WINIA Electronics 7NF0008 Video Cassette Recorder User Manual 15708270 VR661HF E 01 CVR
Dongbu Daewoo Electronics Corporation Video Cassette Recorder 15708270 VR661HF E 01 CVR
Contents
- 1. User Manual 1of 2
- 2. User Manual 2 of 2
- 3. User Manual
User Manual
VCR
User’s Guide
Changing Entertainment. Again.
DV-T7D5N-QJ
15708270 (VR661HF)(E) 01 CVR 2/7/01, 4:55 PM1
This symbol indicates
"dangerous voltage" inside
the product that presents a
risk of electric shock or
personal injury.
WARNING
To reduce the risk of fire or
electric shock, do not expose
this product to rain or moisture.
To reduce the risk of electric shock, do not
remove cover (or back). No user serviceable
parts inside. Refer servicing to qualified service
personnel.
This symbol indicates
important instructions
accompanying the product.
Caution: To prevent electric shock, match wide blade
of plug to wide slot, fully insert.
Attention: Pour éviter les chocs électriques, introduire
la lame la plus large de la fiche dans la borne
correspondante de la prise et pousser jusqú au fond.
Refer to the identification/rating label located on the
back panel of your product for its proper operating
voltage.
FCC Regulations state that unauthorized changes or modifications to this
equipment may void the user’s authority to operate it.
Cable TV Installer: This reminder is provided to call your attention to
Article 820-40 of the National Electrical Code (Section 54 of the Canadian
Electrical Code, Part 1) which provides guidelines for proper grounding
and, in particular, specifies that the cable ground shall be connected to
the grounding system of the building as close to the point of cable entry
as practical.
Product Registration
Please fill out the product registration card and return it immediately. Returning the card allows us to contact
you if needed.
Keep your sales receipt to obtain warranty parts and service and for proof of purchase. Attach it here and
record the serial and model numbers in case you need them. The numbers are located on the back of the VCR.
Model No
Serial No. _______________________________________________________________________________________
Purchase Date:___________________________________________________________________________________
Dealer/Address/Phone: ___________________________________________________________________________
Important Information
DV-T7D5N-QJ
i
CAUTION
RISK OF ELECTRIC
SHOCK. DO NOT OPEN.
15708270 (VR661HF)(E) 01 CVR 2/7/01, 4:55 PM2
1
Introduction
Introduction
Key Features Overview
Your VCR is equipped with features that will add to your recording and viewing experience.
The following information summarizes a few of these features. Chapter 4 provides more
information about the rest of the VCR’s features and how to use them.
I
N
P
U
T
T
V
•
V
C
R
ON•OFF
PLAY FORWARD
RECORD STOP PAUSE
F.ADV
CLEAR MENU SPEED
TRACKING
1
4
7
2
5
8
3
6
9
0
C
H
A
N
V
O
L
V
O
L
C
H
A
N
INFO SEARCH
MUTE GO BACK
TV VCR
REVERSE
Rec Ch 36
Record Length 1:30
Press REC to set length
VCR Plus+® SILVER System
The VCR Plus+ system allows for simple timer recording programming by using
a single PlusCode® programming number found in most TV program listings.
The VCR Plus+ SILVER system simplifies timer recordings by automatically
setting up and updating the VCR’s clock and channel list for you.
Requirements: Make sure the VCR Plus+ SILVER system is active, and that Auto
Channel Search and time set features are correct.
®
This feature uses patented technology that detects and marks most commercials
on your recordings. The VCR determines where commercials are located, marks
the beginnings and ends of detected commercial segments, then easily skips
over them during playback. This feature does not erase commercials from
the tape.
®
This feature helps locate the beginning of a purchased or rented movie as well
as skip thorugh previews. You can go to the beginning of the movie, or, skip
from one preview/long commercial to the next.
Universal Back-Lit Remote Control
Description: The VCR’s remote control can operate most RCA, GE, and Proscan
TVs with no additional steps. It can be programmed to operate many other
brands of TVs. Back-lit buttons offer easier control in the dark.
Requirements: Point the remote control at the active component and press the
ON•OFF button to see if it can be operated.
Auto Clock Set
Description: The VCR automatically looks for time and date information after
most power outages as well as each time the machine is turned off. Using time
information broadcast in TV signals (if available), the VCR’s clock sets itself.
Requirements: Start Auto Clock Set using the VCR’s on-screen menus.
VCR Plus+ and PlusCode are registered trademarks of the Gemstar Development Corporation.
The VCR Plus+ system is manufactured under the license from Gemstar Development Corporation.
COMMERCIAL ADVANCE and MOVIE ADVANCE are registered trademarks of SRT, Inc.; a Jerry Iggulden invention licensed in association with Arthur D. Little Enterprises.
15708270 (VR661HF)(E) 02 Intro 2/7/01, 4:55 PM1
2
Introduction
Express Recording (XPR)
Description: XPR quickly records the remaining portion of a program already
in progress. XPR is a great way to capture the end of a sporting event that has
run into overtime or a live broadcast that runs long.
Requirements: Repeatedly press the Record button on the VCR front panel or
remote control to set the desired duration of time to record.
Pro-Tect Plus™ Locking
Description: Locks the VCR so that buttons on the front panel and remote
control won’t operate the VCR. This feature protects timer programs from
frustrating accidents such as being left on at the time of recording.
Requirements: Lock the VCR by pressing and holding the POWER button on
the remote control for six seconds. The front panel display will blink for several
seconds. The VCR unlocks by pressing and holding the POWER button on the
remote control, again for six seconds. The front panel display will blink again
and release the lock on the system.
Front Audio/Video Input Jacks
Description: The VCR has Audio/Video (A/V) input jacks on both the front and
rear of the unit (there are output jacks on the rear panel only). The front A/V
jacks make it easy to plug in an external A/V device, such as a camcorder.
Requirements: Make sure that all A/V connections are snug. To see a
connected device’s image, turn the VCR to its Video Line Input by pressing the
remote control’s INPUT button.
Hi-Fi Quality Sound
Description: When using the VCR’s A/V jacks, you can feed stereo quality
sound from your VCR to your TV or stereo. Stereo quality sound allows for two
separate channels of sound (Left and Right) to be heard.
Requirements: Using A/V jacks and cables to connect the VCR to the TV or
stereo (see page 58 for an advanced connection setup diagram).
SQPB S-VHS Quasi Playback
Description: Your VCR will be able to play back tapes recorded in S-VHS or
S-VHS-ET mode (in VHS quality).
Requirements: Insert a tape recorded in S-VHS or S-VHS-ET mode and pressing
the PLAY button on the remote control or PLAY•PAUSE on the VCR.
TIMER RECORDINGS
1 Create a New Program
2 Review Existing Progs.
3 Use VCR Plus+ Code
0 Exit
15708270 (VR661HF)(E) 02 Intro 2/7/01, 4:55 PM2
3
Table of Contents
Product Registration
............................................................................................................. i
Introduction
............................................................................................................................ 1
Key Features Overview ......................................................................................................... 1
Connections & Setup
........................................................................................................... 5
Things to Consider Before Connecting Components .......................................................... 6
Cable Considerations ............................................................................................................6
Choose Your Connection ...................................................................................................... 7
Using the RF Coaxial Cable to Connect the VCR to a TV .............................................. 7
TV + VCR .......................................................................................................................... 8
TV + VCR + Satellite Receiver ......................................................................................... 9
TV + VCR + Cable Box ................................................................................................... 10
Set the VCR’s CH 3/4 Switch ................................................................................................ 11
Plug in the VCR .................................................................................................................... 11
Put Batteries in the Remote Control .................................................................................. 11
Turn on the TV and VCR...................................................................................................... 11
Tune the TV.......................................................................................................................... 11
Using the Remote Control to Navigate On-Screen Menus ............................................... 12
Complete the QuickSet Guide ...................................................................................... 12
Accessing Menus ........................................................................................................... 12
VCR Basics ............................................................................................................................ 13
Playing a Tape ............................................................................................................... 13
Automatic Rewind ........................................................................................................ 13
Tape Eject ......................................................................................................................13
Recording ............................................................................................................................. 13
Check the Safety Tab .................................................................................................... 13
Using the VCR’s Menu System
....................................................................................... 15
Using On-Screen Menus to Set Up Features ...................................................................... 16
Language ....................................................................................................................... 16
Cable Box Setup ............................................................................................................ 16
VCR Channels List.......................................................................................................... 17
Auto Channel Searching ....................................................................................... 17
Changing the Signal Type ..................................................................................... 18
Adding or Removing Channels ............................................................................. 18
Time and Date ............................................................................................................... 19
Auto Clock Set Feature.......................................................................................... 19
To Turn Auto Clock Set ON .............................................................................. 19
Setting the Time Zone ..................................................................................... 19
Setting Daylight-Saving Time .......................................................................... 20
Setting Time and Date Manually .......................................................................... 20
Additional Set Up Features in the Preferences Menu ....................................................... 21
Remote VCR1/VCR2 Option .......................................................................................... 21
Auto Play .......................................................................................................................21
Auto TV/VCR.................................................................................................................. 22
EnergySaver................................................................................................................... 22
Front Panel Brightness (VCR Display) .......................................................................... 22
Tape Speed .................................................................................................................... 23
Set Auto Repeat ............................................................................................................ 23
15708270 (VR661HF)(E) 03 ToC 2/7/01, 4:55 PM3
Table of Contents
4
Using the Remote Control
............................................................................................... 25
Remote Control Buttons ..................................................................................................... 26
Component Buttons ..................................................................................................... 26
VCR Function Buttons ................................................................................................... 26
TV Function Buttons ..................................................................................................... 27
Using the INPUT Button ........................................................................................ 28
Operating a TV with the VCR’s Remote Control ............................................................... 28
Do You Need to Program the Remote? ....................................................................... 28
Using the VCR’s Features
.................................................................................................. 31
Recording Features ............................................................................................................. 32
Express Recording (XPR) ............................................................................................... 32
Timer Recording ............................................................................................................ 33
Stopping a Timer Recording ................................................................................. 33
Reviewing and Clearing Programs ....................................................................... 33
VCR Plus+ SILVER System .............................................................................................. 34
Turning ON or OFF the Auto VCR Plus+ download ............................................. 34
Mapping VCR Plus+ Channels Manually .............................................................. 35
Recording Broadcast Stereo TV or SAP (Second Audio Program) ...................... 38
Copying and Editing Tapes Using Two VCRs ............................................................... 38
Picture Search Options ........................................................................................................ 39
Forward and Reverse Search ........................................................................................ 39
Slow Motion .................................................................................................................. 39
Frame Advance ............................................................................................................. 39
Index Search .................................................................................................................. 40
Go-To Search ................................................................................................................. 40
Commercial Advance .......................................................................................................... 41
Movie Advance .................................................................................................................... 43
Pro-Tect Plus™ Locking Feature ......................................................................................... 44
Tracking................................................................................................................................ 44
Time Counter ....................................................................................................................... 44
On-Screen Displays ..............................................................................................................45
Audio Set-Up Features ........................................................................................................ 46
Tape Playback ...................................................................................................................... 46
Other Information
.............................................................................................................. 47
Troubleshooting Tips ........................................................................................................... 48
Questions and Answers About COMMERCIAL ADVANCE ................................................. 51
Front Panel .......................................................................................................................... 52
Display Panel ....................................................................................................................... 53
Back Panel ............................................................................................................................ 54
Specifications ....................................................................................................................... 55
Cleaning the VCR ................................................................................................................55
RCA VCR Limited Warranty................................................................................................. 56
Finding the TV’s Video Line Input ...................................................................................... 57
Advanced Connection ......................................................................................................... 58
TV + VCR + Satellite Receiver ....................................................................................... 58
Glossary ................................................................................................................................ 59
Index .................................................................................................................................... 60
15708270 (VR661HF)(E) 03 ToC 2/7/01, 4:55 PM4
5
Changing Entertainment. Again.
Connections & Setup
Chapter Overview:
•Things to Consider Before Connecting
•Choosing Your Connection
•Making Connections
•Navigating On-Screen Menus
•Completing the QuickSet™ Guide
•Basic Recording
Chapter 1
15708270 (VR661HF)(E) 04 Setup 2/7/01, 4:55 PM5
6Chapter 1
Connections & Setup
Things to Consider Before Connecting
Components
Protect Components From Power Surges
•Connect all components before plugging any power cords into the wall outlet.
•Always turn off the TV and other components before you connect or disconnect any cables.
Position Cables to Avoid Audio Hum or Interference
•Insert all cable plugs firmly into their jacks.
•Place any Audio/Video (A/V) cables to the side(s) of the TV’s back panel instead of straight
down the back after connecting components.
•Try not to coil any twin-lead cables and keep them away from all A/V cables as much as
possible.
•Make sure all antennas and cables are properly grounded. Refer to the Safety Tips sheet
packed with your unit for detailed information.
Protect Components From Overheating
•Never block ventilation slots in any component. Arrange the components so that air can
circulate freely.
•Do not stack components.
•Allow adequate ventilation when placing components in a stand.
•Place an amplifier or satellite receiver on the top shelf of a stand so heated air rising from it
will not flow around other components.
Cable Considerations
The RF coaxial cable supplied with your VCR carries both sound and picture information. This is
the cable used in all connection diagrams illustrated in this chapter.
