
• Current (Yellow) Shows the real-time energy seen by
the device as a function of frequency.
• Average (Green) Shows the running average energy
across frequency.
• Maximum (Blue) Shows updates and maximum power
levels across frequency.
Real-Time Traces
Enable top chart Check the box to enable the top chart.
Select the desired chart to display in the top chart panel
on the main view. There are two options:
• Waterfall This time-based graph shows the aggregate
energy collected for each frequency since the start
of the airView session. The energy color designates
its amplitude. Cooler colors represent lower energy
levels (with blue representing the lowest levels)
in that frequency bin, and warmer colors (yellow,
orange, or red) represent higher energy levels in that
frequency bin.
The Waterfall View’s legend (top-right corner) provides
a numerical guide associating the various colors to
power levels (in dBm). The low end of that legend (left)
is always adjusted to the calculated noise floor, and the
high end (right) is set to the highest detected power
level since the start of the airView session.
• Channel Usage For each channel, a bar displays a
percentage showing the relative “crowdedness” of
that specific channel. To calculate this percentage, the
airView Spectrum Analyzer analyzes both the popularity
and strength of RF energy in that channel since the start
of an airView session.
Note: airFiber X radio channels are not related
to Wi‑Fi channels which are determined by IEEE
standards. airFiber X radio channels are numbered
consecutively starting with 0 and are 28 MHz in
width.
Ubiquiti Networks, Inc.
The following settings apply only to the Real-time chart:
Current Real-time Trace Check the Enable box to enable
the real-time trace. When enabled, the yellow outline on
the Real-time chart represents the real-time power level of
each frequency. The refresh speed depends on the FPS.
35
Chapter 10: Tools
airFiber® X User Guide
Averages Trace Check the Enable box to enable the
averages trace. When enabled, the averages trace is
represented by the green area on the Real-time chart,
which displays the average received power level data
since the start of the airView session. To enable a shaded
green area, check the Shaded Area box. To display only
a green outline without the shaded area, uncheck the
Shaded Area box.
Maximum Power Levels Trace Check the Enable box to
enable the maximum power trace. When enabled, the
maximum power trace is represented by the blue area on
the Real-time chart, which displays the maximum received
power level data since the start of the airView session. To
enable a shaded blue area, check the Shaded Area box.
To display only a blue outline without the shaded area,
uncheck the Shaded Area box.
Frequency Range Select the amplitude of the
frequency interval to be scanned from the Frequency
Range drop‑down list. Available frequencies are devicedependent. There are pre-defined ranges for the most
popular bands. You can enter a custom range; select
Custom Range from the Frequency Range drop-down list
and enter the desired values in the Start and End fields.
36
Ubiquiti Networks, Inc.
airFiber® X User Guide
Appendix A: Specifications
Appendix A: Specifications
airFiber AF‑2X
Dimensions
Weight
RF Connectors
GPS Antenna
Max. Conducted TX Power
Power Supply
Power Method
Mounting
Certifications
Operating Temperature
224 x 82 x 48 mm (8.82 x 3.23 x 1.89")
0.35 kg (0.77 lb)
(2) RP-SMA Weatherproof (CH0, CH1)
(1) SMA Weatherproof (GPS)
External, Magnetic Base
29 dBm
(Depends on Regulatory Region)
24V, 1A PoE Gigabit Adapter (Included)
Passive Power over Ethernet
Rocket Mount Compatible
GPS Pole Mount (Included)
FCC Part 15.247
CE EN 300328 v1.8.1
-40 to 55° C (-40 to 131° F)
Networking Interface
Data Port
Management Port
(1) 10/100/1000 Ethernet Port
(1) 10/100 Ethernet Port
System
Maximum Throughput
Encryption
OS
Wireless Modes
500 Mbps
128-bit AES
airOS F
Master/Slave
Radio
Operating Frequency
2400-2500 MHz
(Depends on Regulatory Region)
Frequency Accuracy
± 2.5 ppm without GPS Synchronization
± 0.2 ppm with GPS Synchronization
Channel Bandwidth
3.5 MHz, 5 MHz, 7.0 MHz, 10 MHz, 14 MHz, 20 MHz, 28 MHz, 30 MHz, 40 MHz, 50 MHz,
and 56 MHz Selectable
Programmable Uplink and Downlink Duty Cycles
Ubiquiti Networks, Inc.
37
Appendix A: Specifications
airFiber® X User Guide
airFiber AF‑3X
Dimensions
Weight
RF Connectors
GPS Antenna
Max. Conducted TX Power
Power Supply
Power Method
Mounting
Certifications
Operating Temperature
224 x 82 x 48 mm (8.82 x 3.23 x 1.89")
0.35 kg (0.77 lb)
(2) RP-SMA Weatherproof (CH0, CH1)
(1) SMA Weatherproof (GPS)
External, Magnetic Base
29 dBm
(Depends on Regulatory Region)
24V, 1A PoE Gigabit Adapter (Included)
Passive Power over Ethernet
Rocket Mount Compatible
GPS Pole Mount (Included)
FCC Part 90 Z
CE EN 302 217-2-2
-40 to 55° C (-40 to 131° F)
Networking Interface
Data Port
Management Port
(1) 10/100/1000 Ethernet Port
(1) 10/100 Ethernet Port
System
Maximum Throughput
Encryption
OS
Wireless Modes
500 Mbps
128-bit AES
airOS F
Master/Slave
Radio
Operating Frequency
3300-3900 MHz
(Depends on Regulatory Region)
Frequency Accuracy
± 2.5 ppm without GPS Synchronization
± 0.2 ppm with GPS Synchronization
Channel Bandwidth
3.5 MHz, 5 MHz, 7.0 MHz, 10 MHz, 14 MHz, 20 MHz, 28 MHz, 30 MHz, 40 MHz, 50 MHz,
and 56 MHz Selectable
Programmable Uplink and Downlink Duty Cycles
38
Ubiquiti Networks, Inc.
airFiber® X User Guide
Appendix A: Specifications
airFiber AF‑5X
Dimensions
Weight
RF Connectors
GPS Antenna
Max. Conducted TX Power
Power Supply
Power Method
Mounting
Certifications
Operating Temperature
224 x 82 x 48 mm (8.82 x 3.23 x 1.89")
0.35 kg (0.77 lb)
(2) RP-SMA Weatherproof (CH0, CH1)
(1) SMA Weatherproof (GPS)
External, Magnetic Base
26 dBm
(Depends on Regulatory Region)
24V, 1A PoE Gigabit Adapter (Included)
Passive Power over Ethernet
Rocket Mount Compatible
GPS Pole Mount (Included)
FCC Part 15.407
CE EN 302502 v1.2.1, EN 301 893 v1.7.1
-40 to 55° C (-40 to 131° F)
Networking Interface
Data Port
Management Port
(1) 10/100/1000 Ethernet Port
(1) 10/100 Ethernet Port
System
Maximum Throughput
Encryption
OS
Wireless Modes
500 Mbps
128-bit AES
airOS F
Master/Slave
Radio
Operating Frequency
5150-5950 MHz
(Depends on Regulatory Region)
Frequency Accuracy
± 2.5 ppm without GPS Synchronization
± 0.2 ppm with GPS Synchronization
Channel Bandwidth
10 MHz, 20 MHz, 30 MHz, 40 MHz, 50 MHz Selectable
Programmable Uplink and Downlink Duty Cycles
Ubiquiti Networks, Inc.
