Universal Electronics 4012 ViewSonic Tweety RF Remote Control User Manual users manual

Universal Electronics Inc ViewSonic Tweety RF Remote Control users manual

users manual

Download:
Mirror Download [FCC.gov]
Document ID	224896
Application ID	kqE1+m+OryJPRjQFVtkS8w==
Document Description	users manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	57.84kB (723013 bits)
Date Submitted	2002-02-06 00:00:00
Date Available	2002-02-05 00:00:00
Creation Date	2001-12-10 07:52:12
Producing Software	Acrobat Distiller 5.0 (Windows)
Document Lastmod	2001-12-13 10:31:14
Document Title	Microsoft Word - ViewSonic Tweety RF RemoteRev2.91-QuieTek
Document Creator	ADOBEPS4.DRV Version 4.50
Document Author:	kim

P u t t in g You in Con t r ol of Tod ay 's Tech n ology
ViewSonic Tweety RF Remote
Product Specification
Work Order: 50-954
November 05, 2001
Rev. 2.9A
URCs: 4012B00
Author: Jason Etter
Viewsonic Tweety RF Remote
Universal Electronics Inc. Confidential
Rev 2.9A
November 05, 2001
Page 1 of 63
Revision History
Product Revision History
Specification
Rev
Date
12/6/00
12/20/00
01/12/01
02/05/01
02/13/01
Software
Ver Date
Sect.
1.1
3.2.4
3.3.2
3.3.3
6.1.2
6.1.6
7.4
1.0
6.2
ALL
3.3.2,
3.2.4,
3.2.5
1.1
3.1.1
3.1.2
3.1.3
3.2.4
3.3.1
3.3.2
3.3.3
3.3.5
7.4
8.6
Rev1.0
Rev 1.1
1.1
3.2.1/2
3.2.4
3.3
3.3.1
3.3.3
3.3.5
3.3.9
7.4
10.1
Viewsonic Tweety RF Remote
Universal Electronics Inc. Confidential
Update Description
By
Initial Draft
Added Network Description
Added Make and Break data for MUTE
Revised ID Setup
Revised RF Channel Change
Added table on RF Transmission
Added Hardware Interface Table
Revised RF Channel Frequency table and added frequency control
information.
Revised UEI key Data Packet information
Added Serial Input Timing Diagram
Added Battery life information and table
Changed Part Number reflect SOP package
Changed Varapoint Data to reflect the Data in section 6.0
Per new NMB Specification and Bill Browns Comments
Programming Instructions per Anthony’s request
Added these sections per Anthony’s request.
Updated IC package and part number, added comment on polydome keys.
Updated IC Package Type
Referenced spec section for Mfg. Reset, SETUP, and Stuck Key
Time-out, removed visible LED for SW only to No visible LED
Changed from double sided PCB to single sided PCB and added
comment on Gold Flash required for Varapoint
JE
JE
JE
JE
JE
Revised Key chart to match actual key labels.
Revised Stuck Key Time-out and added diagram for STUCK KEY
data packet to be sent out to HOST and added diagram for IDLE
MODE (SLEEP) data packet to be sent out to HOST
Revised ID Setup
Revised RF SETUP procedure
Added Factory Test mode for RF Channel Test
Added comment on packet data to be sent two times for all key
presses to end of this section.
Revised Battery Life Section per Bill Brown
Added Color and Printing specification
Kicked-off Specification
Revised IC from DIE package to QFP
Changed Target Device from TV to Viewsonic
Updated Key Table
Updated Definitions in regards to LED blinking methodology
Updated Stuck Key, sleep and Keep alive information and appendix
Updated RF Channel Change section
Updated Factory Test
Updated Low Battery section for the 6volt design
Changed data rate from max. 19.2 bps to fixed 9600 bps
Updated Data Packet and Pointing device information
Added statement on the each key press is calculates @ 1 second
Changed Low non operating range from –20 C to -10C
Rev 2.9A
November 05, 2001
Page 3 of 63
JE
JE
Rev 2.0
3.1.1
3.3
3.1.3
3.1.4
3.1.5
3.4
1.1, 4,
6.1.1
4.1
Rev 2.1
2.2
5.1.1
5.1.2
5.1.3
2.1.1
3.1.5
3.1.6
10.2
2.3
2.4
2.5
2.6
3.4 &
3.4.7.1
3.4.6.1
5.1.2
5.1.2
7.6
11
3.2.4,
3.4.6.2
3.4
3.4.3
3.4.5
4.12
2.7
3.2.4,
3.4.6.2,
7.6
11
2.8
2.9
11
3.2.4,
3.4.6.2
3.4
2.91
1.1
4.9
Viewsonic Tweety RF Remote
Universal Electronics Inc. Confidential
Changed IC package to QFP (from DIE)
Changed MUTE to RESYN in “Conventions and Notations”
Changed PCB material from FR4 to Paper Phenolic
Item 14- Added URC number
Item 3- No FCC testing by UEI
Revised “Remote UEI Key and Pointing Device Data Packet”
Changed RF Operating Band range to 2446.7 – 2464.3MHz
Table 2, Rqmt No. 4.10 – Changed to “Simplex”
Added Manchester Data Coding table
Revised RF Channel and Operating Bands
Revised RF Channels and Frequencies
Added Pulse Width Timing section
Added comment that NMB receiver Spec 0.9 takes precedence
Modified item 3 to state FCC certification will be done by Optoma
with UEI for support only.
Item 1 (Batteries Included) has been changed from No to Yes-Bulk
Item 2 (Batter Cover) Rating Label required has been changed from
No to yes installed in specified area.
Item 10 Device Label in addition to packaging changed from Yes
to Installed on Unit
Changed FCC requirement to read as follows “Optoma will certify
the complete unit with remote and keyboard.
With documentation and possible engineering support to Optoma
from UEI.
Added provision to allow for using the varapoint mouse and the left
and Right select keys simultaneously
Lee
JE
JE
JE
Add notes on power state for entering Factory Test modes and E2
Revised RF Channels and Frequencies
Revised RF Channel Data to match the transmission table
Updated Color Specification Chart
Imported revised rendering dated 8/15/01 Style A rev 3.0
Updated Key charts for Smart and Enter Key
JE
JE
Added Definition for Mouse Right and Left while used in conjunction
with the mouse
Updated Device Number Setup definition
Updated E2 Initializtion Definition
Changed power source from 2.2VDC to 2.2VDC
JE
JE
Updated key-tables to reflect silk-screening changes
Updated Rendering imported with silk-screening changes
Updated Rendering with new Vara-touch pointer
Added Break Data ‘F6’ for the Sync Key
Added Break Data ‘F6’ for the Sync Key
Revised Comment in Re-Sync Section in regards to no Break-Code
being sent after the Re-Sync key was released.
Corrected Frequency
Output power is –18dbm
Rev 2.9A
November 05, 2001
Page 4 of 63
JE
JE
RM
Approvals:
Jerry Bardin
VP, Engineering (UEI)
Date:
Jakob Kishon
Viewsonic
Steve Gates
Sr.Director of Production Engineering
Development (UEI)
Date:
Dave Schafer
D2M
Ken Sweeney
Director of OEM Sales-West (UEI)
Date:
Mike Zapka
ViewSonic
Huyen Phan
Manager, SQA (UEI)
Date:
Rich Acosta
NMB RF Receiver Group
Jay Conway
Director, Library Technology (UEI)
Date:
John Gou
Manager/NMB RF Receiver
Group
Anthony Phan,
Manager, Software
Date:
Jason Etter
Sales Applications Engineering (UEI)
Viewsonic Tweety RF Remote
Universal Electronics Inc. Confidential
Rev 2.9A
November 05, 2001
Page 5 of 63
Table of Contents
Product Revision History ...........................................................................................................................................................................3
Purpose and Scope .....................................................................................................................................................................8
1.1
1.2
Description.................................................................................................................................. 8
Project Type ................................................................................................................................ 8
Applicable Documents ..............................................................................................................................................................8
2.1 Project Documentation ........................................................................................................... 8
2.1.1 Customer Specification ............................................................................................... 9
2.1.2 Other Product Documentation ................................................................................. 9
2.2 UEI Standard Documentation .............................................................................................. 9
2.2.1 UEI Standard Glossary.................................................................................................. 9
2.2.2 UEI Standard Hardware General Information .................................................... 9
2.2.3 UEI Standard Operational Features Descriptions ............................................ 9
2.2.4 UEI Standard Testing Procedures............................................................................ 9
Functional Requirements .......................................................................................................................................................9
3.1 Product Summary..................................................................................................................... 9
3.1.1 General Information ...................................................................................................... 9
3.1.2 Software Information.................................................................................................... 9
3.1.3 Hardware Information .................................................................................................11
3.1.4 Mechanical Information .............................................................................................12
3.1.5 Quality/ Testing Information...................................................................................12
3.1.6 Miscellaneous Information........................................................................................13
3.2 Product Library.........................................................................................................................13
3.2.1 Target Device Mode Mapping ...................................................................................13
3.2.2 Defaults..............................................................................................................................13
3.2.3 Library Upgrade Support ............................................................................................13
3.2.4
Key Table .............................................................................................................................14
3.3
Operational Features......................................................................................................................15
3.4
Remote UEI Key and Pointing Device Data Packet......................................................................16
3.4.1
Definitions ............................................................................................................................20
3.4.2
Time Event / Data Packet Transmission Diagram............................................................23
Some notations used in the Time Event / Data Packet Diagram .....................................................27
Notation 27
Function Description ...........................................................................................................................27
Make ...........................................................................................................................................................................................................27
3.4.3
3.4.4
3.4.5
3.4.6
3.4.7
3.4.8
RF Transmission General Specification .......................................................................................................................................39
4.1
Device Number Setup ..........................................................................................................28
RF Channel Change ............................................................................................................29
E2 Initialization....................................................................................................................31
Factory Test Mode(s)...........................................................................................................32
Key Test (Also used in Factory Test for Key): ..................................................................33
Low Battery Indicator.........................................................................................................38
Data Coding...................................................................................................................................40
Hardware Interface.........................................................................................................................................................................41
5.1
Transmitter Outline /Interface .......................................................................................................41
5.1
Product Performance Requirements ..............................................................................................43
5.1.1
RF CHANNEL and OPERATING BANDS ......................................................................43
5.1.2
RF Channels and Frequencies ............................................................................................43
5.1.3
RF Channel Operation Range ............................................................................................44
5.1.4
RF Modulation Scheme and Modulation Level ................................................................44
5.1.5
Maximum Bit Rate ..............................................................................................................44
5.1.6
RF Power Management.......................................................................................................44
•
T2 = Frequency Stable Time. Typically, it should be T2 > 20ms ............................................44
5.1.7
Transmitter Data Input Level ............................................................................................44
The transmitter data input level should be fixed as the supply voltage drops when using battery.
It is required that the Input level will be Vp-p = 100mv (+/- 10%).................................................44
Viewsonic Tweety RF Remote
Universal Electronics Inc. Confidential
Rev 2.9A
November 05, 2001
Page 6 of 63
5.1.8
Communication Link...........................................................................................................44
Electrical Requirements .................................................................................................................................................................46
6.1
Power.............................................................................................................................................46
6.2
Visible LEDs .................................................................................................................................46
NA .............................................................................................................................................................46
6.3
Transmission IC.............................................................................................................................46
6.4
Battery Life....................................................................................................................................46
6.5
Range.............................................................................................................................................46
Mechanical Requirements..............................................................................................................................................................47