If your TV has A/V input jacks, you should use A/V cables (not supplied) to connect the VCR to
the TV. A/V cables provide better picture and sound quality than an RF coaxial cable. If you
would like to hook up your VCR using A/V cables, refer to the Advanced Connection
information on page 58 in the Other Information chapter of the manual.
15708270 (VR661HF)(E) 04 Setup 2/7/01, 4:55 PM6
Chapter 1 7
Connections & Setup
Components Connection Go To
Title
TV + VCR page 8
TV + VCR +
Satellite Receiver page 9
TV + VCR +
Cable Box page 10
VCR
TV
Satellite
Cable Box
VCR
TV
VCR
TV
RF Coaxial Cable
Using the RF Coaxial Cable to Connect the
VCR to a TV
This graphic shows the RF coaxial cable supplied with your VCR. This will be
the cable used for the basic connections represented in this chapter.
Notes: To hear stereo sound, you will need to purchase Audio/Video (A/V)
cables (not provided) and connect the VCR to the TV. A/V jacks and cables
also provide a superior image and sound quality. For details about using
this advanced setup, see the instructions on page 58.
Using A/V jacks to connect the VCR to the TV requires tuning to the TV’s
Video Line Input to see the VCR’s picture. For more information about
finding your TV’s Video Line Input, see page 57.
If you prefer, we can provide you with the name of an Authorized Service
Representative who will visit your home for a fee to install your electronic
entertainment system and to instruct you in its operation. For details about
this service, call 1-888-206-3359.
Choose Your Connection
There are several ways to hook up your VCR depending on the components connected. Please use
the following chart to determine which connection is best for you and proceed to the appropriate
page.
15708270 (VR661HF)(E) 04 Setup 2/7/01, 4:55 PM7
8Chapter 1
Connections & Setup
TV + VCR
Note: Your television back panel may not look exactly like the model
shown here.
1. Connect the VCR to the TV
Connect one end of the supplied RF coaxial cable to the RF OUT jack on
the back of the VCR and the other end to the TV’s Antenna IN jack.
2. Connect the antenna/cable feed to the VCR
Connect the cable or antenna RF coaxial cable to the ANT. IN jack on your
VCR.
Note: Flip the CH 3/4 switch on the back of the VCR to the channel that is
not used in your area. This will be the channel that the TV must be tuned
to in order to see the VCR’s picture.
Go To Page 11
Need Some Help?
If you prefer, we can
provide you with the
name of an Authorized
Service Representative
who will visit your home
for a fee to install your
electronic entertainment
system and to instruct you
in its operation. For
details about this service,
call 1-888-206-3359.
VCR
TV
VCR
TV (back panel)
CABLE/
ANTENNA
VIDEO RL / MONO
S-VIDEO
AUDIO
L
IN
OUT
From Cable
or Antenna
ANT. IN
RF OUT
CH.
VIDEO
AUDIO
OUT IN
R
L
3 4
2
1
15708270 (VR661HF)(E) 04 Setup 2/7/01, 4:55 PM8
Chapter 1 9
Connections & Setup
TV + VCR + Satellite Receiver
Note: Your television and/or satellite receiver back panels may not look
exactly like the models shown here.
1. Connect the VCR to the TV
Connect one end of the supplied RF coaxial cable to the RF OUT jack on
the back of the VCR and the other end to the TV’s Antenna input jack.
2. Connect satellite receiver to the VCR
Connect a second RF coaxial cable (not included) to the antenna output
jack on the satellite receiver and to the ANT. IN jack on the VCR.
3. Connect the antenna to your satellite receiver
If necessary, connect an antenna or cable box RF coaxial cable (not
included) to the antenna input jack on the satellite receiver.
4. Connect the satellite feed to the satellite receiver
Connect the satellite receiver’s RF coaxial cable feed (not included) to the
satellite input jack on the satellite receiver.
Go To Page 11
Need Some Help?
If you prefer, we can
provide you with the
name of an Authorized
Service Representative
who will visit your home
for a fee to install your
electronic entertainment
system and to instruct you
in its operation. For
details about this service,
call 1-888-206-3359.
VCR
TV
Satellite
CABLE/
ANTENNA
VCR
TV
VIDEO RL / MONO
S-VIDEO
AUDIO
L
IN
OUT
CH3
CH4
S-VIDEO
L
R
VIDEO
OUT
IN FROM ANT
OUT TO TV SATELLITE
IN
From
Satellite
From Cable
or TV Antenna
ANT. IN
RF OUT
CH.
VIDEO
AUDIO
OUT IN
R
L
3 4
SATELLITE
RECEIVER
1
2
4
3
15708270 (VR661HF)(E) 04 Setup 2/7/01, 4:55 PM9
10 Chapter 1
Connections & Setup
TV + VCR + Cable Box
Note: Your television and/or cable box back panels may not look exactly
like the models shown here.
1. Connect the VCR to the TV
Connect one end of the supplied RF coaxial cable to the RF OUT jack on
the back of the VCR and the other end to the TV’s Antenna input jack.
2. Connect the cable box to the VCR
Connect one end of a second RF coaxial cable (not included) to the cable
box’s antenna output jack and the other end to the ANT. IN jack on the VCR.
3. Connect the cable feed to your cable box
Connect the RF coaxial cable feed (not included) to the antenna input jack
on the cable box.
Go To Page 11
Need Some Help?
If you prefer, we can
provide you with the
name of an Authorized
Service Representative
who will visit your home
for a fee to install your
electronic entertainment
system and to instruct you
in its operation. For
details about this service,
call 1-888-206-3359.
VCR
TV
Cable Box
CABLE/
ANTENNA
VCR
TV
VIDEO RL / MONO
S-VIDEO
AUDIO
L
IN
OUT
CH3
CH4
CABLE BOX
S-VIDEO
IN FROM ANT
OUT TO TV
From Cable
Feed
ANT. IN
RF OUT
CH.
VIDEO
AUDIO
OUT IN
R
L
3 4
1
2
3
15708270 (VR661HF)(E) 04 Setup 2/7/01, 4:55 PM10
Chapter 1 11
Connections & Setup
Set the VCR’s CH 3/4 Switch
The CH 3/4 switch on back of the VCR determines what channel the TV must be tuned to see
the VCR’s image. Choose whichever channel is not used locally in your area.
Note: If you connected components using A/V jacks and cables, the VCR’s signal must be
viewed using the TV’s Video Line Input. To find the Video Line Input, refer to the manual
that came with the TV or see How to Find Your TV’s Video Line Input on page 57 in the
Other Information section of this manual.
Plug in the VCR
Your VCR’s power cord has a plastic band strung through the blades. Remove the plastic band
before plugging the cord into the power outlet. To remove the band, cut with a pair of
scissors and pull it free of the blades. Once the plastic is removed, match the wide blade of the
power cord to the wide slot in the AC outlet. Be sure to insert the plug completely.
Put Batteries in the Remote Control
1. Remove the battery compartment cover on the remote control.
2. Insert new batteries matching the polarities (+ and –) on the batteries with
the diagram in the battery compartment.
3. Put the battery compartment cover back on the remote.
Turn on the TV and VCR
Turn on the TV and press the VCR button on the remote control to turn it on.
Note: If you have an RCA, GE, or Proscan TV, your VCR’s remote control
may be able to operate it without being programmed. Press the TV button
on the remote control and then the ON•OFF button. If neither one turns on
the TV, see Using the Remote Control starting on page 25 for details about
programming the remote control to operate other brands of TVs.
Tune the TV
Tune the TV to the VCR viewing channel. The VCR viewing channel is channel
3, 4, or the TV’s video line input.
•If you connect your VCR using RF coaxial cable only, turn the TV to
channel 3 or 4 (whichever was set on the CH 3/4 switch).
•If you connected the VCR using A/V jacks and cables, select the TV’s video
line input. For more information see How to Find the TV’s Video Line Input
on page 57 in the Other Information section of this manual.
15708270 (VR661HF)(E) 04 Setup 2/7/01, 4:55 PM11
12 Chapter 1
Connections & Setup
Using the Remote Control to
Navigate On-Screen Menus
The technical term is “Navigation” – how you move through the on-screen menus. The theory is
the same for all the menu screens; use the corresponding number button on the remote control
select it.
To choose an on-screen item, press the remote control’s corresponding number button.
Note: Selecting a menu item can take you to another menu, activate a choice, or activate a
data entry field (such as the hour field in the Set Time menu).
Select a language.
Seleccione un idioma.
Choisissez une langue.
1 English
2 Español
3 Français
Complete the QuickSet Guide
The menu system in your VCR allows you to customize your preferences as
well as use all the VCR’s features. To help you use the VCR as quickly as
possible, there is an initial QuickSet Guide that walks you through several
important setup steps at one time.
The first time you turn on the VCR, you will be able to set up available
channels, time and date information, and more. The first menu you will see
asks which language you prefer to have the on-screen menus appear in.
Note: With numbered menu choices, press the corresponding number
button on the remote control to automatically select it. In the case of the
language menu, press 1 for English, 2 for Español (Spanish), or 3 for
Français (French).
The remaining menus throughout the setup will appear in the language chosen.
Just follow the step-by-step procedures until the QuickSet Guide is complete.
Accessing Menus
The series of preferences that are set in the QuickSet Guide can also be
handled individually using the VCR’s on-screen menu system. There are other
settings not covered in the initial setup that are also handled using the on-
screen menus.
For example, if you decide to run the QuickSet Guide again, you can access the
Setup menu by pressing the remote control’s MENU button. Once the Main
Menu is displayed, press the 5 button to choose Setup. From there, you can start
the QuickSet Guide from the beginning.
All on-screen menus are accessed the same way, starting in the Main Menu
which is displayed by pressing the remote control’s MENU button.
Note: See chapter two, Using On-Screen Menus, for details about changing
the VCR’s individual settings.
VCR MAIN MENU
1 VCR Plus+
2 Timer Recordings
3 Time
4 Channels
5 Setup
6 Preferences
7 Audio
8 Language
0 Exit
All of the VCR’s menus are
accessed through the Main
Menu. Press the remote
control’s MENU button to
start.
15708270 (VR661HF)(E) 04 Setup 2/7/01, 4:55 PM12
Chapter 1 13
Connections & Setup
VCR Basics
Once your initial settings are complete, you can begin using your VCR. In order to begin, you
must first understand some basic concepts.
.
Safety Tab
Automatic Tracking
The VCR has automatic tracking
which adjusts the picture when
playing back a tape recorded on
another VCR. To adjust tracking
manually, use the TRACKING -/+
buttons on the remote control.
Playing a Tape
1. Tune the TV to your VCR viewing channel (03, 04, or the video line input).
2. Insert a tape in the VCR.
If the Auto Play feature is set to ON, the tape automatically begins playback
(if the safety tab on the tape is removed).
•Press FWD or REV (FORWARD or REVERSE on the remote control) to
cue the tape at the desired starting position.
•Press PLAY (if necessary) to begin tape play.
•Press PAUSE for stop action.
•Press TRACKING up or down (TRACKING + or – on the remote
control) to remove any streaks from the picture, if necessary.
•Press STOP to stop playback.
Automatic Rewind
The VCR automatically rewinds the tape if it reaches the end of the tape during
playback. While rewinding, you can press the ON•OFF button and the VCR will
turn off after finishing. If the tape has no safety tab, it will be ejected.
Tape Eject
Press the EJECT button on the VCR when stopped to eject the tape. You can
also press and hold the remote control’s STOP button for three seconds.
Recording
To Capture Programming with Basic Recording Methods:
1. Set the tape speed by pressing the SPEED button on the remote control
(see Recording Speed on page 23 for information about recording speeds).
2. Press the RECORD button to begin recording.
3. Press the STOP button to halt recording.
If you just want to pause the recording for a short time (like during a
commercial), press PAUSE instead of STOP.
Check the Safety Tab
No matter which recording option you use, make sure there is a tape in the
VCR with its safety tab in place. You cannot record on a tape with its safety tab
removed. If the safety tab is removed and you want to record, simply cover the
hole with adhesive tape.
15708270 (VR661HF)(E) 04 Setup 2/7/01, 4:55 PM13
This page left blank intentionally
15708270 (VR661HF)(E) 04 Setup 2/7/01, 4:55 PM14
15
Changing Entertainment. Again.
Using the VCR’s
Menu System
Chapter Overview:
•Using On-Screen Menus
•Cable Box Setup
•Setting Time and Date
•Setting VCR Preferences
Chapter 2
15708270 (VR661HF)(E) 05 Menu 2/7/01, 4:55 PM15
16 Chapter 2
Using On-Screen Menus
Using On-Screen Menus to Set Up Features
You set up many of the VCR’s features by using the menu system as discussed in the previous
chapter. Each feature that appears in the QuickSet Guide is explained in this section as well as a
few other features you should set up to get the most out of your VCR.
Note: Not all the VCR screens are shown in this manual when explaining how to access
features.
Language
Selecting your preferred language determines how the on-screen displays will
appear. To change the language:
1. Press MENU to display the VCR MAIN MENU.
2. Press the 8 button to select LANGUAGE.
3. Select English, Spanish (Español), or French (Français).
Cable Box Setup
This setup applies only when all channels are received through a cable box. In
this case, the VCR will automatically enter the channel used to view cable box
programming. Your VCR will use this channel for all future timer recordings.
