VALEO Telematik und Akustik PNADA GSM/GPRS/UMTS/HSDPA/HSUPA Module User Manual V1082 x13 UserManual Rev4

Peiker acustic GmbH & Co. KG GSM/GPRS/UMTS/HSDPA/HSUPA Module V1082 x13 UserManual Rev4

UserManual.wiki >

VALEO Telematik und Akustik >

PNADA User Manual

User Manual

_______________________________________________________________________________________________________________ Seite 1 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe User manual NAD-MDM6200 Peiker product #: 2189-082-112-00 (V1082-x13) HW0811 Revision: 0.4 Date: 10-2011 Status: Approved

_______________________________________________________________________________________________________________ Seite 2 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe History: Date Revision Name Comment 05.02.11 Rev 0.0 ChZi Initial document 08-08-2011 Rev 0.1 Gleich / Herold Document Review 17-08-2011 Rev 0.2 Hofmann Document Review 18-08-2011 Rev 0.3 Herold / Hofmann Document Review; Warning Statement included 06-10-2011 Rev. 0.4 Herold IC Canada Conformance statement Review

_______________________________________________________________________________________________________________ Seite 3 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe Content 1 Introduction .......................................................................................................................................... 4 1.1 Scope .................................................................................................................................................. 4 1.2 Audience ............................................................................................................................................ 4 1.3 Contact information, Support ......................................................................................................... 4 1.4 Related Documents .......................................................................................................................... 4 2 Overview ............................................................................................................................................... 4 2.1 Product Variants................................................................................................................................ 4 2.3 Features ............................................................................................................................................. 5 2.4 Approvals ........................................................................................................................................... 5 3 Overview ............................................................................................................................................... 6 3.1 Dimension, Mechanical Drawings ................................................................................................... 6 3.2 Block Diagram ................................................................................................................................... 7 3.3 HW Features ...................................................................................................................................... 7 3.4 Connectors ......................................................................................................................................... 8 3.4.1 Base Band Connector ............................................................................................................... 8 3.4.1 Antenna Connectors ................................................................................................................. 8 3.5 Interfaces (40pin Connector).......................................................................................................... 8 3.5.1 USB .............................................................................................................................................. 8 3.5.2 SIM Interface ............................................................................................................................. 8 3.5.3 KPD_POWER .............................................................................................................................. 9 3.5.4 Reset ........................................................................................................................................... 9 3.5.5 Reference Voltage Output (VREG_MSME 1.8V) ................................................................... 9 3.5.6 GPIOs .......................................................................................................................................... 9 3.5.7 GSBIs ........................................................................................................................................... 9 3.5.8 Baseband Connector Pinning ................................................................................................. 11 3.5.7 GPS related Pins ...................................................................................................................... 12 3.5.7 Antenna Diagnostics ............................................................................................................... 12 3.5.7 Antenna Switching .................................................................................................................. 13 3.6 Supply Voltage ................................................................................................................................ 13 3.7 Power Consumption ....................................................................................................................... 14 3.8 Transmitter ...................................................................................................................................... 14 3.9 Receiver ........................................................................................................................................... 14 3.10 Enviromental Specification .......................................................................................................... 14 3.10.1 Temperature Range .............................................................................................................. 14 4 Evaluation Kit ..................................................................................................................................... 16 5 AT Command interface ..................................................................................................................... 18 6 Safety Recommendations ................................................................................................................. 19 7 List of Acronyms ................................................................................................................................ 20 8 Warning Statements ......................................................................................................................... 21

_______________________________________________________________________________________________________________ Seite 4 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 1 Introduction 1.1 Scope This document give an overview electrical and functional detail fort he peiker NAD. 1.2 Audience Informations for integrate the module in other applications. 1.3 Contact information, Support Peiker Max-Planck Street 32 D-61381 Friedrichsdorf http://www.peiker.de info@peiker.de 1.4 Related Documents None. 2 Overview 2.1 Product Variants The NAD-MDM6200 ist available in 3 variants: Peiker product # WCDMA FDD bands 2189-082-112-00 (V1082-112) HW0811 BC1, BC8 (EU configuration) 2189-082-114-00 (V1082-114) HW0811 BC1 (China configuration) 2189-082-115-00 (V1082-x13) HW0811 BC2, BC5 (US2 configuration) All variants include Quad band GSM/GPRS/EDGE (850,900,1800,1900)

