VALEO Telematik und Akustik PNADA GSM/GPRS/UMTS/HSDPA/HSUPA Module User Manual V1082 x13 UserManual Rev4
Peiker acustic GmbH & Co. KG GSM/GPRS/UMTS/HSDPA/HSUPA Module V1082 x13 UserManual Rev4
User Manual
User manual NAD-MDM6200 Peiker product #: 2189-082-112-00 (V1082-x13) HW0811 Revision: Date: 0.4 10-2011 Status: Approved _______________________________________________________________________________________________________________ Seite 1 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe History: Date 05.02.11 08-082011 17-082011 18-082011 06-102011 Revision Rev 0.0 Rev 0.1 Rev 0.2 Rev 0.3 Rev. 0.4 Name ChZi Gleich / Herold Hofmann Comment Initial document Document Review Document Review Herold / Document Review; Warning Statement included Hofmann Herold IC Canada Conformance statement Review _______________________________________________________________________________________________________________ Seite 2 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe Content Introduction .......................................................................................................................................... 4 1.1 Scope .................................................................................................................................................. 4 1.2 Audience ............................................................................................................................................ 4 1.3 Contact information, Support ......................................................................................................... 4 1.4 Related Documents .......................................................................................................................... 4 Overview ............................................................................................................................................... 4 2.1 Product Variants................................................................................................................................ 4 2.3 Features ............................................................................................................................................. 5 2.4 Approvals ........................................................................................................................................... 5 Overview ............................................................................................................................................... 6 3.1 Dimension, Mechanical Drawings................................................................................................... 6 3.2 Block Diagram ................................................................................................................................... 7 3.3 HW Features ...................................................................................................................................... 7 3.4 Connectors ......................................................................................................................................... 8 3.4.1 Base Band Connector ............................................................................................................... 8 3.4.1 Antenna Connectors ................................................................................................................. 8 3.5 Interfaces (40pin Connector).......................................................................................................... 8 3.5.1 USB .............................................................................................................................................. 8 3.5.2 SIM Interface ............................................................................................................................. 8 3.5.3 KPD_POWER .............................................................................................................................. 9 3.5.4 Reset ........................................................................................................................................... 9 3.5.5 Reference Voltage Output (VREG_MSME 1.8V) ................................................................... 9 3.5.6 GPIOs .......................................................................................................................................... 