7.1.1
HRC Assembly.....................................................................................................................47
7.1.2
Assembly LED’s...................................................................................................................47
7.2
Enclosure .......................................................................................................................................47
7.2.1
Enclosure and Battery Cover Shape ..................................................................................47
7.2.2
Material ................................................................................................................................47
7.2.3
Texture..................................................................................................................................48
7.2.4
Color .....................................................................................................................................48
7.3
Keypad with Polydome .................................................................................................................48
7.3.1
Material ................................................................................................................................48
7.3.2
Tactile Feel ...........................................................................................................................48
7.3.3
Force Vs. Travel...................................................................................................................49
7.3.4
Life ........................................................................................................................................50
7.3.5
Keypad Pull-out Force ........................................................................................................50
7.3.6
Key stick and key stuck.......................................................................................................50
7.4
PCB Material .................................................................................................................................50
7.5
Battery Compartment ....................................................................................................................50
7.6
Printing ..........................................................................................................................................50
7.7
Labeling.........................................................................................................................................52
7.7.1
Date Code .............................................................................................................................52
7.7.2
Part Number Label..............................................................................................................52
7.7.3
Country of Origin ................................................................................................................52
QUALITY ........................................................................................................................................................................................53
8.1
Appearance ....................................................................................................................................53
8.2
Cosmetic ........................................................................................................................................53
8.2.1
Evaluation Criteria..............................................................................................................53
8.2.2
Definition of Flaw and Defect .............................................................................................54
8.2.3
Definition of Classes ............................................................................................................54
8.2.4
Cosmetic Evaluation............................................................................................................55
8.3
Durability Testing..........................................................................................................................56
8.3.1
Structure and Strength........................................................................................................56
8.3.2
Printing.................................................................................................................................56
8.3.3
Battery Contact....................................................................................................................57
8.3.4
Painting wear test (if necessary) .........................................................................................57
8.3.5
Rubber coating wear test (if necessary) .............................................................................57
8.3.6
Epoxy key test ......................................................................................................................57
ENVIRONMENTAL & SHOCK REQUIREMENTS ................................................................................................................59
9.1
9.2
9.3
9.4
9.5
9.6
9.7
9.8
10
Standard Compliances...............................................................................................................................................................62
10.1
10.2
11
Temperature...................................................................................................................................59
Humidity Test................................................................................................................................59
Low Temperature Test...................................................................................................................59
High Temperature Test..................................................................................................................59
Thermal Shock...............................................................................................................................60
Drop Test .......................................................................................................................................60
Solvent Resistance.........................................................................................................................61
Liquid Spill....................................................................................................................................61
ESD Protection ..............................................................................................................................62
FCC ...............................................................................................................................................62
Rendering....................................................................................................................................................................................63
Viewsonic Tweety RF Remote
Universal Electronics Inc. Confidential
Rev 2.9A
November 05, 2001
Page 7 of 63
Purpose and Scope
1.1 Description
The Viewsonic-Tweety remote will be a dedicated 2.4 gHz RF remote with 10 channel capability.
This will be a 6V product and will use 4 AAA batteries. It will use a Samsung 16K
(S3P/C80F9XFE-QZR5) (QFP) Micro-controller.
Network Description:
The RF modules support up to 10 channels in the ISM band of 2446.7MHz to 2464.3MHz,
providing a form of frequency division multiple access (FDMA). This enables the simple
implementation of systems requiring multiple devices to be operating continuously and
concurrently.
Note: This document contains all functional specifications and testing/quality requirements
that UEI will perform. By signing off on this document, the customer agrees that these
product/project parameters are final. Any further revisions will be accompanied by
Engineering Change Request and appropriate authorizations.
Features
•
•
•
•
•
•
•
•
Samsung 16K(QFP)
E2 (128 byte) –To save RF Channel Data and Device ID
34 keys
6V product (4 AAA)
Varapoint
W-Link 2.4 gHz RF transmitter
Slide Door
Poly Dome Keys
1.2 Project Type
OEM-West
Applicable Documents
Appendix A: NMB/UEI Remote Devices and Receiver Module Rev. 0.1
Appendix B: NMB RF-Receiver (UART) and HOST (Image Processor)
2.1
Project Documentation
The following documents of exact issue and date form part of this specification:
Viewsonic Tweety RF Remote
Universal Electronics Inc. Confidential
Rev 2.9A
November 05, 2001
Page 8 of 63
2.1.1 Customer Specification
NMB RF-Receiver and Host Image Processor rev 0.9
(This spec takes precedence a changes to the receiver software must also be made to
the remote and keyboard)
2.1.2 Other Product Documentation
N/A
2.2
UEI Standard Documentation
UEI SPEC 0020, UEI SPEC HE003, UEI SPEC 0002
2.2.1 UEI Standard Glossary
N/A
2.2.2 UEI Standard Hardware General Information
Refer to Section 3.1.3
2.2.3 UEI Standard Operational Features Descriptions
2.2.4 UEI Standard Testing Procedures
Refer to Section 6.0, Section 7.0 and Section 9.0.
3 Functional Requirements
3.1 Product Summary
3.1.1 General Information
Functional Keychart Included
IC Type and size and package type
Keypad Parameters Specified
Mode Indicator LEDs
Multiple Devices (Jumpers)
OTPs Used for initial Production
Product Development Type:
OFA, OEM, Private Label, Cable, Chip Only
Request Load Included
Upgradeable Product (E2)
Yes
Samsung (16K)
(QFP)
Yes
No
No
Yes
OEM-West
NA
NA
3.1.2 Software Information
Channel Scan
Channel +/- Simulation w/Lock Option
Viewsonic Tweety RF Remote
Universal Electronics Inc. Confidential
No
No
Rev 2.9A
November 05, 2001
Page 9 of 63
Channel Lock
Device Mode Keys
No
DEDICATED
Dual Functional via Shift Key
a) One Time Use
b) Shift Lock w/Time-Out
E2 Auto-Sizing
E2 Device Mode Lock
E2 Upgradeable via Modem (997)
E2 Upgradeable via 6 pin interface
Factory Test Mode
Favorite Channel Scan (996)
Functional Keys – Additional
a) brightness Control
b) Color Control
c) Menu
d) Shifted Functions With/without time-outs
e) Teletext – Simple
f) Teletext – Fastext
Functional Keys – Standard
Hidden Keys
High Frequency Capable
ID Code Verification
ID Default Selection
ID Lock/Unlock for Specific Mode
ID – Number of Digits
ID Offset
a) Constant number offset to all Ids
b) Offset by Hardware setting (Jumper,....)
c) Custom renumbering to some or all Ids
No
No
No
No
No
No
Yes
No
No
No
No
No
No
No
Yes
No
No
No
No
No
NA
None
None
None
Illuminated Key Pad
Keymover (994) – Full with Synthesizer
Liquid Crystal Display (LCD)
Low Voltage Detection – Software
Macros
a) Hard Coded
b) Premium Channel
c) User Defined
1) Single
2) Multi-level Rotating
Mode Reassignment (992)
Modem
Network Downloading
Power On Mode Key
Power Toggle
Power Up w/Default Device Mode and Codes
Power Up w/ No Defaults
Viewsonic Tweety RF Remote
Universal Electronics Inc. Confidential
No
No
No
Yes
No
No
No
No
No
No
No
No
No
No
No
Rev 2.9A
November 05, 2001
Page 10 of 63
Punch Through to Last Device (by Key Group)
Record Safety
Remote Finder with Lock Option
No
No
No
Reset to Defaults
a) Operational Reset (980)
b) Manufacturing Reset (981) Section 3.3.4
Set Up Section 3.3.2
Simultaneous Double Key Press - Standard Action
Simultaneous Double Key Press - Alternative Action
Sleep Feature via UEI w/Lock Option
Step and Set (991)
Stuck key Time-Out
No
Custom
Custom
No
No
No
No
Custom
Keypress = 60 sec.
Pointer = 120 sec.
No
No
No
No
No
Synthesizer
Visible LED - for user feedback
Visible LED - for mode indication
Volume Lock
3.1.3 Hardware Information
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
Crystal IR Carrier Operation
Keyboard Layout and # of keys
LCD (Segmented, Pixel), Backlight (LED, EL)
IR LEDs (1,2) (W,WW,WN) [Wide, Narrow]
Lighted Keypad (LED, EL), Color
Low Voltage Detection (Software Controlled)
Mode Indicator LEDs
Modem
PCB Material (Paper phenolic, FR4), Other
PCB Type (Single Sided, Double Sided, Silver thru holes, etc.)
Gold Flash
Plush Port
Plush Port Opening
RAM Retention
RF Operation
16.
17.
18.
19.
20.
RF Finder
Visible LEDs for user feedback (2, 3, 5 mm) (Red, Green)
3 or 6 Volt Operation (AAA,AA) –4AAA
6 pin E2 Interface
Other (describe)
Viewsonic Tweety RF Remote
Universal Electronics Inc. Confidential
Rev 2.9A
No
34
None
NA
No
Yes
No
No
Paper Phenolic
Single Sided
Yes-Varapoint
No
No
NA
Yes
No
No
6V (4 AAA)
No
N/A
November 05, 2001
Page 11 of 63
3.1.4 Mechanical Information
1.
2.
3.
4.
5.
6.
7.
Battery Compartment
Colors & Labels
Force versus Travel (Keypad with Polydome)
IR Lens
Key Clearance
Keypad Definition
List of Consigned Parts
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
Material
Overlay
Packaging Requirements in BOM
Plastic Case design or rendering included
Prototype/Model
Sliding Door
Unique Parts
URC with B00#
Weight
Other (describe)
Yes
Section 8.2.4
Section 8.3.3
No
Section
Yes
Microcontroller
EEprom
RF Transmitter
Varapoint
Section
No
Bulk
Yes
Yes
Yes
No
4012B00
TBD
Viewsonic Jewel
3.1.5 Quality/ Testing Information
1. Environmental Testing
2. ESD Protection
3. FCC or UL Certification Requirements
4.
5.
6.
7.
8.
Yes
Yes
No- Optoma to
apply for
certification UEI
will supply
support.
Production Line Testing Procedures
Quality Assurance Provisions
Reliability Testing
SIO Test Verification
Other (describe)
Viewsonic Tweety RF Remote
Universal Electronics Inc. Confidential
Yes
UEI Standard
Yes
No
N/A
Rev 2.9A
November 05, 2001
Page 12 of 63
3.1.6 Miscellaneous Information
1. Batteries (Included)
2. Battery Cover
a) Rating label silk screened on outside of battery door
3.
4.
5.
6.
7.
8.
9.
10.
11.
Customer Service Support Required
Date Code Label
Labeling
Packaging
Units per Box – shipping
Users Manual Development (Type: staples/folded map)
User Manual Type Responsibility
Device Label- inside addition to package
Country of Origin Location: Molded, Label, Silkscreened
Yes-Bulk
Yes, label to be
installed in
specified area
No
Yes
Yes
Yes-Bulk
100
NA
Customer
Installed on unit
On Rating Label
3.2 Product Library
This will be a dedicated remote.
3.2.1 Target Device Mode Mapping
Mode
Load/ Device Assignment
Viewsonic
Dedicated
3.2.2 Defaults
Mode/Feature
Viewsonic
Default State
RF Channel 1
3.2.3 Library Upgrade Support
N/A
Viewsonic Tweety RF Remote
Universal Electronics Inc. Confidential
Rev 2.9A
November 05, 2001
Page 13 of 63
3.2.4 Key Table
Key #
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
Key Label
POWER
VL+
VLMUTE
CH+
CHPREVIOUS
MENU/EXIT
PIP
ENTER
SMART
REVERSE
PLAY
FFD
RECORD
STOP
PAUSE
INSTANT REPLAY
JUMP COMM
JUMP PRESENT
EPG
+100
MULTIVIEW
RE-SYNC
Make Code
75
74
73
6B
6F
70
6D
6E
6C
57
58
59
5A
5B
5C
5D
5E
5F
60
61
62
13
14
15
16
17
18
19
1A
1B
1C
76
Break Code
F5
F4
F3
EB
EF
F0
ED
EE
EC
D7
D8
D9
DA
DB
DC
DD
DE
DF
E0
E1
E2
93
94
95
96
97
98
99
9A
9B
9C
F6
* SET and Reset in Pointing Device Data Packet
Viewsonic Tweety RF Remote
Universal Electronics Inc. Confidential
Rev 2.9A
November 05, 2001
Page 14 of 63
3.3
Operational Features
Conventions and Notations
The operation of the remote control and the programming sequence use the following
shorthand notations.
The relational operator <<>> around a key is an instruction to press and hold the key for 3
seconds.
For example:
<>
Press RESYNC and hold for 3 seconds
The relational operator <> around a key is an instruction to press the key and then release.
For example:

