Voxx Electronics DEI7752 Hand Held Security/Remote Control Transceiver User Manual page 31 to 54

Download:
Mirror Download [FCC.gov]
Document ID	961945
Application ID	ohw1hikPYSz/zWvtFqKM8g==
Document Description	user manual page 31 to 54
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	103.17kB (1289671 bits)
Date Submitted	2008-06-27 00:00:00
Date Available	2008-06-30 00:00:00
Creation Date	2008-06-27 14:33:28
Producing Software	Adobe PDF Library 8.0
Document Lastmod	2008-06-27 14:33:47
Document Title	user manual page 31 to 54
Document Creator	Adobe InDesign CS3 (5.0.2)

•
•
If the alarm is triggered when armed.
When the Remote Start command is sent again from a remote 		
control
➤ Runtime Check
To check the amount of runtime remaining (2 way remote only):
AUX
After the vehicle is remote started, press the
button three-times and
then hold until the remote beeps, and then release. The display will
show a text indicating remaining run time.
➤ Manual transmission
If the vehicle has manual transmission the proper steps must be followed before leaving the parked vehicle or the remote start feature is
disabled.
1.
2.
3.
4.
5.
6.
7.
8.
9.
Put the transmission in neutral.
Press on the vehicle’s foot brake.
Apply the emergency brake.
Release the vehicle’s foot brake. Note: Pressing the brake again
after this step will disable the remote start feature.
Within 15 seconds activate the remote start from the remote.
The parking lights will flash 5 times confirming that the remote start
is active.
Turn off the ignition (the car should stay running when key is turned
off).
Exit the vehicle and close the door.
Arm the alarm (the vehicle should shut off when arming the system).
You can now remote start the vehicle. If a door is opened or if the alarm
Š 2008 Directed Electronics. All rights reserved.
31
is triggered before the next remote start activation the system will not
remote start.
To drive your vehicle after it has been remote started:
1. Get in without stepping on the brake.
2. Insert the ignition key and turn it to the ON position.
3. Now, step on the brake.
The remote control will play the remote start shutdown tone. You have
now taken direct control from the remote start system.
➤ Timer mode
To activate the runtime of the vehicles engine during remote start:
AUX
1.
2.
3.
Press the
button two-times and then
The vehicle will confirm with 4 fast parking light flashes.
The system will start every 3 hours until canceled by the brake,
hood, or neutral safety shut-down wires. The remote will respond
with the Start and Stop remote start notification during each Start
and Stop of the Vehicle while in Timer mode.
AUX
Important! Timer Mode should be used only in open areas. Never
start and run the vehicle in an enclosed space such as a garage or
carport.
AUX
To exit timer mode, Press the
button two-times and then
again.
AUX
➤ Turbo timer mode
Turbo timer mode keeps the engine running after arriving at your destination for a programmable period of 1, 3, 5 or 10 minutes. This allows
the system’s timer to conveniently cool down the turbo after you have
32
Š 2008 Directed Electronics. All rights reserved.
left the vehicle.
Transmit the timer mode feature with the remote while the engine is running, press
two-times and then
. After exiting the vehicle, arm the
alarm and the vehicle will remain running for the programmed runtime.
(The remote start feature is still enabled).
AUX
AUX
The system monitors the engine speed and will automatically shut the
engine off if the RPMs rise above or fall below the programmed levels.
This feature prevents damage to the motor due to fuel delivery system
failures or other problems which may cause the engine to race.
Note: To enter turbo timer mode with a manual transmission, perform
the manual transmission procedure (See p.29), with the door open.
Rear defogger
The rear defogger (if connected) is programmed to automatically activate when remote start is turned on. If the interior cabin temperature is
above 55˚ F the defogger will not activate.
To manually activate the rear defogger after remote start is on:
AUX
Press
four times, and then
Valet take-over
The Valet take-over feature allows the vehicle to remain running after
the key has been removed from the ignition. This feature is useful for
occasions when you wish to exit and lock the vehicle for short periods
of time, but would like to leave the motor running and the climate
controls on.
Š 2008 Directed Electronics. All rights reserved.
33
To perform Valet take-over:
1. Before turning off the engine, press and release
on the transmitter. Then wait a few seconds.
2. Turn the ignition key to the OFF position (The engine will stay
running).
3. The engine will run until the pre-programmed time elapses or a
shut-down input is received.