9 3.5.7 GSBIs........................................................................................................................................... 9 3.5.8 Baseband Connector Pinning................................................................................................. 11 3.5.7 GPS related Pins ...................................................................................................................... 12 3.5.7 Antenna Diagnostics ............................................................................................................... 12 3.5.7 Antenna Switching .................................................................................................................. 13 3.6 Supply Voltage ................................................................................................................................ 13 3.7 Power Consumption ....................................................................................................................... 14 3.8 Transmitter ...................................................................................................................................... 14 3.9 Receiver ........................................................................................................................................... 14 3.10 Enviromental Specification .......................................................................................................... 14 3.10.1 Temperature Range .............................................................................................................. 14 Evaluation Kit ..................................................................................................................................... 16 AT Command interface ..................................................................................................................... 18 Safety Recommendations................................................................................................................. 19 List of Acronyms ................................................................................................................................ 20 Warning Statements ......................................................................................................................... 21 _______________________________________________________________________________________________________________ Seite 3 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 1 Introduction 1.1 Scope This document give an overview electrical and functional detail fort he peiker NAD. 1.2 Audience Informations for integrate the module in other applications. 1.3 Contact information, Support Peiker Max-Planck Street 32 D-61381 Friedrichsdorf http://www.peiker.de info@peiker.de 1.4 Related Documents None. Overview 2.1 Product Variants The NAD-MDM6200 ist available in 3 variants: Peiker product # WCDMA FDD bands 2189-082-112-00 (V1082-112) HW0811 2189-082-114-00 (V1082-114) HW0811 2189-082-115-00 (V1082-x13) HW0811 BC1, BC8 (EU configuration) BC1 (China configuration) BC2, BC5 (US2 configuration) All variants include Quad band GSM/GPRS/EDGE (850,900,1800,1900) _______________________________________________________________________________________________________________ Seite 4 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 2.3 Features GSM/GPRS/EDGE Quad band (850, 900, 1800,1900) HSUPA up to 5.76 Mbps HSDPA up to 14.4 Mbps WCDMA up to 384kbps uplink/downlink DTM eCall inband nodem Power Classes Class 4 (33dBm, 2W) Lo bands 850, 900 GSMK Class 1 (30dBm, 1W) Hi bands 1800, 1900 GSMK Class E2 Lo bands 850, 900 8PSK (EDGE) Class E2 Hi bands 1800, 1900 8PSK (EDGE) PS GPRS/EDGE Multi slot class 12 (4Dn/4Up/5Sum max.) CS Multi slot class 1 (1Dn/1Up) DTM Multi slot class 11 (4Dn/3Up/5Sum max.) 2.4 Approvals R&TTE directive CE, GCF FCC, IC, PTCRB AT&T _______________________________________________________________________________________________________________ Seite 5 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 3 Overview 3.1 Dimension, Mechanical Drawings Figure 1 V1082-x13 Mechanical Dimensions. Figure 2 V1082-x13 Mechanical Dimensions (Top View). _______________________________________________________________________________________________________________ Seite 6 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 3.2 Block Diagram Figure 3 V1082-x13 Block Diagram. 