Viewsonic Tweety RF Remote
Universal Electronics Inc. Confidential
Rev 2.9A
November 05, 2001
Page 15 of 63
3.4
Remote UEI Key and Pointing Device Data Packet
Data Packet Definition:
Byte10
(MSB)
Byte09
Byte08
Byte07
Byte06
Byte05
0x0F
0x0F
0x0F
0x0F
0x55
0x55
Sync Bytes
Preamble
32 bits
16 bits
Sync Bytes:
signal input.
Preamble:
Device Number:
Device Address / Status:
Byte04
Byte03
0-0x63
(0-99
decimal)
Device
Number
8 bits
Dev Addr /
Status
8 bits
X Coord
8 bits
Byte01
Y Coord /
ScanCode
8 bits
Four data bytes of 0x0F each are used to stabilize the demodulation of the Receiver side after a period of no
Two data bytes of 0x55 each are used for decoder bit sync.
Device number from 0 to 99 (decimal)
Batt
b7
Device Address / Status
Described Function
Pointing Device Status
Device Address
b6
b5
b4
b3
b2
b1
b0
RF Receiver
NMB Keyboard Keypad
UEI Remote Control Keypad
NMB Keyboard Pointing Device
UEI Remote Control Pointing Device
Pointing Device Left Button Status (0=Up,
1=Down)
Pointing Device Right Button Status
(0=Up,
1=Down)
X-Coordinate sign bit
(0=Positive, 1=Negative)
Y-Coordinate sign bit
(0=Positive, 1=Negative)
Battery power level Status
X-Coordinate:
Y-Coordinate / Scan Code:
Byte02
(0=Ok,
1=Low)
Keyboard Data (0), X-Data for Pointing Device.
Keyboard Data: Scan Code (Make/Break) [See Table 3: Scan Code Table], Y-Data for Pointing Device.
Viewsonic Tweety RF Remote
Universal Electronics Inc. Confidential
Rev 2.9A
November 05, 2001
Page 16 of 63
Byte0
(LSB)
CheckSum
8 bits
CheckSum:
The sum of Device Number + Device Address / Status + X-Coordinate + Y-Coordinate/Scan Code.
(Add all the indicated bytes without carry’s).
LEFT/RIGHT MOUSE key Operation
1. When the key is pressed, its corresponding pointing device left key status (Bit 3) in the Device Address / Status Byte will be set.
This bit will be set as long as the key is held down, and it will be reset (or cleared) when the key is released.
1.1. While the key is held down:
a) If the Pointing Device is not active, the transmitted data packet will have Left key status bit in the Device Address / Status Byte
set and the X-Coordinate Byte and Y-Coordinate / Scan Code Byte contained all zeros.
b) If the Pointing Device is active, the transmitted data packet will have Left key status bit in the Device Address / Status Byte set
and the X-Coordinate Byte and Y-Coordinate / Scan Code Byte contained the X and Y positional values of the Pointer movement.
1.2. While the key is pressed and held down, if another key (other than key) is now pressed, the pointing device Left key
status bit in the Device Address / Status Byte will be reset.
a) If the Pointing Device is not active, no data packet will be transmitted. Both keys must be released for the remote to return to its
normal operation
b) If the Pointing Device is active prior to the key presses as described in 1.2 above, the transmitted data packet will have Left key
status bit in the Device Address / Status Byte reset and the X-Coordinate Byte and Y-Coordinate / Scan Code Byte contained the
X and Y positional values of the Pointer movement.
2. When the key is pressed, its corresponding pointing device right key status (Bit 4) in the Device Address / Status Byte will be set.
This bit will be set as long as the key is held down, and it will be reset (or cleared) when the key is released.
2.1. While the key is held down:
a) If the Pointing Device is not active, the transmitted data packet will have Right key status bit in the Device Address / Status Byte
set and the X-Coordinate Byte and Y-Coordinate / Scan Code Byte contained all zeros.
b) If the Pointing Device is active, the transmitted data packet will have Right key status bit in the Device Address / Status Byte set
and the X-Coordinate Byte and Y-Coordinate / Scan Code Byte contained the X and Y positional values of the Pointer movement.
2.2. While the key is pressed and held down, if another key (other than key) is now pressed, the pointing device Right key
status bit in the Device Address / Status Byte will be reset.
Viewsonic Tweety RF Remote
Universal Electronics Inc. Confidential
Rev 2.9A
November 05, 2001
Page 17 of 63
a) If the Pointing Device is not active, no data packet will be transmitted. Both keys must be released for the remote to return to its
normal operation
b) If the Pointing Device is active prior to the key presses as described in 2.2 above, the transmitted data packet will have Right key
status bit in the Device Address / Status Byte reset and the X-Coordinate Byte and Y-Coordinate / Scan Code Byte contained the
X and Y positional values of the Pointer movement.
3. When and ) keys are both being held down (with one key is pressed before the other), the corresponding pointing device
left key status (Bit 3) and right key status (Bit 4) in the Device Address / Status Byte will both be set. These bits will be set as long as
the and keys are held down. If any one of these two keys is released first, its corresponding status bit will be reset while
the corresponding status bit of remaining key remains set. Both bits will be reset (or cleared) when both keys are released. During this
time, if the Pointing Device is not active, the X-Coordinate Byte and Y-Coordinate / Scan Code Byte will be all zeros in the transmitted data
packet.
Note: It is up to the Host application software to make use of the case where both left and right key status bits in the Device Address /
Status Byte are set. This condition would indicate that both and keys are currently being pressed and held down.
4. When the Pointing Device is active and one (or both) of (or ) key is pressed, the X-Coordinate Byte and Y-Coordinate /
Scan Code Byte will be updated with the X and Y value of their corresponding positional movements. The transmitted data packet will
have the corresponding Left (or Right) key status bit in the Device Address / Status Byte set or reset accordingly.
Note:
If both keys and are pressed at the same time, this would be considered as invalid (simultaneously key press). There will be
no data packet sent out in this case.
Viewsonic Tweety RF Remote
Universal Electronics Inc. Confidential
Rev 2.9A
November 05, 2001
Page 18 of 63
Re-Sync Data Packet
Byte10
(MSB)
Byte09
Byte08
Byte07
Byte06
Byte05
0x0F
0x0F
0x0F
0x0F
0x55
0x55
Sync Bytes
Preamble
32 bits
16 bits
Byte04
0-0x63
(0-99
decimal)
Device
Number
8 bits
Byte03
Dev Addr /
Status
8 bits
Byte02
Byte01
Byte0
(LSB)
0x00
0x76
0xYY
X Coord
8 bits
Y Coord /
ScanCode
8 bits
CheckSum
8 bits
How does the Re-Sync operates and When the “Re-Sync” code is sent:
Activating the key allows the user to send the “signature data” and to synchronize the RF Transmitter and Receiver RF-channel.
To activate the Re-Sync function:
Press key first.
While key is held down, press a digit key where d is any digit keys from 1, 2, 3, …, 8, 9, 0 representing RF-channel 1,
2, 3, …, 8, 9, 10 respectively.
The process can pictorially be represented as below:
is Key for Digit 1, 2, 3, …, 9, 0
{{ + }}
Press/Release key, while key is held down. The system first sets up “d” RF-channel for RF Transmitter (digit number
corresponding to channel 1 through 10), it then sends out the “Re-Sync” Make code data packet, minimum of 10 or more, as long as key still held
down.
If the and keys are both
The “Sleep” code data packet will be sent when no key activities are detected after 5 seconds (Refer to
released
Sleep Code transmission section for details).
If another key is
The system will setup another RF-channel, corresponding to that digit key, for the Transmitter, it then
sends out another “Re-Sync” Make code data packet in that RF channel setting.
pressed/released while the
This process will be repeating as above in response to different key is pressed/released while
key is still held down
key is still held down.
This Re-Sync signature data transmission process will be repeated as described above each time another key is pressed/released until
both Transmitter and Receiver units match its selected RF-channel. This channel frequency will then be used to transmit the data packet.
Viewsonic Tweety RF Remote
Universal Electronics Inc. Confidential
Rev 2.9A
November 05, 2001
Page 19 of 63
3.4.1 Definitions
Stuck Key Time-out
After any key is pressed continuously for 60 seconds, the remote will stop sending data packets and turn off RF transmission to conserve battery life.
Transmission can begin again, after all keys are released and key is pressed.
Stuck-Key Data Packet
Byte10
(MSB)
Byte09
Byte08
Byte07
Byte06
Byte05
0x0F
0x0F
0x0F
0x0F
0x55
0x55
Sync Bytes
Preamble
32 bits
16 bits
Byte04
0-0x63
(0-99
decimal)
Device
Number
8 bits
Byte03
Dev Addr /
Status
8 bits
Byte02
Byte01
Byte0
(LSB)
0x00
0xFC
0xYY
X Coord
8 bits
Y Coord /
ScanCode
8 bits
CheckSum
8 bits
How and When the Stuck-Key code is sent:
The Stuck-Key Code Data Packet will be sent:
After two data packets of the Make Code of the detected key press, say, have been sent out. If this (same) key, , is still being held down for more
than 60 seconds, then two data packets of Stuck-Key code will be sent with 10 ms delay time interval between data packets. A Make Code data packet of the
same key sent every 70 ms time interval during this 60 seconds stuck key condition.
For the pointing device, after sending out the X-Coord and Y-Coord continuously up to 2 minutes which is the time to be considered as stuck key timeout for
pointing device. Two data packets of Stuck Code will be sent.