39
Appendix B: Listen Before Talk
Appendix B: Listen Before Talk
Note: This appendix applies to the airFiber AF-3X
radio only.
Introduction
Listen Before Talk (LBT) is a requirement for the 3.6 GHz
band in North America and Canada.
Because exclusive licenses for the 3650-3700 MHz band
are not granted within the United States, operators must
take steps to minimize potential interference in this band.
LBT refers to a contention-based protocol (CBP) that
requires a device to check if the transmission channel is in
use (listen) before it can initiate a transmission (talk). FCC
standards that relate to LBT include the following:
• FCC Part 90, Subpart Z requires 3.6 GHz systems to
implement a contention-based protocol to provide
LBT capability. This same requirement has also been
adopted by Industry Canada (IC).
• FCC Part 90, Subpart Z defines two categories of
contention-based protocols, restricted and unrestricted:
-- Restricted contention-based protocol This is a
protocol that can detect interference from products
that use a similar contention technology. Systems
using a restricted contention-based protocol operate
in the lower 25 MHz of the frequency band (36503675 MHz).
-- Unrestricted contention-based protocol This is a
protocol that can detect interference from products
that use a dissimilar contention technology. Systems
using an unrestricted contention-based protocol use
the full 50 MHz (3650-3700 MHz) of the frequency
band.
Unrestricted Protocol Description
The AF-3X Master/Slave system uses dedicated logic for
the LBT protocol, which is embedded into a TDD frame
structure. Energy detection is done at the beginning of
the TX defined by the frame structure of the air interface,
at intervals of 2.0, 2.5, 4.0, or 5.0 ms for compatibility
between various other Part 90Z radio devices.
Threshold Detection To Determine
Occupancy
The AF-3X averages the energy detected over a fixed listen
time and compares it to a preconfigured threshold value.
This threshold is configured for values that are within
the linear portion of the radio’s Receive Signal Strength
Indicator (RSSI) dynamic range.
The energy detection threshold is proportional to the
transmitter’s maximum transmit power. For example, if the
transmitter’s EIRP is 23 dBm, then the detection threshold
at the receiver’s input (assuming antenna gain of 0 dBi) is
-73 dBm/MHz.
40
airFiber® X User Guide
The detection threshold is adjusted as follows:
DT = -73 dBm/MHz + 10log10(B) + 23 – PT + A
where:
DT
PT
Detection Threshold in dBm
Monitored bandwidth in MHz
Maximum transmit power in dBm EIRP
Receive antenna gain in dBi
The receive antenna gain A is set equal to the external
antenna gain. The following are set by the operator during
the configuration of the AF-3X radio:
• maximum desired EIRP power PT
• external antenna gain A
• channel bandwidth B
The AF-3X ensures that the sum of the actual conducted
power and the external antenna gain used to calculate PT
does not exceed the regulatory EIRP limit.
The Master/Slave device makes an average measurement
during its Tx and samples the channel every frame
(typically 2.0 ms) to accumulate a co-channel signal
measurement. A typical accumulation period is 5 µs.
The bandwidth used for all channel occupancy
measurements is the same bandwidth used for system
operation and is configurable for values that range from
3.5 MHz to 40 MHz.
The detection threshold is configured to scale
automatically based on the in-use modulation level that
the system negotiates. The threshold level is automatically
set by the radio to meet regulatory requirements. All
threshold levels are normalized to a 0 dBi reference level.
The detection system uses the same hardware as the
actual radio lower-level software code and is therefore
operational over the same power range.
The AF-3X point-to-point system employs a proprietary
media access layer (MAC) that utilizes a TDD scheduled
transmission which is synchronized. Both the Master
and Slave employ a threshold detection mechanism
to monitor for other systems running within a selected
channel.
Action Taken When Occupancy is
Determined
Upon detection of occupancy, the Master will cease
transmission. It will continue to monitor the channel to
see if at any point that it becomes available.
Hidden-node problems are avoided by the AF-3X system’s
proprietary media access control (MAC) layer that utilizes
a TDD scheduled transmission (a synchronized framed
transmission). The Slave device cannot transmit until it
is allocated bandwidth from the Master device. If the
Master device detects co-channel signals, the uplink for
the scheduled slot allocation is not granted to the Slave,
preventing the Slave from transmitting. Since permission
to transmit is granted by the Master, there is no hidden
node problem like that experienced by Wi-Fi systems
which employ a contention-based protocol.
Ubiquiti Networks, Inc.
airFiber® X User Guide
Appendix B: Listen Before Talk
Opportunities for Other Transmitters
to Operate
No differences are performed between start-up mode
and operational mode. The Master/Slave device goes
into an energy scanning mode where it is allowed to do
one full cycle of energy detection before it is allowed to
transmit. The scan is a mode where the average energy
is accumulated to compare against the programmed
detection threshold. If the energy detected is less than the
detection threshold, the Master/Slave device is allowed to
make a transmission.
In normal operational mode the system does not allow
any transmission once the threshold has been detected.
Once the energy is no longer present will the system
begin to transmit again.
The Master and Slave uses the energy detected prior to
each transmit frame to control the muting of the transmit
function.
At any load level (no load, typical, or overload), the
system transmits data based on the configuration for the
uplink/downlink ratio The same amount of bandwidth is
reserved for channel detection, so performance remains
unaffected.
If there are two AF-3X systems on a co-channel, they
would share the spectrum as follows:
• Since the system is a synchronized frame-based system,
both systems would operate effectively with each other
because each system can be configured to transmit and
receive at the same point in time. The system uses a
GPS synchronization to time-align the start-of-frame for
all systems deployed.
• If the users configure the number of uplink and
downlink slots and the duty cycle (uplink/downlink
ratio) in an identical manner and each system uses the
same set of uncommitted uplink slots for the detection
sampling interval, then the two systems will co-exist
with no knowledge of the others presence.
• Each system listens prior to transmit and if it detects
activity yields to the other system.
• The system will shut down when the accumulated
energy is above the detection threshold and will
continue to transmit if it is below the detection
threshold. When the co-channel system is clear of the
channel then the target system will go back into regular
operation. Regular operation will consist of a constant
averaging of the energy detected in the uplink slots.
Ubiquiti Networks, Inc.
41
Appendix C: Safety Notices
airFiber® X User Guide
Appendix C: Safety Notices
1. Read, follow, and keep these instructions.
2. Heed all warnings.
3. Only use attachments/accessories specified by the
manufacturer.
WARNING: Do not use this product in location that can be
submerged by water.
WARNING: Avoid using this product during an electrical
storm. There may be a remote risk of electric shock from
lightning.
