VTech Telecommunications 80-6684-00 1.9GHz Cordless Phone (Base with Bluetooth) User Manual 3

VTech Telecommunications Ltd 1.9GHz Cordless Phone (Base with Bluetooth) 3

User Manual 3

Telephone operation34Options while on callsHoldYou can place a HOME or CELLULAR call on hold. You will hear an alert tone if you have not taken the call off of hold after 14 minutes. You will hear another alert tone 30 seconds later. After 15 minutes on hold, the call automatically disconnects. To place a HOME call on hold:• Press the HOLD key on the handset. HOME LINE HELD appears on the display and HOME/FLASH will flash. To resume a HOME call that is on hold:• Press HOME/FLASH again. To place a CELLULAR call on hold:• Press the HOLD key on the handset. CELL LINE HELD appears on the display and CELLULAR will flash. To resume a CELLULAR call that is on hold:• Press the CELLULAR key again. HOME LINE HELDCELL LINE HELD
Telephone operation35�hain dialingUse this feature to initiate a dialing sequence from numbers stored in the directory, caller ID history or redial list while you are on a call. This feature is available only when you are making a HOME call. Chain dialing can be useful if you wish to access numbers other than phone numbers (such as bank account information or access codes) from the directory, caller ID history or redial list. Directory access while on a call1. Press MENU/SELECT twice.2. Press DIR / CID to scroll to the desired number. 3. Press MENU/SELECT to dial the number shown. Caller ID history (call log) access while on a call1. Press MENU/SELECT. 2. Press DIR / CID to scroll to >CALL LOG.3. Press MENU/SELECT.4. Press DIR / CID to scroll to the desired number. 5. Press MENU/SELECT to dial the number shown. Last number redial while on a callPress REDIAL/PAUSE to show and dial the most recently dialed number. If you press REDIAL/PAUSE again within two seconds, the number is not dialed.NOTES: 1. You cannot edit a directory entry while you are on a call. For more details about the directory, see page 40.2. You cannot copy a caller ID entry into the directory while you are on a call. For more details about the caller ID history, see page 47.3. If you press REDIAL/PAUSE while on a call, you can only view the most recent call, and you cannot erase the entry. For more details about the redial memory, see page 30.4. Press and hold OFF/CLEAR to exit redial, directory or caller ID history when you are on a call.
Telephone operation36IntercomUse the intercom feature for conversations between handsets. This feature is not available on model TL91178.You can buy additional expansion handsets (model AT&T TL90078) for this telephone base. Up to 12 handsets can be registered to the telephone base. The first nine handsets that you register will be named Handsets 1-9. Use the handset number to intercom and transfer calls.Although the names for handsets 10-12 appears in their displays as 10-12, when you intercom or transfer to one of them, you must use *0 for Handset 10, *1 for handset 11, and *2 for Handset 12.Model TL91278 (two-handset system)1. Press MENU/SELECT when in idle mode to enter the feature menu.2. Use DIR / CID to scroll to >INTERCOM, then press MENU/SELECT.3. The screen shows CALLING OTHER HANDSET. The called handset rings, and its screen shows OTHER HANDSET IS CALLING.4. On the ringing handset, press HOME/FLASH or SPEAKER to answer the intercom call.To end the intercom call:• Press OFF/CLEAR on either handset. -OR-• Place either handset in the charger or telephone base.NOTES:1. Before anyone answers the intercom call, you can cancel the intercom call by pressing OFF/CLEAR on the calling handset.2. If no one answers the called handset within 100 seconds, or if the called handset is in the directory or caller ID history mode, or on a call, or out of range, the calling handset shows UNABLE TO CALL TRY AGAIN. 3. Press OFF/CLEAR or DELETE/MUTE to temporarily silence the intercom ringer.
Telephone operation37IntercomModels TL91378 (three-handset system)1. Press MENU/SELECT when in idle mode to enter the feature menu.2. Use DIR / CID to scroll to >INTERCOM, then press MENU/SELECT. The screen shows INTERCOM TO:3. Enter the handset number 1-9 or, for handsets 10, 11 and 12, enter *0, *1 or *2, respectively. The display shows CALLING HANDSET X, with X being the handset number. The called handset rings, and its screen shows HANDSET X IS CALLING.4. On the ringing handset, press HOME/FLASH or SPEAKER to answer the intercom call.To end the intercom call:• Press OFF/CLEAR on either handset. -OR-• Place either handset in the charger or telephone base.NOTES:1. Before anyone answers the intercom call, you can cancel the intercom call by pressing OFF/CLEAR on the calling handset.2. If no one answers the called handset within 100 seconds, or if it is in the directory or caller ID history mode, or on a call, or out of range, the calling handset shows UNABLE TO CALL TRY AGAIN. 3. Press OFF/CLEAR or DELETE/MUTE to temporarily silence the intercom ringer.4. You can use a maximum of four handsets at a time. When two handsets are used on an intercom call, the other two system handsets can be used for a call on either the HOME or CELLULAR line.
Telephone operation38�all transfer using intercom Use the intercom feature to transfer an outside call to another system handset. This feature is notThis feature is not available on model TL91178.Model TL91278 (two-handset system)1. When on an outside call, press MENU/SELECT to enter the feature menu.2. Use DIR / CID to scroll to >TRANSFER, then press MENU/SELECT. The outside call is automatically placed on hold. The transferring handset’s screen shows CALLING OTHER HANDSET. The called handset rings, and its screen shows OTHER HANDSET IS CALLING.3. On the ringing handset, press HOME/FLASH or SPEAKER to answer the intercom call. You can now talk without the outside caller hearing the conversation.4. Press OFF/CLEAR on the transferring handset or place it in the telephone base or handset charger to complete the transfer. The transferring handset’s screen shows CALL TRANSFERED and the other handset is automatically connected to the outside call. -OR- Press HOME/FLASH or CELLULAR (depending on which call is being transferred) on the called handset to let both parties conference with the external line. NOTES:1. Before anyone answers the intercom call, you can cancel the transfer and return to the outside call by pressing and holding OFF/CLEAR.2. If the called handset does not answer the intercom call within 100 seconds, is in directory or caller ID history mode, or is out of range, the transferring handset shows UNABLE TO CALL TRY AGAIN on its screen and automatically returns to the outside call.3. You can end the intercom call and return to the outside call by pressing HOME/FLASH or CELLULAR (depending on which call is being transferred) on the transferring handset, or pressing OFF/CLEAR on the called handset.
Telephone operation39�all transfer using intercom Models TL91378 (three or more handsets)1. When on an outside call, press MENU/SELECT to enter the feature menu.2. Use DIR / CID to scroll to >TRANSFER, then press MENU/SELECT. The screen shows INTERCOM TO:3. Enter the handset number 1-9 or, for handsets 10, 11 and 12, enter *0, *1 or *2, respectively. The display shows CALLING HANDSET X, with X being the handset number. The called handset rings, and its screen shows HANDSET X IS CALLING.4. On the ringing handset, press HOME/FLASH or SPEAKER to answer the intercom call. You can now talk without the outside caller hearing the conversation.5. Press OFF/CLEAR on the transferring handset or place it in the telephone base or handset charger to complete the transfer. The transferring handset’s screen shows CALL TRANSFERED and the other handset is automatically connected to the outside call. -OR- Press HOME/FLASH or CELLULAR (depending on which call is being transferred) on the destination handset to let both parties conference with the external line. NOTES:1. Before anyone answers the intercom call, you can cancel the transfer and return to the outside call by pressing and holding OFF/CLEAR.2. If the called handset does not answer the intercom call within 100 seconds, is in directory or caller ID history mode, or is out of range, the transferring handset shows UNABLE TO CALL TRY AGAIN on its screen and automatically returns to the outside call.3. You can end the intercom call and return to the outside call by pressing the HOME/FLASH or CELLULAR (depending on which call is being transferred) on the transferring handset, or pressing OFF/CLEAR on the called handset.