_______________________________________________________________________________________________________________ Seite 5 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 2.3 Features - GSM/GPRS/EDGE Quad band (850, 900, 1800,1900) - HSUPA up to 5.76 Mbps - HSDPA up to 14.4 Mbps - WCDMA up to 384kbps uplink/downlink - DTM - eCall inband nodem Power Classes - Class 4 (33dBm, 2W) Lo bands 850, 900 GSMK - Class 1 (30dBm, 1W) Hi bands 1800, 1900 GSMK - Class E2 Lo bands 850, 900 8PSK (EDGE) - Class E2 Hi bands 1800, 1900 8PSK (EDGE) - PS GPRS/EDGE Multi slot class 12 (4Dn/4Up/5Sum max.) - CS Multi slot class 1 (1Dn/1Up) - DTM Multi slot class 11 (4Dn/3Up/5Sum max.) 2.4 Approvals - R&TTE directive - CE, GCF - FCC, IC, PTCRB - AT&T

_______________________________________________________________________________________________________________ Seite 6 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 3 Overview 3.1 Dimension, Mechanical Drawings Figure 1 V1082-x13 Mechanical Dimensions. Figure 2 V1082-x13 Mechanical Dimensions (Top View).

_______________________________________________________________________________________________________________ Seite 7 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 3.2 Block Diagram Figure 3 V1082-x13 Block Diagram. 3.3 HW Features - Qualcomm chipset MDM6200 (RF + Base band) + PM8028 (Power management) - ARM11 Core up to 480 MHz - 2 DSP for modem and application DSP - MCP Memory (1Gb NAND Flash x16, 512Mb Mobile DDR SDRAM x16) - 19.2MHz clock reference - SPDT switch for main and backup antenna operation - Onboard antenna diagnostic - Heavy duty baseband and antenna connector - Dedicated heat sink area under power amplifier section - Prepared for GPS/Glonass operation, GPS antenna biasing and diagnostics

_______________________________________________________________________________________________________________ Seite 8 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 3.4 Connectors 3.4.1 Base Band Connector The NAD has a 40pin (2x20) connector with 1.27mm pitch. The connector is designed to stitch through the main board PCB. To allow variable mounting scenarios the 40pin connect can be populated on the top or the bottom side of NAD PCB. Default location is the PCB bottom side. 3.4.1 Antenna Connectors To support the usage of a main and backup antenna, the NAD has an automotive dual FAKRA RF- Connector (SMB male) populated. The NAD board is prepared for the population of another single FAKRA RF- RF- Connector (SMB male) to connect a GPS/GLONASS active antenne for simultaneous GPS/GLONASS operation 3.5 Interfaces (40pin Connector) 3.5.1 USB The NAD has one USB2.0 OTG high speed (480MBit) compliant interface including the phy. The IF consists of 4 signals: USB_DP USB_DM USB_VBUS USB_GND A dynamic reconfiguration between USB-Host or USB-Device is not foreseen, the NAD can be configured to USB-Host or USB-Device by the insertion of a resistor on the NAD PCB. 3.5.2 SIM Interface The NADs SIM interface is compatible to 1.8V and 3V SIM Cards, the nessecary voltage and level shifting is handle by NAD automatically. The IF Consists of the following signals: VREG_USIM USIM_CLK USIM_DATA USIM_RESET The data speed on the SIM IF is up to 4 MBit, so HW designers should take care of the length and routing of the SIM IF to prevent potential EMC problems.