Electrical Safety Information
1. Compliance is required with respect to voltage,
frequency, and current requirements indicated on the
manufacturer’s label. Connection to a different power
source than those specified may result in improper
operation, damage to the equipment or pose a fire
hazard if the limitations are not followed.
2. There are no operator serviceable parts inside this
equipment. Service should be provided only by a
qualified service technician.
3. This equipment is provided with a detachable power
cord which has an integral safety ground wire intended
for connection to a grounded safety outlet.
a. Do not substitute the power cord with one that
is not the provided approved type. Never use an
adapter plug to connect to a 2-wire outlet as this
will defeat the continuity of the grounding wire.
b. The equipment requires the use of the ground wire
as a part of the safety certification, modification or
misuse can provide a shock hazard that can result in
serious injury or death.
c. Contact a qualified electrician or the manufacturer
if there are questions about the installation prior to
connecting the equipment.
d. Protective earthing is provided by Listed AC
adapter. Building installation shall provide
appropriate short-circuit backup protection.
e. Protective bonding must be installed in accordance
with local national wiring rules and regulations.
42
Ubiquiti Networks, Inc.
airFiber® X User Guide
Appendix D: Warranty
Limited Warranty
UBIQUITI NETWORKS, Inc (“UBIQUITI NETWORKS”)
warrants that the product(s) furnished hereunder (the
“Product(s)”) shall be free from defects in material and
workmanship for a period of one (1) year from the date
of shipment by UBIQUITI NETWORKS under normal use
and operation. UBIQUITI NETWORKS’ sole and exclusive
obligation and liability under the foregoing warranty
shall be for UBIQUITI NETWORKS, at its discretion, to
repair or replace any Product that fails to conform to the
above warranty during the above warranty period. The
expense of removal and reinstallation of any Product is
not included in this warranty. The warranty period of any
repaired or replaced Product shall not extend beyond its
original term.
Warranty Conditions
The above warranty does not apply if the Product:
(I) has been modified and/or altered, or an addition
made thereto, except by Ubiquiti Networks, or
Ubiquiti Networks’ authorized representatives, or as
approved by Ubiquiti Networks in writing;
(II) has been painted, rebranded or physically modified in
any way;
(III) has been damaged due to errors or defects in cabling;
(IV) has been subjected to misuse, abuse, negligence,
abnormal physical, electromagnetic or electrical
stress, including lightning strikes, or accident;
(V) has been damaged or impaired as a result of using
third party firmware;
(VI) has no original Ubiquiti MAC label, or is missing any
other original Ubiquiti label(s); or
(VII) has not been received by Ubiquiti within 30 days of
issuance of the RMA.
In addition, the above warranty shall apply only if: the
product has been properly installed and used at all times
in accordance, and in all material respects, with the
applicable Product documentation; all Ethernet cabling
runs use CAT5 (or above), and for outdoor installations,
shielded Ethernet cabling is used, and for indoor
installations, indoor cabling requirements are followed.
WARNING: Failure to properly ground your
airFiber units will void your warranty. (Please
follow the instructions on “Install a Ground Wire”
on page 5 for installation of the ground wires.)
Ubiquiti Networks, Inc.
Appendix D: Warranty
Returns
No Products will be accepted for replacement or repair
without obtaining a Return Materials Authorization (RMA)
number from UBIQUITI NETWORKS during the warranty
period, and the Products being received at UBIQUITI
NETWORKS’ facility freight prepaid in accordance with the
RMA process of UBIQUITI NETWORKS. Products returned
without an RMA number will not be processed and will be
returned freight collect or subject to disposal. Information
on the RMA process and obtaining an RMA number can be
found at: www.ubnt.com/support/warranty.
Disclaimer
EXCEPT FOR ANY EXPRESS WARRANTIES PROVIDED
HEREIN, UBIQUITI NETWORKS, ITS AFFILIATES, AND ITS
AND THEIR THIRD PARTY DATA, SERVICE, SOFTWARE AND
HARDWARE PROVIDERS HEREBY DISCLAIM AND MAKE
NO OTHER REPRESENTATION OR WARRANTY OF ANY
KIND, EXPRESS, IMPLIED OR STATUTORY, INCLUDING,
BUT NOT LIMITED TO, REPRESENTATIONS, GUARANTEES,
OR WARRANTIES OF MERCHANTABILITY, ACCURACY,
QUALITY OF SERVICE OR RESULTS, AVAILABILITY,
SATISFACTORY QUALITY, LACK OF VIRUSES, QUIET
ENJOYMENT, FITNESS FOR A PARTICULAR PURPOSE AND
NON-INFRINGEMENT AND ANY WARRANTIES ARISING
FROM ANY COURSE OF DEALING, USAGE OR TRADE
PRACTICE IN CONNECTION WITH SUCH PRODUCTS
AND SERVICES. BUYER ACKNOWLEDGES THAT NEITHER
UBIQUITI NETWORKS NOR ITS THIRD PARTY PROVIDERS
CONTROL BUYER’S EQUIPMENT OR THE TRANSFER OF
DATA OVER COMMUNICATIONS FACILITIES, INCLUDING
THE INTERNET, AND THAT THE PRODUCTS AND SERVICES
MAY BE SUBJECT TO LIMITATIONS, INTERRUPTIONS,
DELAYS, CANCELLATIONS AND OTHER PROBLEMS
INHERENT IN THE USE OF COMMUNICATIONS FACILITIES.
UBIQUITI NETWORKS, ITS AFFILIATES AND ITS AND THEIR
THIRD PARTY PROVIDERS ARE NOT RESPONSIBLE FOR ANY
INTERRUPTIONS, DELAYS, CANCELLATIONS, DELIVERY
FAILURES, DATA LOSS, CONTENT CORRUPTION, PACKET
LOSS, OR OTHER DAMAGE RESULTING FROM ANY OF THE
FOREGOING. In addition, UBIQUITI NETWORKS does not
warrant that the operation of the Products will be errorfree or that operation will be uninterrupted. In no event
shall UBIQUITI NETWORKS be responsible for damages
or claims of any nature or description relating to system
performance, including coverage, buyer’s selection of
products (including the Products) for buyer’s application
and/or failure of products (including the Products) to meet
government or regulatory requirements.
43
Appendix D: Warranty
airFiber® X User Guide
Limitation of Liability
EXCEPT TO THE EXTENT PROHIBITED BY LOCAL LAW, IN NO
EVENT WILL UBIQUITI OR ITS SUBSIDIARIES, AFFILIATES OR
SUPPLIERS BE LIABLE FOR DIRECT, SPECIAL, INCIDENTAL,
CONSEQUENTIAL OR OTHER DAMAGES (INCLUDING LOST
PROFIT, LOST DATA, OR DOWNTIME COSTS), ARISING
OUT OF THE USE, INABILITY TO USE, OR THE RESULTS OF
USE OF THE PRODUCT, WHETHER BASED IN WARRANTY,
CONTRACT, TORT OR OTHER LEGAL THEORY, AND
WHETHER OR NOT ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES.