Directory40Robert Brown888-883-2445About the directoryShared directoryThe directory is stored in the telephone base, and is shared by all handsets. Changes made to the directory on any one handset applies to all.NOTE: Only one handset can review the directory at a time. If another handset attempts to enter the directory, the screen shows NOT AVAILABLE AT THIS TIME.CapacityThe directory can store up to 50 entries, with a maximum of 15 alphanumeric characters (including spaces) for the names and 30 digits for the telephone numbers. A convenient search feature can help you find and dial numbers quickly (page 44).If there are already 50 entries, the screen shows LIST FULL. You can not store a new number until you delete one.Exiting the directoryPress OFF/CLEAR to cancel an operation, back up to the previous menu, or exit the menu display. Press and hold OFF/CLEAR to return to the idle mode.If you pause for too long while creating or reviewing an entry, the procedure times out and you will have to begin again.
Directory 41�reating directory entriesTo create a new directory entry1. Press MENU/SELECT when in idle mode to enter the feature menu.2. Press MENU/SELECT again to enter >DIRECTORY menu.3. Press DIR or CID to highlight STORE.4. Press MENU/SELECT.5. Enter the telephone number when prompted. • Use the dial pad to enter up to 30 digits. – Press DIR / CID to move the cursor to the right or left. – Press DELETE/MUTE to erase digits. – Press and hold DELETE/MUTE to erase all digits. – Press and hold REDIAL/PAUSE to enter a three-second dialing pause. -OR- • Copy a number from redial by pressing REDIAL/PAUSE then press DIR or CID, or pressing REDIAL/PAUSE repeatedly to locate the number to copy. Press MENU/ SELECT to copy the number.6. Press MENU/SELECT to save the number in the display. The display shows ALREADY SAVED if the number is already in the directory. You cannot save the same number twice.>DIRECTORYCALL LOG>STOREREVIEW>REVIEWSTOREENTER NUMBER888-883-2445_
Directory42�reating directory entries7. Enter the name when prompted. • Use the dial pad to enter a name (up to 15 characters). Each time you press a key, the character on that key appears. Additional key presses produce other characters on that key. See the chart below. – Press– PressPress DIR or CID to move the cursor to the right or left. – Press DELETE/MUTE to erase letters. – Press and hold DELETE/MUTE to erase all letters.DialKey11 2 3 4 5 6 7 8 91 # ‘ , - . &A B C 2 a b cD E F 3 d e fG H I 4 g h iJ K L 5 j k lM N O 6 m n oP Q R S 7 p q r sT U V 8 t u vW X Y Z 9 w x y z0* ? ! / ( ) @spaceCharacters by number of key presses234567890*#8. Press MENU/SELECT to store your new directory entry. The name and the telephone number will then be shown on the screen. To change them later, see pages 45-46.ENTER NAMERobert Brown_Robert Brown888-883-2445NOTE: The first letter of every word is capitalized. The remaining letters in a word begin with lower case letters shown in the chart to the right.
Directory 43Directory reviewTo review directory entries1. Press DIR when in idle mode to show the first entry in the directory. DIRECTORY EMPTY appears if there are no directory entries. -OR- You can also show the first entry in the directory by pressing MENU/SELECT twice, then pressing MENU/SELECT again to choose >REVIEW.2. Press DIR or CID to browse through the directory. Entries appear alphabetically by the first letter in the name. DIR
Directory44Directory searchTo search by name1. Press DIR when in idle mode to show the first listing in the directory. DIRECTORY EMPTY appears if there are no directory entries. 2. When a name entry appears, press the dial pad keys (2-9) to start a name search. The directory shows the first name beginning with the first letter associated with the dial pad key if there is an entry in the directory that begins with that letter.3. To see other names that start with the letters on the same dial pad key, keep pressing the key. The names appear in alphabetical order.For example, if you have the names Jennifer, Jessie, Kevin and Linda in your directory:• If you press 5 (JKL) once, you will see Jennifer.• If you press 5 (JKL) twice, you will see Jessie. • If you press 5 (JKL) three times, you will see Kevin. • If you press 5 (JKL) four times, you will see Linda. • If you press 5 (JKL) five times, you will see Jennifer again. NOTES: 1. If there is no name matching the first letter of the key you press, the directory shows a name that matches the following letters of the key.2. If you press a key (2-9) and no name starts with the letters on that key, the directory shows the entry that matches the next letter in the directory. DIR
Directory 45To dial, delete or edit entriesTo dial, delete or edit a directory entry (name and number), the entry must show on the handset. Use the directory review or search (pages 43-44) to show an entry. Display dialTo dial a displayed number from the directory, press HOME/FLASH or SPEAKER to dial from the HOME line; or press CELLULAR to dial from the CELLULAR line. To delete an entryWhen a directory entry displays, press DELETE/MUTE to delete the displayed entry from the directory. Once deleted, you cannot retrieve an entry. To edit an entryWhen a directory entry displays: 1. Press MENU/SELECT to modify the entry. You are prompted to EDIT NUMBER. Press the dial pad keys to add digits. • Press DELETE/MUTE to erase digits. • Press DIR or CID to move the cursor to the right or left. Press and hold REDIAL/PAUSE to add a three-second pause, if desired. • Copy a number from redial by pressing REDIAL/PAUSE. Then press DIR or CID, or press REDIAL/PAUSE repeatedly to locate the number to copy. Press MENU/ SELECT to copy the number. ••Andrew888-490-2005EDIT NUMBER888-883-2445
Directory462. Press MENU/SELECT. You will be prompted toYou will be prompted to EDIT NAME.Press the dial pad keys to add characters (page 42).Press DELETE/MUTE to erase characters.Press DIR or CID to move the cursor to the right or left.3. Press MENU/SELECT to confirm.•••EDIT NAMEAndyAndy888-883-2445
Caller ID47�aller ID operationThis product supports caller ID services provided by most local telephone service companies. Depending on your service subscription, you may see the caller’s number, or the caller’s name and number that are sent by the telephone company after the first or second ring. If you also have call waiting service, this caller ID information shows when you receive a call while you are on another call. Caller ID from the HOME line allows you to see the name, number, date and time of the incoming call. However, caller ID from the CELLULAR line only shows the number of the incoming call and the Bluetooth name of the paired device; date and time of the call are not shown. These services are available only if both you and the caller are in areas offering caller ID service, and if both telephone companies use compatible equipment.Contact your local telephone company and cellular service provider if:• You have both caller ID and call waiting, but as separate services (you may need to combine these services).• You have only caller ID service, or only call waiting service.• You don’t subscribe to any caller ID or call waiting services. You can use this product with regular caller ID service, or without subscribing to either caller ID or combined caller ID with call waiting service.CHRISTINE SMITH888-722-7702NEW10:01 11/23 AM