_______________________________________________________________________________________________________________ Seite 9 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 3.5.3 KPD_POWER The signal is used switch on the NAD-Module. KPD_POWER is pulled against VPH_Power on the NAD internally. Due to this fact it is recommended to pull this input against GND using an open collector or open drain output only. 3.5.4 Reset The signal is used to reset the NAD the NAD-Module. RES_IN is pulled against VPH_Power on the NAD internally. Due to this fact it is recommended to pull this input against GND using an open collector or open drain output only. 3.5.5 Reference Voltage Output (VREG_MSME 1.8V) VREG_MSME is the reference voltage corresponding to the GPIOs/GSBI interfaces of NAD. VREG_MSME can be used to source interface circuits like level shifters which are connected to the GPIOs/GSBIs of the NAD. The current on VREG_MSME shall not exceed 30mA. When using VREG_MSME it is recommended to to decouple the signal with a combination of 1uF and 22pF directly at the baseband connector. 3.5.6 GPIOs 21 GPIOs are available on NAD baseband connector. The reference voltage is of the GPIOs is 1.8V. The GPIOs can be used with flexible input and out configurations, such input with pull up or pull down, various pull up/down drive strength can be programmed interrupt functionality is possible. Also output push/pull or output with pull/down can be configured. For details please refer to latest chipset device specification document 80_VR001-1. Some the GPIOs are part of the 5 available GSBIs (General Serial Bus Interface). GPIOs and GSBIs share the same output pins and may not available when used in an GSBI configuration, see chapter GSBIs. GPIOs not belonging to a GSBI bundle: GPIO9,14,17,69,73 GPIOs belonging to a GSBI bundle: GPIO30,31,32,33,34,35,36,37,38,39,40,41,42,43,46,47 3.5.7 GSBIs Each GSBI (General Serial Bus Interface) consists of a bundle of 4 GPIOs. 5 GSBI are available. The reference voltage is of the GSBIs is 1.8V. Available signals on GSBI bundles:

_______________________________________________________________________________________________________________ Seite 10 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe GSBI0: GSBI0_2, GSBI0_3 (GPIO_30,31) GSBI1: GSBI1_0, GSBI1_1, GSBI1_2, GSBI1_3 (GPIO_32,33,34,35) GSBI2: GSBI2_0, GSBI2_1, GSBI2_2, GSBI2_3 (GPIO_36,37,38,39) GSBI3: GSBI3_0, GSBI3_1, GSBI3_2, GSBI3_3 (GPIO_40,41,42,43) GSBI4: GSBI4_2, GSBI4_3 (GPIO_46,47) Generally the functions of a GSBI are: UART, UIM, I2C, I2S, SPI, PCM, RTS, CTS, GPIO For details and possible combinations an GSBIs please refer to latest chipset device specification document 80_VR001-1. An example of a possible configuration with I2S audio codec, I2C audio codec control and and 2 UARTS is shown below. For details also refer to V1102 schematics.

_______________________________________________________________________________________________________________ Seite 11 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 3.5.8 Baseband Connector Pinning Pin Signal Direction related to NAD Parameter Comment 2 GND Input Power Power GND 1 VPH_PWR Input Power 3.8V / 2A peak Main power 4 GND Input Power Power GND 3 VPH_PWR Input Power 3.8V / 2A peak Main power 6 GND Input Power Power GND 5 VPH_PWR Input Power 3.8V / 2A peak Main power 8 VREG_MSME Output Power 1,8V / 30mA Output power to TCB mainboard for sourcing levelshifters 7 KPD_POWER IN / active low pull down with o.C. NAD switch on input 10 USIM_CLK OUT 2.85V / 1.8V SIM-Card clock 9 USIM_RST OUT 2.85V / 1.8V SIM-Card reset 12 USIM_DATA I/O 2.85V / 1.8V SIM-Card data, requires a pull up to VREG_USIM @ destination platform 11 VREG_USIM Output Power 2.85V / 1.8V / 150mA Output power to SIM-Card 14 GPIO_69 I/O 1.8V GPIO 13 GPIO_73 I/O 1.8V GPIO 16 RES_IN IN pull down with o.C force a reset condition to NAD 15 GPIO_32_GSBI1_0 I/O 1.8V GPIO or GSBI 18 GPIO_33_GSBI1_1 I/O 1.8V GPIO or GSBI 17 GPIO_35_GSBI1_3 I/O 1.8V GPIO or GSBI 20 GPIO_34_GSBI1_2 I/O 1.8V GPIO or GSBI 19 GPIO_30_GSBI0_2 I/O 1.8V GPIO or GSBI 22 GPIO31_GSBI_0_3 I/O 1.8V GPIO or GSBI 21 GPIO_47_ OUT 1.8V GPIO or GSBI 24 USB_VBUS Input Power 5V / 5mA High-Speed USB Device for communication 23 USB_DP IN/OUT USB-Level 3.3V High-Speed USB Device for communication 26 GND_USB Power High-Speed USB Device for communication 25 USB_DM IN/OUT USB-Level 3.3V High-Speed USB Device for communication 28 GPIO_37_GSBI_2_1 I/O 1.8V GPIO or GSBI 27 GPIO_38_GSBI_2_2 I/O 1.8V GPIO or GSBI 30 GPIO_39_GSBI_2_3 I/O 1.8V GPIO or GSBI 29 GPIO_36_GSBI_2_0 I/O 1.8V GPIO or GSBI 32 GPIO_43_GSBI_3_3 I/O 1.8V GPIO or GSBI 31 GPIO_42_GSBI_3_2 I/O 1.8V GPIO or GSBI 34 GPIO_41_GSBI_3_1 I/O 1.8V GPIO or GSBI 33 GPIO_40_GSBI_3_0 I/O 1.8V GPIO or GSBI 36 GPIO_14 I/O 1.8V GPIO 35 GPIO_17 I/O 1.8V GPIO 38 GPIO_9 I/O 1.8V GPIO 37 GPIO_46_GSBI_4_2 I/O 1.8V GPIO or GSBI 40 EXT_5V5 Input Power 5,5V / 100mA Power for inside GPS-Antenna LNA 39 GPS_ANT_OVERVOLT OUT / active low Open Collector Detection of GPS-Antenna short against vehicle battery (8-18V)