1. Press MENU to display the VCR MAIN MENU.
2. Press 4 to display the CHANNELS menu.
3. Press 5 to display the CABLE BOX SETUP menu.
LANGUAGE
Select a language.
1 English
2 Español
3 Français
Press MENU to continue
CHANNELS
1 Auto Channel Search
2 Add/Remove Channels
3 Signal Type: CABLE
4 VCR Plus+ Setup
5 Cable Box Setup
6 SAT Setup
0 Exit
Is Something Missing?
These instructions will not
show all of the step-by-step
On-Screen Menus. Make
sure to follow the
instructions completely to
get to the menus being
discussed.
15708270 (VR661HF)(E) 05 Menu 2/7/01, 4:56 PM16
Chapter 2 17
Using On-Screen Menus
4. Select one of the three choices. If “ALL Channels” is selected, enter the
output channel of the cable box (usually 03 or 04), or if A/V jacks connect
the VCR to the TV, press the INPUT button on the VCR’s remote control.
5. Once you complete the setup, the VCR confirms that it will now receive all
signals on the designated channel.
VCR Channels List
Your VCR may come with a list of channels preset at the factory. Even though it
may come with such a list, you might want to add or delete certain channels.
Note: If you use a cable box to view all channels, this step is not necessary.
Auto Channel Searching
Notes: Use Auto Channel Search to place all available channels in memory.
If you ever change cable or antenna signals, you may need to run the Auto
Channel Search feature again.
1. Press the MENU button to display the VCR MAIN MENU.
2. Press 4 to select CHANNELS.
3. Press 1 to select AUTO CHANNEL SEARCH.
4. Select one of the three options:
Cable TV searches for cable stations.
Antenna searches for local broadcast stations.
Detect Automatically decides which input to use for you.
Note: With Detect Automatically, a strong cable or antenna signal in your
area may cause channels to be detected inaccurately. If this should happen,
manually select the input signal for the system you have.
The VCR begins scanning for channels available in the area (taking about
one-to-two minutes). When scanning is complete, the VCR tunes to the
lowest channel available. After completing Auto Channel Search, pressing
the remote control’s CHAN + or - buttons should only select active
channels.
CABLE BOX SETUP
Do you use your cable
box to receive ALL
channels or only SOME
channels?
1 ALL channels
2 Only SOME channels
3 Cancel setup
CABLE BOX SETUP
The VCR will now
receive all signals
from the cable box
on channel 04.
Press MENU to continue
AUTO CHANNEL SEARCH
What type of signal
are you using?
1 Cable TV
2 Antenna
3>Detect Automatically
0 Cancel
15708270 (VR661HF)(E) 05 Menu 2/7/01, 4:56 PM17
18 Chapter 2
Using On-Screen Menus
Changing the Signal Type
This feature is useful if your cable signal goes out; it allows you to switch to a
regular antenna for alternate television reception.
1. Press the MENU button to display the VCR MAIN MENU.
2. Press the 4 button to choose CHANNELS.
3. Press 3 to choose between Signal Type: Cable and Antenna. When
finished, press 0 to exit back to the Main Menu and 0 again to exit to
normal viewing.
Adding or Removing Channels
You might want to add or remove channels after using Auto Channel Search,
especially if there are weak signals or channels with content you don’t care for.
1. Press the MENU button to display the VCR MAIN MENU.
2. Press 4 to choose CHANNELS.
3. Press 2 to choose ADD/REMOVE CHANNELS. To go to the channel you
want to add or remove, use the remote control’s CHANNEL + or – buttons
or enter a specific channel number using the number buttons.
Once the desired channel is displayed, the on-screen menu will tell you if
the channel is currently in the VCR’s viewing list. Press the CLEAR button to
remove a channel from the available channels list or press the INFO button
to add it.
4. Press the MENU button to exit out of the menus.
Note: To view active channels, use the remote control’s CHANNEL + and -
buttons. You can also access channels not available in the active channel
list by using the remote control’s number buttons to enter the specific
channel number.
CHANNELS
1 Auto Channel Search
2 Add/Remove Channels
3 Signal Type: CABLE
4 VCR Plus+ Setup
5 Cable Box Setup
6 SAT Setup
0 Exit
ADD/REMOVE CHANNELS
Channel 115
is presently ADDED
Press CLEAR to remove
Press MENU to exit
15708270 (VR661HF)(E) 05 Menu 2/7/01, 4:56 PM18
Chapter 2 19
Using On-Screen Menus
Time and Date
Your VCR gives you two ways to set the time and date; manually or by using the Auto Clock Set
feature. Using Auto Clock Set enables the time to be updated each time the VCR is turned off by
using time and date information carried in certain broadcast signals.
Auto Clock Set Feature
The Auto Clock Set feature is set to ON by default at the factory. In the ON setting, the VCR
looks for a channel carrying time data and updates the clock automatically. In order for Auto
Clock Set to work properly though, certain steps must first be completed such as Auto Channel
Search, setting the time zone, and setting the Daylight-Saving feature.
Notes: Auto Clock Set is available only in limited areas.
You must set available channels, time zone, and Daylight-Saving settings for Auto Clock Set
to work.
When using Auto Clock Set with a cable box, the VCR will not reset the clock after a power
outage unless the cable box is tuned to the channel carrying time data.
If the time does not automatically set after trying for ten minutes, manually set the time
and date information using the TIME menu (see the next page for information on manually
setting time and date information).
To Turn Auto Clock Set ON
Note: make sure that available channels, time zone, and Daylight-Saving
features are set before turning on Auto Clock Set.
1. Press MENU to display the VCR MAIN MENU.
2. Press 3 to choose TIME.
3. Press the 2 button repeatedly to toggle between Auto Clock Set ON and OFF.
Setting the Time Zone
1. Press MENU to display the VCR MAIN MENU.
2. Press 3 to choose TIME.
3. Press 3 to chose SET TIME ZONE.
4. Select your time zone by pressing the corresponding number button.
If you select Automatic for your time zone, the VCR sets the clock using the
first time information it finds. If the time set is not correct, select another
time zone or set the time and date through the menu system.
TIME
1 Set Time and Date
2 Auto Clock Set: ON
3 Set Time Zone
4 Set Daylight Saving
Time Data was found
on channel 20.
0 Exit
SET TIME ZONE
What is your Time Zone?
1 Eastern
2 Central
3 Mountain
4 Pacific
5 Alaska
6 Hawaii
7>Automatic
Press MENU to continue
15708270 (VR661HF)(E) 05 Menu 2/7/01, 4:56 PM19
20 Chapter 2
Using On-Screen Menus
Setting Daylight-Saving Time
1. Press MENU to display the VCR MAIN MENU.
2. Press 3 to choose TIME.
3. Press 4 to choose SET DAYLIGHT SAVING.
4. Select the appropriate option.
Notes: DST stands for Daylight–Saving Time.
If you choose Automatic for the time zone, the VCR sets the clock using any
DST information broadcast in the channel’s signal.
Setting Time and Date Manually
If Auto Clock Set was unsuccessful, set the time and date manually in the TIME
menu. Auto Clock Set is automatically turned off when time and date
information is set this way.
1. Press MENU to display the VCR MAIN MENU.
2. Press 3 to choose TIME.
3. Press 1 to choose SET TIME AND DATE.
4. Enter the data using the number buttons. Press 0 before single-digit
numbers and follow the on-screen directions to exit the menus.
SET TIME AND DATE
Time --:--
(hh:mm)
Date --/--/--
Press MENU to cancel
SET DAYLIGHT SAVING
Does your area observe
Daylight Saving Time
from April to October?
1 Yes, DST is observed
2 No
3 Automatic
Press MENU to continue
Displaying Time and Date
Pressing the INFO button on
the remote control or VCR
displays the time and date on
screen temporarily.
TIME
1 Set Time and Date
2 Auto Clock Set: ON
3 Set Time Zone
4 Set Daylight Saving
Time Data was found
on channel 20.
0 Exit
TIME
1 Set Time and Date
2 Auto Clock Set: ON
3 Set Time Zone
4 Set Daylight Saving
Time Data was found
on channel 20.
0 Exit
15708270 (VR661HF)(E) 05 Menu 2/7/01, 4:56 PM20
Chapter 2 21
Using On-Screen Menus
Additional Set Up Features in the
Preferences Menu
Note: The features described on the following pages are all accessed
through the PREFERENCES menu.
To Access the PREFERENCES menu:
1. Press MENU to display the VCR MAIN MENU.
2. Press 6 to select PREFERENCES.
You are now ready to select an item from the PREFERENCES menu to set up.
Remote VCR1/VCR2 Option
Some universal remote controls have buttons labeled VCR1 and VCR2. These
remotes can operate up to two VCRs. If you have a universal remote control with
this ability, your RCA VCR can be controlled with either the VCR1 or VCR2 button.
See the documentation that came with your universal remote control for details
about programming it to operate your RCA VCR.
In the PREFERENCES menu, press 1 to select the Remote Control feature. Then
press the VCR2 button on your universal remote control to change the setting.
Then, the VCR will respond to the universal remote control’s VCR2 button. To
change the remote control setting back to VCR1, display the PREFERENCES menu,
press 1, and then press the VCR1 button on the universal remote control.
Note: Remember you must press VCR1 or VCR2 on a universal remote
control (not included) —whichever is selected in the PREFERENCES menu—
before the remote control will operate the VCR.
Auto Play
With Auto Play turned ON (the factory default setting), the VCR automatically
starts playback when you insert a tape with its safety tab removed.
To Access Auto Play:
1. In the PREFERENCES menu, press 2 repeatedly to switch between Auto
Play: ON and OFF.
•Select ON if you want a tape with its safety tab removed to start playing
automatically when inserted.
•Select OFF if you do not want a tape with its safety tab removed to start
playing automatically.
PREFERENCES
1 Remote Control: VCR1
2 Auto Play: ON
3 Auto TV/VCR: ON
4 EnergySaver: 2:00
5 Front Panel: AUTO
6 Tape Speed: SLP
7 Set Auto Repeat
8 COMMERCIAL ADVANCE
0 Exit
The PREFERENCES menu
allows changes to be made
to a variety of different
VCR features.
15708270 (VR661HF)(E) 05 Menu 2/7/01, 4:56 PM21
22 Chapter 2
Using On-Screen Menus
Auto TV/VCR
To control whether the VCR’s TV/VCR setting changes automatically to VCR-
viewing mode when turned on, use the Auto TV/VCR setting.
To Access Auto TV/VCR:
In the PREFERENCES menu, press 3 repeatedly to toggle between Auto TV/VCR:
ON and OFF.
Note: Pressing the TV•VCR button on the remote control will switch
between VCR and TV-viewing modes. When in VCR-viewing mode, VCR is
displayed on the front panel. The VCR indicator turns off when in TV-
viewing mode.
•Select ON to switch VCR-viewing mode on automatically when the power is
turned on. The VCR must be connected to the TV using the supplied RF
coaxial cable.
•Select OFF to remain in the TV-viewing mode when the VCR is initially
turned on. Leaving Auto TV/VCR off is useful if you use A/V cables to
connect the VCR to the TV and you watch the VCR’s picture using the TV’s
Video Line Input. This way, the antenna/cable signal will not be interrupted
by the VCR.
EnergySaver
By default, the VCR automatically turns off after two hours of inactivity. This can
be changed in the PREFERENCES menu by pressing the 4 button repeatedly to
change the time delay or to disable the feature altogether.
•Select OFF and the VCR will stay on until you shut it off.
•Select 1:00, 2:00, or 3:00 and the VCR will turn off after one, two, or three
hours of inactivity.
Thirty seconds before automatically shutting off, the VCR displays an on-screen
message reading, The VCR will turn off in 30 seconds. Press any key to cancel.
Pressing any remote control or VCR front panel button will halt the countdown.
If you use the VCR’s tuner instead of your TV to view channels, you may want
to turn off this feature.
Front Panel Brightness (VCR Display)
You can change the brightness level of the VCR’s front panel display. In the
PREFERENCES menu, press the 5 button repeatedly to toggle between options:
•AUTO means the display brightens when the VCR is on and dims when the
VCR is off.
•BRIGHT keeps the display bright whether the VCR is on or off.
•DIM keeps the display at a low brightness level whether the VCR is on or
off.
PREFERENCES
1 Remote Control: VCR1
2 Auto Play: ON
3 Auto TV/VCR: ON
4 EnergySaver: 2:00
5 Front Panel: AUTO
6 Tape Speed: SLP
7 Set Auto Repeat
8 COMMERCIAL ADVANCE
0 Exit
The PREFERENCES menu
allows changes to be made
to a variety of different VCR
features.
15708270 (VR661HF)(E) 05 Menu 2/7/01, 4:56 PM22
Chapter 2 23
Using On-Screen Menus
Tape Speed
You can choose as the preferred recording tape speed either Standard Play (SP)
or Super Long Play (SLP). The speed selected appears in the VCR’s front display
panel and in timer and VCR Plus+ system recording menus.
To Select a Preferred Tape Speed:
•In the PREFERENCES menu, press the 6 button repeatedly to switch between
SP and SLP settings.
