Unitech Electronics PA600BTGP Wireless Data Collection Terminal User Manual PDA PA600 II UM EN

Unitech Electronics Co., Ltd. Wireless Data Collection Terminal PDA PA600 II UM EN

UserManual.wiki >

Unitech Electronics >

PA600BTGP User Manual >

User manual part 1 revise HTML Version

User manual part 1 revise

unitech

PA600 Phone Edition

User’s Manual

400646G Version 1.0

Preface

About This Manual

This manual explains how to install, operate and maintain the PA600 II Rugged Mobile

Computer.

No part of this publication may be reproduced or used in any form, or by any electrical

or mechanical means, without permission in writing from the manufacturer. This

includes electronic or mechanical means, such as photocopying, recording, or infor-

mation storage and retrieval systems. The material in this manual is subject to change

without notice.

unitech global website address: http:\\www.unitech-adc.com

Bluetooth is a registered trademark of Bluetooth SIG.

Microsoft, Windows and ActiveSync are either registered

trademarks or trademarks of Microsoft Corporation. Other

product names mentioned in this manual may be trademarks

or registered trademarks of their respective companies and

are hereby acknowledged.

unitech is a member of Oracle Embedded Software

Licensing Program.

Regulatory Compliance Statements

FCC Warning Statement

This equipment has been tested and found to comply with the limits for a Class B dig-

ital device, pursuant to part 15 of the FCC rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interfer-

ence to radio communications. However, there is no guarantee that interference will

not occur in a particular installation. If this equipment does cause harmful interference

to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

1. This equipment complies with FCC RF radiation exposure limits set forth for an

uncontrolled environment.

2. Any changes or modifications (including the antennas) made to this device that

are not expressly approved by the manufacturer may void the user’s authority

to operate the equipment.

FCC Label Statement

This device complies with part 15 of the FCC rules. Operation is subject to the follow-

ing two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including interference that

may cause undesired operation.

Canadian Compliance Statement

This Class B Digital apparatus meets all requirements of the Canadian Interference-

Causing Equipment Regulations.

Cet appareil numerique de la classe B respecte les exigences du Reglement sur le

material broilleur du Canada.

European Conformity Statement

Declaration of Conformity with Regard to the R&TTE 1999/5/EC and EMC 89/336/

EEC directives.

Taiwan NCC Warning Statement

國家通訊傳播委員會 (NCC) 低功率電波輻射性電機管理辦法 (930322)

根據 NCC 低功率管理辦法規定：

第十二條　經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不

得擅自變更頻率、加大功率或變更原設計之特性及功能。

第十四條　低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾

現象時，應立即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信法

規定作業之無線電通信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波

輻射性電機設備之干擾。

為減少電磁波影響，請妥適使用!

About This Manual

iii

Laser Information

The unitech PA600 II series is certified in the U.S. to conform to the requirements of

DHHS/CDRH 21CFR Subchapter J and to the requirements of IEC 825-1. Class II and

Class 2 products are not considered to be hazardous. The PA600 II series contains

internally a Visible Laser Diode (VLD) whose emissions do not exceed the maximum

limits as set forth in the above regulations. The scanner is designed so that there is no

human access to harmful laser light during normal operation, user maintenance or

during prescribed service operations.

The laser safety warning label required by the DHHS/IEC for the PA600 II series's

optional laser scanner module is located on the memory compartment cover, on the

back of the unit.

CAUTION! Use of controls or adjustments or performance of procedures other

than those specified herein may result in hazardous laser light. Use of

optical instruments with the scanner will increase eye hazard. Optical

instruments include binoculars, microscopes, and magnifying glasses.

This does not include eye glasses worn by the user.

Battery Notices

This unit is equipped with a battery pack and backup battery. Both batteries will dis-

charge after an extended period of not being used.

When both batteries are discharged, recharge the unit for 16 hours in order to fully

charge the main battery and backup battery. There are two ways to recharge PA600

II:

1. Plug the USB charging cable to the PA600 II and plug the 5V/3A AC-DC

adapter to the power jack of the USB charging cable.