Note
Some countries, states and provinces do not allow
exclusions of implied warranties or conditions, so the
above exclusion may not apply to you. You may have
other rights that vary from country to country, state to
state, or province to province. Some countries, states
and provinces do not allow the exclusion or limitation of
liability for incidental or consequential damages, so the
above limitation may not apply to you. EXCEPT TO THE
EXTENT ALLOWED BY LOCAL LAW, THESE WARRANTY
TERMS DO NOT EXCLUDE, RESTRICT OR MODIFY, AND
ARE IN ADDITION TO, THE MANDATORY STATUTORY
RIGHTS APPLICABLE TO THE LICENSE OF ANY SOFTWARE
(EMBEDDED IN THE PRODUCT) TO YOU. The United
Nations Convention on Contracts for the International Sale
of Goods shall not apply to any transactions regarding the
sale of the Products.
44
Ubiquiti Networks, Inc.
airFiber® X User Guide
Appendix E: Compliance
Information
Installer Compliance Responsibility
Devices must be professionally installed and it is the
professional installer’s responsibility to make sure the
device is operated within local country regulatory
requirements.
airFiber AF-2X
FCC
Changes or modifications not expressly approved by the
party responsible for compliance could void the user’s
authority to operate the equipment.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions.
1. This device may not cause harmful interference, and
2. This device must accept any interference received,
including interference that may cause undesired
operation.
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in
a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV
technician for help.
Operations of this equipment in a residential area is likely
to cause harmful interference in which case the user will
be required to correct the interference at his own expense.
This radio transmitter (FCC: SWX-AF2X) has been approved
by FCC to operate with the antenna types listed below
with the maximum permissible gain and required antenna
impedance for each antenna type indicated. Antenna
types not included in this list, having a gain greater than
the maximum gain indicated for that type, are strictly
prohibited for use with this device.
Appendix E: Compliance Information
Industry Canada
CAN ICES-3(B)/NMB-3(B)
To reduce potential radio interference to other users, the
antenna type and its gain should be so chosen that the
equivalent isotropically radiated power (e.i.r.p.) is not more
than that permitted for successful communication.
This device complies with Industry Canada licence-exempt
RSS standard(s). Operation is subject to the following two
conditions:
1. This device may not cause interference, and
2. This device must accept any interference, including
interference that may cause undesired operation of the
device.
This radio transmitter (IC: 6545A-AF2X) has been approved
by Industry Canada to operate with the antenna types
listed below with the maximum permissible gain and
required antenna impedance for each antenna type
indicated. Antenna types not included in this list, having
a gain greater than the maximum gain indicated for that
type, are strictly prohibited for use with this device.
• Dish antenna, gain: 6 dBi
• Dish antenna, gain: 24 dBi
CAN ICES-3(B)/NMB-3(B)
Pour réduire le risque d’interférence aux autres utilisateurs,
le type d’antenne et son gain doivent être choisies de
façon que la puissance isotrope rayonnée équivalente
(PIRE) ne dépasse pas ce qui est nécessaire pour une
communication réussie.
Cet appareil est conforme à la norme RSS Industrie Canada
exempts de licence norme(s). Son fonctionnement est
soumis aux deux conditions suivantes:
1. Cet appareil ne peut pas provoquer d’interférences et
2. Cet appareil doit accepter toute interférence, y compris
les interférences qui peuvent causer un mauvais
fonctionnement du dispositif.
Cet émetteur radio (IC: 6545A-AF2X) a été approuvée par
Industrie Canada pour l’exploitation avec l’antenne types
énumérés ci-dessous avec le gain maximal admissible
et requis l’impédance de l’antenne pour chaque type
d’antenne indiqué. Types d’antenne non inclus dans cette
liste, ayant un gain supérieur au gain maximal indiqué
pour ce type, sont strictement interdits pour une utilisation
avec cet appareil. Immédiatement suite à la remarque, le
fabricant doit fournir une liste de tous les types d’antenne
approuvé pour une utilisation avec l’émetteur, ce qui
indique le gain maximal d’antenne permis (en dBi) et
requis d’impédance pour chacun.
• Antenne parabolique, gain: 6 dBi
• Antenne parabolique, gain: 24 dBi
• Dish antenna, gain: 6 dBi
• Dish antenna, gain: 24 dBi
Ubiquiti Networks, Inc.
45
Appendix E: Compliance Information
airFiber® X User Guide
RF Exposure Warning
airFiber AF-3X
The antennas used for this transmitter must be installed
to provide a separation distance of at least 97 cm from
all persons and must not be located or operating in
conjunction with any other antenna or transmitter.
FCC
Les antennes utilisées pour ce transmetteur doivent être
installé en considérant une distance de séparation de
toute personnes d’au moins 97 cm et ne doivent pas être
localisé ou utilisé en conflit avec tout autre antenne ou
transmetteur.
Australia and New Zealand
Warning: This is a Class B product. In a domestic
environment this product may cause radio interference
in which case the user may be required to take adequate
measures.
CE Marking
CE marking on this product represents the product is in
compliance with all directives that are applicable to it.
Changes or modifications not expressly approved by the
party responsible for compliance could void the user’s
authority to operate the equipment.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions.
1. This device may not cause harmful interference, and
2. This device must accept any interference received,
including interference that may cause undesired
operation.
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in
a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV
technician for help.
Operations of this equipment in a residential area is likely
to cause harmful interference in which case the user will
be required to correct the interference at his own expense.
This radio transmitter (FCC: SWX-AF3X) has been approved
by FCC to operate with the antenna types listed below
with the maximum permissible gain and required antenna
impedance for each antenna type indicated. Antenna
types not included in this list, having a gain greater than
the maximum gain indicated for that type, are strictly
prohibited for use with this device.
• Dish antenna, gain: 12 dBi
• Dish antenna, gain: 26 dBi
• Dish antenna, gain: 29 dBi
46
Ubiquiti Networks, Inc.
airFiber® X User Guide
Appendix E: Compliance Information
Industry Canada
RF Exposure Warning
CAN ICES-3(B)/NMB-3(B)
The antennas used for this transmitter must be installed
to provide a separation distance of at least 126 cm from
all persons and must not be located or operating in
conjunction with any other antenna or transmitter.
To reduce potential radio interference to other users, the
antenna type and its gain should be so chosen that the
equivalent isotropically radiated power (e.i.r.p.) is not more
than that permitted for successful communication.
This device complies with Industry Canada licence-exempt
RSS standard(s). Operation is subject to the following two
conditions:
1. This device may not cause interference, and
2. This device must accept any interference, including
interference that may cause undesired operation of the
device.
This radio transmitter (IC: 6545A-AF3X) has been approved
by Industry Canada to operate with the antenna types
listed below with the maximum permissible gain and
required antenna impedance for each antenna type
indicated. Antenna types not included in this list, having
a gain greater than the maximum gain indicated for that
type, are strictly prohibited for use with this device.
• Dish antenna, gain: 12 dBi
• Dish antenna, gain: 26 dBi
• Dish antenna, gain: 29 dBi
Les antennes utilisées pour ce transmetteur doivent être
installé en considérant une distance de séparation de
toute personnes d’au moins 126 cm et ne doivent pas être
localisé ou utilisé en conflit avec tout autre antenne ou
transmetteur.