Caller ID48�aller ID operationCaller ID history informationIf you subscribe to caller ID services, provided by your local telephone company and�or cellular service provider, the caller ID history storesthe caller ID history stores information for about the last 50 incoming calls for both the HOME and CELLULAR lines.Although the caller ID history records the caller ID information of both lines, caller ID entries from the CELLULAR line only provide the incoming telephone number and the Bluetooth name of the cellular phone. If the number on the incoming CELLULAR call matches a number in the directory, the name is retrieved from the matched directory entry. However, if the caller's number is not provided from the CELLULAR line, the screen only shows INCOMING CALL without showing the Bluetooth name of the device. Review the caller ID history to find out who called, to easily return the call, or to copy the caller’s name and number into your directory.The phone deletes the oldest entry when the log is full to make room for new calls.If you answer a call before the information appears on the screen, it is not saved in the caller ID history.The caller ID history is stored in the telephone base, and is shared by all handsets. Changes made on any one handset is reflected in all.NOTE: Only one handset can review the caller ID history at a time. If another handset attempts to enter the directory or caller ID history, it shows NOT AVAILABLE AT THIS TIME.CHRISTINE SMITH888-722-7702NEW10:01 11/23 AM
Caller ID49Caller’s name Caller’s numberAppears when the call is missed and un-reviewedTime of call Date of callCHRISTINE SMITH888-722-7702NEW10:01AM 11/23 Incoming HOME callIncoming CELLULAR call�aller ID operationMemory matchIf the incoming telephone number exactly matches a telephone number in your directory, the name that appears on the screen matches the corresponding name in your directory. For example, if Christine Smith calls, her name appears as Chris if this is how you entered it into your directory.NOTE: The number shown by your caller ID is in the format sent by the phone company. The phone company usually delivers ten-digit phone numbers (area code plus phone number). If the telephone number of the caller does not exactly match a number in your directory, the name appears as it is delivered by the phone company. For example, if the phone company includes the area code and the directory number does not, the name appears as delivered by the phone company.Chris888-722-7702 NEW10:01AM 11/23
Caller ID50�aller ID operationThere are also occasions when other information or no information shows for various reasons:On-screen messageReasonPRIVATE NUMBERThe caller's number has been set as private.PRIVATE NAMEThe caller's name has been set as private.PRIVATE CALLERCaller's name and telephone number are not revealed at caller's request. UNKNOWN NUMBERYour local telephone company is unable to determine the caller's number. UNKNOWN NAMEYour local telephone company is unable to determine the caller's name. UNKNOWN CALLERYour local telephone company is unable to determine the caller's name and telephone number. Calls from other countries may also generate this message.
Caller ID51HANDSET 16 MISSED CALLS �aller ID operationMissed (new) calls indicatorWhen a handset is in idle mode and has calls that have not been reviewed, its screen will show XX MISSED CALLS. All entries that have not been reviewed are counted as missed calls when the phone is idle. Each time an entry in the caller ID history marked NEW is reviewed, the number of missed calls decreases by one. If you have too many missed calls and you do not want to review them one by one, but you still want to keep them in the caller ID history, you can press and hold OFF/CLEAR for four seconds when the handset is idle. All the entries in the caller ID history will be considered old (have been reviewed), and the missed calls counter is reset to 0.Robert Brown888-883-2445NEW10:31AM11/23
Caller ID52HANDSET 16 MISSED CALLSRobert Brown888-883-2445NEW10:31AM11/23 883-24451-883-2445888-883-24451-888-883-2445 The various dialing options are:To review the caller ID historyTo review the caller ID history1. Press CID to review the caller ID history in reverse chronological order starting with the most recent call. -OR- You can also review the caller ID history by pressing MENU/SELECT, and using DIR or CID to scroll to >CALL LOG, then press MENU/SELECT.2. Press DIR or CID to scroll through the list as shown on the left.To dial from the caller ID historyTo dial a displayed number from the caller ID history:• Press HOME/FLASH or SPEAKER to dial from the HOME line, or press CELLULAR to dial from the CELLULAR line. -OR-• Press # repeatedly to show different dialing options for local and long distance numbers before dialing or saving the telephone number in the directory. See the example on the left. You may also press 1 repeatedly to add or remove a 1 in front of the telephone number before dialing or saving the telephone number in the directory. See the examples on the left. When the number shown is in the correct format for dialing, following the above step to dial the number.CID 883-24451-883-2445 888-883-24451-888-883-2445Press #Press 1Charlie Johnson800-222-3111NEW10:21AM11/23
Caller ID53To review the caller ID historyOther options• Press DELETE/MUTE to delete the shown entry from the caller ID history.• When an entry from the caller ID history is shown, press and hold DELETE/MUTE to delete all entries from the caller ID history. When the screen shows DELETE ALL CALLS? press MENU/SELECT to clear the caller ID history of all entries, or press OFF/CLEAR to exit and leave all entries in the caller ID history intact.• Press MENU/SELECT to copy the entry into your directory. You can edit the name and the number (see pages 45-46).• Press OFF/CLEAR to exit the caller ID history.NOTES: 1. You may need to change how a caller ID number is dialed if the entry does not appear in the correct format. Caller ID numbers may appear with an area code that may not be required for local calls, or without a 1 that may be needed for long distance calls (see page 52).2. If neither the name nor number is provided, UNABLE TO SAVE appears.
54VOICEMAILFlashes when you have new voicemail on your HOME phone line (offered by your telephone service provider). The indicator does not support voicemail on your CELLULAR line.Alert tones and lightsAlert tonesTwo short beeps VOLUME keys are pressed when the volume is already at its highest or lowest setting.Handset tonesFour short beeps Low battery warning.Two beeps Out of range while the handset is on a call.Three rising tones Command completed successfully.LightsIN USEOn when the handset is in use, or when you are registering a handset.Flashes when another telephone is in use on the same line, or when you are de-registering handsets from the telephone base.Flashes quickly when there is an incoming call. •••SPEAKEROn when the speakerphone is on.CHARGEOn when the handset is charging in the telephone base or charger.Blue backlit dial padBlue backlit displayAppendix A BluetoothOn when the telephone base is paired and connected with a cellular phone. Flashes when the Bluetooth feature is activated and waiting for pairing and connection. ••HOME/FLASHFlashes rapidly when there is an incoming HOME call. Flashes slowly when a HOME call is on hold. CELLULARFlashes rapidly when there is an incoming CELLULAR call.Flashes slowly when a CELLULAR call is on hold.
55DIRECTORY EMPTY There are no directory entries.Handset display screen messagesENDED You have just ended a call.CALL LOG EMPTY You are accessing an empty caller ID history.Screen display messagesCELL The CELLULAR line is in use.Another system handset is calling. HANDSET X IS CALLING (For systems with three or more handsets)Appendix BThe handset is calling the other handset (for intercom calls). The handset is going to transfer an outside call to another handset.CALLING OTHER HANDSET(For systems with two handsets)The handset is calling another system handset (for intercom calls). CALLING HANDSET X(For systems with three or more handsets)BLUETOOTH SYSTEMBUSYYou are trying to use a handset to make a CELLULAR call when another handset is already in CELLULAR call predial mode. BOTH LINES HELD Calls on the HOME and CELLULAR lines have been put on hold.CALL TRANSFERED An outside call from one handset is transferred to another handset.ALREADY SAVED The telephone number you have entered is already stored in the directory.CHARGING A handset with a low battery has been placed in the telephone base or charger.CELL LINE HELD A call on the CELLULAR line has been put on hold.
