Uniform HE7620 802.11n 20HT WIFI modular User Manual

Uniform Industrial Corp. 802.11n 20HT WIFI modular Users Manual

Use manual Rev. 1

Modification History Date Revision Editor Comment 0.1 2014/10/15
Wi-Fi module Specification Product Name Wi-Fi module Model Number Home Extender Family Host interface Wifi, Fast Ethernet ,USB, I2c,SPI,UART Wireless LAN Band 2.4G ISM Channels USA and Canada: ch1~ch11 Standard 82.11 n 20HT TX power(high gain) 802.11n:17~19dbm RX sensitivity 802.11n:-61dbm Antenna gain 5dbi Wire LAN Fast Ethernet(10/100M) x2 Led indicator Wireless x1, Ethernet x2, power x1 Input power DC5V/2.1A Power consumption <15W Temperature Range Operating Temp:-10~60℃ Storage Temp:-10~65℃ Humidity Operation Humidity: 10~90% Non-condensing PCB Dimension 70x57.66mm Regulatory compliance FCC Detail description 1 Description 802.11n 20HT Wi-Fi Board, High Power High Gain 2 System CPU:580MHzMIPS®24KCPUcore/MT7620AFlash:16MBDDR2:64MBRTC:NORF:1T1R,802.11n 20HT,HighpowerEthernet:10/100MbpsFastethernet
3Function3.0FunctionBlock3.1Wi‐FispecComplianceIEEE802.11n20HT3.2EthernetComplianceIEEE802.3u3.4USBSupportUSB2.0host3.5I2cSupportstandardspeed(100kbps)3.6SPI3.7UARTCompatiblewithRS232
4 HWinterfaceInterfaceConnectorMT7620AFunctionPinWi‐FiSMAN/AN/AEthernetport0RJ45MDI_TN_P0 MDI_TP_P0 MDI_RN_P0 MDI_RP_P0 U17 U16 T15 U15 Ethernetport4RJ45MDI_RP_P0 MDI_TP_P4 MDI_RN_P4 MDI_RN_P4 M17 M16 N17 N16 USBMiniUSB UPHY0_PADM UPHY0_PADP C16 C17 UART0Pinheader1x4TXD RXD R12 P12 UART1Pinheader1x4TXD2 RXD2 P13 P14 I2CPinheader1x6I2C_SCLK I2C_SD U14 T14 SPI Pinheader1x6SPI_CS0 SPI_CLK SPI_MOSI SPI_MISO SPI_CS1 C7 D8 A8 C8 C9 ResetButtonTackswitchND_D0 P8 PowerJackMiniDCJackN/A N/AGPIOTestpointND_D3 ND_D4 U10 T9 
5PCBPlacementWarning: This device must be professionally installed. The intended use is generally not for the general public. It is generally for industry/commercial use. Installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. IMPORTANT NOTE: This module is intended for OEM integrator. The OEM integrator is still responsible for he FCC compliance requirement of the end product which integrates this module. USERS MANUAL OF THE END PRODUCT: In the users manual of the end product, the end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. If the size of the end product is smaller
than 8x10cm, then additional FCC part 15.19 statement is required to be available in the users manual: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. LABEL OF THE END PRODUCT: The final end product must be labeled in a visible area with the following " Contains TX FCC ID: TFJHE7620. If the size of the end product is larger than 8x10cm, then the following FCC part 15.19 statement has to also be available on the label: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. 

Navigation menu