Australia and New Zealand
Warning: This is a Class B product. In a domestic
environment this product may cause radio interference
in which case the user may be required to take adequate
measures.
CE Marking
CE marking on this product represents the product is in
compliance with all directives that are applicable to it.
CAN ICES-3(B)/NMB-3(B)
Pour réduire le risque d’interférence aux autres utilisateurs,
le type d’antenne et son gain doivent être choisies de
façon que la puissance isotrope rayonnée équivalente
(PIRE) ne dépasse pas ce qui est nécessaire pour une
communication réussie.
Cet appareil est conforme à la norme RSS Industrie Canada
exempts de licence norme(s). Son fonctionnement est
soumis aux deux conditions suivantes:
1. Cet appareil ne peut pas provoquer d’interférences et
2. Cet appareil doit accepter toute interférence, y compris
les interférences qui peuvent causer un mauvais
fonctionnement du dispositif.
Cet émetteur radio (IC: 6545A-AF3X) a été approuvée par
Industrie Canada pour l’exploitation avec l’antenne types
énumérés ci-dessous avec le gain maximal admissible
et requis l’impédance de l’antenne pour chaque type
d’antenne indiqué. Types d’antenne non inclus dans cette
liste, ayant un gain supérieur au gain maximal indiqué
pour ce type, sont strictement interdits pour une utilisation
avec cet appareil. Immédiatement suite à la remarque, le
fabricant doit fournir une liste de tous les types d’antenne
approuvé pour une utilisation avec l’émetteur, ce qui
indique le gain maximal d’antenne permis (en dBi) et
requis d’impédance pour chacun.
• Antenne parabolique, gain: 12 dBi
• Antenne parabolique, gain: 26 dBi
• Antenne parabolique, gain: 29 dBi
Ubiquiti Networks, Inc.
47
Appendix E: Compliance Information
airFiber® X User Guide
airFiber AF-5X
Industry Canada
FCC
CAN ICES-3(B)/NMB-3(B)
Changes or modifications not expressly approved by the
party responsible for compliance could void the user’s
authority to operate the equipment.
To reduce potential radio interference to other users, the
antenna type and its gain should be so chosen that the
equivalent isotropically radiated power (e.i.r.p.) is not more
than that permitted for successful communication.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions.
1. This device may not cause harmful interference, and
2. This device must accept any interference received,
including interference that may cause undesired
operation.
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in
a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV
technician for help.
Operations of this equipment in a residential area is likely
to cause harmful interference in which case the user will
be required to correct the interference at his own expense.
This radio transmitter (FCC: SWX-AF5X) has been approved
by FCC to operate with the antenna types listed below
with the maximum permissible gain and required antenna
impedance for each antenna type indicated. Antenna
types not included in this list, having a gain greater than
the maximum gain indicated for that type, are strictly
prohibited for use with this device.
• Dish antenna, gain: 23 dBi
• Dish antenna, gain: 30 dBi
• Dish antenna, gain: 34 dBi
DFS Regulatory Regions
Operation in DFS regulatory regions requires an antenna
with minimum gain of 23 dBi.
This device complies with Industry Canada licence-exempt
RSS standard(s). Operation is subject to the following two
conditions:
1. This device may not cause interference, and
2. This device must accept any interference, including
interference that may cause undesired operation of the
device.
This radio transmitter (IC: 6545A-AF5X) has been approved
by Industry Canada to operate with the antenna types
listed below with the maximum permissible gain and
required antenna impedance for each antenna type
indicated. Antenna types not included in this list, having
a gain greater than the maximum gain indicated for that
type, are strictly prohibited for use with this device.
• Dish antenna, gain: 23 dBi
• Dish antenna, gain: 30 dBi
• Dish antenna, gain: 34 dBi
CAN ICES-3(B)/NMB-3(B)
Pour réduire le risque d’interférence aux autres utilisateurs,
le type d’antenne et son gain doivent être choisies de
façon que la puissance isotrope rayonnée équivalente
(PIRE) ne dépasse pas ce qui est nécessaire pour une
communication réussie.
Cet appareil est conforme à la norme RSS Industrie Canada
exempts de licence norme(s). Son fonctionnement est
soumis aux deux conditions suivantes:
1. Cet appareil ne peut pas provoquer d’interférences et
2. Cet appareil doit accepter toute interférence, y compris
les interférences qui peuvent causer un mauvais
fonctionnement du dispositif.
Cet émetteur radio (IC: 6545A-AF5X) a été approuvée par
Industrie Canada pour l’exploitation avec l’antenne types
énumérés ci-dessous avec le gain maximal admissible
et requis l’impédance de l’antenne pour chaque type
d’antenne indiqué. Types d’antenne non inclus dans cette
liste, ayant un gain supérieur au gain maximal indiqué
pour ce type, sont strictement interdits pour une utilisation
avec cet appareil. Immédiatement suite à la remarque, le
fabricant doit fournir une liste de tous les types d’antenne
approuvé pour une utilisation avec l’émetteur, ce qui
indique le gain maximal d’antenne permis (en dBi) et
requis d’impédance pour chacun.
• Antenne parabolique, gain: 23 dBi
• Antenne parabolique, gain: 30 dBi
• Antenne parabolique, gain: 34 dBi
48
Ubiquiti Networks, Inc.
airFiber® X User Guide
Appendix E: Compliance Information
RF Exposure Warning
The antennas used for this transmitter must be installed
to provide a separation distance of at least 126 cm from
all persons and must not be located or operating in
conjunction with any other antenna or transmitter.
Les antennes utilisées pour ce transmetteur doivent être
installé en considérant une distance de séparation de
toute personnes d’au moins 126 cm et ne doivent pas être
localisé ou utilisé en conflit avec tout autre antenne ou
transmetteur.
Australia and New Zealand
Warning: This is a Class B product. In a domestic
environment this product may cause radio interference
in which case the user may be required to take adequate
measures.
CE Marking
CE marking on this product represents the product is in
compliance with all directives that are applicable to it.
Alert sign! follows CE marking
Alert sign must be indicated if a restriction on use applied
to the product and it must follow the CE marking.
Ubiquiti Networks, Inc.
49
Appendix E: Compliance Information
airFiber® X User Guide
Frequency Ranges and Power Levels per Country/Region
airFiber AF-2X
The product can be operated in the countries and regions listed in the following table, within the stated frequency ranges
and output power (EIRP) limits.