56Handset display screen messagesScreen display messagesMute has just been turned off so your voice will be heard by the other party.MICROPHONE ONYou have started the intercom process, and need to enter the number of the handset you wish to call.INTERCOM TO:(For systems with three or more handsets)The intercom call has just ended.INTERCOM ENDEDThe handset is on an intercom call.INTERCOMAppendix BThere is no cellular phone connected when you are trying to call from the cellular line. NO CONNECTED CELLULAR PHONESHOME The HOME line is in use.MUTED The microphone is muted.LOW BATTERY The battery needs to be charged.INCOMING CALL There is a call coming in.NEW VOICEMAIL There are new voicemail messages on the HOME phone line.XX MISSED CALLS There are new calls in the caller ID history.LINE IN USE An extension phone or one of the handsets is in use.LIST FULL The directory is full. No new entries can be saved unless some current entries are deleted.HOME LINE HELD A call on the HOME line has been put on hold.HANDSET X REGISTEREDThe handset registration is successful, with X being the handset number.
57Failed intercom or conference call (there are already two handsets being used).UNABLE TO CALL TRY AGAINSomeone else is already using the directory or caller ID history. NOT AVAILABLEAT THIS TIMEOUTSIDE CALL You are connected to the external call during call transfer. UNABLE TO SAVE You are trying to save an entry with no name or number from the caller ID history.The battery is very low. The handset should be placed in the telephone base or charger.PLACE IN CHARGERRINGER MUTE The ringer is muted temporarily during an incoming call. NO LINE There is no telephone line connected.SAVED The entry in caller ID history is saved to the directory successfully.The handset is out of range while on a call.NO SIGNAL, CALL ENDEDYou have started transferring a call, and need to enter the desired handset number.TRANSFER TO: (For systems with three or more handsets)Handset display screen messagesScreen display messagesAppendix BSEARCHINGFOR BASEThe handset has lost communication with the telephone base.** PAGING ** The telephone base is paging handsets.OTHER HANDSET IS CALLINGThe other handset is calling. (For system with two handsets)
58Expansion handsetYour new AT&T TL91178�TL91278�TL91378 telephone system canTL91178�TL91278�TL91378 telephone system cantelephone system can accommodate up to 12 handsets. You can add new handsets (AT&T TL90078, purchased separately) to your telephone system, but you must register each device with the telephone base before use. To register a new handset, see page 59. TL91178The handsets provided with the TL91178 come pre-registered as HANDSET 1. You can register up to 11 additional handsets to the telephone base, and they will be assigned numbers in the order they are registered (HANDSET 2, HANDSET 3, HANDSET 4 and so on).TL91278The handsets provided with the TL91278 come pre-registered as HANDSET 1 and HANDSET 2. You can register up to 10 additional handsets to the telephone base, and they will be assigned numbers in the order they are registered (HANDSET 3, HANDSET 4, HANDSET 5 and so on).TL91378The handsets provided with the TL91378 come pre-registered as HANDSET 1, HANDSET 2 and HANDSET 3. You can register up to nine additional handsets to the telephone base, and they will be assigned numbers in the order they are registered (HANDSET 4, HANDSET 5, HANDSET 6 and so on).Appendix C
59HANDSET X REGISTEREDExpansion handset Adding and registering handsets (optional)Handsets purchased separately (AT&T TL90078) need to be registered to the telephone base before use. When first purchased, all expansion handsets show NOT REGISTERED on the screen. You may need to charge the new handsets for five minutes before registering to the telephone base.To register a handset to your telephone base1. Place the unregistered handset into the telephone base. If PRESS HNDST LOC 4 SEC ON BASE does not appear on the handset screen after a few seconds, remove the handset and place it in the telephone base again.2. On the telephone base, press and hold HANDSET LOCATOR for about four seconds (until the red IN USE light on the telephone base turns on) and then release the button. The handset shows PLEASE WAIT... and it will take about 10 seconds to complete the registration. The handset shows HANDSET X REGISTERED, with X being the handset number (1-12). You will hear three rising beeps when the registration is successful. NOTES: 1. If the registration is not successful, the display shows NOT REGISTERED. To reset the handset, remove the handset from the telephone base and place it back in. Try the registration process again.2. You cannot register a handset if any other system handset is in use.PRESS HNDST LOC4 SEC ON BASEPLEASE WAIT...NOT REGISTEREDAppendix C
60Expansion handset Replacing a handsetYou can de-register handsets. You may need to de-register your handsets if:You have twelve registered handsets and need to replace a handset. -OR-You wish to change the designated handset number of your registered handsets.You must first de-register ALL the handsets, and then re-register each handset you wish to use.Please read carefully through all the instructions on this page before beginning the de-registration process.To de-register all handsets1. Press and hold HANDSET LOCATOR on the telephone base for about 10 seconds (until the IN USE light turns on and starts to flash), then release the HANDSET LOCATOR button.2. Immediately press and release HANDSET LOCATOR again. You must press HANDSET LOCATOR while the IN USE light is still flashing. (The light flashes for about seven seconds. If the light stops flashing, pick up the handset and place it back into the telephone base, then start again with step one above.)3. The handsets will show SEARCHING FOR BASE and it will take about 10 seconds to complete the de-registration process. ALL handsets will show NOT REGISTERED when de-registration is successful.4. To re-register the handsets to the telephone base, follow the registration instructions on page 59.NOTES:1. If the de-registration process was not successful, you may need to reset the system and try again. To reset: pick up the handset and press the HOME/FLASH button, then press the OFF/CLEAR button and place the handset back into the telephone base. You may also reset by unplugging the power from the telephone base and plugging it back in.2. You cannot de-register the handsets if any other system handset is in use. Appendix C
61TroubleshootingIf you have difficulty with your phone, please try the suggestions below. For Customer Service, visit our website at www.telephones.att.com or call 1 (800) 222-3111. In Canada, dial 1 (866) 288-4268. I cannot pair my cell phone to the telephone base.• Make sure the Bluetooth function of your cellular phone is turned on. See your cell phone user's manual for more information.• Remove the AT&T DECT 6.0 from your cell phone's handsfree device history list (see you cell phone user's manual for more information).• Carefully follow the pairing instructions on page 17, making sure that your cell phone is not connected to any other Bluetooth device.• Turn off your cell phone, then turn it on again.• Reset the telephone base. Unplug the electrical power. Wait for approximately 15 seconds, then plug it back in. Repeat the above suggestions.I cannot connect my cell phone with the telephone base.• Make sure that the Bluetooth function of your cell phone is turned on. See your cell phone user's manual for more information.• Make sure that your Bluetooth cell phone is not connected to any other Bluetooth device.• Turn off your cell phone, then turn it on again.• For some cell phones, you must authorize the AT&T DECT 6.0 device in your cell phone's Bluetooth feature. See your cell phone user's manual for more information.• If the telephone base does not connect to your paired cellular phone automatically, you may need to connect to that device manually, refer to page 18 for details. • If the cellular phone does not connect to the telephone base after trying manual connection, delete AT&T DECT 6.0 from the paired device list in your cellular phone, then start again with the pairing procedures (page 17). Appendix D
62My cell phone disconnects from the telephone base.• Turn off your cell phone, then turn it on again.• Make sure that you are not using your cell phone when on a CELLULAR call.• When you are on a CELLULAR call using the handset, your cell phone is in use. Attempting to use the cell phone for any other purpose may disconnect your call.You may need to connect the cellular phone to the telephone base manually to resume the connection, refer to page 18 for details.I don't know how to search for or add new devices on my cell phone.• Most cell phones have the Bluetooth feature in the connection or setup menus. Please refer to your cell phone user's manual. • In general, press the menu key on your cell phone, then look for the Bluetooth menu in the settings or connection menu. In the Bluetooth menu, select the option to search for or add new devices. Troubleshooting• Make sure that the Bluetooth feature is turned on in the telephone base. Carefully follow the setup instructions on page 17.• Make sure that you manually set your cell phone to find or search for devices.• Turn off your cell phone, then turn it on again.• Reset the telephone base. Unplug the electrical power. Wait for approximately 15 seconds, then plug it back in. Repeat the above suggestions.I cannot find the AT&T DECT 6.0 on my cell phone. Appendix D• When you are on a CELLULAR call using the handset, your cell phone is in use. Attempting to use the cell phone for any other purpose may disconnect your call.You may need to connect the cellular phone to the telephone base manually to resume the connection, refer to page 18 for details.
