Visiplex VTX1 Radio Transceiver User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3581211
Application ID	rCNqgFu2v7ceNgvE/wBoqg==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	3.76kB (47020 bits)
Date Submitted	2017-09-26 00:00:00
Date Available	2017-09-26 00:00:00
Creation Date	2017-09-21 13:03:08
Producing Software	Acrobat Distiller 9.0.0 (Windows)
Document Lastmod	2017-09-21 13:03:08
Document Title	Users Manual

VTX-1 Radio Transceiver - User Manual
The VTX-1 radio transceiver is designed to receive and transmit wireless analog & digital data and is designed to be used in
VISIPLEX products (such as paging encoders, data repeaters, wireless intercom controllers, etc.). The VTX-1 is typically
mounted inside the VISIPLEX host product and connected to its controller board using the Data & Power Interface 8-pin
cable. The VTX-1 unit is fully contained and no external adjustments are provided.
Programming of the VTX-1 parameters is performed via the USB port using commands sent via the PC serial port to the
VTX-1 host controller. The serial commands are sent using serial communication utilities such as HyperTerminal.
After programming is completed and the VTX-1 is mounted in to the VISIPLEX product, the USB port is not accessible to the
typical end user.
Note: The programming commands are available only to in-house radio technicians or external radio professionals familiar
with FCC restrictions under KDB 594280 to ensure compliance with FCC regulations.
Licensing
Some frequency bands governed by FCC rules require that the radio owner obtain a station license before using the
equipment to transmit. The station license holder is also responsible for the proper operation and maintenance of the VTX-1.
Note: The host end product label must include the following text: "Contains FCC ID: 2AAFWVTX1"
Safety
Please refer to RF Radiation Hazard Warning under Notice to User Regarding Radio Frequency Interference section for
information regarding RF radiation and recommended operation guidelines.
Version: 1.00
Typical Installation (Host product)
1. Mount the VTX-1 in the host product enclosure
2. Secure the VTX-1 using the applicable bracket and connect the Data & Power Interface cable to the host product main
board
Version: 1.00
3. Complete final assembly of host product. Verify connectivity and test for proper operation.
Version: 1.00
Specifications
Frequency Range
406.1 - 470 MHz
Channel Spacing
12.5 kHz
Frequency Control
PLL
Frequency Stability
2.5 ppm
RF Power Output
19.4 dBm
RF Output Connector
BNC
RF Input Connector
SMA
RF Load Impedance
50 Ohms
Recommended Antenna
3 dBi, Omni-Directional, Vertical Polarization
Power
5 VDC 1A
Power & Data Interface
8 Pin / USB Type B
Approvals
FCC: 2AAFWVTX1
Operating Temperature
14ยบ to 122ยบ F / -10ยบ to 50ยบ C
Dimensions (W x H x D)
4" x 2.125" x 0.75" / 102mm x 54mm x 19mm (Connectors Included)
Weight
0.2 lbs.
Data & Power Interface Pin Out
1 - DC POWER (5V Input)
2 - PTT (Push to Talk Input)
8 7 6 5 4 3 2 1
3 - DATA IN (Data/Audio Input)
4 - RX (Digital Data Input)
5 - DATA OUT (Data/Audio Output)
6 - DCD (Carrier Detect Output)
7 - TX (Digital Data Output)
8 - GND (Ground)
Notice to User Regarding Radio Frequency Interference (Class B)
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must accept any interference received, including interference that
may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority
to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try
and correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and the receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
RF Radiation Hazard Warning: To ensure compliance with FCC RF exposure requirements, the recommended minimum
lateral distance from the transmitting antenna is 30 cm from your body or nearby persons during continuous use.
Version: 1.00

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : 
Create Date                     : 2017:09:21 13:03:08-05:00
Modify Date                     : 2017:09:21 13:03:08-05:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00
Producer                        : Acrobat Distiller 9.0.0 (Windows)
Format                          : application/pdf
Creator                         : 
Title                           : 
Document ID                     : uuid:c33bb26b-e12f-4fbd-8297-9c5a1e8d0806
Instance ID                     : uuid:fa366673-d674-4352-86c1-1a4520d49225
Page Count                      : 4

EXIF Metadata provided by EXIF.tools