Note: For an explanation of recording speeds, see the note to the left.
To Override the Preferred Tape Speed:
•Press the SPEED button on the remote control.
•Set the tape speed in the timer or VCR Plus+ system recording menus.
When you turn off the VCR, the tape speed reverts to the one selected as the
default.
Set Auto Repeat
A tape can be set to play the same segment over and over in a repeating loop
with the Set Auto Repeat feature. Set Auto Repeat uses the VCR’s memory
counter to determine the duration of the loop.
In the PREFERENCES menu, press the 7 button to choose Set Auto Repeat. The
SET AUTO REPEAT menu will ask for an ending time for the loop to be
specified:
•The CLEAR button will erase all three numbers entered and move the cursor
back to the first position (hours).
•The Press CLEAR to turn off message will appear only after the first number
has been entered into the end time.
•Auto Repeat is set back to -:-- by resetting the dialog box, ejecting a tape,
powering off the VCR, power interruption, or by recording start.
When a duration time has been set:
•The VCR will automatically switch to rewind if the counter meets or goes
past the set Auto Repeat duration.
•The VCR will automatically switch to playback during rewind if the counter
equals or is less than 0:00.
•The Auto Repeat may be adjusted by setting the counter to 00:00. This can
be done by pressing the CLEAR button while the tape counter is on screen
or on the front panel display.
•The counter will not reset while rewinding in an Auto Repeat loop.
AUTO REPEAT
Set the length of time
you want the tape to
play in a repeating loop
Loop from 0:00 to
2:--
(h:mm)
Press CLEAR to turn off
Press MENU to exit
Recording Speeds
SP (Standard Play)
Gives the best quality recording,
but fewer programs can be
recorded on the tape.
SLP (Super Long Play)
Gives three times the recording
time of tapes recorded in SP
mode.
Recording Times
Cassette SP SLP
T-120 2 Hr 6 Hr
T-160 2 Hr/40 Min 8 Hr
15708270 (VR661HF)(E) 05 Menu 2/7/01, 4:56 PM23
This page left blank intentionally
15708270 (VR661HF)(E) 05 Menu 2/7/01, 4:56 PM24
25
Changing Entertainment. Again.
Using the
Remote Control
Chapter Overview:
•Buttons on the Remote Control
•Programming the Remote to Operate Other Components
•How To Use the Remote After You’ve Programmed It
Chapter 3
15708270 (VR661HF)(E) 06 Remote 2/7/01, 4:56 PM25
26 Chapter 3
Using the Remote Control
I
N
P
U
T
T
V
•
V
C
R
ON•OFF
PLAY FORWARD
RECORD STOP PAUSE
F.A DV
CLEAR MENU SPEED
TRACKING
1
4
7
2
5
8
3
6
9
0
C
H
A
N
V
O
L
V
O
L
C
H
A
N
INFO SEARCH
MUTE GO BACK
TV VCR
REVERSE
Remote Control Buttons
The backlit remote has a light button ( ) that glows in the dark. Press
this button to light the buttons on the remote. The remote buttons
remain lit when they are pressed within a few seconds of each other. If
a button is not pressed within approximately seven seconds, the light
turns off to conserve battery power.
The remote control is capable of controlling your VCR and many
brands of televisions. If you have an RCA, GE, or Proscan TV, you may
be able to control it without having to program the remote.
Component Buttons
ON•OFF Turns off VCR when remote is set to control the VCR. Also
turns some compatible components on and off.
TV Turns on a compatible RCA, GE, or PROSCAN TV and sets the
remote to control the TV. Also used with the ON•OFF button to turn
on a different brand of TV (if programmed) and sets the remote to
control the TV.
VCR Turns on a compatible RCA, GE, or PROSCAN VCR and sets the
remote to control the VCR.
VCR Function Buttons
CHAN Up or Down
Selects next higher or lower channel in the VCR’s
channel memory.
CLEAR Resets time counter to 0:00:00. Allows you to change entries
when setting the clock or a timer recording.
F. ADV Lets you view one frame with each press of the button when
tape is in pause.
FORWARD Fast forwards the tape when the VCR is stopped. Searches
forward through a tape during playback. Starts slow motion during
play-pause and increases slow-motion speed.
GO BACK Switches between two channels. Select one channel and
then select another using the number buttons. Press GO BACK to
switch between the two channels. In menu mode, press to go back to a
previous menu.
INFO Shows the status displays on the TV screen.
INPUT Selects between the VCR’s line input or tuner. Line input refers
to the signal coming from the component connected to the AUDIO/
VIDEO IN jacks on the back (L1) or front (L2) of the VCR.
MENU Brings up VCR MAIN MENU on the TV screen.
Numbers (0 through 9) Select a channel up to 99 by pressing two
numbers. Select a cable channel over 99 by pressing and holding 1
until 1 – – appears on the screen. Then press the other two numbers.
15708270 (VR661HF)(E) 06 Remote 2/7/01, 4:56 PM26
Chapter 3 27
Using the Remote Control
PAUSE Pauses playback or recording. Press PAUSE a second time to return to
playback or recording.
PLAY Plays a tape.
RECORD Starts VCR recording. Also used for Express recording.
REVERSE Rewinds the tape when the VCR is stopped. Searches backward through a
tape during playback. Starts slow motion during play-pause and decreases slow-
motion speed.
SEARCH Displays INDEX and GO-TO Search menus on screen when the VCR is
stopped. Advances the tape forward through 30 seconds of recorded material during
playback. Each press advances the tape an additional 30 seconds (up to five minutes).
This button also displays the MOVIE ADVANCE screen for prerecorded movies and
starts COMMERCIAL ADVANCE skipping during playback.
SPEED Selects a recording speed (SP or SLP).
STOP Stops the current VCR function such as record, playback, rewind, or fast
forward.
TRACKING Up or Down Lets you manually reduce the streaks that may appear on
the picture during play, slow motion, or pause. Reduces picture “jitter” during stop-
action playback.
TV•VCR Switches the picture signal so that it either comes from the VCR or cable/
antenna system.
TV Function Buttons
CHAN Up or Down
Selects next higher or lower channel in the TV’s channel
memory.
CLEAR Removes menus or status displays from the screen.
GO BACK Switches between two channels. Select one channel and then select
another using the number buttons. Press GO BACK to switch between the two
channels.
INFO Shows the TV’s status displays on the TV screen.
INPUT Selects between the TV’s input channel or tuner. Press to see the VCR signal if
you connected your VCR using the
AUDIO/VIDEO jacks.
MUTE Reduces volume to minimum level.
Numbers (0 through 9) Select a channel up to 99 by pressing two numbers. Select
a cable channel over 99 by pressing and holding 1 until 1 – – appears on the screen.
Then press the other two numbers.
ON•OFF Turns a compatible TV off and on.
VOL Up and Down Raises and lowers sound of TV.
15708270 (VR661HF)(E) 06 Remote 2/7/01, 4:56 PM27
28 Chapter 3
Using the Remote Control
Using the INPUT Button
Use the INPUT button to toggle through the available Video Line Input sources (L1, L2, and
regular broadcasting signals) and regular broadcast signals. Video Line Input allows you to view
the image from a connected device (like a camcorder) through the VCR.
1. Press the remote control’s VCR button to activate VCR-controlling mode. Make sure that the
VCR is turned ON.
2. Press the remote control’s INPUT button to tune to the Video Line Input source. L1
represents the rear A/V jacks and L2 represents the front A/V jacks.
3. Press the INPUT button again to tune back to the broadcast signal you were previously
watching through the VCR.
Operating a TV with the VCR’s Remote Control
The remote control that came with your VCR can be programmed to operate most brands of
remote-controllable TVs and should already control most RCA, GE, and Proscan models without
programming.
Do You Need to Program the Remote?
To determine whether the remote control needs to be programmed to operate your TV, turn the
TV on, point the remote control at it, then press the remote control’s TV button (this puts the
remote control into TV-operating mode and should automatically turn on most RCA, GE, and
Proscan TVs). Press the remote control’s ON•OFF button to see if the TV responds to the
command. If not, the remote control needs to be programmed to control that model TV.
Programming the Remote Control
To program your remote control, you must use the code list on the next page. Look up the
brand name of your TV and the code(s) that brand uses.
Notes: This remote control may not operate all models of the brands shown in the code list.
Note the difference between the TV and VCR on-screen displays to know which component
the remote control is operating.
1. Turn on the TV.
2. Find your TV brand and code number(s) in the code list.
3. Press and hold the TV button on the remote control.
4. Enter the code from the code list.
5. Release the TV button, then press the CHAN up or down button. If the TV responds to the
remote control’s command, the remote is programmed.
6. If the TV does not respond, repeat these steps using the next code listed for your TV’s
brand.
15708270 (VR661HF)(E) 06 Remote 2/7/01, 4:56 PM28
Chapter 3 29
Using the Remote Control
TV Codes
Akai ......................................... 03
AOC ..................................... 06,12
Candle ....................................... 06
Citizen ....................................... 06
Colortyme ................................. 06
Concerto ................................... 06
Curtis Mathes ....................... 01,06
Daewoo ............................... 06,12
Daytron ..................................... 06
Electrohome ........................ 06,12
Emerson .................................... 06
Envision .............................. 05, 06
Fisher ..................................05, 08
GE .......................... 00, 01, 06, 11
Goldstar ............................... 06,12
Hallmark ................................... 06
Hitachi ................................. 06,14
Infinity ...................................... 04
J C Penney ....... 00, 01, 06, 09, 12
JBL ............................................. 04
Jensen ....................................... 06
JVC ...................................... 10, 11
Kawasho ............................. 03, 06
Kenwood ............................ 06, 12
Loewe ....................................... 04
Luxman ..................................... 06
LXI.................................04, 05, 07
Magnavox .....................04, 06, 12
Marantz ............................... 04, 06
MGA .................................... 06, 12
Mitsubishi ........................... 06, 12
MTC .......................................... 06
NAD ........................................... 07
NEC ............................................ 06
Panasonic ...................... 04, 08, 11
Philco ............................. 04, 06, 12
Philips ...................... 03, 04, 06, 12
Pioneer ...................................... 06
Portland ............................... 06, 12
Proscan ...................................... 01
Proton ........................................ 06
Quasar ....................................... 11
Radio Shack ................... 01, 05, 13
RCA ................................ 01, 06, 12
Realistic ...................................... 05
Sampo ........................................ 06
Samsung ........................ 06, 09, 12
Sanyo ................................... 05, 08
Sears ....... 01, 05, 06, 07, 08, 10, 12
Sharp ..................................... 06,13
Sony ........................................... 03
Soundesign ................................ 06
Sylvania.......................... 04, 06, 12
Technics ..................................... 11
Techwood .................................. 06
Teknika ...................................... 06
TMK ........................................... 06
Toshiba .................... 05, 07, 08, 09
Universal .................................... 00
Victor ......................................... 10
Wards ........... 00, 01, 04, 06, 12, 13
Yamaha ...................................... 12
Zenith ........................................ 02
15708270 (VR661HF)(E) 06 Remote 2/7/01, 4:56 PM29
30 Chapter 3
Using the Remote Control
Operating the TV
After you set up the remote control, see which buttons operate your TV:
1. Point the remote control at the TV, and press the TV button. If the TV does not turn on,
press the TV button and then press the ON •OFF button.
2. You may want to experiment to see which buttons operate your TV. Try pressing buttons,
such as VOL and MUTE. See the button descriptions in this chapter for details about what
each remote control button does.
15708270 (VR661HF)(E) 06 Remote 2/7/01, 4:56 PM30
31
Changing Entertainment. Again.
Using the VCR’s Features
Chapter Overview:
•Recording
•Express Recording (XPR)
•Timer Recordings
•Using the VCR Plus+ System
•Copying and Editing Tapes
Chapter 4
15708270 (VR661HF)(E) 07 Ftrs 2/7/01, 4:56 PM31
VCR Features
32 Chapter 4
Recording Features
Your VCR provides many ways to capture programming:
1. Recording lets you press one button to record a program.
2. Express Recording (XPR) allows recording to start while a program is being watched.
This feature automatically stops recording after a designated period of time.
3. Timer Recording program the VCR for a daily, weekly, or one-time recording which will
automatically start and stop at the times you set.
4. Timer Recording with the VCR Plus+ System program the VCR by entering a PlusCode
programming number found in most TV program listings.
Express Recording (XPR)
Use XPR to quickly record the remaining portion of a program being watched. XPR is a great
way to capture the end of a sporting event that has run into overtime or a live broadcast that
runs long.
XPR works in 30-minute increments. You can capture the last 30, 60, 90, etc. minutes of
programming (depending on tape length), up to four hours total.
To Activate XPR:
1. If necessary, turn on the VCR and tune it to the channel with the desired
programming.
2. If necessary, insert a tape with its safety tab in place into the VCR. Make
sure it is cued to record at the proper starting point.
Note: To override the preferred tape speed setting, press the SPEED button
on the remote control repeatedly to toggle between SP and SLP choices.
3. Press the RECORD button on the remote control or VCR front panel to start
recording.
4. Repeatedly press the RECORD button to set up the recording duration.
•Each press of the RECORD button adds 30 minutes of recording time.
•The VCR automatically turns off after recording for the set time.