63I cannot hear any sound on my telephone system when on a CELLULAR call.• Reset the telephone base. Unplug the electrical power. Wait for approximately 15 seconds, then plug it back in.• Turn off your cell phone, then turn it on again.TroubleshootingMy phone doesn’t work at all.• Make sure the power cord is securely plugged in.• Make sure that the battery connector is securely plugged into the cordless handset.• Make sure the telephone line cord is securely and firmly plugged into the telephone base and the telephone wall jack.• Charge the battery in the cordless handset for at least 16 hours. For optimum daily performance, return the cordless handset to the telephone base or charger when not in use.The PIN on the telephone base does not work.• The default PIN is 0000.Bluetooth System Busy appears on the display.• Make sure that your cellular phone is not in use when connected to the telephone base. • Make sure that your cellular phone is not connected to any other Bluetooth device.• The AT&T DECT 6.0 can only use one Bluetooth device at a time.Appendix D• Make sure that your cell phone is not in use when you are trying to make a CELLULAR call. • Make sure that your cell phone is compatible. For a list of compatible devices, visit www.telephones.att.com/bluetooth.• For some smartphones, make sure that the cellular function is turned on.My cell phone is connected to the telephone base, but I cannot make a CELLULAR call.
64I cannot get a dial tone.• First try all the suggestions above.• Move the cordless handset closer to the telephone base. You might have moved out of range.• If the previous suggestions don’t work, disconnect the telephone base from the telephone jack and connect to a different phone. If there is no dial tone on that phone either, the problem is in your wiring or local service. Contact your local telephone company.• Your line cord might be malfunctioning. Try installing a new line cord.Troubleshooting• First try all the suggestions above.• Make sure you have a dial tone before dialing. The cordless handset may take a second or two to find the telephone base and produce a dial tone. This is normal. Wait an extra second before dialing.• Eliminate any background noise. Noise from a television, radio or other appliances may cause the phone to not dial out properly. If you cannot eliminate the background noise, first try muting the cordless handset before dialing, or dialing from another room in your home with less background noise.• If the other phones in your home are having the same problem, the problem is in your wiring or local service. Contact your local telephone company (charges may apply).I cannot dial out.Appendix D• Reset the telephone base. Unplug the electrical power. Wait for approximately 15 seconds, then plug it back in. Allow up to one minute for the cordless handset and tel-ephone base to reset.• You may need to purchase a new battery. Please refer to Battery installation & charging, page 9, in this user’s manual.
65TroubleshootingSEARCHING FOR BASEappears on my cordless handset.• Ensure that the telephone base is powered up.• Place the cordless handset in the telephone base for one minute to allow the cordless handset and base to resynchronize.• Move the cordless handset closer to the telephone base. You might have moved out of range.• Reset the telephone base. Unplug the electrical power. Wait for 15 seconds then plug it back in. Allow up to one minute for the cordless handset and telephone base to reset.• Other electronic products can cause interference with your cordless phone. Try installing your phone as far away from these types of electronic devices as possible: television sets, VCRs, or other cordless telephones.Appendix DMy cordless handset isn’t performing normally.• Make sure the power cord is securely plugged into the telephone base. Plug the power adapter into a different, working electrical outlet not controlled by a wall switch.• Move the cordless handset closer to the telephone base. You might have moved out of range.• Reset the telephone base. Unplug the electrical power. Wait for 15 seconds then plug it back in. Allow up to one minute for the cordless handset and telephone base to reset.• Other electronic products can cause interference to your cordless phone. Try installing your phone as far away from these types of electronic devices as possible: television sets, VCRs, or other cordless telephones.
66TroubleshootingThe batteries will not hold a charge.I get noise, static, or weak signals even when I’m near the telephone base.If you subscribe to high-speed Internet service (digital subscriber line - DSL) through your telephone lines, you must install a DSL filter between the telephone base and the telephone wall jack (see page 7). The filter prevents noise and caller ID problems caused by DSL interference. Please contact your DSL service provider for more information about DSL filters.• You may be able to improve the performance of your cordless phone by installing your new telephone base as far as possible from any other existing cordless telephone system that may already be installed.• Other electronic products can cause interference to your cordless phone. Try installing your phone as far away from the following electronic devices as possible: television sets, VCRs, or other cordless telephones.• Do not install this phone near a microwave oven or on the same electrical outlet. You may experience decreased performance while the microwave oven is operating.• If your phone is plugged in with a modem or a surge protector, plug the phone (or modem�surge protector) into a different location. If this doesn't solve the problem, re-locate your phone or modem farther apart from one another, or use a different surge protector.•• If the cordless handset is in the telephone base or charger and the charge light does not come on, refer to The charge light is off in this Troubleshooting guide.• Charge the battery in the cordless handset for at least 16 hours. For optimum daily performance, return the cordless handset to the telephone base or charger when not in use.• You may need to purchase a new battery. Please refer to Battery installation & charging, page 9, in this user’s manual.Appendix D
67Troubleshooting• Relocate your phone to a higher location. The phone will likely have better reception when installed in a high area.• If the other phones in your home are having the same problem, the problem is in your wiring or local service. Contact your local telephone company (charges may apply).• You may hear interference if your cellular phone is too close to the telephone base during a CELLULAR call. Make sure that your Bluetooth enabled cellular phone is between one to 12 feet away from the telephone base in order to maintain a reliable connection between your Bluetooth cell phone, telephone base, and cell tower.I hear other calls while using my phone.• Disconnect the telephone base from the telephone jack, and plug in a different telephone. If you still hear other calls, the problem is probably in your wiring or local service. Call your local telephone company.• Make sure that the ringer is not turned off. Refer to Ringer volume on page 21 in this user’s manual.• Make sure the telephone line cord is plugged securely into the telephone base and the telephone jack. Make sure the power cord is securely plugged in.• The cordless handset may be too far from the telephone base.• Charge the battery in the cordless handset for at least 16 hours. For optimum daily performance, return the cordless handset to the telephone base or charger when not in use.My cordless handset does not ring when I receive a call.I experience poor sound quality when using the speakerphone. • For increased sound quality while using the speakerphone, place the handset on a flat surface with the dial pad facing up. Appendix D