3.3 HW Features Qualcomm chipset MDM6200 (RF + Base band) + PM8028 (Power management) ARM11 Core up to 480 MHz 2 DSP for modem and application DSP MCP Memory (1Gb NAND Flash x16, 512Mb Mobile DDR SDRAM x16) 19.2MHz clock reference SPDT switch for main and backup antenna operation Onboard antenna diagnostic Heavy duty baseband and antenna connector Dedicated heat sink area under power amplifier section Prepared for GPS/Glonass operation, GPS antenna biasing and diagnostics _______________________________________________________________________________________________________________ Seite 7 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 3.4 Connectors 3.4.1 Base Band Connector The NAD has a 40pin (2x20) connector with 1.27mm pitch. The connector is designed to stitch through the main board PCB. To allow variable mounting scenarios the 40pin connect can be populated on the top or the bottom side of NAD PCB. Default location is the PCB bottom side. 3.4.1 Antenna Connectors To support the usage of a main and backup antenna, the NAD has an automotive dual FAKRA RFConnector (SMB male) populated. The NAD board is prepared for the population of another single FAKRA RF- RF- Connector (SMB male) to connect a GPS/GLONASS active antenne for simultaneous GPS/GLONASS operation 3.5 Interfaces (40pin Connector) 3.5.1 USB The NAD has one USB2.0 OTG high speed (480MBit) compliant interface including the phy. The IF consists of 4 signals: USB_DP USB_DM USB_VBUS USB_GND A dynamic reconfiguration between USB-Host or USB-Device is not foreseen, the NAD can be configured to USB-Host or USB-Device by the insertion of a resistor on the NAD PCB. 3.5.2 SIM Interface The NADs SIM interface is compatible to 1.8V and 3V SIM Cards, the nessecary voltage and level shifting is handle by NAD automatically. The IF Consists of the following signals: VREG_USIM USIM_CLK USIM_DATA USIM_RESET The data speed on the SIM IF is up to 4 MBit, so HW designers should take care of the length and routing of the SIM IF to prevent potential EMC problems. _______________________________________________________________________________________________________________ Seite 8 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 3.5.3 KPD_POWER The signal is used switch on the NAD-Module. KPD_POWER is pulled against VPH_Power on the NAD internally. Due to this fact it is recommended to pull this input against GND using an open collector or open drain output only. 3.5.4 Reset The signal is used to reset the NAD the NAD-Module. RES_IN is pulled against VPH_Power on the NAD internally. Due to this fact it is recommended to pull this input against GND using an open collector or open drain output only. 3.5.5 Reference Voltage Output (VREG_MSME 1.8V) VREG_MSME is the reference voltage corresponding to the GPIOs/GSBI interfaces of NAD. VREG_MSME can be used to source interface circuits like level shifters which are connected to the GPIOs/GSBIs of the NAD. The current on VREG_MSME shall not exceed 30mA. When using VREG_MSME it is recommended to to decouple the signal with a combination of 1uF and 22pF directly at the baseband connector. 3.5.6 GPIOs 21 GPIOs are available on NAD baseband connector. The reference voltage is of the GPIOs is 1.8V. The GPIOs can be used with flexible input and out configurations, such input with pull up or pull down, various pull up/down drive strength can be programmed interrupt functionality is possible. Also output push/pull or output with pull/down can be configured. For details please refer to latest chipset device specification document 80_VR001-1. Some the GPIOs are part of the 5 available GSBIs (General Serial Bus Interface). GPIOs and GSBIs share the same output pins and may not available when used in an GSBI configuration, see chapter GSBIs. GPIOs not belonging to a GSBI bundle: GPIO9,14,17,69,73 GPIOs belonging to a GSBI bundle: GPIO30,31,32,33,34,35,36,37,38,39,40,41,42,43,46,47 3.5.7 GSBIs Each GSBI (General Serial Bus Interface) consists of a bundle of 4 GPIOs. 