_______________________________________________________________________________________________________________ Seite 12 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 3.5.7 GPS related Pins Pin 39 GPS_ANT_OVERVOLTAGE and Pin 40 EXT_5V5 are reserved for future use of the internal GPS of the NAD. The pins should be grounded when not used in the design. 3.5.7 Antenna Diagnostics The NAD is capable to monitor the connection status of both antennas (MAIN and BACKUP) To monitor the connection status, antennas with internal DC coupled 10k resistors to GND must be used. The diagnose is performed by NAD SW using 2 ADCs. The following connection states of the antenna can be monitored: - Antenna short against GND - Antenna short against Vbatt (+12V) - Antenna connected - Antenna not connected

_______________________________________________________________________________________________________________ Seite 13 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 3.5.7 Antenna Switching The NAD is equipped with to antenna connectors. A main and a backup antenna can be connected to the antenna ports. To switchover between the antennas a SPDT RF- Switch is populated on NAD. The switch can be performed by SW toggling 2 internal GPIOs on NAD. At the moment the main antenna is switched on by default. The main antenna is the mapped to the SMB connector close to the outer dimension of the NAD. SPDT Figure 4 V1082-x13 Antenna Connectors. 3.6 Supply Voltage The external supply voltage is apllied to NAD by 6 Pins on the base band connector. PINs 1,3,5 for VPH_PWR PINs 2,4,5 for the corresponding GND TA = -40°C … +85°C Absolute maximum supply voltage 3.4V ~ 4.2V Nominal supply voltage 3.8V Recommended supply voltage 3.7V ~ 3.9V Voltage drop @ GSM power burst (33dBm) <100mV Main Antenna Backup Antenna Antenna Prepared GPS Antenna connector Not populated

_______________________________________________________________________________________________________________ Seite 14 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe During Hi RF Power GSM bursts the power amplifier can draw peak currents > 2Amps at VPH_PWR. The voltage drop during the GSM burst shall not exceed 100mV (measured at C5 on the NAD module 3.7 Power Consumption TA = +25°C, VPH_PWR =3.8V Output Power Output Power max. (typ. 23dBm) 0 dBm Voice call WCDMA BC1 ~530mA ~145mA Voice call WCDMA BC2 ~570mA ~145mA Voice call WCDMA BC5 ~630mA ~140mA Voice call WCDMA BC8 ~580mA ~140mA PCL 5 (typ. 32.5 dBm) PCL 19 (typ. 5dBm) Voice call GSM850 ~260mA ~65mA Voice call GSM900 ~270mA ~65mA PCL 0 (typ.30.5dBm) PCL 15 (typ.0dBm) Voice call GSM1800 ~165mA ~65mA Voice call GSM1900 ~165mA ~65mA Standby current GSM DRX = 5 Tbd mA Standby current WCDMA DRX = 7 Tbd mA 3.8 Transmitter Tbd. 3.9 Receiver Tbd. 3.10 Enviromental Specification 3.10.1 Temperature Range Range Operating temp. range -20°C … +65°C 3GPP spec. conform Operating temp. range -25°C … +85°C Note 1 Operational Performance might slightly deviate from 3GPP spec. Storage temp. range -40°C … +85°C

_______________________________________________________________________________________________________________ Seite 15 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe Note 1: Due to temperature specification of the chipset, the temperature of the power manager and the temperature of the modem chip shall not excced +85°C.