Each country has its own power level and frequency regulations. To ensure the product operates under the necessary
regulatory compliance rules, the country where the device will be used must be selected during installation. The frequency
settings and output power (EIRP) limits will be tuned according to the regulations of the selected country/region:
50
Country/Region
Frequency Range
(Band Edges in MHz)
Max. EIRP (dBm)
Argentina
2400-2483
36
Australia
2400-2483
36
Bahrain
2400-2483
36
Brazil
2400-2483
36
Canada
2400-2483
   36*
Chile
2400-2483
36
China
2400-2483
36
Colombia
2400-2483
36
Ecuador
2400-2483
36
Ghana
2400-2483
36
Guam
2400-2483
   36*
Hong Kong
2400-2483
36
Indonesia
2400-2483
36
India
2400-2483
36
Kenya
2400-2483
36
Korea Republic
2400-2483
36
Kyrgyzstan
2400-2483
Not applicable
Malaysia
2400-2483
36
Mexico
2400-2483
36
New Zealand
2400-2483
36
Nigeria
2400-2483
36
Peru
2400-2483
36
Philippines
2400-2483
36
Puerto Rico
(U.S. territory)
2400-2483
   36*
Singapore
2400-2483
36
South Africa
2400-2483
36
Taiwan
2400-2483
36
Tajikistan
2400-2483
Not applicable
Thailand
2400-2483
20
Turkmenistan
2400-2483
Not applicable
Uganda
2400-2483
Not applicable
United States
2400-2483
   36*
Uzbekistan
2400-2483
Not applicable
Venezuela
2400-2483
36
Ubiquiti Networks, Inc.
airFiber® X User Guide
Appendix E: Compliance Information
Country/Region
Frequency Range
(Band Edges in MHz)
Max. EIRP (dBm)
Virgin Islands
(U.S. territory)
2400-2483
   36*
Vietnam
2400-2483
36
* A higher EIRP is possible based on FCC Part 15 requirements of reduction of conducted power by 1 dBm per 3 dBi increase of antenna gain
beyond 6 dBi.
Ubiquiti Networks, Inc.
51
Appendix E: Compliance Information
airFiber® X User Guide
airFiber AF-3X
The product can be operated in the countries and regions listed in the following table, within the stated frequency ranges
and output power (EIRP) limits.
Each country has its own power level and frequency regulations. To ensure the product operates under the necessary
regulatory compliance rules, the country where the device will be used must be selected during installation. The frequency
settings and output power (EIRP) limits will be tuned according to the regulations of the selected country/region:
52
Country/Region
Frequency Range
(Band Edges in MHz)
Max. EIRP (dBm)
Austria
3410-3900
66
Belgium
3410-3900
66
Bulgaria
3410-3900
66
Canada
3450-3650
3650-3700
57
44
Croatia
3410-3900
66
Cyprus
3410-3900
66
Czech Republic
3410-3900
66
Denmark
3410-3900
66
Estonia
3410-3900
66
Finland
3410-3900
66
France
3410-3900
66
Germany
3410-3900
66
Greece
3410-3900
66
Guam
(U.S. territory)
3650-3700
44
Hungary
3410-3900
66
Ireland
3410-3900
66
Italy
3410-3900
66
Latvia
3410-3900
66
Lithuania
3410-3900
66
Malta
3410-3900
66
Netherlands
3410-3900
66
Poland
3410-3900
66
Portugal
3410-3900
66
Puerto Rico
(U.S. territory)
3650-3700
44
Romania
3410-3900
66
Slovakia
3410-3900
66
Spain
3410-3900
66
Sweden
3410-3900
66
United Kingdom
3410-3900
66
United States
3650-3700
44
Virgin Islands
(U.S. territory)
3650-3700
44
Ubiquiti Networks, Inc.
airFiber® X User Guide
Appendix E: Compliance Information
airFiber AF-5X
The product can be operated in the countries and regions listed in the following table, within the stated frequency ranges
and output power (EIRP) limits.
Each country has its own power level and frequency regulations. To ensure the product operates under the necessary
regulatory compliance rules, the country where the device will be used must be selected during installation. The frequency
settings and output power (EIRP) limits will be tuned according to the regulations of the selected country/region:
5.1 GHz
5.2 GHz
Country/Region
Frequency Range
(Band Edges in
MHz)
Max.
EIRP
(dBm)
Argentina
5150-5250
49
Frequency Range
(Band Edges in
MHz)
5.4 GHz
Max.
EIRP
(dBm)
5.8 GHz
Frequency Range
(Band Edges in
MHz)
Max.
EIRP
(dBm)
Frequency Range
(Band Edges in
MHz)
Max.
EIRP
(dBm)
5470-5725
30
5725-5850
36
5470-5600,
5650-5725
30
5725-5855
36
Bahrain
5735-5835
20
Barbados
5725-5850
36
Belize
5735-5835
30
Bolivia
5735-5835
30
5725-5850
53
5735-5835
20
5725-5850
60
5735-5835
20
5735-5835
30
5735-5835
30
5735-5835
30
5725-5795,
5815-5850
36
5735-5835
30
5735-5835
30
5735-5835
30
Australia
Brazil
5470-5725
30
Brunei
Darussalam
Canada
5250-5350
30
Chile
5250-5350
30
5470-5600,
5650-5725
30
China
Colombia
5250-5350
30
Costa Rica
Denmark
5470-5725
30
Dominican
Republic
Ecuador
5150-5250
49
5250-5350
30
El Salvador
Finland
5470-5725
30
5725-5795,
5815-5850
36
Germany
5470-5725
30
5755-5875
36
Greece
5470-5725
30
5725-5795
36
Grenada
5470-5725
30
5725-5850
36
5735-5835
30
Guatemala
Honduras
5470-5725
30
5725-5850
36
5470-5725
30
5725-5850
36
5470-5725
30
5725-5875
36
India
5825-5875
36
Iraq
5735-5835
36
5725-5875
33
5725-5850
36
5735-5835
30
Hong Kong
5250-5350
30
Iceland
Ireland
5470-5725
30
Italy
5470-5725
30
Jamaica
5470-5725
30
Kenya
Ubiquiti Networks, Inc.
5250-5350
30
53
Appendix E: Compliance Information
airFiber® X User Guide
5.1 GHz
Country/Region
Frequency Range
(Band Edges in
MHz)
5.2 GHz
Max.
EIRP
(dBm)
Frequency Range
(Band Edges in
MHz)
5.4 GHz
Max.
EIRP
(dBm)
Korea Republic
5.8 GHz
Frequency Range
(Band Edges in
MHz)
Max.
EIRP
(dBm)
Frequency Range
(Band Edges in
MHz)
Max.