68• You may have too many extension phones on your telephone line to allow all of them to ring simultaneously. Try unplugging some of the other phones.• The layout of your home or office might be limiting the operating range. Try moving the telephone base to another location, preferably on an upper floor.• If the other phones in your home are having the same problem, the problem is in your wiring or local service. Contact your local telephone company (charges may apply).• Test a working phone at the phone jack. If another phone has the same problem, the problem is the phone jack. Contact your local telephone company (charges may apply).• Other electronic products can cause interference with your cordless phone. Try installing your phone as far away as possible from electronic devices such as television sets, VCRs, or other cordless telephones.• Re-install the battery, and place the cordless handset in the telephone base. Wait for the cordless handset to re-establish its connection with the telephone base. Allow up to one minute for this to take place. • Your line cord might be malfunctioning. Try installing a new line cord.Troubleshooting• Other electronic products can cause interference with your cordless phone. Try installing your phone as far away from the following electronic devices as possible: television sets, VCRs, or other cordless telephones.• Do not install this phone near a microwave oven or on the same electrical outlet. You may experience decreased performance while the microwave oven is operating.My calls cut in and out while I’m using my cordless handset.Appendix D
69The charge light is off.• Make sure the power and line cords are plugged in correctly and securely.• Unplug the electrical power. Wait for 15 seconds, then plug it back in. Allow up to one minute for the cordless handset and telephone base to reset.• Clean the cordless handset and telephone base charging contacts each month using a pencil eraser or cloth.My caller ID isn’t working.• Caller ID is a subscription service. You must subscribe to this service from your local telephone company for this feature to work on your phone.• Your caller must be calling from an area that supports caller ID.• Both you and your caller’s telephone companies must use caller ID compatible equipment.If you subscribe to high-speed Internet service (digital subscriber line - DSL) through your telephone lines, you must install a DSL filter between the telephone base and the telephone wall jack (page 7). The filter prevents noise and caller ID problems caused by DSL interference. Please contact your DSL service provider for more information about DSL filters.•Troubleshooting• If your phone is plugged in with a modem or surge pro-tector, plug the phone (or modem�surge protector) into a different location. If this doesn't solve the problem, re-locate your phone or modem farther apart from one another, or use a different surge protector.• Relocate your telephone base to a higher location. The phone will have better reception when installed in a high area.• If the other phones in your home are having the same problem, the problem is in your wiring or local service. Contact your local telephone company (charges may apply).Appendix D
System does not receive caller ID when on a call.• Make sure you subscribe to caller ID with call waiting features provided by your local telephone company. Caller ID features will work only if both you and the caller are in areas offering caller ID service, and if both telephone companies use compatible equipment.TroubleshootingCommon cure for electronic equipment.If the telephone does not seem to be responding normally, try putting the cordless handset in the telephone base or charger. If it does not seem to respond, do the following (in the order listed):• Disconnect the power to the telephone base.• Disconnect the cordless handset battery, and spare battery, if applicable.• Wait a few minutes.• Connect power to the telephone base.• Re-install the battery, and place the cordless handset into the telephone base.• Wait for the cordless handset to re-establish its connection with the telephone base. Allow up to one minute for this to take place.Appendix D70
71Appendix ETaking care of your telephoneYour cordless telephone contains sophisticated electronic parts, so it must be treated with care.Avoid rough treatment. Place the handset down gently. Save the original packing materials to protect your telephone if you ever need to ship it.Avoid waterYour telephone can be damaged if it gets wet. Do not use the handset in the rain, or handle it with wet hands. Do not install the telephone base near a sink, bathtub or shower.Electrical stormsElectrical storms can sometimes cause power surges harmful to electronic equipment. For your own safety, take caution when using electric appliances during storms.Cleaning your telephoneYour telephone has a durable plastic casing that should retain its luster for many years. Clean it only with a soft cloth slightly dampened with water or a mild soap.Do not use excess water or cleaning solvents of any kind.••••••••MaintenanceRemember that electrical appliances can cause serious injury if used when you are wet or stand-ing in water. If the telephone base should fall into water, DO NOT RETRIEVE IT UNTIL YOU UN-PLUG THE POWER CORD AND TELEPHONE LINE CORDS FROM THE WALL. Then pull the telephone out by the unplugged cords.
72Important safety informationThis symbol is to alert you to important operating or servicing instructions that may appear in this user’s manual. Always follow basic safety precautions when using this product to reduce the risk of injury, fire, or electric shock.Safety informationRead and understand all instructions in the user’s manual. Observe all markings on the product.Avoid using a telephone during a thunderstorm. There may be a slight chance of electric shock from lightning.Do not use a telephone in the vicinity of a gas leak. If you suspect a gas leak, report it immediately, but use a telephone away from the area where the gas is leaking. If this product is a cordless model, make sure the telephone base is also away from the area.Do not use this product near water, or when you are wet. For example, do not use it in a wet basement or shower, or next to a swimming pool, bathtub, kitchen sink, or laundry tub. Do not use liquids or aerosol sprays for cleaning. If the product comes in contact with any liquid, unplug any line or power cord immediately. Do not plug the product back in until it has dried thoroughly.Install this product in a protected location where no one can trip over any line or power cords. Protect cords from damage or abrasion.If this product does not operate normally, see the Troubleshooting section on pages 61-70 of this user’s manual. If you cannot solve the problem, or if the product is damaged, refer to the Limited warranty on pages 78-80. Do not open this product except as directed in your user’s manual. Opening the product or reassembling it incorrectly may expose you to hazardous voltages or other risks.Replace batteries only as described in your user’s manual. Do not burn or puncture batteries — they contain caustic chemicals.This power adapter is intended to be correctly oriented in a vertical or floor mount position. The prongs are not designed to hold the plug in place if it is plugged into a ceiling or an under-the-table�cabinet outlet.••••••••Appendix F
73Appendix FImportant safety informationCaution: Use only the power adapter provided with this product. To obtain a replacement, visit our website at www.telephones.att.com or call 1 (800) 222-3111. In Canada, dial 1 (866) 288-4268.Especially about cordless telephones Privacy: The same features that make a cordless telephone convenient create some limitations. Telephone calls are transmitted between the telephone base and the handset by radio waves, so there is a possibility that your cordless telephone conversations could be intercepted by radio receiving equipment within range of the cordless handset. For this reason, you should not think of cordless telephone conversations as being as private as those on corded telephones. Electrical power: The telephone base of this cordless telephone must be connected to a working electrical outlet which is not controlled by a wall switch. Calls cannot be made from the handset if the telephone base is unplugged, switched off or if the electrical power is interrupted. Potential TV interference: Some cordless telephones operate at frequencies that may cause interference to TVs and VCRs. To minimize or prevent such interference, do not place the telephone base of the cordless telephone near or on top of a TV or VCR. If interference is experienced, moving the cordless telephone farther away from the TV or VCR will often reduce or eliminate the interference. Rechargeable batteries: This product contains nickel-metal hydride rechargeable batteries. Exercise care in handling batteries in order not to create a short circuit with conductive material such as rings, bracelets, and keys. The battery or conductor may overheat and cause harm. Observe proper polarity between the battery and the battery charger. Nickel-metal hydride rechargeable batteries: Dispose of these batteries in a safe manner. Do not burn or puncture. Like other batteries of this type, if burned or punctured, they could release caustic material which could cause injury.•••••
