Voxx Electronics DEI471A Transmitter Keyfob User Manual Blister Card Automate 471A 01 05

DEI Headquarters, Inc. Transmitter Keyfob Blister Card Automate 471A 01 05

manual

Replacement TransmitterHigh Frequency, Motion Activated RemotePP//NN 447711AACompatible with thefollowing SmartStarter Kill systems:AAuuttoommaattee 66440011AAAAuuttoommaattee 66440022AAAAuuttoommaattee 66440033AAAAuuttoommaattee 66440044AAAAuuttoommaattee 66440066AAAAuuttoommaattee 66440077AAAAuuttoommaattee 66441111AAAAuuttoommaattee 66441122AAAAuuttoommaattee 66441133AAAAuuttoommaattee 66441144AA
MADE IN CHINA©2005 Directed Electronics, Inc. Vista CA 92081All rights reserved.P/N 471A 01/05Starter Kill System Learn Procedure1. Key Start. Turn the key to the the start position. Ifthe vehicle does not start then proceed to step 3.If the vehicle starts then the starter kill system isnot armed. Proceed to step 2.2. Key Off. Turn key off and wait for 40 seconds. Turnthe key to the start position and the vehicle shouldnot start.3. Cycle. Turn the key OFF and then cycle the keyfrom off to start position 3-times within 5 secondsand then hold in the start position on the 4th turn.4. Learn. Press the button labeled "Automate" on thetransmitter within 5 seconds (the starter cranks).Repeat steps above to learn up to a total of 4transmitters.5. Test.Turn the key OFF and wait 40 seconds. Turn thekey to start, the vehicle should not start.Shake the transmitter to transmit disarm signal.turn the key to start, the vehicle should crank andstart. If this procedure does not work, press thebutton labeled "Automate" and try again.Ignition Kill System Learn Procedure1. Key. Turn the key to the ignition position. If poweris present, then the ignition kill system is notarmed. If no power is present proceed to step 3.2. Key Off. Turn the key OFF and wait 40 seconds.Turn the key to Ignition position again. Powershould be present.3. Cycle. Turn the key OFF and then cycle the keyfrom off to ignition position 3-times within 5seconds, and then hold in the ignition position onthe 4th turn.4. Learn. Press the button labeled "Automate" on thetransmitter within 5 seconds (ignition has power).Repeat steps above to learn up to a total of 4transmitters.5. Test.Turn the key OFF and wait 40 seconds. Turn thekey to ignition position. The ignition should nothave power.Shake the transmitter to transmit disarm signal.turn the key to start, the vehicle should crank andstart. If this procedure does not work, press thebutton labeled "Automate" and try again.Motion Sensor ProceduresTransmitter will ship from the factory with motion sen-sor de-activated.Activation Procedure1. Press and HOLD the button. The LED will go offand then flash 2 times.2. Release the button. The Motion sensor is nowactive.Deactivation Procedure1. Press and release the button 2 times.2. Within 5 seconds, press and HOLD the button.The LED will go off and then flash 4 times.3. Release the button. The Motion sensor is nowdeactived.*If the LED does not flash as specified above, theprocedure should be done again. Wait at least 5seconds before starting procedure again.FCC/ID NoticeThis device complies with Part 15 of FCC rules.Operation is subject to the following conditions: (1) Thisdevice may not cause harmful interference, and (2) Thisdevice must accept any interference received, includinginterference that may cause undesired operation.CAUTION! Changes or modifications not expresslyapproved by the party responsible for compli-ance could void the user's authority to oper-ate this device.REPLACEMENT TRANSMITTERModel 471A, Single Button, Motion Activated RemoteThe following Learn Routine can be used to programthis replacement transmitter to the system. Refer to theowner’s wallet card to find which system (ignition orstart) was installed).

Navigation menu