_______________________________________________________________________________________________________________ Seite 16 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 4 Evaluation Kit For the NAD V1082-x13 there is an evaluation board available. Features : - On board 12V DC power supply or 3,8V DC direct connected (i.e. unbuffered). - USB port type B - SIM card tray - 40 pin header connected to the systemconnector of the NAD - 3 GSPI Port connected to DB9 or pin header. Can be configured as UART od SDIO or SPDIF to connect audio codecs Using the evaluation board with on board 3.8V regulator - Connect 11 .. 14V DC to power connector 1) (use delivered cable) - Power on the board with switch 2). Using the evaluation board with an external power supply - Remove Jumper 3) - Switch 2) to off condition - Connect external supply V+ 3.6 .. 4.0V DC to connector 4) (nominal 3.8V DC) - Connector 4): Pin1: GND Pin2: Sense GND Pin3: Sense V+ Pin4: V+ Note: Make sure that the external power supply is not generating spikes or hazards higher than 4.2V. NAD Module gets damaged when spikes or hazards above 4.2V are applied RF Connector - For RF measurements use main antenna connector 5)

_______________________________________________________________________________________________________________ Seite 17 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe Figure 5 Evaluation Kit for V1082-x13.

_______________________________________________________________________________________________________________ Seite 19 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe Command Description Comment ATE Character Echo ON/OFF AT+CSMS Check Message Service support AT+CSMP Set Text Mode Parameters AT+CSDH Show Text Mode Parameters AT+CSCB Select Cell Broadcast Message Types AT+CSAS Save Settings Only one Parameter is supported by the device. AT+CRES Restore Settings Only one Parameter is supported by the device. AT+CMGL List messages AT+CNMA New message acknowledgement AT+CMGC Send Command AT+CMMS More Messages to Send AT+ATV DCE response format AT+ATX Result code selection and call progress monitoring control AT+CNMI New Message Indications to TE AT+CPMS Preferred Message Storage AT+CMGW Write Message to Memory AT+CMSS Send Message from Storage AT+CMGD Delete Messages AT+CNUM Get MSISDN AT+CPBS Select phonebook memory storage AT+CPBR Read phonebook entries AT+CPBW Writephonebook entry 6 Safety Recommendations Tbd.

_______________________________________________________________________________________________________________ Seite 20 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 7 List of Acronyms 3GPP 3 rd Generation Partnership Project ADC Analog Digital Converter ADN Abbrieviated Dialing Number A-GPS Assisted GPS AMR Adaptive Multi Rate AT Attention Command AWS Advanced Wireless Services BER Bit Error Rate CLIP Calling Line Identification Presentation CLIR Calling Line Identification Restriction CSD Circuit Switch Data DARP Downlink Advanced Receiver Performance DTMF Dual Tone Multi Frequency FDN Fixed Dialing Number FTP File Transfer Protocol GSM Global System for Mobile communication GPIO General Purpose Input Output GPRS General Packet Radio Service GPS Global Positioning Systen HSPA High Speed Uplink Pachet Access HW Hardware LED Led Emitting Diode MO Mobile Originated MT Mobile Terminated OEM Original Equipment Manufacturer PCB Printed Circuit Board PCM Pulse Code Modulation PDU Protocol Data Unit PIN Personal Identification Number RF Radio Frequency RoHs Restriction of Hazardous Substances UART Universal Asynchronous Receiver and Transmitter USB Universal Serial Bus USIM Universal Subscriber Identity Module UMTS Universal Mobile Telecommunications System WCDMA Wideband Code Division Multiple Access

_______________________________________________________________________________________________________________ Seite 21 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 8 Warning Statements FCC NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. (c) The provisions of paragraphs (a) and (b) of this section do not apply to digital devices exempted from the technical standards under the provisions of § 15.103. (d) For systems incorporating several digital devices, the statement shown in paragraph (a) or (b) of this section needs to be contained only in the instruction manual for the main control unit. (e) In cases where the manual is provided only in a form other than paper, such as on a computer disk or over the Internet, the information required by this section may be included in the manual in that alternative form, provided the user can reasonably be expected to have the capability to access information in that form. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IC Canada This Class b digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe b est conforme à la norme NMB-003 du Canada.

_______________________________________________________________________________________________________________ Seite 22 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Modifications The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by peiker acustic GmbH & Co. KG could void the user's authority to operate the equipment.

Navigation menu