5 GSBI are available. The reference voltage is of the GSBIs is 1.8V. Available signals on GSBI bundles: _______________________________________________________________________________________________________________ Seite 9 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe GSBI0: GSBI1: GSBI2: GSBI3: GSBI4: GSBI0_2, GSBI1_0, GSBI2_0, GSBI3_0, GSBI4_2, GSBI0_3 (GPIO_30,31) GSBI1_1, GSBI1_2, GSBI1_3 (GPIO_32,33,34,35) GSBI2_1, GSBI2_2, GSBI2_3 (GPIO_36,37,38,39) GSBI3_1, GSBI3_2, GSBI3_3 (GPIO_40,41,42,43) GSBI4_3 (GPIO_46,47) Generally the functions of a GSBI are: UART, UIM, I2C, I2S, SPI, PCM, RTS, CTS, GPIO For details and possible combinations an GSBIs please refer to latest chipset device specification document 80_VR001-1. An example of a possible configuration with I2S audio codec, I2C audio codec control and and 2 UARTS is shown below. For details also refer to V1102 schematics. _______________________________________________________________________________________________________________ Seite 10 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 3.5.8 Baseband Connector Pinning Pin Signal GND VPH_PWR GND VPH_PWR GND VPH_PWR VREG_MSME Direction related to NAD Input Power Input Power Input Power Input Power Input Power Input Power Output Power 10 KPD_POWER USIM_CLK USIM_RST IN / active low OUT OUT 12 USIM_DATA I/O 11 14 13 16 15 18 17 20 19 22 21 24 23 26 25 28 27 30 29 32 31 34 33 36 35 38 37 40 VREG_USIM GPIO_69 GPIO_73 RES_IN GPIO_32_GSBI1_0 GPIO_33_GSBI1_1 GPIO_35_GSBI1_3 GPIO_34_GSBI1_2 GPIO_30_GSBI0_2 GPIO31_GSBI_0_3 GPIO_47_ USB_VBUS USB_DP GND_USB USB_DM GPIO_37_GSBI_2_1 GPIO_38_GSBI_2_2 GPIO_39_GSBI_2_3 GPIO_36_GSBI_2_0 GPIO_43_GSBI_3_3 GPIO_42_GSBI_3_2 GPIO_41_GSBI_3_1 GPIO_40_GSBI_3_0 GPIO_14 GPIO_17 GPIO_9 GPIO_46_GSBI_4_2 EXT_5V5 Output Power I/O I/O IN I/O I/O I/O I/O I/O 39 GPS_ANT_OVERVOLT I/O OUT Input Power IN/OUT Power IN/OUT I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O Input Power OUT / active low Parameter 3.8V / 2A peak 3.8V / 2A peak 3.8V / 2A peak 1,8V / 30mA pull down with o.C. 2.85V / 1.8V 2.85V / 1.8V 2.85V / 1.8V 2.85V / 1.8V / 150mA 1.8V 1.8V pull down with o.C 1.8V 1.8V 1.8V 1.8V 1.8V 1.8V 1.8V 5V / 5mA USB-Level 3.3V USB-Level 3.3V 1.8V 1.8V 1.8V 1.8V 1.8V 1.8V 1.8V 1.8V 1.8V 1.8V 1.8V 1.8V 5,5V / 100mA Open Collector Comment Power GND Main power Power GND Main power Power GND Main power Output power to TCB mainboard for sourcing levelshifters NAD switch on input SIM-Card clock SIM-Card reset SIM-Card data, requires a pull up to VREG_USIM @ destination platform Output power to SIM-Card GPIO GPIO force a reset condition to NAD GPIO or GSBI GPIO or GSBI GPIO or GSBI GPIO or GSBI GPIO or GSBI GPIO or GSBI GPIO or GSBI High-Speed USB High-Speed USB High-Speed USB High-Speed USB GPIO or GSBI GPIO or GSBI GPIO or GSBI GPIO or GSBI GPIO or GSBI GPIO or GSBI GPIO or GSBI GPIO or GSBI Device for Device for Device for Device for communication communication communication communication GPIO GPIO GPIO GPIO or GSBI Power for inside GPS-Antenna LNA Detection of GPS-Antenna short against vehicle battery (818V) _______________________________________________________________________________________________________________ Seite 11 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 3.5.7 GPS related Pins Pin 39 GPS_ANT_OVERVOLTAGE and Pin 40 EXT_5V5 are reserved for future use of the internal GPS of the NAD. The pins should be grounded when not used in the design. 3.5.7 Antenna Diagnostics The NAD is capable to monitor the connection status of both antennas (MAIN and BACKUP) To monitor the connection status, antennas with internal DC coupled 10k resistors to GND must be used. The diagnose is performed by NAD SW using 2 ADCs. The following connection states of the antenna can be monitored: - Antenna short against GND - Antenna short against Vbatt (+12V) - Antenna connected - Antenna not connected _______________________________________________________________________________________________________________ Seite 12 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 3.5.7 Antenna Switching The NAD is equipped with to antenna connectors. A main and a backup antenna can be connected to the antenna ports. To switchover between the antennas a SPDT RF- Switch is populated on NAD. The switch can be performed by SW toggling 2 internal GPIOs on NAD. At the moment the main antenna is switched on by default. The main antenna is the mapped to the SMB connector close to the outer dimension of the NAD. SPDT Main Antenna Backup Antenna Antenna Prepared GPS Antenna connector Not populated Figure 4 V1082-x13 Antenna Connectors. 