74Important safety informationThe RBRC™ Seal means that the manufacturer is voluntarily participating in an industry program to collect and recycle nickel-metal hydride rechargeable batteries when taken out of service within the United States. These batteries may be taken to a participating local retailer of replacement batteries or recycling center. Or you may call 1 (800) 8-BATTERY for locations accepting spent Ni-MH batteries.Precautions for users of implanted cardiac pacemakersCardiac pacemakers (applies only to digital cordless telephones): Wireless Technology Research, LLC (WTR), an independent research entity, led a multidisciplinary evaluation of the interference between portable wireless telephones and implanted cardiac pacemakers. Supported by the U.S. Food and Drug Administration, WTR recommends to physicians that:Pacemaker patientsShould keep wireless telephones at least six inches from the pacemaker.Should NOT place wireless telephones directly over the pacemaker, such as in a breast pocket, when it is turned ON.Should use the wireless telephone at the ear opposite the pacemaker.WTR’s evaluation did not identify any risk to bystanders with pacemakers from other persons using wireless telephones.SAVE THESE INSTRUCTIONS•••Appendix F
75Appendix GF�� part 68 and A�TAThis equipment complies with Part 68 of the FCC rules and with technical requirements adopted by the Administrative Council for Terminal Attachments (ACTA). The label on the back or bottom of this equipment contains, among other things, a product identifier in the format US:AAAEQ##TXXXX. This identifier must be provided to your local telephone company upon request.The plug and jack used to connect this equipment to premises wiring and the telephone network must comply with the applicable Part 68 rules and technical requirements adopted by ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. An RJ11 jack should normally be used for connecting to a single line and an RJ14 jack for two lines. See Installation Instructions in the user’s manual.The Ringer Equivalence Number (REN) is used to determine how many devices you may connect to your telephone line and still have them ring when you are called. The REN for this product is encoded as the 6th and 7th characters following the US: in the product identifier (e.g., if ## is 03, the REN is 0.3). In most, but not all areas, the sum of all RENs should be five (5.0) or less. For more information, please contact your local telephone company.This equipment may not be used with Party Lines. If you have specially wired alarm dialing equipment connected to your telephone line, ensure the connection of this equipment does not disable your alarm equipment. If you have questions about what will disable the alarm equipment, consult your telephone company or a qualified installer.If this equipment is malfunctioning, it must be unplugged from the modular jack until the problem has been corrected. Repairs to this telephone equipment can only be made by the manufacturer or its authorized agents. For repair procedures, follow the instructions outlined under the Limited Warranty.If this equipment is causing harm to the telephone network, the telephone company may temporarily discontinue your telephone service. The telephone company is required to notify you before interrupting service. If advance notice is not practical, you will be notified as soon as possible. You will be given the opportunity to correct the problem and the telephone company is required to inform you of your right to file a complaint with the FCC. Your telephone company may make changes in its facilities, equipment, operation,
76Appendix GF�� part 68 and A�TAor procedures that could affect the proper functioning of this product. The telephone company is required to notify you if such changes are planned.If this product is equipped with a corded or cordless handset, it is hearing aid compatible.If this product has memory dialing locations, you may choose to store emergency telephone numbers (e.g., police, fire, medical) in these locations. If you do store or test emergency numbers, please:Remain on the line and briefly explain the reason for the call before hanging up.Perform such activities in off-peak hours, such as early morning or late evening.Industry CanadaOperation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference, including interference that may cause undesired operation.The term ‘’IC:‘’ before the certification�registration number only signifies that the Industry Canada technical specifications were met.The Ringer Equivalence Number (REN) for this terminal equipment is 0.1. The REN is an indication of the maximum number of devices allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the RENs of all the devices does not exceed five.This product meets the applicable Industry Canada technical specifications.
77F�� part 15This equipment has been tested and found to comply with the requirements for a Class B digital device under Part 15 of the Federal Communications Commission (FCC) rules. These requirements are intended to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio�TV technician for help.Changes or modifications to this equipment not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Privacy of communications may not be ensured when using this telephone.To ensure safety of users, the FCC has established criteria for the amount of radio frequency energy that can be safely absorbed by a user or bystander according to the intended usage of the product. This product has been tested and found to comply with the FCC criteria. The handset may be safely held against the ear of the user. The telephone base shall be installed and used such that parts of the user’s body other than the hands are maintained at a distance of approximately 20 cm (8 inches) or more. This Class B digital apparatus complies with Canadian ICES-003.Appendix H
78Appendix ILimited warrantyThe AT&T brand is used under license - any repair, replacement or warranty service, and all questions about this product should be directed to: In the United States of America, visit www.telephones.att.com or call 1 (800) 222-3111. In Canada, call 1 (866) 288-4268.1. What does this limited warranty cover? The manufacturer of this AT&T-branded product warrants to the holder of a valid proof of purchase (“CONSUMER” or “you”) that the product and all accessories provided in the sales package (“PRODUCT”) are free from defects in(“PRODUCT”) are free from defects inPRODUCT”) are free from defects in material and workmanship, pursuant to the following terms and conditions, when installed and used normally and in accordance with the PRODUCT operating instructions. This limited warranty extends only to the CONSUMER for products purchased and used in the United States of America and Canada.2. What will be done if the PRODUCT is not free from defects in materials and workmanship during the limited warranty period (“materially defective PRODUCT”)? During the limited warranty period, the manufacturer’s authorized service representative will repair or replace at the manufacturer’s option, without charge, a materially defective PRODUCT. If the manufacturer repairs the PRODUCT, they may use new or refurbished replacement parts. If the manufacturer chooses to replace the PRODUCT, they may replace it with a new or refurbished PRODUCT of the same or similar design. The manufacturer will retain defective parts, modules, or equipment. Repair or replacement of the PRODUCT, at the manufacturer’s option, is your exclusive remedy. The manufacturer will return repaired or replacement products to you in working condition. You should expect the repair or replacement to take approximately 30 days.3. How long is the limited warranty period? The limited warranty period for the PRODUCT extends for ONE (1) YEAR from the date of purchase. If the manufacturer repairs or replaces a materially defective PRODUCT under the terms of this limited warranty, this limited warranty also applies to repaired or replacement PRODUCT for a period of either (a) 90 days from the date the repaired or replacement PRODUCT is shipped to you or (b) the time remaining on the original one-year limited warranty; whichever is longer.