EIRP
(dBm)
5490-5710
30
5735-5815
30
5735-5835
30
5725-5795,
5815-5875
36
5725-5850
36
Lebanon
Liechtenstein
5470-5725
30
Macau
Malaysia
5735-5835
30
Mexico
5150-5250
49
5250-5350
30
5735-5835
30
Morocco
5735-5835
20
Nepal
5735-5835
30
New Zealand
5470-5725
30
5725-5850
53
Norway
5470-5725
30
5725-5795,
5815-5850
53
Oman
5470-5725
30
5725-5850
36
Pakistan
5735-5835
30
Panama
5735-5835
30
Papua New
Guinea
5735-5835
30
Peru
5150-5250
49
5250-5350
30
5470-5725
30
5725-5850
36
Philippines
5150-5250
49
5250-5350
30
5470-5725
30
5725-5850
36
5470-5725
30
5725-5875
36
5470-5600,
5650-5725
30
5725-5850
60
5735-5835
30
5650-5950
53
5735-5835
30
Portugal
Puerto Rico
(U.S. territory)
5250-5350
30
Qatar
Russia
5150-5350
43
5470-5650
23
Singapore
South Africa
5470-5725
30
5725-5850
60
Spain
5470-5725
30
5725-5795,
5815-5855
36
Switzerland
5470-5725
30
5725-5795,
5815-5855
36
Taiwan
5250-5350
30
5490-5710
30
5735-5815
30
Thailand
5250-5350
30
5470-5725
30
5725-5850
36
Trinidad And
Tobago
5470-5725
30
5725-5850
36
United
Kingdom
5470-5725
30
5725-5790,
5815-5850
36
5470-5600,
5650-5725
30
5725-5850
60
Uruguay
5470-5725
30
5725-5850
36
Uzbekistan
5470-5725
30
5725-5850
36
5735-5835
30
United States
Venezuela
54
5150-5250
5150-5250
49
49
5250-5350
5250-5350
30
30
Ubiquiti Networks, Inc.
airFiber® X User Guide
Appendix E: Compliance Information
The following table lists the maximum transmit output power (EIRP) for the 5.1 GHz band.
5.1 GHz Band
Channel Bandwidth
10 MHz
20 MHz
30 MHz
40 MHz
50 MHz
Ubiquiti Networks, Inc.
Frequency Range
(Band Edges in MHz)
Maximum Transmit
Output Power (EIRP)
in dBm
5155-5175
39
5166-5186
44
5177-5250
49
5156-5180
37
5161-5185
39
5166-5209
44
5190-5250
49
5155-5192
37
5163-5202
39
5173-5211
44
5182-5250
49
5155-5204
37
5165-5219
39
5180-5228
44
5189-5250
49
5155-5214
37
5165-5233
39
5184-5242
44
5193-5250
49
55
Appendix E: Compliance Information
RoHS/WEEE Compliance Statement
English
European Directive 2002/96/EC requires that the
equipment bearing this symbol on the product and/
or its packaging must not be disposed of with unsorted
municipal waste. The symbol indicates that this product
should be disposed of separately from regular household
waste streams. It is your responsibility to dispose
of this and other electric and electronic equipment
via designated collection facilities appointed by the
government or local authorities. Correct disposal
and recycling will help prevent potential negative
consequences to the environment and human health. For
more detailed information about the disposal of your old
equipment, please contact your local authorities, waste
disposal service, or the shop where you purchased the
product.
Deutsch
Die Europäische Richtlinie 2002/96/EC verlangt, dass
technische Ausrüstung, die direkt am Gerät und/oder an
der Verpackung mit diesem Symbol versehen ist , nicht
zusammen mit unsortiertem Gemeindeabfall entsorgt
werden darf. Das Symbol weist darauf hin, dass das
Produkt von regulärem Haushaltmüll getrennt entsorgt
werden sollte. Es liegt in Ihrer Verantwortung, dieses Gerät
und andere elektrische und elektronische Geräte über die
dafür zuständigen und von der Regierung oder örtlichen
Behörden dazu bestimmten Sammelstellen zu entsorgen.
Ordnungsgemäßes Entsorgen und Recyceln trägt dazu
bei, potentielle negative Folgen für Umwelt und die
menschliche Gesundheit zu vermeiden. Wenn Sie weitere
Informationen zur Entsorgung Ihrer Altgeräte benötigen,
wenden Sie sich bitte an die örtlichen Behörden oder
städtischen Entsorgungsdienste oder an den Händler, bei
dem Sie das Produkt erworben haben.
56
airFiber® X User Guide
Español
La Directiva 2002/96/CE de la UE exige que los equipos
que lleven este símbolo en el propio aparato y/o en su
embalaje no deben eliminarse junto con otros residuos
urbanos no seleccionados. El símbolo indica que el
producto en cuestión debe separarse de los residuos
domésticos convencionales con vistas a su eliminación. Es
responsabilidad suya desechar este y cualesquiera otros
aparatos eléctricos y electrónicos a través de los puntos
de recogida que ponen a su disposición el gobierno y las
autoridades locales. Al desechar y reciclar correctamente
estos aparatos estará contribuyendo a evitar posibles
consecuencias negativas para el medio ambiente y la
salud de las personas. Si desea obtener información más
detallada sobre la eliminación segura de su aparato usado,
consulte a las autoridades locales, al servicio de recogida
y eliminación de residuos de su zona o pregunte en la
tienda donde adquirió el producto.
Français
La directive européenne 2002/96/CE exige que
l’équipement sur lequel est apposé ce symbole sur le
produit et/ou son emballage ne soit pas jeté avec les
autres ordures ménagères. Ce symbole indique que
le produit doit être éliminé dans un circuit distinct
de celui pour les déchets des ménages. Il est de votre
responsabilité de jeter ce matériel ainsi que tout autre
matériel électrique ou électronique par les moyens de
collecte indiqués par le gouvernement et les pouvoirs
publics des collectivités territoriales. L’élimination et le
recyclage en bonne et due forme ont pour but de lutter
contre l’impact néfaste potentiel de ce type de produits
sur l’environnement et la santé publique. Pour plus
d’informations sur le mode d’élimination de votre ancien
équipement, veuillez prendre contact avec les pouvoirs
publics locaux, le service de traitement des déchets, ou
l’endroit où vous avez acheté le produit.
Italiano
La direttiva europea 2002/96/EC richiede che le
apparecchiature contrassegnate con questo simbolo sul
prodotto e/o sull’imballaggio non siano smaltite insieme
ai rifiuti urbani non differenziati. Il simbolo indica che
questo prodotto non deve essere smaltito insieme ai
normali rifiuti domestici. È responsabilità del proprietario
smaltire sia questi prodotti sia le altre apparecchiature
elettriche ed elettroniche mediante le specifiche strutture
di raccolta indicate dal governo o dagli enti pubblici
locali. Il corretto smaltimento ed il riciclaggio aiuteranno
a prevenire conseguenze potenzialmente negative per
l’ambiente e per la salute dell’essere umano. Per ricevere
informazioni più dettagliate circa lo smaltimento delle
vecchie apparecchiature in Vostro possesso, Vi invitiamo
a contattare gli enti pubblici di competenza, il servizio di
smaltimento rifiuti o il negozio nel quale avete acquistato
il prodotto.
Ubiquiti Networks, Inc.
airFiber® X User Guide
Appendix F: Declaration of
Conformity
Česky
[Czech]
UBIQUITI NETWORKS tímto prohlašuje, že toto UBIQUITI
NETWORKS zařízení, je ve shod se základními požadavky a
dalšími příslušnými ustanoveními směrnice 1999/5/ES.
Dansk
[Danish]
Hermed, UBIQUITI NETWORKS, erklærer at denne UBIQUITI
NETWORKS enhed, er i overensstemmelse med de væsentlige
krav og øvrige relevante krav i direktiv 1999/5/EF.
Nederlands
[Dutch]
Hierbij verklaart UBIQUITI NETWORKS, dat deze UBIQUITI
NETWORKS apparaat, in overeenstemming is met de essentiële
eisen en de andere relevante bepalingen van richtlijn 1999/5/EC.