Note: To enable Valet take-over with a manual transmission, open
the door when going into a manual transmission mode. After you
exit the vehicle you can arm the alarm and the car will remain running. If the vehicle shuts down when arming, then the unit did not
enter the valet take-over mode.
34
Š 2008 Directed Electronics. All rights reserved.
Safety features
This system has several important safety features to ensure proper operation of the motor and prevent accidental damage to the engine or
its components.
➤ Starter anti-grind circuitry
Whenever the vehicle is remote started, advanced anti-grind circuitry
prevents the starter from engaging, even if the key is turned to the start
position. This prevents damage to the starter motor if the key is turned
to the start position during remote start operation.
Note: Anti-grind circuitry only works when the remote start system is
operating the motor and the FailsafeÂŽ Starter Kill relay is installed.
➤ Disabling the remote start system
This feature allows the remote start unit to be temporarily disabled
to prevent the vehicle from being remote started accidentally. This
feature is useful when the vehicle is being serviced or stored in an
enclosed area.
To disable the remote start, move the shutdown toggle switch to the
OFF position. Check with your installer for the location.
Location of Shutdown Switch____________________________
Š 2008 Directed Electronics. All rights reserved.
35
Diagnostics
The microprocessor at the heart of your system is constantly monitoring
all of the switches and sensors connected to it. It is designed to detect
any faulty switches and sensors and prevent them from disabling the
entire system. The microprocessor will also record and report any triggers that occurred during your absence.
Refer to System Status Chirps and Table of Zones sections of this guide
for diagnostic information.
➤ Arming
If the security system is armed at the same time that an input is active
(such as a door opening or sensor triggering), you will hear one siren
chirp to indicate arming and a second siren chirp to indicate Bypass
Notification.
A Bypass Notification chirp means that the security system ignores
the input that was active when the system was armed, until that input
ceases. Three seconds after that input ceases, the security system will
resume normal monitoring.
For example: if your vehicle has an interior light exit delay and you arm
your security system before the interior light turns off, you may hear a
second Bypass Notification chirp.
Once the light turns off, however, the security system resumes normal
monitoring.
Note: Bypass Notification does not occur when the system is in Silent
Mode or if the notification chirps have been programmed off by the
installer.
36
Š 2008 Directed Electronics. All rights reserved.
➤ Disarming
Extra chirps heard when disarming the system are the Tamper Alert.
If four chirps are heard when disarming the system, then the security
system was triggered in your absence.
If five chirps are heard when disarming the system, the system was
triggered so many times that the Nuisance ProtectionÂŽ Circuitry has
bypassed the intended zone. In either case, the status LED will indicate
which zone was involved (see Table of Zones).
The security system will retain this information in its memory, and chirp
four or five times each time it is disarmed, until the next time that the
ignition is turned on.
➤ System status chirps
The siren will chirp when arming/disarming the system. The pattern of
chirps will audibly report the system’s status as described below.
Action
Number of Chirps
Description
Arm
System armed
Arm
1 (3-second delay)
System armed with bypass notification
Disarm
System armed
Disarm
System disarmed with Tamper Alert
Disarm
System disarmed
Š 2008 Directed Electronics. All rights reserved.
37
➤ Table of zones
A zone is represented by the number of LED flashes used by the system
to identify a particular type of input. Standard input assignments are
listed in the following table, along with spaces to write in any optional
sensors or switches that have been installed.
Zone
Description
Dealer installed options
Trunk Pin
Instant trigger: a heavier impact
detected by the shock sensor
Door switch trigger
Instant trigger: For optional
sensors
Ignition trigger
Hood Pin
➤ Interpreting zone diagnostics
Warn Away responses are not reported by arming or disarming diagnostics. If you receive a Bypass notification when arming or a Tamper
Alert notification when disarming, look at the LED.
Active or triggered zones will be indicated by a pattern of blinks by
the LED.
For example: If zone 3 was active or triggered, the LED will blink three
times with a two-second pause. Then it will blink three times again, and
repeat until the ignition is turned on.
38
Š 2008 Directed Electronics. All rights reserved.
➤ Nuisance prevention® circuitry
Your system has Directed’s Nuisance Prevention® Circuitry (NPC). It
prevents annoying repetitive trigger sequences due to faulty door pin
switches or environmental conditions such as thunder, jackhammers,
airport noise, etc.