2. Place the PA600 II into the docking station and plug the 5V/3A AC-DC adapter

to the power jack of the docking station.

For more details, refer to page 8, Charging the Battery.

If the main battery is removed, the backup battery ensures the data on SDRAM is safe

for up to 2 hours. To prevent data loss, do not leave the PA600 II uncharged with the

main battery removed for an extended period.

Battery charge notice

It is important to consider the environment temperature whenever you are charging

the Lithium-Ion battery pack. The process is most efficient at normal room tempera-

ture or slightly cooler. It is essential that you charge batteries within the stated range of

10°C to 45°C. Charging batteries outside of the specified range could damage the bat-

teries and shorten their charging life cycle.

Storage and safety notice

Although charged Lithium-Ion batteries may be left unused for several months, their

capacity may be depleted due to build up of internal resistance. If this happens they

will require recharging prior to use. Lithium-Ion batteries may be stored at tempera-

tures between -20°C to 60°C, however they may be depleted more rapidly at the high

end of this range. It is recommended to store batteries within normal room tempera-

ture.

Table of Contents

Preface

About This Manual i

Regulatory Compliance Statements ............................................................................. i

FCC Warning Statement.......................................................................................................... i

FCC Label Statement .............................................................................................................. ii

Canadian Compliance Statement ............................................................................................ ii

European Conformity Statement ............................................................................................. ii

Laser Information ................................................................................................................ iii

Battery Notices ..................................................................................................................... iii

Battery charge notice.............................................................................................................. iii

Storage and safety notice ....................................................................................................... iv

Chapter 1

Getting Started 1

Introducing the PA600 II ................................................................................................... 1

Features................................................................................................................................... 2

Package Contents ............................................................................................................... 3

A Tour of the PA600 II........................................................................................................ 3

Front Left View........................................................................................................................ 4

Back View ............................................................................................................................... 5

Getting Started...................................................................................................................... 6

Installing the Battery ............................................................................................................... 6

Charging the Battery............................................................................................................... 8

Charging the Battery using the USB Cable ....................................................................... 8

Charging the Battery with the Docking Station .................................................................. 9

Checking the Battery Status .............................................................................................. 9

Connecting the PA600 II to a PC.......................................................................................... 10

Turning the PA600 II on for the First Time............................................................................ 11

Powering On.................................................................................................................... 11

Calibrating the PA600 II Screen ...................................................................................... 12

Chapter 2

Using the Hardware 14

Keypads and Function Buttons ................................................................................... 14

Adjusting the Screen Brightness................................................................................ 16

Using the Stylus................................................................................................................. 16

Using the SD/MMC memory card ................................................................................ 17

Inserting a Storage Card ................................................................................................. 17

Removing a Storage Card ............................................................................................... 17

Using the Laser Scanner ................................................................................................ 18

Using the SIM Card ........................................................................................................... 19

Inserting the SIM Card..................................................................................................... 19

Using the Phone................................................................................................................. 20

Making a Call Using the Phone Keypad ............................................................................... 21

Using the Contact List........................................................................................................... 21

Using the Speed Dial ............................................................................................................ 22

Customizing the Phone Settings........................................................................................... 22

Chapter 3

Getting Connected 23

Establishing Device-PC Connection.......................................................................... 23

Installing Microsoft ActiveSync ............................................................................................. 23

Connecting the Device to Your Computer ............................................................................ 26

Synchronizing with Your Computer........................................................................... 27

Connection options ............................................................................................................... 27

USB Connection .............................................................................................................. 27

Bluetooth Connection ...................................................................................................... 27

GPRS Connection ........................................................................................................... 30

WiFi Connection .............................................................................................................. 31

Synchronizing Information ............................................................................................ 35

Synchronization Options....................................................................................................... 35

Using ActiveSync to Exchange Files ........................................................................ 35