3.6 Supply Voltage The external supply voltage is apllied to NAD by 6 Pins on the base band connector. PINs 1,3,5 for VPH_PWR PINs 2,4,5 for the corresponding GND TA = -40°C … +85°C Absolute maximum supply voltage Nominal supply voltage Recommended supply voltage Voltage drop @ GSM power burst (33dBm) 3.4V ~ 4.2V 3.8V 3.7V ~ 3.9V <100mV _______________________________________________________________________________________________________________ Seite 13 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe During Hi RF Power GSM bursts the power amplifier can draw peak currents > 2Amps at VPH_PWR. The voltage drop during the GSM burst shall not exceed 100mV (measured at C5 on the NAD module 3.7 Power Consumption TA = +25°C, VPH_PWR =3.8V Voice Voice Voice Voice call call call call WCDMA WCDMA WCDMA WCDMA BC1 BC2 BC5 BC8 Voice call GSM850 Voice call GSM900 Voice call GSM1800 Voice call GSM1900 Standby current GSM Standby current WCDMA Output Power max. (typ. 23dBm) ~530mA ~570mA ~630mA ~580mA Output Power 0 dBm ~145mA ~145mA ~140mA ~140mA PCL 5 (typ. 32.5 dBm) ~260mA ~270mA PCL 0 (typ.30.5dBm) ~165mA ~165mA PCL 19 (typ. 5dBm) ~65mA ~65mA PCL 15 (typ.0dBm) ~65mA ~65mA DRX = 5 DRX = 7 Tbd mA Tbd mA 3.8 Transmitter Tbd. 3.9 Receiver Tbd. 3.10 Enviromental Specification 3.10.1 Temperature Range Range Operating temp. range Operating temp. range -20°C … +65°C -25°C … +85°C Storage temp. range -40°C … +85°C Note 1 3GPP spec. conform Operational Performance might slightly deviate from 3GPP spec. _______________________________________________________________________________________________________________ Seite 14 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe Note 1: Due to temperature specification of the chipset, the temperature of the power manager and the temperature of the modem chip shall not excced +85°C. _______________________________________________________________________________________________________________ Seite 15 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 4 Evaluation Kit For the NAD V1082-x13 there is an evaluation board available. Features : - On board 12V DC power supply or 3,8V DC direct connected (i.e. unbuffered). - USB port type B - SIM card tray - 40 pin header connected to the systemconnector of the NAD - 3 GSPI Port connected to DB9 or pin header. Can be configured as UART od SDIO or SPDIF to connect audio codecs Using the evaluation board with on board 3.8V regulator Connect 11 .. 14V DC to power connector 1) (use delivered cable) Power on the board with switch 2). Using the evaluation board with an external power supply Remove Jumper 3) Switch 2) to off condition Connect external supply V+ 3.6 .. 4.0V DC to connector 4) (nominal 3.8V DC) Connector 4): Pin1: GND Pin2: Sense GND Pin3: Sense V+ Pin4: V+ Note: Make sure that the external power supply is not generating spikes or hazards higher than 4.2V. NAD Module gets damaged when spikes or hazards above 4.2V are applied RF Connector For RF measurements use main antenna connector 5) _______________________________________________________________________________________________________________ Seite 16 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe Figure 5 Evaluation Kit for V1082-x13. _______________________________________________________________________________________________________________ Seite 17 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 5 AT Command interface The modules supports standart AT command as listed below. Commands are compliant to 3GPP TS 27.007 . 3GPP TS 27.005 Command Description AT+CMGF AT+CSCA AT+CMGS AT+CGMI AT+CGMM AT+CGMR AT+CGSN Message Format Service Centre Address Send Message Manufacturer Identification Request model identification Request revision identification Request product serial number Request international mobile subscriber identification Call mode AT+CIMI AT+CMOD AT+CHUP ATD ATA ATH AT+CBST AT+CEER AT+CVHU AT+CREG AT+COPS AT+CLCK AT+CPWD AT+CLIP AT+CLIR AT+CCWA AT+CHLD AT+CUSD AT+CLCC AT+CPOL AT+CPAS AT+CFUN AT+CPIN AT+CSQ AT+CMER AT+CSIM AT+CRSM AT+CMEE AT+CGDCONT AT+CGEQREQ AT-CGATT AT+CGACT AT+CGPADDR AT+CGSMS Comment Only one Parameter is supported by the device. Hang up call Initiate a CS or PS call or supplementary service Answer incoming CS call command Hangup CS call command Select bearer service type Extended error report Voice hangup control Network registration PLMN selection Facility lock Change password Calling line identification presentation Calling line identification restriction Call waiting Call related supplementary services Unstructured supplementary service data List current calls Preferred PLMN list Phone active status Set phone functionality Enter PIN Signal quality Mobile termination event reporting Generic SIM