For example: If the alarm triggers three times within a 60-minute period
and each time the same sensor or switch triggers the alarm, NPC will
interpret those triggers as false alarms. After the third trigger, NPC ignores, or bypasses, that sensor or switch (along with any other sensors
or switches sharing the same zone) for 60 minutes.
If the bypassed sensor tries to trigger the security system while it is being
bypassed, the 60-minute bypass period will start over. This ensures that
a sensor that is continually being triggered will remain bypassed.
The vehicle doors are protected by NPC differently. If your security
system is triggered by an open door for three full cycles, the system will
bypass the doors until the trigger ceases.
Š 2008 Directed Electronics. All rights reserved.
39
Owner recognition
Owner Recognition lets up to four users of the system have unique settings that meet their specific needs. It is almost like having four separate
alarms in your vehicle, one for each user. This feature is only available
to authorized dealers using the Bitwriter or Bitwriter 2 program tool.
Rapid resume logic
This Directed system will store its current state to non-volatile memory.
If power is lost and then reconnected the system will recall the stored
state from memory.
For example, if the unit is in Valet Mode and the battery is disconnected
for any reason, such as servicing the car, when the battery is reconnected the unit will still be in Valet Mode. This applies to all states of the
system including arm, disarm, and Valet Mode.
40
Š 2008 Directed Electronics. All rights reserved.
Power saver mode
➤ System
Your system will automatically enter Power Saver Mode while armed or
in Valet Mode, after a period of time in which no operation has been
performed. This lowers the current draw on the vehicle’s battery. Power
Saver Mode takes over under the following conditions:
Power Saver when the system is armed: After the system has been
armed for 24 hours the LED will flash at half its normal rate, decreasing
the system’s current draw.
Power Saver in Valet Mode: When the system enters Valet Mode the
Status LED on the Responder LE control center illuminates steadily. If the
vehicle is not used (ignition is not turned on) for a one hour period while
the system is in Valet Mode, the status LED will shut off. If the system
remains in Valet Mode, the LED will come back on the next time the
ignition is turned on and then back off.
➤ 2-way remote
Your Responder LE 2way remote control has a feature called remote
power save mode. When programmed ON under remote options, the
remote will conserve power by disabling the paging function if unused
for more than 72 hours. Pressing any button on the remote will restore
the paging function.
The default setting is ON. See Remote control programming section of
this guide or ask your dealer for details on how to program.
Š 2008 Directed Electronics. All rights reserved.
41
Programming options
Your system has many custom programmable options. Some may require installation labor. Ask your authorized dealer for details.
The following is a list of the programmable options, with the factory
settings in Bold.
•
Active arming (remote only) passive arming with or without locking
the doors (automatic arming without locking the doors 30 seconds
after the last door has been closed), or Auto Re-arm with or without
locking the doors (Automatically arms 60 seconds after disarm if
no door is opened).
Arming/disarming siren chirps ON with or without Warn-away chirps,
Or OFF with or without Warn-away chirps.
•
Ignition controlled door lock feature ON or OFF: When this feature is programmed on, the doors will lock three seconds after the
ignition is turned on, and unlock when the ignition is turned off.
If your installer is programming the security system with the Directed
BitwriterÂŽ, ignition lock and unlock are independent features that can
be programmed separately.
•
Panic mode enabled/disabled when the ignition is turned on or
completely turned OFF. (Some states have laws against sirens
sounding in moving cars.)
•
Full trigger response 30 or 60 seconds: This determines how long
the full triggered sequence lasts. Some states have laws regulating
42
Š 2008 Directed Electronics. All rights reserved.
•
how long a security system can sound before it is considered a
nuisance.
If your installer is programming the security system with the Directed BitwriterÂŽ, the full triggered response can be programmed
for any duration ranging from 1 to 180 seconds.
•
Siren tones and chirp volume: The output of the Revenger™Soft
Chirp™ siren consists of six different tones in sequence. Any of
these tones can be eliminated by a dealer, resulting in a unique,
easily identifiable siren sound. The chirps can be either full volume
or 6 decibels quieter than the full alarm blast.
•
Comfort closure is a programming option which closes the vehicle’s windows after remote locking.
Š 2008 Directed Electronics. All rights reserved.
43
Security & convenience expansions
Listed below are some of the many expansion options available. Please
consult your dealer for a complete explanation of all the options available to you.