Two data packets of Sleep Code will be sent following the Stuck Code data packet. The RF Transmitter will then be turned OFF.
Sleep Mode
This is the idle state of the micro-controller when it draws the least amount of current. Upon entering the idle mode, the remote will transmit a unique byte
(FD) to notify the receiver that it is entering into the sleep mode.
Viewsonic Tweety RF Remote
Universal Electronics Inc. Confidential
Rev 2.9A
November 05, 2001
Page 20 of 63
Sleep Data Packet
Byte10
(MSB)
Byte09
Byte08
Byte07
Byte06
Byte05
0x0F
0x0F
0x0F
0x0F
0x55
0x55
Sync Bytes
Preamble
32 bits
16 bits
Byte04
0-0x63
(0-99
decimal)
Device
Number
8 bits
Byte03
Dev Addr /
Status
8 bits
Byte02
Byte01
Byte0
(LSB)
0x00
0xFD
0xYY
X Coord
8 bits
Y Coord /
ScanCode
8 bits
CheckSum
8 bits
How and When the Sleep code is sent:
The Sleep Code Data Packet will be sent:
After depressed key, say, is released and two Data-Packets of K1 Break Code sent, the RF Transmitter will be turned OFF. If no other key press activities are
detected after 5 seconds, the RF Transmitter will then be turned ON to send two data packets of Sleep code , the RF Transmitter will again be turned OFF and the
remote software goes into its actual Sleep mode.
3.4.1.1 Repeated Make code Data Packet
Byte10
(MSB)
Byte09
Byte08
Byte07
Byte06
Byte05
0x0F
0x0F
0x0F
0x0F
0x55
0x55
Sync Bytes
Preamble
32 bits
16 bits
Byte04
0-0x63
(0-99
decimal)
Device
Number
8 bits
Byte03
Byte02
Byte01
0x00
Dev Addr /
Status
8 bits
X Coord
8 bits
Byte0
(LSB)
0xYY
Y Coord /
ScanCode
8 bits
CheckSum
8 bits
How and When the repeated Make Code is sent:
The repeated Make Code Data Packet will be sent:
After a depressed key, say, is detected, two data packets of its Make code will be sent with 10 ms delay between data packets. The
Make code packet of the same key will be sent out for every 70 ms time interval as long as this is still being held down and the overall
time since its first key press detection does not exceed 60 seconds.
Viewsonic Tweety RF Remote
Universal Electronics Inc. Confidential
Rev 2.9A
November 05, 2001
Page 21 of 63
If another key, say, is pressed while is still held down, the Make code data packet of the same K1 key will be sent out as defined
above. Until is released, two data packets of Break code will be sent with 10 ms delay between data packet. Since is now still
held down, two data packets of Make code will be sent with 10 ms delay between data packets.
Note:
Packet gap between the last Break Code of K1 sent and the first Make Code of K2 sent is 10 ms..
Viewsonic Tweety RF Remote
Universal Electronics Inc. Confidential
Rev 2.9A
November 05, 2001
Page 22 of 63
Timing Events versus Data Packet transmission for various operational situations:
3.4.2 Time Event / Data Packet Transmission Diagram
Te_2
--------------------------- // ------------------------ // ------------------ 60 seconds ---------------- // ------------------------ // ----------------- ~ 70ms -- //
~10ms~
Te_2a
Te_3
Te_3a, Te_1a
Te_1
~10ms~
Make
Make
Break
Break
Te_3b, Te_6a
Te_3c, Te_6a
Te_1a
Make
Te_4
Make
- // ---- 70ms --- // -----
Te_4a
Notes:
Make
StkKy
Sleep
Te_4b
Te_5
Te_5a
Te_6a
- // ---- 70ms -- // ----
Time values are approximate and NOT to scale
Te_6
Refer to APPENDIX for notation descriptions used in this Diagram and Table below.
Time Event / Data Packet Transmission
Time Event
Key Press & Time Event
Data Packet Transmission & Time Event
Remark
Te_1
is pressed and detected
Te_2
key is still being
depressed
First Make-Code-Data-Packet ( Scan Code) will be sent. It follows by
about 10 ms delay.
Second Make-Code-Data-Packet (of same Scan Code as above) will
be sent.
Case where a key press, say, is
detected. Make-Code-Data-Packets are
sent with 10 ms delay between the data
packets.
Te_4
70 ms after Te_2, is still
being held from the time event
Te_1 when the depress
is first detected..
Make code data packets of K1 are now transmitted.
This is the case where:
From the time event Te_1 and for
every 70 ms elapsed time interval, and
60 seconds stuck-key timeout has not
been reached, Make code Data-Packet
of the same key will be sent out as long
as key is still being held down.
Te_4a
Te_4b
Another 70 ms elapsed after
Te_4 and is still being
held down
is still being held down
70 ms after Te_4a.
Viewsonic Tweety RF Remote
Universal Electronics Inc. Confidential
Another Make code Data Packets are sent
Another Data Packet of Keep-Alive code is sent. See remark column.
Rev 2.9A
November 05, 2001
Page 23 of 63
Time Event / Data Packet Transmission Diagram (continued)
Te_2
--------------------------- // ------------------------ // ------------------ 60 seconds ---------------- // ------------------------ // ----------------- ~ 70ms -- //
~10ms~
Te_2a
Te_3
Te_3a, Te_1a
Te_1
~10ms~
Make
Make
Break
Break
Te_3b, Te_6a
Te_3c, Te_6a
Te_1a
Make
Te_4
Make
- // ---- 70ms --- // -----
Te_4a
Notes:
Make
StkKy
Sleep
Te_4b
Te_5
Te_5a
Te_6a
- // ---- 70ms -- // ----
Time values are approximate and NOT to scale
Te_6
Refer to APPENDIX for notation descriptions used in this Diagram and Table below.
Time Event / Data Packet Transmission (continued)
Time Event
Key Press & Time Event
Data Packet Transmission & Time Event
Remark
Te_3
70 ms after Te_2a:
key is now released.
Two Break-Code-Data-Packets (of Scan Code) will be sent, separated
by about 10 ms time interval between them.
70 ms from the last Make-Code-DataPacket sent and released.
Te_3a, Te_1a
70 ms after Te_2a:
is released but another
key is pressed, say
within 5 seconds.
Two Break-Code-Data-Packets (of Scan Code) sent with 10 ms
separation. The RF Transmitter will then be turned OFF. When another key,
, is pressed within 5 seconds, the RF Transmitter will be turned ON to
send two Make-Code-Data-Packets of K2 (10 ms between packets) as shown
at Te_1a
Te_3b, Te_6a
70 ms after Te_2a:
is released but NO other
key press detected after 5
seconds elapsed.
Two Break-Code-Data-Packets (of Scan Code) will be sent with 10
ms time delay in between when is released. Since no other key press
is detected beyond 5 seconds, a Sleep-Code-Data-Packet will be sent, the RF
transmitter will then be turned OFF to conserve the power.
Te_3c,
Te_5a
Te_6a
70 ms after Te_2a:
While is still being held
down, another key, say,
is pressed
Viewsonic Tweety RF Remote
Universal Electronics Inc. Confidential
Make code data packet of K1 sent as defined before. If released, Break code
data packets of K1 sent, 10 ms later, Make code data packet of K2 sent. If
is still down, Make code data packet of K2 sent, etc.. , until
released, then Break code data packet of K2 sent.
Rev 2.9A
November 05, 2001
Page 24 of 63
Case where released, and
pressed within 5 seconds after
released.
Case where released and no
other key press is to be followed after
more than 5 seconds.
Case of Sequence BreakCode/Stuck/Sleep to indicate the
situation.
Key Type Data Packet Transmission, a Summary:
All keys including the pointing device buttons are Make/Break type. When a key or button is pressed, the remote will transmit the data packet as shown in the
protocol on previous pages.
For reliable data transmission, keystroke and control push buttons data packets are transmitted twice wirelessly from the Remote Control RF Transmitter. The
transmission is one time for Keep-Alive code and a minimum of 10 times for Re-Sync code.
MAKE
10ms
MAKE
BREAK
10ms
BREAK
Followings are some scenarios of key press:
Case of a normal Key pressed/released:
Key Pressed
Key Released
Make Code sent.
Break Code sent, RF Transmitter turned OFF.
If no key press is detected after 5 seconds, RF Transmitter is turned ON and Sleep Code is sent. After that the RF
Transmitter is again turned OFF and the unit goes to SLEEP mode.
If a key press is detected within 5 seconds, that key data transmission will be serviced as described above.
If a key pressed then stuck for a long time, then Make Code of the same depressed key will be sent for every 70 ms time
interval within 1 minute from the time the original Make code sent. When 1 minute duration is expired, a Stuck code will be
sent, followed by Sleep code and the RF Transmitter is then turned OFF. Note that the software would only be able to go
to STOP (or SLEEP) mode when a stuck key is released.
Case of Make code kept resend (use and as an example):
pressed
Make Code of K1 sent.
is then pressed while is still down and both keys are now down within 1 minute. The Make code of K1 will be
sent for every 70 ms time interval as described above, until one of the following conditions occurs:
is released first while is still held down. Break code of K1 will be sent and Make code of K2 will be
sent after 70 ms.
is released first while is still held down. Nothing changes except the same Make code of K1 will be
sent for every 70 ms time interval. Until is released and its Break code is sent.
Viewsonic Tweety RF Remote
Universal Electronics Inc. Confidential
Rev 2.9A
November 05, 2001
Page 25 of 63
Case of Re-Sync data packet sent:
{{+}} A key is pressed while key is held down:
A minimum of 10 data packets of Re-Sync code (0x76) will be sent with 10 ms delay separated each data packet. Or the
Re-Sync data packets will be kept sending out as long as the keys are held down.
Viewsonic Tweety RF Remote
Universal Electronics Inc. Confidential
Rev 2.9A
November 05, 2001
Page 26 of 63
APPENDIX
Some notations used in the Time Event / Data Packet Diagram
Notation
Make
Break
ReSyn
StkKy
Sleep
Te_ij

