Voxx Electronics DEI471A Transmitter Keyfob User Manual Blister Card Automate 471A 01 05
DEI Headquarters, Inc. Transmitter Keyfob Blister Card Automate 471A 01 05
manual
Replacement Transmitter
High Frequency, Motion Activated Remote
PP//NN 447711AA
Compatible with the
following Smart
Starter Kill systems:
AAuuttoommaattee 66440011AA
AAuuttoommaattee 66440022AA
AAuuttoommaattee 66440033AA
AAuuttoommaattee 66440044AA
AAuuttoommaattee 66440066AA
AAuuttoommaattee 66440077AA
AAuuttoommaattee 66441111AA
AAuuttoommaattee 66441122AA
AAuuttoommaattee 66441133AA
AAuuttoommaattee 66441144AA
MADE IN CHINA
©2005 Directed Electronics, Inc. Vista CA 92081
All rights reserved.
P/N 471A 01/05
Starter Kill System Learn Procedure
1. Key Start. Turn the key to the the start position. If
the vehicle does not start then proceed to step 3.
If the vehicle starts then the starter kill system is
not armed. Proceed to step 2.
2. Key Off. Turn key off and wait for 40 seconds. Turn
the key to the start position and the vehicle should
not start.
3. Cycle. Turn the key OFF and then cycle the key
from off to start position 3-times within 5 seconds
and then hold in the start position on the 4th turn.
4. Learn. Press the button labeled "Automate" on the
transmitter within 5 seconds (the starter cranks).
Repeat steps above to learn up to a total of 4
transmitters.
5. Test.
Turn the key OFF and wait 40 seconds. Turn the
key to start, the vehicle should not start.
Shake the transmitter to transmit disarm signal.
turn the key to start, the vehicle should crank and
start. If this procedure does not work, press the
button labeled "Automate" and try again.
Ignition Kill System Learn Procedure
1. Key. Turn the key to the ignition position. If power
is present, then the ignition kill system is not
armed. If no power is present proceed to step 3.
2. Key Off. Turn the key OFF and wait 40 seconds.
Turn the key to Ignition position again. Power
should be present.
3. Cycle. Turn the key OFF and then cycle the key
from off to ignition position 3-times within 5
seconds, and then hold in the ignition position on
the 4th turn.
4. Learn. Press the button labeled "Automate" on the
transmitter within 5 seconds (ignition has power).
Repeat steps above to learn up to a total of 4
transmitters.
5. Test.
Turn the key OFF and wait 40 seconds. Turn the
key to ignition position. The ignition should not
have power.
Shake the transmitter to transmit disarm signal.
turn the key to start, the vehicle should crank and
start. If this procedure does not work, press the
button labeled "Automate" and try again.
Motion Sensor Procedures
Transmitter will ship from the factory with motion sen-
sor de-activated.
Activation Procedure
1. Press and HOLD the button. The LED will go off
and then flash 2 times.
2. Release the button. The Motion sensor is now
active.
Deactivation Procedure
1. Press and release the button 2 times.
2. Within 5 seconds, press and HOLD the button.
The LED will go off and then flash 4 times.
3. Release the button. The Motion sensor is now
deactived.
*If the LED does not flash as specified above, the
procedure should be done again. Wait at least 5
seconds before starting procedure again.
FCC/ID Notice
This device complies with Part 15 of FCC rules.
Operation is subject to the following conditions: (1) This
device may not cause harmful interference, and (2) This
device must accept any interference received, including
interference that may cause undesired operation.
CAUTION! Changes or modifications not expressly
approved by the party responsible for compli-
ance could void the user's authority to oper-
ate this device.
REPLACEMENT TRANSMITTER
Model 471A, Single Button, Motion Activated Remote
The following Learn Routine can be used to program
this replacement transmitter to the system. Refer to the
owner’s wallet card to find which system (ignition or
start) was installed).