Audio Sensor: Metal on glass, glass cracking, and breaking
glass produce distinctive acoustic signatures. The 506T audio sensor
uses a microphone to pick up sounds, then analyzes them with proprietary acoustic software to determine if the glass has been struck.
Backup Battery: The 520T keeps the system armed, triggers the alarm
and keeps the starter interrupt active if main battery is disconnected.
Digital Tilt Sensor: The 507M tilt sensor can be added to your system
to protect your car when its parked. It can protect your vehicle from being lifted and provide protection for your expensive rims.
Field Disturbance Sensor: An invisible dome of coverage is established
by installing the 508D “radar” sensor. Your system can react to any
intrusions into this field with the full triggered sequence.
Power Locks: This system offers lock outputs that can control some manufacturers’ power door lock systems. For other systems, additional parts
may be required.
Hood Lock: Prevents the vehicle’s hood from being opened without a
key, keeping thieves away from the system’s siren, the battery connections, and other components under the hood.
Power Trunk Release: The accessory output of the system can operate
a factory power release for the vehicle’s trunk or hatch. Although the
44
Š 2008 Directed Electronics. All rights reserved.
on-board relay can control most power trunk releases, sometimes an
optional relay is required. If the factory release is not power-activated,
Directed®’s 522T trunk release solenoid can often be added.
Power Window Control: Automatic power window control is provided
with the 529T and 530T systems. These can operate power windows,
and can roll them up automatically when the system is armed, roll them
down, or both up and down.
Ultrasonic Cabin Sensor: Using the 509U Ultrasonic cabin sensor provides a field of protection inside the car to protect your belongings.
Š 2008 Directed Electronics. All rights reserved.
45
Glossary of terms
2-Way Remote: A hand-held, remote control which operates the
various functions of your system and receives feedback and pages from
the alarm system.
Control Center: The control center contains the system’s radio-frequency
antenna, the valet and override switch, and the Status LED.
For maximum remote-control range, the Control Center is usually located at the top of the windshield, centered near the rear-view mirror.
Control Module: The “brain” of your system. Usually hidden underneath
the dash area of the vehicle. It houses the microprocessor which monitors your vehicle and controls all of the alarm’s Functions.
FailsafeÂŽ Starter Kill (if equipped): An automatic switch controlled by
the security system which prevents the vehicle’s starter from cranking
whenever the system is armed. The vehicle is never prevented from
cranking when the system is disarmed, in ValetÂŽ Mode, or should the
starter kill switch itself fail. Your system is ready for this feature, however
installation of this feature may require additional labor.
Input: Any physical connection to the security system. An input can
be provided through a sensor, pin-switch or by existing systems in the
vehicle, such as ignition or courtesy lights.
In-vehicle status LED: A light used to indicate the status of your system.
It is located on your systems control center.
Shock Sensor: This system has a dual zone shock sensor. This
sensor is mounted in the vehicle and designed to pick up impacts
46
Š 2008 Directed Electronics. All rights reserved.
to the vehicle or glass.
Trigger or Triggered Sequence: This is what happens when the
alarm “goes off ” or “trips.” The triggered sequence of your
system consists of the siren sounding and parking lights flashing
for the programmed duration.
Valet Button: A small push button switch located on your systems control
center. It is used to override the
starter interrupt when a 2-way remote is lost or damaged, or to
enter or exit Valet Mode.
Warn AwayÂŽ Response: Light impacts to the vehicle generate the
Warn AwayÂŽ Response, which consists of several seconds of horn
honks and flashing parking lights.
Zone: A zone is a separate input that the alarm can recognize as
unique. Each input to the system is connected to a particular zone.
Often, two or more inputs may share the same zone.
Š 2008 Directed Electronics. All rights reserved.
47
48
Š 2008 Directed Electronics. All rights reserved.
✂
Quick reference guide
Arming
To arm, press
. When the system arms, the LOCK LED blinks for
one second, with 1 beep and siren tone.
Cut along the dotted line and fold to keep in purse or wallet for a quick and easy reference.
AUX
Arming while driving
To arm the system while driving, press
on your remote while the
vehicle is running. The LOCK LED blinks for one second.
AUX
Disarming
To disarm, press
. The UNLOCK LED blinks for one second, and
you will hear 2 beeps.
REV.
AUX
DESCRIPTION
Disarming without a remote
Turn on the ignition. Press the Valet button within 15 seconds. The
system should now disarm. If it does not, you may have waited too
long or pressed the button incorrect number of times. Refer to reverse
side for Valet pushes and try again.