Function Description
Make Code for Scan Code of Keyboard Keypad or Remote Keypad, or XCoordinate, or Y-Coordinate of the Pointing Device
Break Code for Scan Code of Keyboard Keypad or Remote Keypad, or XCoordinate, or Y-Coordinate of the Pointing Device
Make Code for Re-Sync
Make Code for Stuck-Key
Make Code for Sleep
Time Event _ij, where i = 1, 2, 3, etc …
and j = nothing (empty) or a, b, c, etc …
First Key press in the sequence of key press events
Second Key press in the sequence of key press event after
Viewsonic Tweety RF Remote
Universal Electronics Inc. Confidential
Rev 2.9A
November 05, 2001
Page 27 of 63
3.4.3 Device Number Setup
Note: To prevent possible interference from multiple users environment, each remote will be set to a specific User Device Number (User DN#, between 00 to
99). If the User DN# has not been setup, the OSD will prompt the user to program a device number setup.
To program, press key first then press key, hold down both keys for about 3 seconds, then released:
< + >
1. The software is now expecting the user to enter two digit numbers representing the device number by press/release keys. (In
the software test module, this process completes with 2 LED blinks indication).
2. If key, other than keys, is pressed after the above sequence, the software will abort the Device Number Setup mode. (In
the software test module, this error condition will be indicated by a long LED blink).
3. Within 10 seconds (timeout value) after the above sequence entry, if NO key is pressed (or the timeout expired between key press),
the software will exit the Device Number Setup mode and the remote will retain the current settings. The software will then return to its normal
operation without having the device number updated. During this 10 seconds time, if the Pointer device is activated, the software will exit the
Device Number Setup mode and will service the pointer movement of the remote.
Each Remote has a Device ID and a Device Number (00-99). The Device ID shows the category of the Remote. The Host will validate the
received data packet from the Remote, by checking the Device Number, to see if it has been registered for that Device ID or not.
After the channel synchronization, the Device ID and Device Number of each Remote will be registered in the Host.
Note: For both Keyboard and Remote Control, the Keypad and Pointing Device have the same Device Number. During synchronization, only Device ID
of the Keypad and the Device Number of the Pointing Device will be sent. The Host should also register the Device Number for the Pointing Device of
the corresponding device.
Viewsonic Tweety RF Remote
Universal Electronics Inc. Confidential
Rev 2.9A
November 05, 2001
Page 28 of 63
3.4.4 RF Channel Change
Re-Sync Data Packet
Byte10
(MSB)
Byte09
Byte08
Byte07
Byte06
Byte05
0x0F
0x0F
0x0F
0x0F
0x55
0x55
Sync Bytes
Preamble
32 bits
16 bits
Byte04
0-0x63
(0-99
decimal)
Device
Number
8 bits
Byte03
Dev Addr /
Status
8 bits
Byte02
Byte01
Byte0
(LSB)
0x00
0x76
0xYY
X Coord
8 bits
Y Coord /
ScanCode
8 bits
CheckSum
8 bits
How does the Re-Sync operates and When the “Re-Sync” code is sent:
Activating the key allows the user to send the “signature data” and to synchronize the RF Transmitter and Receiver RF-channel.
To activate the Re-Sync function:
Press key first.
While key is held down, press a digit key where d is any digit keys from 1, 2, 3, …, 8, 9, 0 representing RF-channel 1, 2, 3, …,
8, 9, 10 respectively.
The process can pictorially be represented as below:
{{ + }}
is Key for Digit 1, 2, 3, …, 9, 0
Press/Release key, while key is held down. The system first sets up “d” RF-channel for RF Transmitter (digit number
corresponding to channel 1 through 10), it then sends out the “Re-Sync” Make code data packet, minimum of 10 or more, as long as key still held
down.
If the and keys are both
released
Viewsonic Tweety RF Remote
Universal Electronics Inc. Confidential
Rev 2.9A
No Break Code data packet for “Re-Sync” will be sent. The “Sleep” code data packet will be sent
when no key activities are detected after 5 seconds (Refer to Sleep Code transmission section for
details).
November 05, 2001
Page 29 of 63
If another key is
pressed/released while the
key is still held down
The system will setup another RF-channel, corresponding to that digit key, for the Transmitter, it then
sends out another “Re-Sync” Make code data packet in that RF channel setting.
This process will be repeating as above in response to different key is pressed/released while
key is still held down.
This Re-Sync signature data transmission process will be repeated as described above each time another key is pressed/released until
both Transmitter and Receiver units match its selected RF-channel. This channel frequency will then be used to transmit the data packet.
Viewsonic Tweety RF Remote
Universal Electronics Inc. Confidential
Rev 2.9A
November 05, 2001
Page 30 of 63
3.4.5 E2 Initialization
EEPROM Initialization:
Note: The EEPROM device must have been previously initialized for the remote to be able to
get into the Factory RF Channel Test Mode.
Press key first then press key, hold down both keys for about 3 seconds, then
released. The software will enter the E2 Initialization mode WHEN the key is pressed
and released after the above described sequence.
< + >
1. If key is pressed/released after the above sequence, the software will initialize
the EEPROM. (In the software test module, this process completes with 4 LED blinks
indication)
2. If key, other than key, is pressed after the above sequence, the
software will abort the EEPROM Initialization mode. (In the software test module, this
error condition will be indicated by a long LED blink).
Within 10 seconds (timeout value) after the above sequence entry, if NO key is pressed, the
software will exit the EEPROM Initialization mode and the EEPROM device will not be initialized.
The software will then return to its normal operation. But during this 10 seconds time, if the
Pointer device is activated, the software will exit the EEPROM Initialization mode and will service
the pointer movement of the remote.
Viewsonic Tweety RF Remote
Universal Electronics Inc. Confidential
Rev 2.9A
November 05, 2001
Page 31 of 63
3.4.6 Factory Test Mode(s)1
To enter this RF Channel test mode, press and hold a combination keys <<1>+<3>> for at least 3
seconds then released, within 6 seconds after the battery/power is applied to the unit:
<<1> + <3>>2
The software will start with setting up RF-channel 1 and send through the Transmitter the entire
packet for the first channel continuously for the first 300 ms, with a 10-20ms gap between each
channel. The process is automatically with the next RF-channel setup until all 10 RF-channels
have been cycled through per Table1 below:
3.4.6.1
Table1: Factory Test Mode for RF Channel Test
Test Channel
End test
Time (ms)
Packet Sent
0 - 300
300 - 400
400 - 700
700 - 800
800 - 1100
1100 - 1200
1200 - 1500
1500 - 1600
1600 -1900
1900 - 2000
2000 - 2300
2300 -2400
2400 - 2700
2700 - 2800
2800 - 3100
3100 - 3200
3200 - 3500
3500 - 3600
3600 - 3900
3900
0F 0F 0F 0F 55 55 FF FF 01 01 00
Nothing sent while changing RF Ch. 1
0F 0F 0F 0F 55 55 FF FF 02 02 02
Nothing sent while changing RF Ch. 2
0F 0F 0F 0F 55 55 FF FF 03 03 04
Nothing sent while changing RF Ch. 3
0F 0F 0F 0F 55 55 FF FF 04 04 06
Nothing sent while changing RF Ch. 4
0F 0F 0F 0F 55 55 FF FF 05 05 08
Nothing sent while changing RF Ch. 5
0F 0F 0F 0F 55 55 FF FF 06 06 0A
Nothing sent while changing RF Ch. 6
0F 0F 0F 0F 55 55 FF FF 07 07 0C
Nothing sent while changing RF Ch. 7
0F 0F 0F 0F 55 55 FF FF 08 08 0E
Nothing sent while changing RF Ch. 8
0F 0F 0F 0F 55 55 FF FF 09 09 10
Nothing sent while changing RF Ch. 9
0F 0F 0F 0F 55 55 FF FF 00 00 FE
Nothing sent while changing RF Ch. 10
FACTORY TEST MODE can be entered upon cold power up and/or warm power up
IF E2 is not initialized, the remote will not enter the FACTORY TEST MODE.
Viewsonic Tweety RF Remote
Universal Electronics Inc. Confidential
Rev 2.9A
November 05, 2001
Page 32 of 63
Key Test (Also used in Factory Test for Key):
An integrated hardware/firmware/software test unit will be designed for the Key Test. This Key
Test Unit can be used during this project software development as well as for factory test in an
actual production manufacturing. No special combination key sequence is required to get into this
Key Test mode.
The integrated Key Test unit is functionally represented as below:
RF
Receiver
Firmware
Unit
Input:
Manchester
code from
RF Receiver
output
Output:
RS-232
TxD
------------------------------------------→
RxD
←-----------------------------------------+5V
--------------------------------------------GND
---------------------------------------------
Software
Unit
Input:
RS-232
Computer
Screen
Output:
Display on
Computer
Monitor
Monitor
RS-232 interface (9600 baud)
Viewsonic Tweety RF Remote
Universal Electronics Inc. Confidential
Rev 2.9A
November 05, 2001
Page 33 of 63
3.4.6.1 Firmware Unit:
This so-called “unit” is actually a firmware portion that processes to keep 5 bytes of the 11-byte
data packet after striping off all the Sync bytes and Preamble bytes. It then output these 5 bytes
through the RS-232 protocol format.
Byte4
Byte3
Byte2
Device Number
DevAddr/Status
X-coordinate
(8 bits)
(8 bits)
(8 bits)
Byte0
Byte1
Byte2
Byte3
Byte4
Byte1
Y-coordinate /
Scan Code
(8 bits)
Byte0
CheckSum
(8 bits)
CheckSum
The result of the addition (without carry) of Byte1 through Byte4
(Device Number + Device Address / Status + X-coordinate + Y-coordinate /
Scan Code)
Y-coordinate / Scan Code
Y-data for Remote Control Pointing Device, or
Make/Break Scan Code of the pressed/released key on the Remote Control
Keypad. See Table2 for details.
X-coordinate
X-data for Remote Control Pointing Device.
Always 0 for Remote Control Keypad
Device Address / Status
Please refer to details on next page
Device Number
Device Number is chosen from 0 to 99 by system Host interface. The Host
will validate the received data packet by checking the Device Number if it is
registered for that device.
Viewsonic Tweety RF Remote
Universal Electronics Inc. Confidential
Rev 2.9A