•To stop an XPR recording, press and hold the STOP button on the
remote control or VCR front panel for several seconds until STOP
appears on the VCR on-screen display.
Rec Ch 36
Record Length 0:00
Press REC to set length
Rec Ch 36
Record Length 1:30
Press REC to set length
15708270 (VR661HF)(E) 07 Ftrs 2/7/01, 4:56 PM32
VCR Features
Chapter 4 33
Timer Recording
You can program up to eight different broadcasts to be recorded.
Notes– In order for a timer recording to work:
•The VCR’s clock must be set correctly.
•Insert a tape with its safety tab in place and enough tape to record
the program.
•If you’ve set up the VCR for a cable box for all channels, the output of
your cable box appears in the channel item of the Timer Recording
menu.
•PROGRAMS OVERLAP appears if two programs whose times overlap
are entered.
•TIMER appears in the display when you turn off the VCR and a timer
recording has been set. TIMER flashes if there is no tape in the VCR
when a timer recording has been set and the unit is turned off.
•For a cable box or satellite receiver, turn it on and tune it to the
channel you want to record before the recording is to begin.
To Set Up to as Many as Eight Timer Recording Programs:
1. Press the MENU button to display the VCR MAIN MENU.
2. Press the 2 button to choose TIMER RECORDINGS.
3. Press the 1 button to choose Create a New Program.
4. Select how often you want the program to record.
5. Enter the data for the program with the number buttons.
The data includes the channel number (press INPUT to select the Video Line
Input if using A/V jacks to connect the VCR to the TV), and start and end
times (including AM or PM). The start date is automatically entered based on
the VCR clock. Both the recording date and speed can be changed.
6. Review the information to make sure it is correct.
7. Press the MENU button to save.
Stopping a Timer Recording
To stop or cancel a timer recording in progress (even an Express Recording):
Press and hold the STOP button for several seconds until STOP appears in the
on-screen display.
Reviewing and Clearing Programs
To review programs that you have already set up:
1. Press the MENU button to display the VCR Main Menu.
2. Press the 2 button to choose TIMER RECORDINGS.
3. Press the 2 button to choose Review Existing Progs.
4. Press CLEAR to erase or MENU to see the next saved timer recording
program.
Program 1 (One time)
Channel 104 Cable
Start Time 12:00 AM
End Time 01:30 AM
Start Date 11/16/01 Fri
Tape Speed SLP
Press CLEAR to erase
Press MENU for next prog
TIMER RECORDINGS
1 Create a New Program
2 Review Existing Progs.
3 Use VCR Plus+ Code
0 Exit
How often should this
program record?
1 One time
2 Daily (every day)
3 Weekdays (M-F)
4 Weekly (once per week)
0 Cancel
Program 1 has been saved
Remember to insert a
recordable tape and
turn the VCR off before
the program start time.
Press MENU to continue
15708270 (VR661HF)(E) 07 Ftrs 2/7/01, 4:56 PM33
VCR Features
34 Chapter 4
VCR Plus+ SILVER System
The VCR Plus+ SILVER system makes VCR set up easier by setting and updating the clock and
channel list for you automatically. During the first-time QuickSet Guide setup, the VCR prompts
you to enter your zip code. Soon after, the VCR clock will set itself and your VCR Plus+ system
channel list will be input for you.
Time, date, and VCR Plus+ system information are downloaded from participating TV stations
over your antenna or cable system. Time and date information are updated each time the VCR is
turned off (and after every power interruption). So, when your TV stations or cable company
update their lineups, your VCR will get the most current channel list automatically, freeing you
from having to manually change the channel list yourself.
If your VCR Plus+ SILVER system fails to download the proper information for any reason, you
can always manually map the channels. You can also turn off AUTO VCR Plus+ if you keep
getting prompts about multiple cable services by pressing the 2 button in the VCR Plus+ SETUP
menu.
Turning ON or OFF the
Auto VCR Plus+ download
If the automatic VCR Plus+ download continuously fails for any reason, you will
see the prompt to the left.
If you decide to turn off Auto VCR Plus+ all together, you can do this by:
1. Press the MENU button on the remote control to access the VCR’s MAIN
MENU
2. Press 4 to access the CHANNELS menu.
3. Press 4 to access the VCR Plus+ Setup menu.
4. Pressing 1 will take you to a screen to manually map VCR Plus+ channels.
Pressing 2 will toggle between Auto VCR Plus+: ON or OFF.
Make sure this feature is turned off if you continually get fail to download
prompts and map the channels manually.
VCR Plus+ and PlusCode are registered trademarks of the Gemstar Development Corporation.
The VCR Plus+ system is manufactured under the license from Gemstar Development Corporation.
VCR PLUS+ SETUP
Last automatic setup
was unsuccessful.
Would you like to:
1 Try again
2 Finish setup manually
3 Cancel the auto setup
VCR PLUS+ SETUP
1 Set channel lists
2 Auto VCR Plus+: ON
VCR Plus+ data was not
found.
0 Exit
15708270 (VR661HF)(E) 07 Ftrs 2/7/01, 4:56 PM34
VCR Features
Chapter 4 35
Mapping VCR Plus+ Channels Manually
Using the VCR Plus+ SILVER system can make taping timer recordings for cable or off-air antenna
easier. If your VCR Plus+ SILVER system setup failed during the QuickSet, then you will need to map
the channels for your local service manually. A worksheet and abbreviated codes for typical cable
services in the U.S. and Canada are provided.
VCR PLUS+ SETUP
1 Set channel lists
2 Auto VCR Plus+: ON
VCR Plus+ data was not
found.
0 Exit
VCR+ Channel My Channel
5 --
4 --
3 -> -> -> --
2 --
1 --
Use CH+/- to select
Press 0-9 to change
Press MENU to save
VCR+ Channel My Channel
5 46
4 --
3 -> -> -> 23
2 --
1 --
Use CH+/- to select
Press 0-9 to change
Press MENU to save
(Screen shown is for an example only.)
1. Press the MENU button to display the VCR MAIN MENU.
2. Press the 4 button to choose CHANNELS.
3. Press the 4 button to choose VCR Plus+ Setup.
4. Press 1 to display the Set Channel Lists menu.
5. Enter the data following the on-screen directions using
your worksheet.
15708270 (VR661HF)(E) 07 Ftrs 2/7/01, 4:56 PM35
VCR Features
36 Chapter 4
Two-Digit VCR Plus+ System
Channel Numbers for
Cable TV (Canadian List)
67 .................. Allarcom Pay Television/
Superchannel
44 ........................ Arts & Entertainment
72 ........................ Cable News Network-
Headline News
61 ......................... Cable News Network
70 ............... Canadian Home Shopping
Network
56 ..................................... Canal Famille
69 ......................... Cathay International
Television Inc.
68 ................. Chinavision Canada Corp
60 ..................Country Music Television
63 ................................. Family Channel
62 ........................................ First Choice
96 ................................ First Choice Two
97 ............................ First Choice Three
99 ............................... First Choice Four
90 .......................... House of Commons
91 .......................... La Chaine Francaise
51 ..................... The Learning Channel
65 ............... MeteoMedia/The Weather
Network
48 ......................... MuchMusic Network
55 .......................................MusiquePlus
52 ............................. Nashville Network
73 ................................ Newsworld/CBC
53 .........................Le Reseau des Sports
43 .......................... The Sports Network
64 ....................................... Super Ecran
37 ....................................Super Ecran B
98 ................................... Super Ecran C
66 ............................... Telatino Network
46 .................................... TV5 Montreal
92 .............................. Viewer’s Choice 1
93 .............................. Viewer’s Choice 2
94 .............................. Viewer’s Choice 3
95 .............................. Viewer’s Choice 4
71 .......................... Vision TV: Canada’s
Faith Network
38 ...................... Youth TV, Canada Inc.
Note: Refer to your local TV program listings for a complete VCR Plus+ channel list for your
viewing area or contact your cable company. Using the list may save you some time.
Two-Digit VCR Plus+ System
Channel Numbers for
Cable TV (USA List)
35 ................... American Movie Classics
39 ........................ Arts &-Entertainment
57 ......................... Black Entertainment
54 .................................................. Bravo
42 ......................... Cable News Network
45 ............................................. Cinemax
98 .......................................... Cinemax 2
37 ..................... The Discovery Channel
53 ..........................The Disney Channel
63 ..................Entertainment Television
34 ........................ESPN Sports Network
47 .......................... The Family Channel
33 .............................. Home Box Office
95 ........................... Home Box Office 2
96 ........................... Home Box Office 3
51 ..................... The Learning Channel
46 ..............................................Lifetime
58 ...........................The Movie Channel
48 ................................ Music Television
49 ......................The Nashville Network
38 ...................................... Nickelodeon
64 ...........................Nostalgia Television
99 ........................... Quality Value Cable
41 ........................................... Showtime
97 ........................................ Showtime 2
59 .................................. Sports Channel
52 ............... Turner Network Television
44 ..................................... USA-Network
62 ....................................... Video Hits 1
93 .............................. Viewer’s Choice 1
94 .............................. Viewer’s Choice 2
55 .................................... WGN Chicago
43 .................................... WTBS Atlanta
60 .............................. WWOR-New York
15708270 (VR661HF)(E) 07 Ftrs 2/7/01, 4:56 PM36
VCR Features
Chapter 4 37
*Check your local or cable listings for the channel number you receive this station on.
**Check your local listings for broadcast or VCR Plus+ channel number assigned.
VCR Plus+ System Worksheet
Broadcast or
Cable-TV
Station Name
VCR Plus+ System
Channel Number**
Channel Number
You Receive the
Station On*
HBO 33
ESPN 34
15708270 (VR661HF)(E) 07 Ftrs 2/7/01, 4:56 PM37
VCR Features
38 Chapter 4
Recording Broadcast Stereo TV or SAP
(Second Audio Program)
Some TV programs are broadcast with stereo audio or SAP (Second Audio Program).
1. Turn on the TV and tune it to the VCR viewing channel (either 03, 04, or the TV’s Video
Line Input).
2. Insert a tape with its safety tab in place.
3. If your VCR viewing channel is 3 or 4, make sure the VCR indicator appears in the front
display. If not, press the TV•VCR button on the remote control to turn it on.
4. Press the SPEED button on the remote control if you want to override the preferred Tape
Speed setting. The tape speed indicator appears on the TV screen.
5. Select the channel or Video Line Input to be recorded.
6. Set the Reception: STEREO/MONO/SAP feature for the type of audio you want to record.
7. Press RECORD to start recording.
8. Press STOP when finished.
Caution:
The unauthorized recording of
satellite broadcasts, television
programs, or other copyrighted
materials may infringe the rights
of others.
CABLE BOX or ANTENNA
IN
OUT
TO TV
PLAYBACK
VCR
RECORDING
VCR
CH
ANT. IN
OUT IN
AUDIO
R
L
VIDEO
3 4
RF OUT
CH
3 4
OUT IN
AUDIO
R
L
VIDEO
ANT. IN
RF OUT
Copying and Editing Tapes Using Two VCRs
Use one VCR as the playback VCR and the other as the recording VCR.
1. Turn on the TV and VCRs.
2. Tune the TV to the VCR viewing channel (either 03, 04, or the TV’s Video
Line Input).
3. If you connected your VCR using the ANT. IN and RF OUT jacks, tune the
recording VCR to channel 3 or 4—whichever is selected on the back of the
playback VCR.
If you have connected your VCR using the A/V jacks, press INPUT on the
recording VCR’s remote control to select the Video Line Input. Select L1 for
the jacks on the back of the VCR or L2 for the jacks on the front.
4. Insert the tape you want to copy into the playback VCR. Insert a tape with
its safety tab in place into the recording VCR.
5. Press PLAY on the playback VCR to begin playback. When you reach the
point on the tape or program where you want to begin copying, press the
PAUSE button. You may need to adjust the tracking.
6. Press the RECORD button, then press PAUSE on the recording VCR.
7. Press the PAUSE buttons on both VCRs at the same time to begin copying
the tape.
8. To edit segments that you do not want to copy:
•Press PAUSE on recording VCR to pause copying.
•Locate the next segment you want to copy on the playback VCR by
using FWD, REV, and PLAY, and then press PAUSE.
•Press PAUSE on both VCRs at the same time to resume copying.
9. Press STOP on both VCRs when finished.
15708270 (VR661HF)(E) 07 Ftrs 2/7/01, 4:56 PM38
VCR Features
Chapter 4 39
Picture Search Options
The basic way to search during playback is using the remote control’s FORWARD or REVERSE
buttons (FWD and REV on the VCR). This section contains several other options available for
searching a tape.
Insert Tape:
Don’t forget to insert a recorded
tape when using the search
features.
Forward and Reverse Search
You can search a tape during playback either forward or reverse in direction.
Note: Sound is turned off during picture search.
1. Press the FORWARD button to search forward or the REVERSE button to
search backwards.
2. Press the FORWARD , REVERSE, or PLAY button to return to normal
playback.
Slow Motion
You can view a tape during play or play-pause mode using Slow Motion search.
1. In pause mode, press the FORWARD (FWD) or REVERSE (REV) button to
start slow-motion playback.
2. Press the FORWARD button to increase or the REVERSE button to decrease
the search speed.