36.32
10.44
11.50
Number of Valet button pulses for disarming_______________
CA
%2'<0$7(5,$/+,+($7$%689
AUX
*Tolerance please refer specification
of tolerance limits "c"
INJECT TOLERANCE SPEC.
Silent Arm
Press
one time and then press
second with no sound.
GRADE
Âą
0.16
0.30
0.10
0.20
0.40
0.20
0.40
0.80
120~300
0.40
0.80
2.00
UNDER 6
Âą
Âą
0.08
6~30
30~120
DIMENSION
1. Texture is same as

2. Radious will be if not specified.
3. Body color :
%/$&.
SCALE:
1:1
MATERIAL
FINISH
UNIT:
M/M
DRN BY
VICTOR
APPD BY
. Arm LED will blink for one
CODE
SHEET
94I0600
AUX
✂
AUX
Silent Disarm
Press
one time and then press
second with no sound.
Š 2008 Directed Electronics. All rights reserved.
DATE
11/20/07
CHK BY
FELIX
YGF
. Disarm LED will blink for 1
AUX
49
OF
AUX
✂
Remote Start
Press
. Remote start LED blinks for 3 seconds and remote start
tone sounds.
AUX
Rear Defogger
Press
four times, and then press
(only after remote start is
ON.) Remote start LED turns ON, and you will hear 1 beep.
To disable the remote start system
Move the shutdown toggle switch to the OFF position.
Location of Shutdown Toggle Switch___________________
Valet Mode
AUX
Press
two times and then
. The UNLOCK LED and Function
LED blink and remote beeps one time. When valet Mode OFF, the
remote beeps two-times.
AUX
Valet take over
Before turning off the engine, press and release
. within 3 seconds. Then wait a few seconds.
Turn the ignition key to the OFF position.
The engine will remain running until the programmed time elapses or
a shut-down input is received.
AUX
Cut along the dotted line and fold to keep in purse or wallet for a quick and easy reference.
AUX
50
✂
Location of Valet button_________________________________
Š 2008 Directed Electronics. All rights reserved.
Limited lifetime consumer warranty
Directed Electronics. (“Directed”) promises to the original purchaser to repair or replace (at
Directed’s election) with a comparable reconditioned model any Directed unit (hereafter
the “unit”), excluding without limitation the siren, the remote transmitters, the associated
sensors and accessories, which proves to be defective in workmanship or material under
reasonable use during the lifetime of the vehicle provided the following conditions are met:
the unit was purchased from an authorized Directed dealer, the unit was professionally
installed and serviced by an authorized Directed dealer; the unit will be professionally
reinstalled in the vehicle in which it was originally installed by an authorized Directed
dealer; and the unit is returned to Directed, shipping prepaid with a legible copy of the
bill of sale or other dated proof of purchase bearing the following information: consumer’s
name, telephone number and address; the authorized dealers name, telephone number
and address; complete product description, including accessories; the year, make and
model of the vehicle; vehicle license number and vehicle identification number. All components other than the unit, including without limitation the siren, the remote transmitters
and the associated sensors and accessories, carry a one-year warranty from the date of
purchase of the same. ALL PRODUCTS RECEIVED BY DIRECTED FOR WARRANTY REPAIR
WITHOUT PROOF OF PURCHASE WILL BE DENIED. This warranty is non-transferable
and is automatically void if: the original purchaser has not completed the warranty card
and mailed it within ten (10) days from the date of purchase to the address listed on the
card; the unit’s date code or serial number is defaced, missing or altered; the unit has been
modified or used in a manner contrary to its intended purpose; the unit has been damaged
by accident, unreasonable use, neglect, improper service, installation or other causes not
arising out of defects in materials or construction. The warranty does not cover damage
to the unit caused by installation or removal of the unit. Directed, in its sole discretion, will
determine what constitutes excessive damage and may refuse the return of any unit with
excessive damage.
TO THE MAXIMUM EXTENT ALLOWED BY LAW, ALL WARRANTIES, INCLUDING
BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY, WARRANTY OF
MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NONINFRINGEMENT OF INTELLECTUAL PROPERTY, ARE EXPRESSLY EXCLUDED; AND
DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERSON OR ENTITY TO ASSUME
FOR IT ANY DUTY, OBLIGATION OR LIABILITY IN CONNECTION WITH ITS PRODUCTS.