November 05, 2001
Page 34 of 63
Byte3 details:
Device Address / Status
b7
b6
b5
b4
b3
b2
b1
Details Byte3 Description
b0
0 UEI Remote Control Keypad
0 UEI Remote Control Pointing Device
Pointing Device Left Button Status (0=Up,
1=Down)
Pointing Device Right Button Status
Positive
Negative
Positive
Negative
OK, good
Low
Viewsonic Tweety RF Remote
Universal Electronics Inc. Confidential
Rev 2.9A
(0=Up,
1=Down)
Sign Bit of X-coordinate
Sign Bit of Y-coordinate
Battery power level status
November 05, 2001
Page 35 of 63
3.4.6.2 Software Unit:
This so-called “unit” is actually a software portion (in the integrated Key Test Unit). After it
receives a data packet of 5 bytes, as described above, through the RS-232 communication
protocol, it will display the output on the computer screen monitor. The display output information
will depend on the data input information received from the RS-232 inputs.
The display output will be designed as such:
•
All 34 keys (Table2, columns 1 & 2) are to be programmed to be graphically displayed as key
buttons (with proper key label if possible). A color-coded scheme are to be designed to
visually represent the key status condition depending on (b2b1b0=010 in the Device Address
/ Status byte).
Color-coded
Gray
Red
Green
Key press status
Indicates a key that had never been pressed and/or released, or
the key is malfunctioned that the remote could not detect when
pressed.
Indicates when the key is pressed and the software receives its
Make Code corresponding to that key.
Indicates when the key is released and the software receives its
Break Code corresponding to that key.
•
Two allocated display locations on the screen monitor are to be programmed to show the
value of X-coordinate and Y-coordinate of the Pointing Device. These values are data
received in Byte2 and Byte1 when the pointing device on the remote control is activated
(b2b1b0=100 in the Device Address / Status byte).
•
An allocated display location on the screen monitor is to be programmed to show the status
of the battery level condition. This status is to be decoded from bit b7 of Byte 3 (Device
Address / Status byte) in the received data packet.
•
An allocated display location on the screen monitor is to be programmed to show the Device
Number. This value is to be extracted from Byte4 in the received data packet.
Viewsonic Tweety RF Remote
Universal Electronics Inc. Confidential
Rev 2.9A
November 05, 2001
Page 36 of 63
Table2: Key Test (Also used for Factory Key Test)
Note: Make Code and Break Code are in Hexadecimal.
Key #
Key Label
Make Code
POWER
75
VL+
74
VL73
MUTE
6B
CH+
6F
CH70
PREVIOUS
6D
MENU/EXIT
6E
PIP
6C
10
ENTER
11
SMART
12
REVERSE
57
13
PLAY
58
14
FFD
59
15
RECORD
5A
16
STOP
5B
17
PAUSE
5C
18
INSTANT REPLAY
5D
19
JUMP COMM
5E
20
JUMP PRESENT
5F
21
EPG
60
22
+100
61
23
MULTIVIEW
62
24
13
25
14
26
15
27
16
28
17
29
18
30
19
31
1A
32
1B
33
1C
34
RE-SYNC
76
* Set and Reset in Pointing Device Data Packet
Break Code
F5
F4
F3
EB
EF
F0
ED
EE
EC
D7
D8
D9
DA
DB
DC
DD
DE
DF
E0
E1
E2
93
94
95
96
97
98
99
9A
9B
9C
F6
Other allocated display locations on the screen monitor:
ID Number : xx
Battery Good / Battery Low
X-data of Pointing Device
Viewsonic Tweety RF Remote
Universal Electronics Inc. Confidential
Y-data of Pointing Device
Rev 2.9A
November 05, 2001
Page 37 of 63
3.4.7 Low Battery Indicator
When the batteries in the unit reach approximately 3.4 Volts the remote will send a specific frame
of data to indicate the remote batteries are low. The user will be prompted via an onscreen
display to change the batteries.
When the unit's batteries reaches 2.9 Volts +/- 200 mV the remote will not respond to key presses.
Viewsonic Tweety RF Remote
Universal Electronics Inc. Confidential
Rev 2.9A
November 05, 2001
Page 38 of 63
4 RF Transmission General Specification
The performance requirements are contained in the table below
Table 2. General Specification
Rqmt No.
4.1
4.2
4.3
4.4
4.5
4.6
4.7
4.8
4.9
Parameter
Number of channels
Channel spacing
Receive frequency band
Demodulation
Receiver sensitivity
Data rate
Transmit frequency
band
Modulation
Radiated power
Description
Minimum
Fixed
Maximum
Fundamental
FCC Requirements
Spurious
emissions
4.10
4.11
4.12
Simplex type
RF frequency tolerance
Temperature range
4.13
4.14
Power source
Power consumption
4.15
4.16
4.17
Dimensions
Weight
Other requirements
Operating
Storage
Nominal
Maximum
operational
supply current
PLL lock on time
Tx Module
10 channels
1,2,3 & 1.6 MHz
N/A
N/A
N/A
9600 bps
2446.7 to 2464.3 MHz
FSK
-18 dBm
50 millivolts/meter @ 3
meters
500 microvolts/meter
@ 3 meters
Transmit only
± 10 ppm
0 to 50 °C
-10 to 60 °C
2.5 VDC
15 mA
28mm x 22mm x 8mm
To be determined
50 ms
Note
* : The output data of channel 1-5 and channel 6-10 are different.
Channel 1~5 : Tx input data
Rx output data
Channel 6~10: Tx input data
Rx output data
Viewsonic Tweety RF Remote
Universal Electronics Inc. Confidential
Rev 2.9A
November 05, 2001
Page 39 of 63
4.1
Data Coding
Data coding is necessary for the wireless communication, which is to eliminate the DC offset of the
demodulation caused by the series 1’s or 0’s. Following describes Manchester Coding implementation:
Viewsonic Tweety RF Remote
Universal Electronics Inc. Confidential
Rev 2.9A
November 05, 2001
Page 40 of 63
5 Hardware Interface
The interface to the module shall be as described in the table below.
Table 1. Hardware Interface
Parameter
Input voltage - Vcc
Ground
Data
Synthesizer enable
Synthesizer SDA
Synthesizer SCK
Pin Number
Tx Module
2.2 volts
Ground
Data input
TTL input
TTL input
TTL input
5.1 Transmitter Outline /Interface
Dimension 28* 22*8 mm or smaller if 04/02 components are used
1.
2.
3.
4.
5.
6.
Vcc (2.2 V)
GND
Data in (Vp-p = 0.1V)
LE (TTL)
SDA (TTL)
SCK (TTL)
( Top View )
Viewsonic Tweety RF Remote
Universal Electronics Inc. Confidential
Rev 2.9A
November 05, 2001
Page 41 of 63
5.1
5.1.1
Product Performance Requirements
RF CHANNEL and OPERATING BANDS
2400 to 2483.5 MHz
5.1.2
RF Channels and Frequencies
Channel
Tx module transmit
frequency
2446.7 MHz
2448.7 MHz
2449.7 MHz
2451.7 MHz
2454.7 MHz
2456.3 MHz
2457.3 MHz
2459.3 MHz
2462.3 MHz
2464.3 MHz
Frequency Control
Serial data is processed using the SDA, SCK, LE pins. Serial data controls the RF module. Binary
serial data is entered through the SDA pin. One bit of data is shifted into the shift register on the
rising edge of the clock (SCK). When the load enable (LE) pin is high, stored data is latched. After
the both 19-bit register being latched, the frequency will be locked.
CH
6*
7*
8*
9*
0*
Freq.
2446.7 MHz
2448.7 MHz
2449.7 MHz
2451.7 MHz
2454.7 MHz
2456.3 MHz
2457.3 MHz
2459.3 MHz
2462.3 MHz
2464.3 MHz
Transmitter
19-bit Register
0010000000001010001
0010000000001010001
0010000000001010001
0010000000001010001
0010000000001010001
0010000000001010001
0010000000001010001
0010000000001010001
0010000000001010001
0010000000001010001
19-bit Register
0010111111000100110
0010111111001001110
0010111111001100010
0010111111010001010
0010111111011000110
0010111111101100110
0010111111101111010
0010111111110100010
0010111111111011110
0011000000010000110
*Channels 6,7,8,9, and 0 will be inverted when transmitted.
Viewsonic Tweety RF Remote
Universal Electronics Inc. Confidential
Rev 2.9A
November 05, 2001
Page 43 of 65
5.1.3
Pulse Width Timing for RF Transmitter
Long Low:
Long High:
Short Low:
Short High:
5.1.4
108.0us
102.0us
53.0us
50.0us
(+/- 5%)
(+/- 5%)
(+/- 5%)
(+/- 5%)
RF Channel Operation Range
The remote shall communicate at a minimum distance of 5m in a direct line of site
5.1.5
RF Modulation Scheme and Modulation Level
Modulation Scheme
Frequency Shift Keying (FSK
Modulation Level
± 70 kHz (Nominal)
5.1.6
Maximum Bit Rate
9600 baud (bps)
5.1.7 RF Power Management
RF Power On
Allocate Frequency
Tx Data Input
T1
T2
•
T1 = Power On Stable Time. Typically, it should be T1 > 5ms
•
T2 = Frequency Stable Time. Typically, it should be T2 > 20ms
5.1.8 Transmitter Data Input Level
The transmitter data input level should be fixed as the supply voltage drops when using battery. It
is required that the Input level will be Vp-p = 100mv (+/- 10%).
5.1.9
Communication Link
Simplex – one way communication from remote control unit to base unit.
SERIAL INPUT DATA TIMING
Viewsonic Tweety RF Remote
Universal Electronics Inc. Confidential
Rev 2.9A
November 05, 2001
Page 44 of 63
Viewsonic Tweety RF Remote
Universal Electronics Inc. Confidential
Rev 2.9A
November 05, 2001
Page 45 of 63
6 Electrical Requirements
6.1
Power
The remote shall operate from (4 - AAA) alkaline batteries. Power requirements shall be a maximum
operating voltage of 6.4 volts.
6.2
Visible LEDs
NA
6.3
Transmission IC
Samsung 16K (S3P/C80F9XFE-QZR5) (QFP)
6.4
Battery Life
4 new AAA cells will provide approximately 10 months of battery life.
This is the time at which the remote will begin sending the specific
frame of data to indicate the remote batteries are low.
This assumes the following usage:
5 hours of operation per day
Approximately:
14.4 key presses per hour (@ 1 second each)
120 Seconds of Pointer operation per hour
6.5
Range
Minimum 5meters in direct line of site.
Viewsonic Tweety RF Remote
Universal Electronics Inc. Confidential
Rev 2.9A
November 05, 2001
Page 46 of 63
7 Mechanical Requirements
7.1.1 HRC Assembly
The HRC assembly must meet UEI mechanical drawing and industrial design requirements.
7.1.2 Assembly LED’s
NA
7.2
Enclosure
7.2.1 Enclosure and Battery Cover Shape
The shape of the enclosing plastic parts including the top case, bottom case and
battery cover can be specified by a set of mechanical part drawings and CAD files in
the form of DXF and/or IGES format or Pro-E, Ashlar Vellum or AutoCAD format.
7.2.1.1 Part Form
All plastic parts must meet the shape and proportions embodied in their respective
UEI mechanical drawings and industrial designs.
7.2.1.2 Part Alignment & Mismatch
All plastic parts must align correctly as specified in the respective UEI mechanical
drawings.
7.2.1.3 Battery Cover
The battery cover shall be designed to have a minimal lateral movement in the
battery compartment and to disengage the latch mechanism at 700±300 grams.
7.2.2
Material