English
Hereby, UBIQUITI NETWORKS, declares that this UBIQUITI
NETWORKS device, is in compliance with the essential
requirements and other relevant provisions of Directive
1999/5/EC.
Eesti
[Estonian]
Käesolevaga UBIQUITI NETWORKS kinnitab, et antud UBIQUITI
NETWORKS seade, on vastavus olulistele nõuetele ja teistele
asjakohastele sätetele direktiivi 1999/5/EÜ.
Suomi
[Finnish]
Täten UBIQUITI NETWORKS vakuuttaa, että tämä UBIQUITI
NETWORKS laite, on yhdenmukainen olennaisten vaatimusten ja
muiden sitä koskevien direktiivin 1999/5/EY.
Français
[French]
Par la présente UBIQUITI NETWORKS déclare que l’appareil
UBIQUITI NETWORKS, est conforme aux exigences essentielles et
aux autres dispositions pertinentes de la directive 1999/5/CE.
Deutsch
[German]
Hiermit erklärt UBIQUITI NETWORKS, dass sich dieses UBIQUITI
NETWORKS Gerät, in Übereinstimmung mit den grundlegenden
Anforderungen und den anderen relevanten Vorschriften der
Richtlinie 1999/5/EG befindet.
Ελληνική
[Greek]
Δια του παρόντος, UBIQUITI NETWORKS, δηλώνει ότι αυτή η
συσκευή UBIQUITI NETWORKS, είναι σε συμμόρφωση με τις
βασικές απαιτήσεις και τις λοιπές σχετικές διατάξεις της οδηγίας
1995/5/ΕΚ.
Magyar
[Hungarian]
Ezennel UBIQUITI NETWORKS kijelenti, hogy ez a UBIQUITI
NETWORKS készülék megfelel az alapvető követelményeknek és
más vonatkozó 1999/5/EK irányelv rendelkezéseit.
Íslenska
[Icelandic]
Hér, UBIQUITI NETWORKS, því yfir að þetta UBIQUITI NETWORKS
tæki er í samræmi við grunnkröfur og önnur viðeigandi ákvæði
tilskipun 1999/5/EC.
Italiano
[Italian]
Con la presente, UBIQUITI NETWORKS, dichiara che questo
dispositivo UBIQUITI NETWORKS, è conforme ai requisiti
essenziali ed alle altre disposizioni pertinenti della direttiva
1999/5/CE.
Latviski
[Latvian]
Ar šo, UBIQUITI NETWORKS, deklarē, ka UBIQUITI NETWORKS
ierīce, ir saskaņā ar būtiskajām prasībām un citiem attiecīgiem
noteikumiem Direktīvā 1999/5/EK.
Lietuviškai
[Lithuanian]
UBIQUITI NETWORKS deklaruoja, kad šis UBIQUITI NETWORKS
įrenginys atitinka esminius reikalavimus ir kitas 1999/5/EB
Direktyvos nuostatas.
Malti
[Maltese]
Hawnhekk, UBIQUITI NETWORKS, tiddikjara li dan il-mezz
UBIQUITI NETWORKS huwa konformi mar-rekwiżiti essenzjali u
dispożizzjonijiet rilevanti oħrajn ta ‘Direttiva 1999/5/EC.
Norsk
[Norwegian]
Herved UBIQUITI NETWORKS, erklærer at denne UBIQUITI
NETWORKS enheten, er i samsvar med de grunnleggende
kravene og andre relevante bestemmelser i direktiv 1999/5/EF.
Slovensky
[Slovak]
Týmto UBIQUITI NETWORKS, prehlasuje, že toto UBIQUITI
NETWORKS zariadenie, je v súlade so základnými požiadavkami a
ďalšími relevantnými ustanoveniami smernice 1999/5/ES.
Svenska
[Swedish]
Härmed UBIQUITI NETWORKS, intygar att denna UBIQUITI
NETWORKS enhet är i överensstämmelse med de väsentliga
egenskapskrav och övriga relevanta bestämmelser som framgår
av direktiv 1999/5/EG.
Ubiquiti Networks, Inc.
Appendix F: Declaration of Conformity
Español
[Spanish]
Por medio de la presente UBIQUITI NETWORKS declara que este
dispositivo UBIQUITI NETWORKS, cumple con los requisitos
esenciales y cualesquiera otras disposiciones aplicables o
exigibles de la Directiva 1999/5/CE.
Polski
[Polish]
Niniejszym, Ubiquiti Networks, oświadcza, że ​​urządzenie
UBIQUITI NETWORKS, jest zgodny z zasadniczymi wymaganiami
oraz pozostałymi stosownymi postanowieniami Dyrektywy
1999/5/EC.
Português
[Portuguese]
UBIQUITI NETWORKS declara que este dispositivo UBIQUITI
NETWORKS, está conforme com os requisitos essenciais e outras
disposições da Directiva 1999/5/CE.
Română
[Romanian]
Prin prezenta, UBIQUITI NETWORKS declară că acest dispozitiv
UBIQUITI NETWORKS este în conformitate cu cerințele esențiale
și alte prevederi relevante ale Directivei 1999/5/CE.
57
Appendix G: Contact Information
airFiber® X User Guide
Appendix G: Contact
Information
Ubiquiti Networks Support
Ubiquiti Support Engineers are located around the world
and are dedicated to helping customers resolve software,
hardware compatibility, or field issues as quickly as
possible. We strive to respond to support inquiries within
a 24-hour period.
Ubiquiti Networks, Inc.
2580 Orchard Parkway
San Jose, CA 95131
www.ubnt.com
Online Resources
Support: support.ubnt.com
Community: community.ubnt.com
Downloads: downloads.ubnt.com
AI080615
58
Ubiquiti Networks, Inc.
www.ubnt.com
©2015 Ubiquiti Networks, Inc. All rights reserved. Ubiquiti, Ubiquiti Networks, the Ubiquiti U logo, the Ubiquiti beam logo, airFiber, airOS, RocketDish,
TOUGHCable, and xRT are trademarks or registered trademarks of Ubiquiti Networks, Inc. in the United States and in other countries. All other trademarks are
the property of their respective owners.
Source Exif Data: 
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Author                          : A Imaoka
Create Date                     : 2015:08:13 13:25:48-04:00
Modify Date                     : 2015:08:13 13:26:38-04:00
Has XFA                         : No
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Metadata Date                   : 2015:08:13 13:26:38-04:00
Creator Tool                    : Adobe InDesign CC 2015 (Macintosh)
Format                          : application/pdf
Title                           : airFiber X User Guide
Creator                         : A Imaoka
Document ID                     : uuid:db73d35e-49cc-4504-9d0e-4a8aa775fa68
Instance ID                     : uuid:f14c346e-0ca2-408e-b236-7eb29efa99c0
Producer                        : Adobe PDF Library 15.0
Page Count                      : 38
EXIF Metadata provided by EXIF.tools
FCC ID Filing: SWX-AF2X

Navigation menu