Chapter 4

Barcode Scanner Programs 37

Scanner Setting.................................................................................................................. 37

Scan2Key .............................................................................................................................. 37

Barcode Symbologies........................................................................................................... 38

Chapter 5

Advanced Settings 39

Adjusting Settings............................................................................................................. 39

Checking the Main and Backup Battery Status..................................................... 40

Extending Battery Life..................................................................................................... 41

Changing the Automatic Power Settings .............................................................................. 41

Adjusting Backlight Setting ................................................................................................... 42

Viewing Flash Memory Files ......................................................................................... 43

Performing a hardware reset ........................................................................................ 44

Performing a Warm Boot ...................................................................................................... 44

Performing a Cold Boot ........................................................................................................ 45

Performing a Clean Boot ...................................................................................................... 46

Appendix

System Specifications 47

Chapter 1

Getting Started

Introducing the PA600 II

Thank you for purchasing the PA600 II Rugged Mobile Computer.

Your PA600 II was designed for users who need a compact and

durable PDA for data collection and real time transactions.

The PA600 II is a rugged, compact and lightweight palm-size com-

puter using the Windows Mobile 5.0 operating system, and incorpo-

rating an integral bar code scanning laser device, cell phone

function, color LCD with touchscreen, keypad, and wireless com-

munication capability. It provides users with a standard Windows-

based environment for customizing and operating the device.

To reduce TCO, the PA600 II is sealed to meet IP64 standards and

has undergone multiple drop tests to prevent downtime.

Chapter 1 Getting Started

Features

Powerful system

• Microsoft Windows MobileTM 5.0

operating system

• Intel PXA270 processor with speed

of up to 624 MHz

System memory

• 128 MB SDRAM

• 320 MB Flash ROM

Display

• 3.5-inch QVGA TFT-LCD with

touch screen and backlight

• 240 x 320 resolution

Barcode scanner

• Built-in laser scan engine

• Built-in vibrator for scanning indi-

cation

• Symbol SE950 support

• Unitech Hamster barcode decoder

Communication

• USB Host & Client

• Bluetooth 2.0 + EDR

(supports Bluetooth Printer,

Bluetooth Modem, Bluetooth

ActiveSync)

• eGPRS Siemens MC75 Radio

Module, quad-band GSM 850/900/

1800/1900 MHz

– EDGE Multislot Class 10

– GPRS Multislot Class 12

– GSM Release 99

Audio

•MIC

• Speaker

• Headset Connector

• Receiver

Wireless connectivity

• 802.11b/g with diversity antenna

• Bluetooth wireless technology

Expansion slot

• Secure Digital (SD) card slot (sup-

ports SDHC up to 4G)

Battery life

• Operation time: typical 5 hours

(with Wifi), average 9 hours (w/o

Wifi)

• Charging time: under 5 hours

• Embedded backup battery cell

User-friendly interface

• Quick launch hot keys for enabling

backlight, calibration, phone calls,

software keyboard, and other

device management tasks

• Trigger keys for barcode scanning

Chapter 1 Getting Started

Package Contents

After opening the box, ensure the following accessories for the PA600 II are present:

If anything is missing or appear damaged in any way, contact your dealer.

A Tour of the PA600 II

The following sections describe the main components and features of the PA600 II.

PA600 II Terminal AC Adapter with universal plugs

Battery Pack Stylus

USB Charging Cables CD-ROM Quick Reference

Guide

Chapter 1 Getting Started

Front Left View

No. Component Description

1. Status indicator Indicates the battery charging and barcode scanning status.

Green - Battery is fully charged, or barcode

scanning process is completed without error.

Red - Battery is charging, barcode scanner is fired/

activated.

Yellow - GPRS is on

Blue - Bluetooth is on

2. Left scanner

trigger button

Press to activate the barcode laser scanner.

3. Power button If the device is off, press this button to turn it on.

Alternatively, when the unit is on, this key must be

pressed and held down for about three seconds in

order to turn the device off.