Recommended material selection for standard use plastic parts is ABS GPM,
ABS T- grade or other engineering approved resin. The properties are
described as follow:
Physical:
Specific Gravity, solid
1.02-1.05
Mechanical:
Tensile Strength
Tensile Modulus
Flexural Strength
Flexural Modulus
5,000-6,900 psi (35-50 MPa)
260,000- 360,000 psi (1,800-2,500 MPa)
8,500-12,300 psi (60-85 MPa)
270,000-380,000 psi (1,900-2,600 MPa)
Viewsonic Tweety RF Remote
Universal Electronics Inc. Confidential
Rev 2.9A
November 05, 2001
Page 47 of 63
7.2.3
Impact:
Izod Impact @ 73°F
Izod Impact @ -40°F
3.1-7.5 ft-lb/in (170-400 J/m)
1.2-2.6 ft-lb/in (65-140 J/m)
Flame Class Rating:
UL94HB
0.0579-0.0630 in. (1.47-1.6mm)
Texture
Texture shall be Mold-Tech MT-11010 or UEI engineering approved
equivalent as follows:
UEI SPEC.
(MOLD-TECH)
MT-11010
7.2.4
HONG KONG
(YICK SANG)
D-428
CHINA
(HON NGAI)
MK-111
SIN OR MEXICO
(PHILIPS)
9-410-UN-D249
KOREA
(KYUNG SUNG)
K-112G
Color
The Pantone Matching System (PMS) will be used as the general UEI color standard. Refer to the
“Pantone Color Formula Guide 1000” for specific color selection and color coordination.
7.3
Keypad with Polydome
For further detailed information, see the UEI Keypad Design Guideline Manual
(Spec. # 0004).
7.3.1
Material
The keypad is usually molded from compression molded silicon rubber. The
recommended material shall be 50 to 60 shore A hardness, which provides good tactile
feel and long life.
Physical
Specific Gravity @ 25C
Durometer (Shore A)
Tensile Strength
Compression Set %
Insulation Breakdown
1.1-1.4
55 ± 5
55 - 75 kg/cm2
11 - 22
26 kV/mm
Flame Class Rating
UL94HB
The Polydome assembly is a die cut Polyethylene terephthalate (PET) sheets. It contains
0.05mm main dome sheet, adhesive, and 0.1mm spacer. The travel and tactile feed back
are provided by the main dome sheet.
7.3.2
Tactile Feel
The switch should operate smoothly throughout its entire travel with good tactile feedback.
Viewsonic Tweety RF Remote
Universal Electronics Inc. Confidential
Rev 2.9A
November 05, 2001
Page 48 of 63
7.3.3
Force Vs. Travel
The force values are represented by gram and the travel values are represented by
millimeter.
P1 (Peak force)
General range: 200±50 grams and it is dependent on specific
product application; therefore, see the keypad part drawing for
exact specification.
P2 (Contact force)
General range: 50-90% of P1.
PR (Return force)
40 grams minimum.
S (Travel)
0.4 ± 0.1mm and it is dependent on specific product
application; therefore, see the keypad part drawing for exact
specification.
Force
(gram)
P1
P2
PR
Travel (mm)
Figure 1: Force vs. travel
Rubber keypad
only
Keypad with
polydome
Peak force, P1
150±30 grams
Return force, PR
Snap ratio, TR
40 grams minimum 40% to 60%
Stroke, S
1.0±0.2mm
200±30 grams
40 grams minimum 40% to 70%
0.4±0.1mm
Viewsonic Tweety RF Remote
Universal Electronics Inc. Confidential
Rev 2.9A
November 05, 2001
Page 49 of 63
7.3.4 Life
Key Pad with Polydome
All keys must continue operation within specification, after being subjected to500,000 cycles of
key activation at , 250 grams of force @ 120 cycles per minute under normal operating conditions.
7.3.5 Keypad Pull-out Force
The key top must not be separated from its base after 1kg vertical pull up force is applied.
7.3.6
Key stick and key stuck
All keys should rebound to their original height smoothly and instantaneously. All keys should
not get stuck under the key openings whichever location of the key is pressed.
7.4
PCB Material
Material specification needs to be provided to Engineering and approved by Engineering prior to
usage. Layout shall be based on UEI Specification 0029. If carbon ink is used, UEI Specification
0007 should be followed.
7.5
Battery Compartment
•
•
•
•
•
•
•
•
7.6
The battery compartment must be clearly marked for battery size and polarity.
The battery compartment must be designed to accommodate all brands per American National
Standard Dry Cell and Battery Specification (ANSI C18.1M-1992).
The battery must be retained by coil or leaf springs, tight enough to avoid rocking and loose
enough for easy replacement.
The battery compartment must be designed to prevent contact in case of reverse polarity
during installation.
The batteries must remove from the battery compartment when a force of 300 to 500 grams is
exerted outward.
The battery springs must be properly positioned to make contact with the batteries.
The battery springs must remain properly seated when a force of 500 grams is applied.
The battery springs must be insulated from each other.
Printing
A pad printing or silk-screening process shall be used for all legends that print on plastic surface. A
silkscreen printing process shall be used on keypad.
All printing shall be free of visible blurs, alignment, or any distortion defects. Ink thickness shall be
sufficient to cover the underlying material’s color.
Viewsonic Tweety RF Remote
Universal Electronics Inc. Confidential
Rev 2.9A
November 05, 2001
Page 50 of 63
Key name
Rubber Pantone color
Case label text
Power
MENU/EXIT
VOL UP
VOL DN
CH UP
CH DN
ENTER
SMART
MUTE
PIP
GS 056
NMB Midnight Gray ABT 10936A
NMB Midnight Gray ABT 10936A
NMB Midnight Gray ABT 10936A
NMB Midnight Gray ABT 10936A
NMB Midnight Gray ABT 10936A
NMB Midnight Gray ABT 10936A
DS 161
NMB Midnight Gray ABT 10936A
NMB Midnight Gray ABT 10936A
European Power Symbol
PREV CH
NMB Midnight Gray ABT 10936A
NMB Midnight Gray ABT 10936A
NMB Midnight Gray ABT 10936A
NMB Midnight Gray ABT 10936A
REWIND
PLAY
FAST
FORWARD
RECORD
STOP
PAUSE
NMB Midnight Gray ABT 10936A
NMB Midnight Gray ABT 10936A
NMB Midnight Gray ABT 10936A
DS 161
INST
REPLAY
JUMP
COMM
JUMP
PRESENT
EPG
+100
MULTIVIEW
RESYNC
Key label
text
MENU/EXIT
VOL
CH
ENTER
SMART
MUTE
PIP
PRE CH
Case / Key label
Pantone Color
NMB White U
NMB White U
NMB White U
NMB White U
NMB White U
NMB White U
NMB White U
NMB White U
NMB White U
NMB White U
NMB White U
NMB White U
NMB White U
NMB White U
INST REPLAY
Pantone 1788
NMB White U
NMB White U
NMB White U
DS 161
JUMP COMM
NMB White U
DS 161
JUMP
PRESENT
EPG
+100
MULTIVIEW
NMB White U
DS 161
DS 161
DS 161
NMB Midnight Gray ABT 10936A
NMB Midnight Gray ABT 10936A
NMB Midnight Gray ABT 10936A
NMB Midnight Gray ABT 10936A
NMB Midnight Gray ABT 10936A
NMB Midnight Gray ABT 10936A
NMB Midnight Gray ABT 10936A
NMB Midnight Gray ABT 10936A
NMB Midnight Gray ABT 10936A
NMB Midnight Gray ABT 10936A
NMB Midnight Gray ABT 10936A
II
RESYNC
NMB White U
NMB White U
NMB White U
NMB White U
NMB White U
NMB White U
NMB White U
NMB White U
NMB White U
NMB White U
NMB White U
NMB White U
NMB White U
NMB White U
Housing will be NMB Midnight Gray ABT 10936A for top and back case.
Viewsonic Tweety RF Remote
Universal Electronics Inc. Confidential
Rev 2.9A
November 05, 2001
Page 51 of 63
7.7
7.7.1
Labeling
Date Code
All assembly units require date code information. This information shall be marked inside the
battery compartment in a form hot stamp/cold stamp or label. The date code information contains
seven alphanumeric digits as describe below:
XXXXXXX
First Digit
Second and Third Digit
Fourth and Fifth Digit
Sixth and Seventh Digit
Factory code
Last two digits of year produced
Week # of year produced
Revision level of the latest Engineering BOM
Factory Code
A - Samjin
D - Kimex
E - WKK
G - Computime
J - Jetta
K - Jeckson
M - Philips Mexico
N - Sejin
P - Philips Singapore
S - SMK Mexico
U - Universal Electronics
Example:
Factory:
Year:
Week:
BOM Rev.:
7.7.2
U001002
Universal Electronics
2000
10
02
Part Number Label
All assembly units require a label with the appropriate URC number applied inside the battery
compartment, unless this URC number has been printed on the battery cover door per submitted
artwork.
7.7.3
Country of Origin
All assembly units require country of origin either embossed or printed on bottom case or battery
door (except units shipped to Europe).
Viewsonic Tweety RF Remote
Universal Electronics Inc. Confidential
Rev 2.9A
November 05, 2001
Page 52 of 63
8 QUALITY
This section defines the appearance, cosmetic, and durability testing requirements for
plastic parts and assemblies, on all universal remote controls. However, when UEI
customer requirements mandate, stricter (tighter) evaluation and testing methods must be
used by the factory.
8.1
Appearance
The unit shall be constructed in accordance with the mechanical requirements set
forth in this section. These requirements must not be changed without written
approval of Universal Electronics Inc.
•
•
•
•
8.2
Key height shall be from 1.8±0.2 mm above the surface of the plastic case
when in a static condition.
The gap between key and plastic opening shall be 0.1mm minimum and
0.5mm maximum. (Suggested nominal gap 0.3 mm).
The plastic cases shall mate accurately with minimal overhang. The
maximum allowable overhang from the top case to the bottom case is 0.2mm.
The maximum allowable overhang from the bottom case to the top case is
0.1mm.
The plastic cases shall mate with a consistence gap around the peripheral.
The gap shall be within 0.2mm from its designed dimension.
Cosmetic
8.2.1 Evaluation Criteria
8.2.1.1 Evaluation Criteria
• Lighting to be directly overhead.
• Surface to be evaluated held at a 45° angle to the line of sight, at a distance of
51cm (20”) maximum to the center of surface.
• Unit under evaluation to be rotated 30° in both directions about the 45° inclined
axis.
8.2.1.2 Lighting
The light source shall be Cool White Fluorescent, non-directional at an
intensity of 1000±215 Lux (100±20 footcandles).
Viewsonic Tweety RF Remote
Universal Electronics Inc. Confidential
Rev 2.9A
November 05, 2001
Page 53 of 63
8.2.2 Definition of Flaw and Defect
The cosmetic features are divided into two categories: Flaws and Defects
1) Flaw is an acceptable imperfection or blemish.
2) Defect is a flaw that exceeds the cosmetic limit.
8.2.3
Definition of Classes
Class I :
Class II:
Class III:
The area usually viewed by user.
The area occasionally viewed by user.
The area seldom viewed by user.
Class II
Class II
Class II
Class I
Class III
Class II
Fi gure 2: D efiniti on of Classes
Viewsonic Tweety RF Remote
Universal Electronics Inc. Confidential
Rev 2.9A
November 05, 2001
