Voxx Electronics DEI471A Transmitter Keyfob User Manual Blister Card Automate 471A 01 05

Download:
Mirror Download [FCC.gov]
Document ID	507369
Application ID	gSVy+Pd/0Vd+/FquFH7f1w==
Document Description	manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	15.33kB (191639 bits)
Date Submitted	2005-01-19 00:00:00
Date Available	2005-02-15 00:00:00
Creation Date	2005-01-14 10:43:42
Producing Software	Acrobat Distiller 6.0.1 (Windows)
Document Lastmod	2005-01-14 10:43:42
Document Title	Blister Card, Automate 471A 01-05.qxd
Document Creator	PScript5.dll Version 5.2.2
Document Author:	Paul.Wisiolek

Replacement Transmitter
High Frequency, Motion Activated Remote
P/N 471A
Compatible with the
following Smart
Starter Kill systems:
Automate 6401A
Automate 6402A
Automate 6403A
Automate 6404A
Automate 6406A
Automate 6407A
Automate 6411A
Automate 6412A
Automate 6413A
Automate 6414A
REPLACEMENT TRANSMITTER
Model 471A, Single Button, Motion Activated Remote
The following Learn Routine can be used to program
this replacement transmitter to the system. Refer to the
1.
2.
3.
4.
5.
Starter Kill System Learn Procedure
Key Start. Turn the key to the the start position. If
the vehicle does not start then proceed to step 3.
If the vehicle starts then the starter kill system is
not armed. Proceed to step 2.
Key Off. Turn key off and wait for 40 seconds. Turn
the key to the start position and the vehicle should
not start.
Cycle. Turn the key OFF and then cycle the key
from off to start position 3-times within 5 seconds
and then hold in the start position on the 4th turn.
Learn. Press the button labeled "Automate" on the
transmitter within 5 seconds (the starter cranks).
Repeat steps above to learn up to a total of 4
transmitters.
Test.
Turn the key OFF and wait 40 seconds. Turn the
key to start, the vehicle should not start.
Shake the transmitter to transmit disarm signal.
turn the key to start, the vehicle should crank and
start. If this procedure does not work, press the
button labeled "Automate" and try again.
Motion Sensor Procedures
Transmitter will ship from the factory with motion sensor de-activated.
Activation Procedure
1. Press and HOLD the button. The LED will go off
and then flash 2 times.
2. Release the button. The Motion sensor is now
active.
Deactivation Procedure
1. Press and release the button 2 times.
2. Within 5 seconds, press and HOLD the button.
The LED will go off and then flash 4 times.
3. Release the button. The Motion sensor is now
deactived.
owner’s wallet card to find which system (ignition or
start) was installed).
1.
2.
3.
4.
5.
Ignition Kill System Learn Procedure
Key. Turn the key to the ignition position. If power
is present, then the ignition kill system is not
armed. If no power is present proceed to step 3.
Key Off. Turn the key OFF and wait 40 seconds.
Turn the key to Ignition position again. Power
should be present.
Cycle. Turn the key OFF and then cycle the key
from off to ignition position 3-times within 5
seconds, and then hold in the ignition position on
the 4th turn.
Learn. Press the button labeled "Automate" on the
transmitter within 5 seconds (ignition has power).
Repeat steps above to learn up to a total of 4
transmitters.
Test.
Turn the key OFF and wait 40 seconds. Turn the
key to ignition position. The ignition should not
have power.
Shake the transmitter to transmit disarm signal.
turn the key to start, the vehicle should crank and
start. If this procedure does not work, press the
button labeled "Automate" and try again.
* If the LED does not flash as specified above, the
procedure should be done again. Wait at least 5
seconds before starting procedure again.
FCC/ID Notice
This device complies with Part 15 of FCC rules.
Operation is subject to the following conditions: (1) This
device may not cause harmful interference, and (2) This
device must accept any interference received, including
interference that may cause undesired operation.
CAUTION! Changes or modifications not expressly
approved by the party responsible for compliance could void the user's authority to operate this device.
P/N 471A
01/05
MADE IN CHINA
© 2005 Directed Electronics, Inc. Vista CA 92081
All rights reserved.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 2
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:801b14f0-3767-4ed5-a1f0-eaf1a1100b31
Producer                        : Acrobat Distiller 6.0.1 (Windows)
Create Date                     : 2005:01:14 10:43:42-08:00
Creator Tool                    : PScript5.dll Version 5.2.2
Modify Date                     : 2005:01:14 10:43:42-08:00
Document ID                     : uuid:1f1eec86-7cb4-4544-b311-4aee6fce7ade
Format                          : application/pdf
Title                           : Blister Card, Automate 471A 01-05.qxd
Creator                         : Paul.Wisiolek
Author                          : Paul.Wisiolek

EXIF Metadata provided by EXIF.tools