4. Microphone Enables you to record voice audio.

5. Universal

connector

Connects your device to a USB charging/

communication cable. This USB cable connects to the

computer’s USB port and accepts the 5V AC adapter

to provide power to the PA600 II.

This unit can simultaneously recharge and perform an

ActiveSync operation. You can also use it to connect

peripheral hardware, such as a docking station, to your

device. This port can also support USB and RS232

hosting for devices such as a USB or RS232 scanner,

keyboard, or USB memory key.

6. Keypad Keypad interface for controlling the PA600 II. See Keypads

and Function Buttons on page 14 for more information.

7. LCD touch screen Displays the applications and data stored on your device. It

is touch-sensitive and responds to the stylus or finger.

8. Speaker Enables you to hear audio from the PA600 II.

Chapter 1 Getting Started

Back View

No. Component Description

9. Battery compartment Houses the removable and rechargeable 3.7 V,

2200 mAH battery pack

10. Battery compartment

release latch

Opens the battery compartment.

11. Reset button Press the end of the stylus into the button to

reset your device.

12. Handstrap Enables you to securely hold the PA600 II while

using it.

13. Speaker Enables you to hear audio from the PA600 II.

14. Stylus Enables you to interact with the operating system.

To use the stylus, remove it from its holder and

hold it the same way as you hold a pen or pencil.

15. Strap holder Attachment location for holding hand strap,

carrying strap, and stylus.

16. Memory card slot Accommodates Secure Digital (SD) memory

cards and can serve as an SDIO port.

17. Barcode scanner window Scan barcodes window where the laser pass

through.

Chapter 1 Getting Started

Getting Started

This section explains how to install and charge the battery, how to check battery sta-

tus, how to turn on the PA600 II, and how to calibrate the screen.

Installing the Battery

WARNING! There is a risk of fire and burns if the battery pack is handled improp-

erly. DO NOT disassemble, crush, puncture, short external contacts,

or dispose the battery pack in fire or water. DO NOT attempt to open

or service the battery pack. Dispose of used batteries according to

local recycling guidelines in your area.

A backup battery cell is embedded into your device to prevent data loss in instances

when the removable battery pack is removed or completely discharged. This backup

battery cell will keep the data and system setting for up to 6 hours if the main battery is

removed.

NOTE: To enable the internal battery cell to provide backup power supply,

charge your device with the main battery pack for at least 16 hours.

1. Open the battery compartment by pushing the latch in the direction of the arrow

and lifting up.

The battery compartment is displayed:

NOTE: The plastic battery tab makes it easy to remove the battery.

Compartment contacts

Plastic battery tab

Battery hook

Chapter 1 Getting Started

2. Locate the backup battery switch and turn it on.

3. Position the battery pack, making sure the battery contacts are aligned with the

contacts in the compartment and the battery is placed on top of the plastic tab,

as shown in the following illustration.

4. Slide the battery pack into the battery bay while simultaneously pulling the bat-

tery hook until the battery clicks into place.

5. Replace the battery compartment cover.

Backup battery

switch

Contacts

Plastic tab

Battery hook

Chapter 1 Getting Started

Charging the Battery

Before using the PA600 II for the first time, you need to charge it for about 16 hours.

After that, you can charge the PA600 II 4 hours to recharge the battery to full capacity.

Charge the PA600 II using the USB charging cable or the docking station.

CAUTION! Operating the PA600 II for the first time without the AC adapter, and

without fully charging the backup battery may result in loss of data

stored in RAM memory. When the main battery is removed, the

backup battery retains RAM data in memory for 2 hours, please

charge the battery for the period to avoid the data loss in RAM mem-

ory.

NOTE: Turn the backup battery switch on before charging the battery. Data you

entered may not be properly stored until the built-in backup battery has

been adequately charged.

Charging the Battery using the USB Cable

1. Press and hold the connector button on the USB charging cable and connect it

to the PA600 II (1).

