Venture Global HAXPFAT Multi-Functional Alarm Transmitter User Manual 2

Venture Global Limited Multi-Functional Alarm Transmitter 2

Manual

FCC Statement:This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: Modifications to this product will void the user's authority to operate this equipment.RModeMatPad+3SIIIRModeMatPad+3SIIIRModeMatPad+3SIIIUSER MANUAL HAX-300-500PWRTXSNDLIGHTOnOffOnOffReCodeAOnOffBMode SoundHiLoOffNONC3SParts and Function121011131415161217 1834567891. Batteries compartment2. Battery Door3. Regenerates new code button. 4. Power on/off switch5. Transmitter On/off switch. 6. Alert sound selector.Power+Remove the screw and slide to openthe battery coverFlip to open the cover Insert 3 AAA bateries tothe battery compartmentand close the battery coverAAAAAAAAASetting7. Light on/off switch. 8. Volume control. 9. Mode control. 10. Sensor input jack11. Anti-take off Cover12 Cover lockInstallationNurse Call ButtonChair PadChair PadplugUnlock lockUnlock and slide out the cover to install the plugSlide the switches inside the battery cover for your needs.1. Power Switch to off position when do not use this device.2. Transmitter On/Off switch On : Send a trigger signal to receiver when triggered Off : Do not send signal to receiver when triggered.3. Sound selector Select the suitable sound by slide this switch to or position..4. Light On/Off Turn the flash light on or off by slide this switch.5. Mode Mat (Fall mat): This mode for fall mat or entry mat. The unit triggered when someone step on the mat. Pad (Bed Pad): This mode for seat pad or bed pad. The unit triggered when Patients or elderly leave the pad. Pad +3S (Pad & 3 seconds delay): Same as Pad mode but delay 3 seconds for reduce False alarms.6. Volume control You can select High II / Low I / No sound by slide this switch.7 Regenerate a new code If the RF code is conflict, press the button in the pin hole to regenerate a new code13 Flasher14. Speaker15 LED indicator.16. Test /Reset button17. External DC jack18. Nurse call button jack.1234567EXITPairing with receiverOperationThis unit can work stand alone or work with the wireless receiver. If work with the receiver, you need to pairing with the receiver follow to the manual of the receiver.VelcroMat modeThe sensor unit will be triggered when someone step on the mat.Pad mode when the person lying (sitting) on the sensor pad. The sensor unit will generate a beep tone to confirm the pad is function. The unit will be triggered when Patients or elderly leave the pad sensor. Alarm will stop when the person return to the pad or press the stop button.Delay ModeFunctions are same as Pad mode, but delay 3 seconds after triggered for reduce False alarms.Nurse callPress the nurse button once (the big nurse call button must be plug in), the sensor unit will be send a trigger signal to receiver, and sensor unit will generate beep tone to indicate this button is pressed.RRRModeMatPad+3SIIITest & Reset- Test: Press the test/Reset button once, The unit will generate a beep tone, LED will blink and will send a RF to the receiver (It will depend on the function switch setting) - Reset: When the alarm is triggered, press the test/Reset thrice within 2 seconds will stopOr Using a 5V/ 300mA AC/DC adaptor5V AC/DC adaptor(Switching mode)

Navigation menu