3. Use the TRACKING + or – buttons to remove any streaks from the picture.
4. Press the PLAY button to return to normal playback.
The VCR switches automatically from slow-motion playback to stop after a
few uninterrupted minutes.
Frame Advance
Frame Advance lets you view single-frame action during playback.
1. While playback is in progress, press the remote control’s PAUSE button
(PLAY/PAUSE on the VCR) to freeze the action.
2. Press the F. ADV button on the remote control each time you want to view
the next frame of the recording.
3. Press the PAUSE or PLAY button on the remote control (PLAY/PAUSE on the
VCR) to return to normal playback.
15708270 (VR661HF)(E) 07 Ftrs 2/7/01, 4:56 PM39
VCR Features
40 Chapter 4
Index Search
The VCR has a “VHS Index Search System” that automatically records index marks on the tape
every time you start a recording. During playback you can locate the program you want to play
by the number of index marks or by scanning. The VCR will search forward or reverse from the
location you are at on the tape.
GO-TO SEARCH
Current tape counter is
2:17:25
Press REV or FWD
to go to -:--:00
Press SEARCH to exit
INDEX SEARCH
Press REV or FWD
to begin scanning
OR
enter a specific
index number
--
Press SEARCH to exit
To Activate Index Search:
1. While playing back, press the STOP button to freeze the action.
2. Press the SEARCH button on the remote control to display the INDEX
SEARCH screen on the TV screen.
3. If you want to search through a certain number of index marks, press two
number buttons to enter the number of marks you want to search. Press the
CLEAR button on the remote control to correct an entry.
4. Press the FORWARD button to search forward or the REVERSE button to
search in reverse. The VCR will locate your index mark and begin playback.
If you did not enter a specific index number, the VCR will locate the next
index mark and begin playback.
5. Press STOP to stop Index Search.
Notes– Certain index marks may be missed by the VCR including:
•Marks too close to the current location of the tape.
•Those at the beginning of a recording lasting five minutes or less.
•Index marks that start at the beginning of the tape.
Go-To Search
The Go-To Search feature enables the VCR to quickly locate a counter reading
anywhere on the tape. When the VCR locates the counter reading, it will begin
playback.
1. Press the STOP button.
2. Repeatedly press the SEARCH button on the remote control until the
GO-TO SEARCH menu appears on the screen.
3. Use the number buttons to enter the hour and/or minute of the counter
reading you want the VCR to go to. If necessary, press the CLEAR button on
the remote control to correct an entry.
4. Press the FORWARD button to search ahead or the REVERSE button to
search behind.
5. Press the STOP button to end a Go-To search.
15708270 (VR661HF)(E) 07 Ftrs 2/7/01, 4:56 PM40
VCR Features
Chapter 4 41
Commercial Advance
®
This feature uses patented technology to detect and mark most commercials on your tape for
any recording that is more than 15 minutes long. Once recording is finished, the VCR rewinds
the tape to the beginning of the recording and determines where the commercials are located. It
then marks the beginning and end of the detected commercial segments, and when finished,
returns the tape to the end of the recording. It does not erase commercials from the tape.
During playback, the VCR automatically skips the detected commercial segments, or you can
chose to manually skip them. This feature reduces three minutes of commercials to
approximately 8-12 seconds of fast forwarding in the SLP speed. You can select a background
display of blue or see the video as the commercials are skipped.
Because television signals do not indicate where commercials are located, this feature finds and
marks them through a set of formulas based on how television is broadcast today. Since
television stations broadcast differently and insert their own commercials, you may experience
some variations in this feature’s effectiveness. Station promotions, identifications, and
announcements are not considered commercials, but might be skipped. For more information,
see “Questions and Answers About COMMERCIAL ADVANCE ” in the Reference section.
All of the COMMERCIAL ADVANCE features are accessed through the
COMMERCIAL ADVANCE menu.
1. Press MENU to display the VCR MAIN MENU.
2. Press 6 to display the PREFERENCES menu.
3. Press 8 to display the COMMERCIAL ADVANCE menu.
Now you can select one of the COMMERCIAL ADVANCE features.
COMMERCIAL ADVANCE Marking
Press 1 to turn commercial Marking ON or OFF.
•Select ON, and the VCR will mark commercials within approximately 30
seconds for the following types of recording:
— Timer, Timer with VCR Plus+, or Express Recording Sets the
VCR to automatically mark commercials after the power is tuned
off.
— Recording Allows the VCR to prompt you to mark the
commercials when you’ve stop the recording.
•Select OFF and the VCR will not mark the commercials.
PREFERENCES
1 Remote Control: VCR1
2 Auto Play: ON
3 Auto TV/VCR: ON
4 EnergySaver: 2:00
5 Front Panel: AUTO
6 Tape Speed: SLP
7 Set Auto Repeat
8 COMMERCIAL ADVANCE
0 Exit
COMMERCIAL ADVANCE
1 Marking: ON
2 Playback: AUTO
3 Display: Blue
0 Exit
The VCR is waiting to
mark commercials in the
program you recorded.
1 Mark them now
2 Mark them later
3 Don't mark commercials
The VCR will begin
marking in 30 seconds...
15708270 (VR661HF)(E) 07 Ftrs 2/7/01, 4:56 PM41
VCR Features
42 Chapter 4
COMMERCIAL ADVANCE Playback
Press 2 to switch between Playback: AUTO and MANUAL.
•Select AUTO to have the VCR automatically advance through the blocks of
marked commercials.
It works with most 30, 45, and 60-second commercials.
A commercial group starting with the first two minutes or last two minutes
of a recording will not automatically be skipped.
A commercial will not be skipped if a recording starts in the middle of a
commercial segment, one isolated commercial is shown without others, or a
commercial is longer than one minute. Press FWD on the VCR (FORWARD
on remote) to scan through the commercial.
Part of a recorded program may be skipped if the program segment is
between commercials and less than one minute or there are frequent dark
and quiet scenes.
•Select MANUAL and the VCR won’t advance through the blocks of marked
commercials until you press SEARCH.
To Override Automatic Skipping
If part of the program you’ve recorded is passed over, you can temporarily
override the automatic skipping feature of COMMERCIAL ADVANCE.
1. While the desired portion of the program is being skipped, press the PLAY
or STOP button on the remote control or VCR front panel.
2. To view the portion of the tape that was skipped, rewind the tape back to a
position before the skipping started using the REVERSE (REV) button.
3. Press the PLAY button to start playback. The portion of the tape will no
longer be skipped.
Automatic skipping will be enabled again after the VCR detects the end of
the commercial group.
Notes: If you press SEARCH during playback of material other than
commercials, the VCR advances to the end of the next “marked”
commercial block and resumes playback.
The VCR resumes playback when it reaches the end of the marked
commercials.
COMMERCIAL ADVANCE Display
Press 3 to switch between Display: BLUE or VIDEO.
•Select BLUE to display a blue background when the VCR advances through
the block of marked commercials.
•Select VIDEO to display the recorded video when the VCR advances
through the block of marked commercials.
COMMERCIAL ADVANCE
1 Marking: ON
2 Playback: AUTO
3 Display: Blue
0 Exit
Timer Recordings and
COMMERCIAL ADVANCE
When using Timer Recordings
to tape two back-to-back
programs on the same
channel, you may want to
program each show
separately so that the
beginnings and ends of
programs are not
automatically skipped by
COMMERCIAL ADVANCE.
15708270 (VR661HF)(E) 07 Ftrs 2/7/01, 4:56 PM42
VCR Features
Chapter 4 43
MOVIE ADVANCE
What type of tape
is this?
1 Purchased/Rented Movie
2 Home Recording
3 Other
Press CLEAR to cancel
Movie Advance
®
MOVIE ADVANCE helps you locate certain parts of prerecorded movies (rented or purchased).
This feature works two ways: 1) you can go to the beginning of the movie, or, 2) you can skip
from one preview to the next. MOVIE ADVANCE works only on tapes with the safety tab
removed recorded in SP speed.
MOVIE ADVANCE
Would you like to go to
the start of the movie
or to the next preview?
1 Go to movie
2 Go to preview
Press CLEAR to cancel
Searching for preview
Press SEARCH to reverse
Press STOP to cancel
MOVIE ADVANCE
The movie is ready.
Press PLAY to start.
Press STOP to cancel
1. To select MOVIE ADVANCE, insert a tape with its safety tab removed and
press the SEARCH button on the remote control.
2. Press 1 if the tape is a purchased or rented movie, press 2 if it’s a
recording made at home, or press 3 if it’s something else, you don’t know,
or you do not want to select MOVIE ADVANCE.
Pressing 2 or 3 gives the same response and takes you to a different search
feature. If you accidentally make a wrong selection, press STOP•EJECT on
the VCR (STOP on remote) and reinsert the tape. Press SEARCH.
If you press 1, the MOVIE ADVANCE menu appears.
3. Press 1 to advance directly to the beginning of the movie or press 2 to view
the first (next) preview.
•Press 1 to Go To Movie. The following screen appears with a blue
background.
When the movie is found, you will see a message reading The movie is
ready. Press PLAY to start.
Note: You can press the STOP button to cancel the MOVIE ADVANCE
search.
•Press 2 to Go To Preview. The on-screen display will tell you that the
VCR is looking for the start of the next preview.
When a preview is detected, the VCR cues it and begins playing.
To Override the Show Previews Mode:
Press the SEARCH button while a tape is being searched.
Pressing the SEARCH button while:
•The tape is reversing will begin searching for the start of the next preview
or long commercial.
•The tape is searching forward for the next preview will reverse the tape
back to the start current preview.
•The VCR is playing will advance the tape to the start of the next preview,
long commercial, or the start of the movie (whichever comes first).
15708270 (VR661HF)(E) 07 Ftrs 2/7/01, 4:56 PM43
VCR Features
44 Chapter 4
0:30:00
Hours Minutes
Seconds
Pro-Tect Plus™ Locking Feature
To protect set timer recordings and to disable the VCR for use, the unit can be locked so that the
buttons on the front panel or remote control won’t work.
• To Lock: Press and hold either the remote control’s ON•OFF or VCR button until the front
panel display flashes.
•To Unlock: Press and hold either the remote control’s ON•OFF or VCR button until the
front panel display flashes for several seconds. Unlocking is the only way to turn on and use
the VCR.
Tracking
Your VCR has automatic tracking which removes streaks and noise from the picture. Automatic
tracking is activated when you insert a tape or turn on the VCR. Occasionally you may need to
manually adjust tracking, especially if the tape was recorded on a different VCR. Use the
TRACKING –/+ buttons on the VCR front panel or remote control to remove streaks and noise.
You can also use tracking when pausing a tape to reduce the noise of the stilled picture.
When manually adjusting the picture, automatic tracking is turned off. To turn automatic tracking
back on, eject the tape and reinsert it.
Note: Tracking has no effect when recording– only during playback.
Time Counter
The time counter shows the actual time used when recording or playing back a
tape. The time counter helps locate the beginning or end of recorded events. It
resets to 0:00:00 whenever a tape is ejected from the VCR.
For example, if you record a 30–minute program at the beginning of a tape,
rewind it, and then want to go to the end of the first program to start another
recording:
1. Press the INFO button twice to display only the time counter.
2. Press the CLEAR button to reset the time counter to 0:00:00.
3. Press the remote control’s FORWARD button (FWD on the VCR) to advance
a tape until the time counter reads 0:30:00.
4. Press the STOP button. This is the approximate end of a 30-minute program
(you may want to press the PLAY button to verify). When the tape is cued
correctly, you can begin recording.
5. Press the INFO button to remove the time counter from the screen and
return to the normal display mode.
15708270 (VR661HF)(E) 07 Ftrs 2/7/01, 4:56 PM44
VCR Features
Chapter 4 45
On-Screen Displays
Pressing the INFO button displays the status of the VCR (Stop, Play Record, etc.) as well as the
channel number, time counter position, date, time, and tape speed on the TV screen.
Note: The date and time must be set before they can be displayed.
No displays will appear
(useful for dubbing)
0:30:00
2
3
Time counter only (does
not time out)
Stop Ch 05 0:30:00
11/18/01 Sun 1:30PM SLP
1
On-screen display (times
out)
1. Press the INFO button to show the on-screen displays. The current time is
displayed in the VCR’s front panel.
2. Press INFO again to have only the time counter remain on the screen. The
time counter is also displayed in the VCR’s front panel.
3. Press INFO again to have no displays appear on the TV screen. The time
counter remains in the VCR’s display panel. This is useful for dubbing
tapes.
4. Press the INFO button again to return to the normal display. The current
time is displayed in the VCR’s display panel.
Note: Turning off the VCR also resets the displays.
15708270 (VR661HF)(E) 07 Ftrs 2/7/01, 4:56 PM45
VCR Features
46 Chapter 4
AUDIO
1 Reception: STEREO
2 Tape Playback: HI-FI
0 Exit
Audio Set-Up Features
Your VCR’s audio setup features affect both tape playback and recordings. The
features in this section are accessed through the AUDIO menu.
To Display the Audio Menu:
1. Press the MENU button to bring up the VCR MAIN MENU.
2. Press 7 to choose AUDIO.
With the AUDIO menu displayed, you are ready to select an item from the
menu to set up.