2. Plug the AC adapter cable into the power jack on the USB charging cable (2).

3. Connect the AC adapter into an electrical outlet (3).

Chapter 1 Getting Started

Charging the Battery with the Docking Station

1. Plug the AC adapter cable into the power jack on the docking station, then con-

nect the AC adapter into an electrical outlet.

2. Slide the device into the docking station until it clicks

into place.

3. The connection is secure when the bottom edge of the

device is aligned with the docking station, and the LED

indicator on the device lights up red.

Checking the Battery Status

If the battery level becomes low in the course of normal use, a status icon appears on the

device screen indicating low or very low battery status. In both cases, perform an Active-

Sync operation to back up your data, then recharge your device as soon as possible.

If the battery level reaches low status, the device will enter a sleep mode and cannot

be powered up until the battery is charged. Windows Mobile 5.0 devices will retain

installed applications and data when the main battery is completely drained for

extended periods of time.e

LED Status

LED Meaning

PA600 II Solid Red Charging

Solid Green Charging complete

Docking

Station

Power LED Power is on

Charging LED: Charging (For spare battery only)

Sync LED Synchronization is taking place

Chapter 1 Getting Started

Connecting the PA600 II to a PC

Use the USB cable to connect the PA600 II to a PC, in order to use with ActiveSync.

1. Press and hold the connector button on the USB charging cable and connect it

to the PA600 II (1).

2. Plug the USB connector into the USB port on the PC and connect the AC

adapter into the USB connector (2).

3. Connect the AC adapter into an electrical outlet (3).

Chapter 1 Getting Started

Turning the PA600 II on for the First Time

After you have initially charged your device for about 16 hours, the device is ready to

be used. You can now start up your device where you’ll calibrate the display, learn

some basic stylus usage, and set up the system time zone, date and time.

Powering On

1. Turn on your device by pressing

the power button on the front panel.

NOTE: The PA600 II screen ships

with a protective plastic film.

You may remove this if

desired by peeling from one

corner. The screen will be

more susceptible to scratch-

ing without the film, but will be

more readable.

2. The unitech PA600 II welcome

screen appears for a moment fol-

lowed by the Windows Mobile

screen. FUNC

ESC ghi jkl mno

wxyz

ENTER

TAB

tuvpqrs

key

abc Rs def

ALPHA

Power Button

Chapter 1 Getting Started

Calibrating the PA600 II Screen

The calibrate screen automatically appears when the unit is powered-on for the first

time or after the system is reset.

To calibrate the screen at any time, follow these instructions.

1. Tap Start → Settings, and then switch to System tab.

2. Tap the Screen icon.

Press Func key and ESC key simultaneously.

The Screen Settings window appears.

This Window enables you to customize the screen

settings.

3. Tap Align Screen to calibrate the screen.

The align screen window appears.

4. Tap the cross hair firmly and accurately.

Chapter 1 Getting Started

The cross hair moves to the next location.

5. Continue tapping the cross hairs until the

screen has been calibrated.

Chapter 2

Using the Hardware

Keypads and Function Buttons

The keypad enables you to both enter information and interact with the PDA operating

system and also operate secondary functions using the function button. When the

green function button is pressed, the green icon functions on the keypad become

available.

When the Function button is pressed,

an icon appears in the operating system:

The following table describes the keypad keys.

Key Main Function Secondary Function

Talk/Send Opens Phone screen to make a

call or send a message

—Enables/ disables secondary

function keys

Alpha —

End Exits Phone screen or ends a call

Turns the PA600 II on and off. —

Function activated icon

Chapter 2 Using the Hardware

Number 1 Left soft key - activates function

above in LCD screen.

Alphanumeric 2, a, b, c Up navigation key

Alphanumeric 3, d, e, f Right soft key - activates function

above in LCD screen.