Page 54 of 63
8.2.4
Cosmetic Evaluation
Part must not be "pre-inspected" at a distance closer than that allowed in the Viewing Angle and
Distance criteria.
8.2.4.1 All Classes
General:
Blush marks, burns, pits, pulling, short shot, silver-streaks, slay, and weldlines
are not acceptable.
Cleanliness:
Part must be free of dust, oil, grime, grease, and other contaminants. Dust
caused by shipping material is acceptable if it can be blown off by air or wiped
off.
8.2.4.2 Class I- Acceptable Flaws table
Maximum Inspection Time: 10 seconds
Type
Size
Qty
Parting Line Flash
0.15mm
Key Opening Flash
0.05mm
per opening
Mismatch
0.15mm
Scratches (within texture depth)
1.5x0.2mm
Contamination
0.5mm
Sink
not allowed
8.2.4.3 Class II- Acceptable Flaws table
Maximum Inspection Time: 5 seconds
Type
Size
Qty
Parting Line Flash
0.15mm
Mismatch
0.15mm
Scratches
2.0x0.2x0.3mm
Contamination
0.8mm
Sink
0.2mm
Viewsonic Tweety RF Remote
Universal Electronics Inc. Confidential
Rev 2.9A
November 05, 2001
Page 55 of 63
8.2.4.4 Class III- Acceptable Flaws table
Maximum Inspection Time: 5 seconds
Type
Size
Qty
Parting Line Flash
0.15mm
Mismatch
0.15mm
Scratches
3.0x0.2x0.4mm
Contamination
1.0mm
Sink
0.5mm
8.2.4.5 Defects
•
•
•
8.3
8.3.1
Any flaw that exceeds the limit of the above flaw table is a defect.
Any two flaws on a given surface closer than 25mm is a defect.
No more than three types of flaws are allowed on any one surface.
Durability Testing
Structure and Strength
•
•
•
•
•
The plastic parts shall withstand a 5 kg compressive force for 3 seconds at several points
without any physical damage by using a Slimline force gauge McMaster P/N 1365T24 (See
Appendix, Figure C).
The plastic parts shall withstand a bending force of 3 kg for 3 seconds applied at the ends of
the plastic assembly by using a Slimline force gauge McMaster P/N 1365T24 (See Appendix,
Figure D).
The keypad buttons shall withstand a 3kg over activation load vertically for 3 seconds by
using a Slimline force gauge McMaster P/N 1365T24 (See Appendix, Figure E).
The base of the keypad must not be exposed from the key opening after the 1.5kg lateral force
is applied by using a Slimline force gauge McMaster P/N 1365T24 (See Appendix, Figure F).
The keypad shall not be damaged in normal operation using pen, pencil, or fingernail.
8.3.2 Printing
•
•
•
All text printed on plastic surfaces or switch buttons must withstand normal shipping and
handling.
All printed legends must pass the Scotch Super strength packaging tape (3M cat no. 3506) test.
Scotch tape is applied on the test surface and then removed three times at a 45° angle (each
time a new tape). The printing shall not exhibit evident defects such as flaking, chipping,
blistering, or de-lamination.
All printed legends on plastic surfaces and keypad must be readable after being subjected to
500 cycles of abrasion @ 500 gram load with standard 100% cotton cloth as test piece.
Viewsonic Tweety RF Remote
Universal Electronics Inc. Confidential
Rev 2.9A
November 05, 2001
Page 56 of 63
8.3.3
Battery Contact
•
•
•
8.3.4
All forms of battery contacts, such as coiled spring and stamped spring, must not be
permanently deformed after the drop test.
The batteries must remain in contact after being inserted/removed 20 times.
The battery door must maintain its closing/latch integrity after being inserted/removed 20
times.
Painting wear test (if necessary)
The base plastic material cannot be shown after being subjected to 2000 cycles of abrasion @ 500
gram load with standard STAEDTLER eraser as test piece.
8.3.5
Rubber coating wear test (if necessary)
The base plastic material cannot be shown after being subjected to 2000 cycles of abrasion @ 500
gram load with standard STAEDTLER eraser as test piece.
8.3.6
Epoxy key test
8.3.6.1 Reliability tests
•
Adhesion test (see Figure G):
The key with epoxy top will be cut 1mm between the epoxy top and silicon rubber, then
peeled off by finger. More than 50% of silicon must be attached to the epoxy top.
•
Impact resistance test (see Figure H):
At room temperature, a 1.5-kg load will be dropped vertically onto the epoxy surface from
50cm high. There should be no visible crack or delamination.
•
Ultra-violet resistance test:
The key with epoxy top will be tested per ASTM–D1148 method B for 2 hours. There
should be no sign of de-laminating, cracking or discoloration.
•
Heat resistance test:
After the test-piece is exposed to 100°C for 12 hours, there should be no change of
transparency and color.
•
Lateral load test (see Figure J):
There should be no delamination between the epoxy and the rubber key when 2-kg lateral
load at any point on the epoxy and rubber key common edge.
•
Life test:
The key with epoxy encapsulated will be tested for 500,000 cycles with 250 grams force at 120 cycles
per minute. There should be no visible delamination.
Viewsonic Tweety RF Remote
Universal Electronics Inc. Confidential
Rev 2.9A
November 05, 2001
Page 57 of 63
8.3.6.2 Cosmetic tests
See Section 6.2.1.
1.
There should be no overflow larger than 0.15mm, and void (bubble) larger than
0.04mm.
2.
There should be no visible scratch, crack, cloudy (milky) spot, foreign objects
such as fiber, dust, etc.
Viewsonic Tweety RF Remote
Universal Electronics Inc. Confidential
Rev 2.9A
November 05, 2001
Page 58 of 63
9 ENVIRONMENTAL & SHOCK REQUIREMENTS
9.1
Temperature
Operating range:
0°C to +50°C
Non-operating range:
-10°C to +60°C
9.2
Humidity Test
The unit under evaluation will be exposed to 40±3°C, 95% relative humidity, noncondensing for 24 hours without batteries or power. Functional tests will be performed
after the HRC has stabilized at normal room conditions for two hours.
9.3
Low Temperature Test
The unit under evaluation will be exposed to -20±3°C for 24 hours without batteries or
power. Functional tests will be performed after the HRC has stabilized at normal room
conditions for two hours.
9.4
High Temperature Test
The unit under evaluation will be exposed to 60±3°C for 24 hours without batteries or
power. Functional tests will be performed after the HRC has stabilized at normal room
conditions for two hours.
Viewsonic Tweety RF Remote
Universal Electronics Inc. Confidential
Rev 2.9A
November 05, 2001
Page 59 of 63
9.5
Thermal Shock
The unit under evaluation (no batteries or power) will be subjected from -20°C to 60°C
for 5 cycles with a dwell time of 1 hour at high and low temperature (as shown below).
Functional tests will be performed after the HRC has stabilized at normal room
conditions for two hours.
9.6
Drop Test
The unit under evaluation must withstand one drop from 36 inches on six surfaces and
four corners onto hardwood flooring (suggested 0.75" thick oak). For further
specification details, see UEI Spec. #0005-0005.
For a product with three batteries or less, the battery door and batteries should not be
dislodged during the test.
Viewsonic Tweety RF Remote
Universal Electronics Inc. Confidential
Rev 2.9A
November 05, 2001
Page 60 of 63
9.7
Solvent Resistance
The unit under evaluation shall not be deformed or disfigured in any way by the
application of 409 All Purpose Cleaner with 0.3% Alkyl dimethyl benzyl ammonium
chloride or Windex with Ammonia-D to any exposed surfaces. Caustic solvents and
cleaners such as porcelain, stainless, toilet or oven cleaners shall not be used. Apply two
(2) sprays of the cleaner directly onto any surface. The unit is then cleaned by wet towel
after five (5) minutes drying.
9.8
Liquid Spill
Eight (8) ounces of black coffee (no sugar added) will be poured over the keypad area
at an angle of 30 degrees inclined (normal remote holding position). The unit with
batteries installed is then turned up side down for five (5) seconds to allow coffee to
drip off. The test sample must function properly after 48 hours stabilization.
Viewsonic Tweety RF Remote
Universal Electronics Inc. Confidential
Rev 2.9A
November 05, 2001
Page 61 of 63
10 Standard Compliances
10.1 ESD Protection
The HRC shall meet the following ESD profile per UEI Specification 0020 based on IEC 801-2.
10.2 FCC
Optoma will certify the complete unit with remote and keyboard.
With documentation and possible engineering support to Optoma from UEI.
Viewsonic Tweety RF Remote
Universal Electronics Inc. Confidential
Rev 2.9A
November 05, 2001
Page 62 of 63
11 Rendering
Viewsonic Tweety RF Remote
Universal Electronics Inc. Confidential
Rev 2.9A
November 05, 2001
Page 63 of 63
INSTRUCTIONS
MANUAL
FEDERAL COMMUNICATIONS COMMISSION
INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following
measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the euipment into an outlet on a circuir different from that to
which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
CAUTION:
Any changes or modifications not expressly approved by the grantee of
his device could void the user's authority to operate the equipment.
The antenna(s) used for this transmitter must be installed to provide a separation
distance of at least 20 cm from all persons and must not be co-located or operating in
conjunction with any other antenna or transmitter. End-users and installers must be
provided with antenna installation instructions and transmitter operating conditions for
satisfying RF exposure compliance

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Create Date                     : 2001:12:10 07:52:12Z
Modify Date                     : 2001:12:13 10:31:14+08:00
Page Count                      : 64
Creation Date                   : 2001:12:10 07:52:12Z
Mod Date                        : 2001:12:13 10:31:14+08:00
Producer                        : Acrobat Distiller 5.0 (Windows)
Author                          : kim
Metadata Date                   : 2001:12:13 10:31:14+08:00
Creator                         : kim
Title                           : Microsoft Word - ViewSonic Tweety RF RemoteRev2.91-QuieTek
Has XFA                         : No

EXIF Metadata provided by EXIF.tools

Universal Electronics 4012 ViewSonic Tweety RF Remote Control User Manual users manual

Universal Electronics Inc ViewSonic Tweety RF Remote Control users manual

users manual

FCC ID Filing: MG3-4012

Navigation menu

Namespaces

Views

Navigation