Reception
Some TV programs are broadcast with stereo audio or a Second Audio Program
(SAP) which offers a second language. The Reception feature lets you select the
type of audio you want to record. Press 1 repeatedly to switch between
Reception: STEREO, MONO, or SAP.
•STEREO– used for normal or stereo broadcast TV recording. The HI-FI
indicator lights on the VCR front panel when the VCR’s tuned station is
broadcasting in stereo.
•MONO– used if the stereo signal is weak or the sound is too noisy.
•SAP– used to hear/record a Second Audio Program instead of the normal
audio on both the Hi-Fi and linear tracks.
Tape Playback
The VCR records the same audio on both the Hi-Fi stereo and linear tracks on
the tape. Hi-Fi sound is recorded on separate left and right stereo channels.
Monaural sound is recorded on the linear track. In the AUDIO menu, press the
2 button repeatedly to switch between Tape Playback: Hi-Fi, LINEAR, and MIX.
To enjoy Hi-Fi sound, connect your VCR to a stereo television or amplifier/
receiver using the audio jacks. The Tape Playback feature lets you select which
audio you play back.
•Hi-Fi– use to play back sound recorded on the Hi-Fi tracks and for normal
use.
•LINEAR– use to play back the sound recorded on the linear monaural track,
such as a Second Audio Program, or a dubbed voice-over.
•MIX– used to play back the sound recorded on both the linear track and
the Hi-Fi track, sound-on-sound. The Hi-Fi indicator lights when MIX is
active.
15708270 (VR661HF)(E) 07 Ftrs 2/7/01, 4:56 PM46
47
Changing Entertainment. Again.
Other Information
Chapter Overview:
•Troubleshooting
•COMMERCIAL ADVANCE Q&A
•Front, Rear, and Display Panel Diagrams
•Specifications
•Care and Cleaning
•Warranty Information
•Finding the TV’s Video Line Input
•Advanced Connection Diagram
•Glossary
•Index
Chapter 5
15708270 (VR661HF)(E) 08 Other 2/7/01, 4:56 PM47
Other Information
48 Chapter 5
Troubleshooting Tips
In this section, you will find answers to common recording, playback, and general VCR questions.
Consulting with this section first when there is problem may help you answer common questions.
General VCR Problems
No power
•Check to make sure it is plugged into an operating outlet.
•Check to make sure your connections are correct.
VCR does not respond to the remote control
•Check to make sure there are no objects between the VCR and the remote control.
•The remote control’s batteries may need changing.
•You are not in VCR-controlling mode. Press the remote control’s VCR button to control it.
There’s poor or no picture for normal TV viewing
•Make sure the VCR indicator is off.
•Make sure the TV is switched to an active channel.
•Make sure the antenna connections are secure and correct.
Rewind does not operate
•Check to make sure the tape is not already rewound.
The clock shows an incorrect time or date
•There may have been a power interruption. Reset the VCR’s time and date.
•Make sure the clock is set accurately (check AM/PM and date).
•Check the Daylight-Saving setting. The clock may have adjusted for Daylight-Saving Time.
•Time did not adjust for Daylight-Saving time.
•Check to make sure the Daylight-Saving Time feature is set correctly.
The VCR makes noise when stopped
•The VCR is removing the tape from the playheads. This is normal. The head cylinder inside the VCR will
continue to rotate for a few minutes after you put the VCR in the stop mode.
Cannot select channels over 69
•Cable channels over 69 can only be selected if Signal Type: CABLE/ANTENNA feature is set to CABLE.
TIMER flashes on the VCR front panel display
•The clock is not set.
•Check to make sure there is a cassette in the VCR when a timer recording is set ad the power is turned
off.
On-screen menus appear in English, French, or Spanish
•Check the LANGUAGE feature for the preferred on-screen language.
15708270 (VR661HF)(E) 08 Other 2/7/01, 4:56 PM48
Chapter 5 49
Other Information
Recording Problems
Will not record
•Make sure there is a recordable tape in the VCR.
•Eject then reinsert the tape.
•Make sure the tape is not broken.
•Make sure the VCR is not in pause mode. Press PAUSE or PLAY to return to normal playback.
•Make sure the Pro-Tect Plus feature is not active.
A VCR Plus+ system or timer recording was not made or the wrong program recorded
•Make sure the correct PlusCode programming number is entered.
•Make sure the program was entered correctly (the wrong channel or times may be entered).
•Make sure the cable box or satellite receiver was turned on when recording was to begin.
•There may have been a power interruption. Reset the time and date.
•Check to see if time and date are correct – including AM/PM.
•Make sure the program did not exceed the tape’s length or that the tape was not rewound beforehand.
•Make sure the VCR was turned off at the time recording started.
•Make sure there was a tape in the VCR with its safety tab intact.
•The VCR ejects tapes when the end is reached during a timer recording.
•Make sure the VCR Plus+ system setup was completed correctly.
Will not record
•Make sure the tape’s safety tab is intact.
•Make sure the VCR is not in Video Line Input mode. Press INPUT on the remote control to return to
normal viewing.
Playback Problems
Snowy or no picture during playback
•Press the remote control’s TV•VCR button to activate VCR-controlling mode. VCR appears in the front
panel display when active.
•Check the TV channel selected (3 or 4) to make sure it matches the channel selected with CH. 3/4
switch on the back of the VCR.
•Check to make sure the TV’s fine tuning is correct for the channel selected.
•If you use A/V cables and jacks to connect the VCR to the TV, check all connections for snug and
correct connections.
•Check to make sure the TV monitor is set to Video Line Input (see How to Find Your TV’s Video Line
Input in this section of the manual for detailed information).
•Try another tape.
•Some snow/streaks are normal during search, stop action, frame advance, and slow-motion playback.
15708270 (VR661HF)(E) 08 Other 2/7/01, 4:56 PM49
Other Information
50 Chapter 5
Streaks in picture during normal playback
•Press one of the TRACKING buttons to move streaks up or down for the best picture.
•Check to make sure the tape is of good quality and not worn out.
Time counter not working or time counter not working in search modes
•The time counter does not advance during unrecorded portions of tape. When an unrecorded segment of tape is
encountered, the time counter will hold its count until recorded material is detected again.
•A minus (–) will appear in front of the time if you rewind the tape farther back than a counter reading of 0:00:00.
•The time counter disappears during search; this is normal.
Will not play
•Check to make sure there is a tape in the VCR.
•Try ejecting and reinserting the cassette.
•Check to make sure the tape is not broken.
•Check to make sure the VCR is not in pause mode. Press PAUSE or PLAY to return to normal playback.
•Check the Pro-Tect Plus™ feature.
Will not Auto Channel Search active channels correctly
•Check to make sure the antenna connections are secure and correct.
•Check to make sure the Signal Type: CABLE/ANTENNA feature is set correctly.
•If Detect Automatically was selected for the Signal Type in the AUTO CHANNEL SEARCH menu, try using either
CABLE TV or ANTENNA instead.
•May not be necessary if using a cable box for all channels. Contact your local cable company for more information.
Tape plays back in slow motion
•Press PLAY to return to normal playback.
Cassette with safety tab removed does not start to play automatically
•Check to make sure the AUTO PLAY ON/OFF feature is set to ON.
Time counter disappears during searching
•This is normal.
There is no stereo sound during playback
•Make sure the Tape Playback feature is set to Hi-Fi to hear stereo sound during playback.
•You must use A/V cables (not provided) and jacks to connect the VCR to the TV (or stereo) to hear true stereo
sound during playback.
The stereo Audio is too noisy
•The stereo signal is weak. Set the Reception: STEREO/SAP/MONO to MONO.
•Press either the TRACKING – or + button to minimize picture noise.
15708270 (VR661HF)(E) 08 Other 2/7/01, 4:56 PM50
Chapter 5 51
Other Information
Questions and Answers About
®
Will commercials be scanned through only on playback of recordings?
Yes. The VCR rewinds and marks commercial segments after a recording is finished.
How fast does this feature scan through commercial breaks?
In SLP tape speed, a 3-minute commercial break is scanned through in approximately 8-12
seconds. In SP, it takes about 25-35 seconds.
Are commercials still recorded if I want to watch them?
Yes. The recorded program, including commercials, can be viewed by setting the Playback
feature to MANUAL.
What if the VCR scans forward through part of my program?
Press PLAy or STOP while the tape is being automatically skipped. rewind the tape back to a
position before skipping started, then press PLAY.Automatic skipping will start again after the
end of the commercial group is detected by the VCR.
Once a recording has been marked, does COMMERCIAL ADVANCE work each time
the tape is played?
Yes. If the Playback feature is set to AUTO, the marked commercials should be skipped each
time the tape is played in a COMMERCIAL ADVANCE VCR.
After marking commercials, is the tape left at the beginning or end of the
recording?
The tape is left at the end of the recording so it is in position to begin additional programmed
recordings.
Does the marking process interfere with other programmed recordings?
No. If two or more recordings are programmed together without sufficient time to mark the
first recording, marking will take place after all recordings are completed.
What happens if the marking process is interrupted?
Marking can be interrupted to allow use of the VCR. Marking will resume again when the
VCR’s power is turned off as long as the tape has not been ejected from the VCR.
Does COMMERCIAL ADVANCE work in all recording speeds?
Yes, COMMERCIAL ADVANCE works in SP and SLP.
Will COMMERCIAL ADVANCE marked recordings work in non-Commercial Advance
VCRs?
A COMMERCIAL ADVANCE marked recording will play in a non-Commercial Advance VCR,
but commercials will not automatically be skipped.
15708270 (VR661HF)(E) 08 Other 2/7/01, 4:56 PM51
Other Information
52 Chapter 5
Front Panel
AUDIO (LEFT and RIGHT) and VIDEO In Jacks Receives signals from another component (like
another VCR or camcorder) when connected to the VCR using A/V jacks. Use the INPUT button to
select L2 to record from these jacks (L1 indicates the rear panel A/V jacks being active).
CHANNEL TRACKING Up and Down Adjusts the image quality by removing picture “noise”
and distortion.
FWD Forwards the tape when the VCR is stopped. Searches the picture forward during playback.
Starts slow motion during play-pause and increases slow-motion speed.
PLAY•PAUSE Plays a tape. Pauses action for viewing during playback. Pauses recording to
prevent recording of unwanted scenes.
POWER Turns the VCR on or off.
RECORD Starts VCR recording. Also used for Express Recording (XPR).
REV Rewinds the tape when the VCR is stopped. Searches the picture in reverse during
playback. Starts slow motion during play-pause and decreases slow-motion speed.
STOP/EJECT A single press of this button stops normal VCR functions such as record, playback,
rewind, fast-forward, or pause. If pressed a second time, this button ejects an inserted tape.
TV•VCR Switches the picture signal so that it either comes from the VCR or the TV cable/antenna
signal.
.
15708270 (VR661HF)(E) 08 Other 2/7/01, 4:56 PM52
Chapter 5 53
Other Information
Display Panel
Clock/Counter Displays current time, time counter, tape speed, or channel numbers when switching
channels.
FUNCTION DISPLAYS:
dn & Ld (Down and Load) Front panel display alternates between these two words when time data is
being downloaded.
REC (Recording indicator) The VCR is recording. REC flashes on the front panel display when a recording is
paused.
(Timer indicator) Displayed when an Express Recording (XPR) or timer recording is under way or when
the VCR is set for a timer recording and the power is turned OFF. TIMER flashes on the VCR front panel when a
timer recording is set and no tape is inserted in the VCR.
VCR indicator Indicates that the VCR is in VCR-display mode. Press the TV•VCR button to toggle between
VCR and TV viewing modes.
•VCR indicator is ON when the picture displayed is from the VCR’s tuner.
•VCR indicator is OFF when the picture displayed is from the TV’s tuner.
AM
REC
VCR
15708270 (VR661HF)(E) 08 Other 2/7/01, 4:56 PM53
Other Information
54 Chapter 5
Back Panel
CH. 3/4 switch Determines the channel to which the TV must be tuned in order to see the VCR’s
picture. Not used when connecting the VCR to the TV using A/V cables.
AUDIO (LEFT and RIGHT) and VIDEO IN jacks Receives signals from another component, such
as another VCR or camcorder, when connected to these jacks. Use the INPUT button on the VCR or
remote control to select the rear video line input A/V jacks (L1) to record from these jacks.
AUDIO (Right and Left) and VIDEO OUT jacks Sends signals from the VCR to another
component, like a TV or another VCR, when the other component is connected to these jacks.
ANT. IN jack Receives a signal from an antenna or cable system when the VCR is attached with RF
cables.
RF OUT jack Passes the VCR’s signal to a TV using the supplied RF cable.
ANT. IN
RF OUT
CH.
VIDEO
AUDIO
OUT IN
R
L
3 4
15708270 (VR661HF)(E) 08 Other 2/7/01, 4:56 PM54
Chapter 5 55
Other Information
Specifications
Format: VHS
Record/Playback Video: 4-head
System: Audio: VHS Hi-Fi record/playback system
Video Signal System: EIA standard: NTSC color
Antenna: 75-ohm external VHF/UHF combined
antenna terminal
Tuner: USA: 181 channels capability*
(125 cable channels)
Canada: 178 channels capability*
(122 cable channels)
Type: AutoProgramming frequency synthesis
Power Requirement: 120V AC, 60 Hz
Power Consumption: 17 watts (standby < 3 watts)
Dimensions: 3.64 inches high (91 mm)
14.4 inches wide (360 mm)
9.4 inches deep (230 mm)
Weight: 6.4 pounds (2.9 kg)
Other: Automatic head cleaner
Storage Temperature - 22˚F to +149˚F
Range: (-30˚C to +65˚C)
Operating +41˚F to +104˚F
Temperature Range: (+5˚C to +40˚C)
*Check your cable company‘s compatibility requirements.