Tab Windows key opens Start menu

Back space Escape key

Alphanumeric 4, g, h, i Left navigation key

Alphanumeric 5, j, k, l —

Alphanumeric 6, m, n, o Right navigation key

Alphanumeric 7, p, q, r, s Decreases screen brightness

Alphanumeric 8, t, u, v Down navigation key

Alphanumeric 9, w, x, y, z Increases screen brightness

Asterisk Illuminates keypad

Number 0, space —

Period Pound

Enter key OK

Key Main Function Secondary Function

Chapter 2 Using the Hardware

Adjusting the Screen Brightness

Adjust the screen brightness by pressing

the Function button to enable the soft

keys and pressing the 7 (decrease bright-

ness) or 9 (increase brightness) buttons.

Using the Stylus

CAUTION! Never use anything other than the PA600 II stylus on the screen. Oth-

erwise this could cause a permanent damage.

1. Remove the stylus from its holder.

2. Hold the stylus as you hold a pencil.

3. To make a choice from a menu, lightly tap the tip of the stylus on that choice.

4. To write data into a field on a form, use the stylus to print the letters or numbers.

Use very light pressure.

FUNC

ESC ghi jkl mno

wxyz

ENTER

TAB

tuvpqrs

key

abc Rs def

ALPHA

Function

Button

Increase

Brightness

Decrease

Brightness

Chapter 2 Using the Hardware

Using the SD/MMC memory card

Your device has an expansion slot compatible with a range of SD and MMC storage

cards, which are primarily used to back up or transfer files and data. The slot also sup-

ports SDIO cards for added connectivity options.

Inserting a Storage Card

1. Remove the four screws from the SD compartment cover and remove the

cover.

2. Insert the SD card with the notched corner as shown by the icon on the case.

3. Replace the SD compartment cover and the four compartment screws.

Removing a Storage Card

1. Remove the four screws from the SD compartment cover and remove the

cover.

2. Press the card in and release.

The card pops out.

3. Remove the card from the slot.

Chapter 2 Using the Hardware

Using the Laser Scanner

The PA600 II has an integrated laser scanner which reads all major bar code labels

with excellent performance.

NOTE: Scanning software must be enabled in order to operate the scanner.

This can be a user-loaded application or a pre-loaded utility such as

Scanner Setting and Scan2Key.

Activate the laser scanner by pressing either one

of the trigger keys located on the left and right side

of the unit.

The PA600 II has a built-in Scanner Setting utility

that allows you to test the device’s barcode scan

function.

1. To launch Scanner Settings, tap Start →

Settings, and then switch to System tab.

Tab the Scanner icon.

2. The Scanner Control Panel opens.

From here you can configure barcode scanner parameters such as enabling or

disabling barcode symbologies, setting data transmission options, configuring

magnetic and proximity reading options, and setting power management

options.

Scan button

Chapter 2 Using the Hardware

3. To test the barcode scanner, tap the Test

tab.

4. Tap Tools

5. Tap Enable Scan

6. To perform auto scan, Tap Tools → Auto

Scan → Start Auto- Scan

7. Choose Interval: 3 secs

8. Tap: Start

9. Laser scans every 3 seconds and barcode

is scanned automatically.

10. Tap Tools → Auto-Scan → Stop Auto-

Scan.

Using the SIM Card

The PA600 II has a slot for GPRS SIM card. It is placed inside the battery compart-

ment.

Inserting the SIM Card

1. Take out the battery cover and the main battery. Insert the SIM card with the

notched corner as shown in the picture below.

NOTE: The chip of the SIM card should face upwards.

2. Push the SIM card to the end until you hear a click. Push the lock to the right to

lock the card by stylus.

Chapter 2 Using the Hardware

Using the Phone

The PA600 II has an integrated phone keypad, which allows you to make, receive,

and send messages via the built-in module.

NOTE: Make sure you insert the SIM card properly.

To open the Phone screen, do one of the following.

1. Tap Phone on the bottom left corner of the screen.

2. Press Talk/Send button.

Press End button when you want to exit the Phone screen.

The Phone screen opens. From here you can manage the contact list, create speed

dials, messages, notes, and customize phone settings.

NOTE: If you SIM card is protected by a PIN code, input the password before

you can use the phone.