DIRECTED DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS
OF THIRD PARTIES INCLUDING ITS AUTHORIZED DEALERS OR INSTALLERS. DIRECTED
SECURITY SYSTEMS, INCLUDING THIS UNIT, ARE DETERRENTS AGAINST POSSIBLE
THEFT. DIRECTED IS NOT OFFERING A GUARANTEE OR INSURANCE AGAINST
VANDALISM, DAMAGE OR THEFT OF THE AUTOMOBILE, ITS PARTS OR CONTENTS;
AND HEREBY EXPRESSLY DISCLAIMS ANY LIABILITY WHATSOEVER, INCLUDING
Š 2008 Directed Electronics. All rights reserved.
51
WITHOUT LIMITATION, LIABILITY FOR THEFT, DAMAGE AND/OR VANDALISM. THIS
WARRANTY DOES NOT COVER LABOR COSTS FOR MAINTENANCE, REMOVAL OR
REINSTALLATION OF THE UNIT OR ANY CONSEQUENTIAL DAMAGES OF ANY KIND.
IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY,
THE VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA.
CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN
THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED
SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED DEALER’S PURCHASE
PRICE OF THE UNIT. DIRECTED SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES
WHATSOEVER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES,
INCIDENTAL DAMAGES, DAMAGE TO VEHICLE, DAMAGES FOR THE LOSS OF TIME,
LOSS OF EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY
AND THE LIKE. NOTWITHSTANDING THE ABOVE, THE MANUFACTURER DOES OFFER
A LIMITED WARRANTY TO REPLACE OR REPAIR THE CONTROL MODULE SUBJECT TO
THE CONDITIONS AS DESCRIBED HEREIN. THIS WARRANTY IS VOID IF THE UNIT
HAS NOT BEEN PURCHASED FROM DIRECTED, OR AN AUTHORIZED DIRECTED
DEALER, OR IF THE UNIT HAS BEEN DAMAGED BY ACCIDENT, UNREASONABLE USE,
NEGLIGENCE, ACTS OF GOD, NEGLECT, IMPROPER SERVICE, OR OTHER CAUSES
NOT ARISING OUT OF DEFECT IN MATERIALS OR CONSTRUCTION.
Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. This warranty gives you specific
legal rights and you may also have other rights that vary from State to State.
This warranty is only valid for sale of product(s) within the United States of America.
Product(s) sold outside of the United States of America are sold “AS-IS” and shall have NO
WARRANTY, express or implied. This product may be covered by a Guaranteed Protection
Plan (“GPP”). See your authorized Directed dealer for details of the plan or call Directed
Customer Service at 1-800-876-0800.
Make sure you have all of the following information from your authorized Directed
dealer:
A clear copy of the sales receipt, showing the following:
Date of purchase
Your full name and address
Authorized dealer’s company name and address
Type of alarm installed
Year, make, model and color of the automobile
Automobile license number
Vehicle identification number
All security options installed on automobile
Installation receipts
920-0003 06-06
52
Š 2008 Directed Electronics. All rights reserved.
Š 2008 Directed Electronics. All rights reserved.
53
The company behind this system is Directed Electronics
Since its inception, Directed Electronics has had one purpose, to provide
consumers with the finest vehicle security and car stereo products and
accessories available. The recipient of nearly 100 patents and Innovations
Awards in the field of advanced electronic technology.
Directed is ISO 9001 registered.
Quality Directed Electronics products are sold and serviced throughout
North America and around the world.
Call (800) 274-0200 for more information about our products and services.
G5902 2008-03
Vista, CA 92081
www.directed.com
© 2008 Directed Electronics—All rights reserved

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
Linearized                      : No
Page Count                      : 24
PDF Version                     : 1.6
Has XFA                         : No
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:b9238128-fb05-45dc-a1e2-2d9d737bbcab
Modify Date                     : 2008:06:27 14:33:47-04:00
Create Date                     : 2008:06:27 14:33:28-04:00
Metadata Date                   : 2008:06:27 14:33:47-04:00
Document ID                     : uuid:3eeafc0e-5cb5-4af4-9f9b-e60a91047745
Format                          : application/pdf
Tagged PDF                      : Yes
Creator                         : Adobe InDesign CS3 (5.0.2)
Producer                        : Adobe PDF Library 8.0

EXIF Metadata provided by EXIF.tools