Cleaning the VCR
Use a soft cloth or dusting attachment of your vacuum cleaner to dust your VCR. Remove dust from
the ventilation holes on the top, back, sides, and bottom of the VCR and all connected components.
Plastic surfaces are easily scratched and can be marred by alcohol and various solvents. Avoid
excessive use of oil-based furniture polishes since the materials used in the cabinet will accumulate
more dust. We recommend using a nonabrasive, antistatic cleaner and polisher.If part of the
program is skipped, rewind the tape to the beginning of the skipped program segment and press
PLAY.
15708270 (VR661HF)(E) 08 Other 2/7/01, 4:56 PM55
Other Information
56 Chapter 5
RCA VCR Limited Warranty
What your warranty covers:
•Any defect in materials or workmanship.
For how long after your purchase:
•90 days for labor charges.
•One year for parts.
The warranty period for rental units begins with the first rental or 45 days from date of shipment to the rental firm, whichever
comes first.
What we will do:
•Pay any Authorized RCA VCR Service Center the labor charges to repair your VCR.
•Pay any Authorized RCA VCR Service Center for the new or, at our option, refurbished replacement parts required to
repair your VCR.
How you get service:
•Take your VCR to any Authorized RCA VCR Service Center. To identify your nearest Authorized RCA VCR Service
Center, ask your dealer, look in the Yellow Pages, or call 1-800-336-1900.
•Show the Authorized Service Center Representative your evidence of purchase date or first rental.
•Pick up your VCR when repairs are completed.
What your warranty does not cover:
•Customer instruction. (Your Owner’s Manual clearly describes how to install, adjust, and operate your VCR. Any
additional information should be obtained from your dealer.)
•Installation and related adjustments.
•Signal reception problems not caused by your VCR.
•Damage from misuse or neglect.
•Cleaning of video/audio heads.
•Batteries.
•A VCR that has been modified or incorporated into other products or is used for institutional or other commercial
purposes.
•A VCR purchased or serviced outside the U.S.A.
•Acts of nature, such as but not limited to lightning damage.
Product Registration:
•Please complete and mail the Product Registration Card packed with your VCR. It will make it easier to contact you
should it ever be necessary. The return of the card is not required for warranty coverage.
How State Law relates to warranty:
•This warranty gives you specific legal rights and you also may have other rights that vary from state to state.
If you purchased your VCR unit outside the United States:
•This warranty does not apply. Contact your dealer for warranty information.
Service calls which do not involve defective materials or workmanship are not covered by this warranty. Costs
of such service calls are the sole responsibility of the purchaser.
15708270 (VR661HF)(E) 08 Other 2/7/01, 4:56 PM56
Chapter 5 57
Other Information
Finding the TV’s Video Line Input
You need to tune your TV to the video line input if you are using the
VCR’s Audio/Video (A/V) OUT jacks to connect to the TV’s A/V input
jacks. You must select the TV’s video line input before you can see the
VCR’s menus, the cable/antenna reception, and the content that’s on a
tape.
The video line input for TVs varies by brand and model. Below are some
steps to try to find your TV’s video line input:
•If your TV brand is RCA, GE, or Proscan, press the TV button on the
VCR’s remote control, then press the INPUT button.
•If you have another brand of TV, see the chapter Using the Remote
Control to see if the VCR’s remote can be programmed to control your
TV. If so, once completed, follow the step above.
If those options do not work, try the following ideas. You might access the
video line input by:
•Pressing a button on the TV’s remote control (see the table below).
•Selecting a specific channel from the TV’s on-screen menu system (see
the table below).
•Tuning directly to the video line input by selecting a specific channel
number (see the table below)
•Going through all available channels by pressing the channel up or
down buttons on the TV or its remote control.
Common Video Line Input scenarios:
I
N
P
U
T
T
V
•
V
C
R
ON•OFF
PLAY FORWARD
RECORD STOP PAUSE
F.A DV
CLEAR MENU SPEED
TRACKING
1
4
7
2
5
8
3
6
9
0
C
H
A
N
V
O
L
V
O
L
C
H
A
N
INFO SEARCH
MUTE GO BACK
TV VCR
REVERSE
INPUT
Button
TV Button
Video Input Channel Variations
Button/Switch Button on the Channel
on the TV TV Remote Number
VIDEO VID 1 00
SIGNAL LINE 90
VID 1 VID 91
VID 2 VIDEO 92
S-VID S-VID 93
S-VIDEO INPUT VID 1
S-VIDEO VID 2
SOURCE
AUX
15708270 (VR661HF)(E) 08 Other 2/7/01, 4:56 PM57
Other Information
58 Chapter 5
Advanced Connection
TV + VCR + Satellite Receiver
•Using A/V and RF Coaxial Cables
Note: Your satellite receiver and television back panels may not look exactly like the models
shown here. This connection can also be used for a cable box.
1. Connect the VCR to the TV
A. Connect one end of the supplied RF
coaxial cable to the RF OUT jack on
the back of the VCR and the other end
to the TV’s antenna input jack.
B. Connect the A/V cables. Connect audio
cables to the VCR’s R and L Audio OUT
jacks and the other ends to the TV’s
corresponding audio input jacks (if your
TV only has one audio input jack, use
the VCR’s L audio jack to connect).
Connect one end of the video cable to
the VCR’s VIDEO OUT jack, and the
other end to the TV’s video input jack.
2. Connect the satellite receiver to the VCR
A. Connect one end of a second RF coaxial
cable (not included) to the VCR’s ANT.
IN jack. Connect the other end to the
satellite receiver’s antenna output jack.
B. Connect the A/V cables. Connect audio
cables to the VCR’s R and L audio IN
jacks and the other ends to the satellite
receiver’s audio output jacks. Connect
one end of the video cable to the VCR’s
VIDEO IN jack, and the other end to
the satellite receiver’s video output
jack.
3. Connect a TV antenna or cable feed to the satellite receiver
If you have cable or a standard TV antenna, connect its RF coaxial cable (not included) to the
antenna input jack on the satellite receiver.
4. Connect the satellite antenna’s cable to the satellite receiver
Connect the satellite antenna’s RF coaxial cable feed (not included) to the receiver’s satellite
input jack.
Note: To hear stereo output from the satellite receiver, you must use the TV’s video line input
“channel.” RF coaxial cable only carries mono sound.
CH
ANT. IN
IN
OUT
AUDIO
VIDEO
3 4
RF OUT
CABLE/
ANTENNA
VCR
TV
VIDEO RL / MONO
S-VIDEO
AUDIO
L
IN
OUT
CH3
CH4
SATELLITE
RECEIVER
S-VIDEO
L
L
R
R
VIDEO
OUT
IN FROM ANT
OUT TO TV SATELLITE
IN
From
Satellite
From Cable
or TV Antenna
1A
4
3
VCR
TV
Satellite
1B
2A
2B
15708270 (VR661HF)(E) 08 Other 2/7/01, 4:56 PM58
Chapter 5 59
Other Information
Glossary
A/V Jacks & Cables Commonly called “RCA-type” cables. Improves
picture and sound quality over RF Coaxial cables. A/V cables are required
for stereo audio.
EnergySaver Automatically turns the VCR off after a user-defined
period of inactivity.
Express Recording (XPR) A method of timer recording which tapes
for a set period of time using 30-minute increments.
Pro-Tect Plus™ Allows the VCR to be disabled so that the front panel
and remote control buttons don’t work. Useful for protecting timer
recordings.
QuickSet Guide An first-time use, interactive, menu-based system that
walks you through several setup steps in a series of questions. The
QuickSet Guide is also available in the VCR’s Main Menu.
SAP (Second Audio Program) A second sound track that may be
included with a stereo broadcast. Usually used for foreign language dubs
of programs.
VCR Channels List The active list of channels available to the VCR
using the CHANNEL +/- buttons.
XPR See Express Recording above.
15708270 (VR661HF)(E) 08 Other 2/7/01, 4:56 PM59
Index
60 Chapter 5
Index
A
ADD/REMOVE CHANNELS screen
18
Audio features, set up 46
AUDIO IN jacks 58
AUDIO menu 46
Audio/Video (A/V) jacks 17, 52, 54
AUDIO/VIDEO jacks 26
Auto channel search 17
Auto clock feature 19
Auto play feature 13, 21
Auto TV/VCR feature 22
Automatic rewind 13
Automatic tracking 13, 44
B
Back panel jacks 54
Basic recording 13
Batteries (remote control) 11
Broadcast stereo TV recording 38
C
Cable box setup 16
Cables
positioning 6
CHAN buttons 27
CHANNEL buttons 17, 26
Channels, adding/removing 18
CHANNELS menu 16, 18, 35
CLEAR button 26, 27, 40
Clock display 53
COMMERCIAL ADVANCE 41
Display 42
Marking 41
Playback 42
questions and answers 51
Component buttons 26
Connections 8
Controls
back panel 54
front panel 52
Copying tapes 38
D
Date and time setting 19
Design specifications 55
Display panel 53
Displays, on screen 45
E
EJECT button 13
EnergySaver feature 22
Express Recording (XPR) 2, 32
F
F. ADV button 26, 39
FORWARD button 13, 39
Frame advance 39
Front panel controls 52
FWD button 38, 39, 44
G
Glossary 59
GO BACK button 26, 27
I
Index search 40
Indicators in display panel 53
INFO button 26, 27, 44
INPUT button 27
INPUT button 26, 33, 38, 57
L
L1 indicator 38
L2 indicator 38
LANGUAGE menu 16
Locking feature 44
M
MENU button
16, 26, 33, 35, 41, 46
MOVIE ADVANCE
Overriding 43
Movie Advance 43
MUTE button 27
N
Number buttons 20, 26, 27
O
OFF button 26, 27
ON•OFF button 44
On-screen displays 45
Overheating 6
P
PAUSE button 13, 27, 38
Picture search options 39
PLAY button 13, 27, 38
PLAY/PAUSE button 39
POWER button 13
Power surges 6
PREFERENCES menu 21, 41
Pro-Tect Plus locking feature 44
Q
QuickSet guide 16
R
REC display 53
Reception: STEREO/MONO/SAP
feature 38, 46
RECORD button 13, 27, 32, 38, 52
15708270 (VR661HF)(E) 08 Other 2/7/01, 4:56 PM60
Chapter 5 61
Index
Recording
basic 13
broadcast stereo TV 38
copying /editing tapes 38
Express (XPR) 2, 32
SAP 38
speeds 23
timer 33
Remote
component buttons 26
TV function buttons 27
Remote, batteries 11
Removing/adding channels 18
REV button 27, 38, 52
REVERSE button 13, 39
Reviewing timer programs 33
Rewind, automatic 13
RF OUT jack 54
S
Safety tab 13, 21
SAP 38
Search
forward 39
reverse 39
SEARCH button 27, 40
Set up
auto play feature 21
auto TV/VCR feature 22
cable box 16
Daylight-Saving 20
front panel 22
language feature 16
PREFERENCES menu 21
tape speed feature 23
time and date 19
time zone 19
using menu system 16
Signal type
changing 18
selecting 18
Slow motion 39
Specifications 55
Speed
SLP 23
SP 23
SPEED button 13, 23, 27, 32
Speeds, recording 23
STOP button 13, 27, 32, 38, 52
T
Tab, safety 13
Tape eject 13
Tape playback feature 46
Tape playback: HI-FI/LINEAR/MIX
46
Tape speeds 23
Time and date 19
Time counter 44
Time counter display 45
Time display on TV 45
TIME menu 19
Time setting
Daylight-saving 20
set time zone 19
Timer programs
clearing 33
reviewing 33
Timer recording 33
stopping 33
TRACK buttons 27
Tracking 44
TRACKING buttons 13, 39, 44
Troubleshooting 48
TV button 26, 57
TV function buttons 27
TV•VCR button 22, 27, 38
V
VCR
connecting 8
VCR button 26
VCR function buttons 26
VCR indicator 38, 53
VCR MAIN MENU 16, 19, 46
VCR Plus+
channel lists 36
channel worksheet 37
VCR Plus+ SILVER System 34
VCR Plus+ System Worksheet 37
VCR viewing channel 11, 13
Video Input Channel 57
VOL buttons 27
15708270 (VR661HF)(E) 08 Other 2/7/01, 4:56 PM61
Thomson multimedia Inc.
10330 North Meridian Street
Indianapolis, IN 46290
©2001 Thomson multimedia Inc.
Trademark(s)® Registered
Marca(s) Registrada(s)
Printed in Korea
TOCOM 15708270
Please do not send any products to the
Indianapolis address listed in this manual or on
the carton. This will only add delays in service
for your product.
15708270 (VR661HF)(E) 08 Other 2/8/01, 10:21 AM62