79Appendix ILimited warranty4. What is not covered by this limited warranty?This limited warranty does not cover:PRODUCT that has been subjected to misuse, accident, shipping or other physical damage, improper installation, abnormal operation or handling, neglect, inundation, fire, water, or other liquid intrusion; orPRODUCT that has been damaged due to repair, alteration, or modification by anyone other than an authorized service representative of the manufacturer; orPRODUCT to the extent that the problem experienced is caused by signal conditions, network reliability or cable or antenna systems; orPRODUCT to the extent that the problem is caused by use with non-AT&T accessories; orPRODUCT whose warranty�quality stickers, PRODUCT serial number plates or electronic serial numbers have been removed, altered or rendered illegible; orPRODUCT purchased, used, serviced, or shipped for repair from outside the United States of America or Canada, or used for commercial or institutional purposes (including but not limited to products used for rental purposes); orPRODUCT returned without valid proof of purchase (see item 6 below); -or-Charges for installation or setup, adjustment of customer controls, and installation or repair of systems outside the unit.5. How do you get warranty service? To obtain warranty service in the United States of America, visit www.telephones.att.com or call 1 (800) 222-3111. In Canada, call 1 (866) 288-4268. NOTE: Before calling for service, please review the user’s manual; a check of the PRODUCT controls and features may save you a service call. Except as provided by applicable law, you assume the risk of loss or damage during transit and transportation and are responsible for delivery or handling charges incurred in the transport of the PRODUCT(s) to the service location. The manufacturer will return repaired or replaced PRODUCT under this limited warranty to you. Transportation, delivery or handling charges are prepaid. The manufacturer assumes no risk for damage or loss of the PRODUCT in transit. If the PRODUCT failure is not covered by this limited warranty, or proof of purchase does not meet the terms of this limited warranty, the manufacturer will notify you and will request that you authorize the cost of repair prior to any further repair activity. ••••••••
80Limited warrantyYou must pay for the cost of repair and return shipping costs for the repair of products that are not covered by this limited warranty.6. What must you return with the PRODUCT to get warranty service? You must:Return the entire original package and contents including the PRODUCT to the service location along with a description of the malfunction or difficulty; andInclude “valid proof of purchase” (sales receipt) identifying the PRODUCT purchased (PRODUCT model) and the date of purchase or receipt; andProvide your name, complete and correct mailing address, and telephone number.7. Other limitations This warranty is the complete and exclusive agreement between you and the manufacturer of this AT&T branded PRODUCT. It supersedes all other written or oral communications related to this PRODUCT. The manufacturer provides no other warranties for this PRODUCT. The warranty exclusively describes all of the manufacturer’s responsibilities regarding the PRODUCT. There are no other express warranties. No one is authorized to make modifications to this limited warranty and you should not rely on any such modification. State�Provincial Law rights: This warranty gives you specific legal rights, and you may also have other rights which vary from state to state or province to province. Limitations: Implied warranties, including those of fitness for a particular purpose and merchantability (an unwritten warranty that the PRODUCT is fit for ordinary use) are limited to one year from date of purchase. Some states�provinces do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. In no event shall the manufacturer be liable for any indirect, special, incidental, consequential, or similar damages (including, but not limited to lost profits or revenue, inability to use the PRODUCT or other associated equipment, the cost of substitute equipment, and claims by third parties) resulting from the use of this PRODUCT. Some states�provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.Please retain your original sales receipt as proof of purchase.a.b.c.Appendix I
81Appendix JTechnical specificationsRF frequency band 1921.536 MHz — 1928.448 MHzChannels 5Operating temperature 32°F — 122°F0°C — 50°CTelephone base voltage(AC voltage, 60Hz)96 — 129 VrmsTelephone base voltage(AC adapter output)6VDC @400mAHandset voltage 2.4 — 3.2 VDCCharger voltage(AC adapter output)6VAC @300mAReplacement battery 2.4V 750mAHOperation Operating time*Talk time (handset) Up to nine hoursTalk time (speakerphone) Up to two hoursStandby Up to five days* Operating times will vary depending on your actual use and the age of the battery.
82DECT 6.0 digital technologyThe AT&T DECT 6.0 products offer unsurpassed range performance and sound clarity. This is achieved through a unique antenna design and advances in noise-filtering technology. An independent laboratory has confirmed that AT&T DECT 6.0 products perform up to 45% better in range competitions. Now calls can be taken in the basement, backyard and garage with exceptional sound quality. Telephone operating rangeThis cordless telephone operates within the maximum power allowed by the Federal Communications Commission (FCC). Even so, this handset and telephone base can communicate over only a certain distance — which can vary with the locations of the telephone base and handset, the weather, and the construction of your home or office. Extended range and clarityThis telephone base comes with an antenna which gives much better clarity and covers a longer range than before.Technical specificationsAppendix J
AAlert tones, 54Answering calls CELLULAR calls, 28 HOME calls, 26Auto connection, 17BBattery, Charging, 9 Installation, 9Bluetooth Introduction, 15 Pairing, 17 Replace a paired device, 19 Setup, 17Bonding, 16CCall, Transfer, 38-39 Waiting, CELLULAR calls, 29 HOME calls, 26Caller ID (CID), 47 Add entries to phone directory, 53 Delete entries, 53 Dial entries, 52Chain dialing, 35 Clear voicemail indication, 24 Conference, 32DDe-registration, 60Delete entries in the caller ID history, 53Delete redial entries, 31Dialing, From a record in the caller ID history, 52 Directory dialing, 45Directory, 40 Dial number, 45 Edit entries, 45-46 Name search, 44 New entries, 41-42 Display dial, 45DSL, 7EElapsed time, 26, 28Ending calls, 26-29 Expansion handset, 58FFlash (switch hook flash), 26, 29GGlossary of terms (Bluetooth), 16HHandset, De-registration, 60 Expansion, 58 Key tone, 23 Language, 23 Locator, 31 Main menu, 20 Quick reference guide, 1-3 Registration, 59 Ringer tone, 22 Ringer volume, 21 Screen display messages, 55-57 Settings, 21-25 Speakerphone, 30Speakerphone, 30 Index83
Index Status icons, 4 Temporary ringer silencing, 25 Voicemail indicator, 24 Hold, 34 HOME, 1, 16IIntercom, 36-37Incoming caller ID history, 52Incoming calls, answering, 26, 28 Installation, 5-14KKey tone, 23LLanguage, 23Last number redial, 30Lights, 54MMaking calls, CELLULAR calls, 28 HOME calls, 26 Maintenance, 71 Manual connection, 18 Memory match, 49 Missed calls indicator, 51Mute, 33NNames, Enter into directory, 42 Search for, 44PPairing, 17 Paging tone, 31Passkey�Passcode, 16 PIN, 16 Power adapter, 7-8 Predialing, 26, 28QQuick reference guide, 1-3RReceiving calls, 26-29Redial, 30Registration, 59 Resume auto connection, 19 Ring tone options, 22Ringer silencing, 21, 25Ringer volume, 21SSafety information, 72-74 Search by name, 44Speakerphone, 30TTechnical specifications, 81-82 Telephone operating range, 82Temporary ringer silencing, 25Troubleshooting, 61-70 Turn off the auto connection, 18VVoice mail waiting indicator, 24 Voicemail, 3, 24, 54 Volume controls, Handset, 32 Handset ringer, 21 WWall-mount installation, 10-14 Warranty, 78-8084
www.telephones.att.com© 2008 Advanced American Telephones. All rights reserved. AT&T and the AT&T logo are trademarks of AT&T Intellectual Property II, L.P. d/b/a AT&T Intellectual Property licensed to Advanced American Telephones. Printed in �hina. Issue 1 AT&T 10/08.The Bluetooth® word mark and logos are owned by Bluetooth SIG, Inc. and any use of such marks by Advanced American Telephones and its parent, VTech Holdings Limited, is under license. VTech Holdings Limited is a member of Bluetooth SIG, Inc. Other trademarks and trade names are those of their respective owners.

Navigation menu