access Restricted SIM access Report mobile termination error Define PDP context Request 3G quality of service profile PS attach or detach PDP context activate or deactivate Show PDP address Select service for MO SMS messages _______________________________________________________________________________________________________________ Seite 18 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe Command Description ATE Character Echo ON/OFF AT+CSMS AT+CSMP AT+CSDH AT+CSCB Check Message Service support Set Text Mode Parameters Show Text Mode Parameters Select Cell Broadcast Message Types Save Settings AT+CSAS AT+CRES AT+CMGL AT+CNMA AT+CMGC AT+CMMS AT+ATV AT+ATX AT+CNMI AT+CPMS AT+CMGW AT+CMSS AT+CMGD AT+CNUM AT+CPBS AT+CPBR AT+CPBW Comment Restore Settings Only one Parameter is supported by the device. Only one Parameter is supported by the device. List messages New message acknowledgement Send Command More Messages to Send DCE response format Result code selection and call progress monitoring control New Message Indications to TE Preferred Message Storage Write Message to Memory Send Message from Storage Delete Messages Get MSISDN Select phonebook memory storage Read phonebook entries Writephonebook entry Safety Recommendations Tbd. _______________________________________________________________________________________________________________ Seite 19 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 7 List of Acronyms 3GPP ADC ADN A-GPS 3 rd Generation Partnership Project Analog Digital Converter Abbrieviated Dialing Number Assisted GPS AMR Adaptive Multi Rate AT AWS BER CLIP CLIR CSD DARP DTMF FDN FTP GSM GPIO GPRS GPS HSPA HW LED MO MT OEM PCB PCM PDU PIN RF RoHs UART USB USIM UMTS WCDMA Attention Command Advanced Wireless Services Bit Error Rate Calling Line Identification Presentation Calling Line Identification Restriction Circuit Switch Data Downlink Advanced Receiver Performance Dual Tone Multi Frequency Fixed Dialing Number File Transfer Protocol Global System for Mobile communication General Purpose Input Output General Packet Radio Service Global Positioning Systen High Speed Uplink Pachet Access Hardware Led Emitting Diode Mobile Originated Mobile Terminated Original Equipment Manufacturer Printed Circuit Board Pulse Code Modulation Protocol Data Unit Personal Identification Number Radio Frequency Restriction of Hazardous Substances Universal Asynchronous Receiver and Transmitter Universal Serial Bus Universal Subscriber Identity Module Universal Mobile Telecommunications System Wideband Code Division Multiple Access _______________________________________________________________________________________________________________ Seite 20 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 8 Warning Statements FCC NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. (c) The provisions of paragraphs (a) and (b) of this section do not apply to digital devices exempted from the technical standards under the provisions of § 15.103. (d) For systems incorporating several digital devices, the statement shown in paragraph (a) or (b) of this section needs to be contained only in the instruction manual for the main control unit. (e) In cases where the manual is provided only in a form other than paper, such as on a computer disk or over the Internet, the information required by this section may be included in the manual in that alternative form, provided the user can reasonably be expected to have the capability to access information in that form. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IC Canada This Class b digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe b est conforme à la norme NMB-003 du Canada. _______________________________________________________________________________________________________________ Seite 21 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Modifications The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by peiker acustic GmbH & Co. KG could void the user's authority to operate the equipment. _______________________________________________________________________________________________________________ Seite 22 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : No Page Count : 22 Producer : AFPL Ghostscript 8.53 Create Date : 2011:10:06 17:23:39 Modify Date : 2011:10:06 17:23:39 Title : V1082-x13_UserManual_Rev4 Creator : FreePDF XP 3.26 - http://shbox.de Author : HEROLDEXIF Metadata provided by EXIF.tools