Tap the antenna signal icon on the upper right corner of the screen. Tap Wireless

Manager and turn on phone function.

Signal Description

Phone service searching

No signal is available.

Strongest signal strength

More bars you have, the

stronger signal you have.

No phone service provided.

Phone function is turned off.

Tap the antenna signal icon

and turn on phone function in

the Wireless Manager.

FUNC

ESC ghi jkl mno

wxyz

ENTER

TAB

tuvpqrs

key

abc Rs def

ALPHA

Talk/Send

button

End

button

Phone

keypad

Antenna signal icon

Chapter 2 Using the Hardware

Tap the speaker icon on the upper right corner of

the screen. You can adjust the device/ phone vol-

ume by moving the sliders and change the ring

volume by tapping On, Vibrate, or Off.

Making a Call Using the Phone Keypad

1. Tap Phone or press Talk/Send button.

2. Enter the desired phone numbers.

3. Tap the Talk button on the Phone screen.

4. When the call connects, you can tap Hold

to place the first number on hold.

5. Enter the second phone numbers and tap

Talk again.

6. Tap Swap to switch between calls.

7. Tap End or press End button to stop dialing

or end the call.

Using the Contact List

1. Tap Contacts on the bottom left corner of

the Phone screen.

2. Tap New on the bottom left corner of the

contact list, you can add a new contact.

3. Tap a contact, you can edit the contact info.

4. Tap and hold on a contact, a menu

appears. You can send e-mail/ text mes-

sage to the contact, add this contact to

speed dial list, and so on.

Speaker icon

Chapter 2 Using the Hardware

Using the Speed Dial

1. Tap Speed Dial on the Phone keypad.

2. Tap Menu, and select New.

3. Select a contact in your contact list by tap-

ping the desired contact.

4. Assign an available location for the new

speed dial entry. Tap OK, and then OK to

exit the speed dial list.

NOTE: The first speed dial location is

reserved for voice mail.

To make speed dial call, do one of the following.

1. Tap and hold the speed dial location

number assigned to a contact on the

Phone keypad.

2. Tap Speed Dial on the Phone keypad,

and tap the location number of the

desired speed dial entry.

Customizing the Phone Settings

Tap Menu, and select Options, you can change the default phone settings, including

ring sound, keypad sound, call barring, call forwarding, call waiting, mobile phone net-

work, etc.

Location

number

Chapter 3

Getting Connected

Establishing Device-PC Connection

Installing Microsoft ActiveSync

In order to exchange data between your computer and PA600 II, Microsoft ActiveSync

must be installed on your computer. Use the USB charging cable that comes with your

device to connect the device to your computer.

NOTE: If you have a previous version of the Microsoft ActiveSync installed in

your computer, uninstall it first before installing the latest version of

Microsoft ActiveSync.

To install Microsoft ActiveSync on your computer:

1. Close any open programs, including those that run at startup, and disable any

virus-scanning software.

2. Download the ActiveSync software from the Microsoft ActiveSync Download

page at

http://www.microsoft.com/windowsmobile/downloads/activesync42.mspx.

3. Browse the location of the downloaded file, and double-click it.

The installation wizard begins.

Chapter 3 Getting Connected

4. Click Next.

You are prompted to read the End User License Agreement (EULA).

5. Accept the license agreement terms and click Next.

You are prompted for user information.

6. Type the user name and organization and click Next.

You are prompted for the destination folder.

Chapter 3 Getting Connected

7. Select a drive to install the program and click Next.

The installation wizard has gathered the information it needs to install Active-

Sync and prompts you to begin the installation.

8. Click Install.

The program begin the installation

After the program has finished installing you see the following screen.

Unitech Electronics PA600BTGP Wireless Data Collection Terminal User Manual PDA PA600 II UM EN

Unitech Electronics Co., Ltd. Wireless Data Collection Terminal PDA PA600 II UM EN

Contents

User manual part 1 revise

Navigation menu

Namespaces

Views

Navigation