WISOL RPM2470 ZigBee Module User Manual 2 Manual final

WISOL CO., LTD ZigBee Module 2 Manual final

Users Manual

SPECIFICATION PBA RF Module Customer - Model name RP-M2470 Part name WSZGM200C00 Date 2013. 11. 13 REVISION 02 Application Set Top Box CUSTOMER-CODE - WISOL CO., LTD. 373-7, Gajang-dong Gyeonggi-do Osan 447-210 Korea http://www.wisol.co.kr
PBA RF Module WSZGM200C00 ZigBee / 2.4GHz / IEEE802.15.4 15x18x.2.5 mm3, 45pin, 1mm Pitch Version: 02 2 /14 쪽 2013. 11. 11 1. Approval Revision Record NO REASON RECORD OF REVISION Remarks Revision Page 1 REV00 WSZGM200B00 Approval Releases 2012-03-06 - 2 REV01 FCC ID / IC Number Added - FCC ID : 2ABA2RPM2470 - IC : 11534A-RPM2470 2013-11-11 - 3 REV02 FCC/IC Notice Added 2013-11-13 - 2. Scope This specification is applied to ZigBee / IEEE802.15.4 This module has Chip Antenna, 32MHz X-TAL, Single chip MG2470 3. Absolute Maximum Ratings Symbol Parameter Rating Unit VDD Chip core supply voltage -0.3 to 2.0 V 3V_IN I/O supply voltage -0.3 to 3.6 V TSTG Storage Temperature -40 to 85 ℃
PBA RF Module WSZGM200C00 ZigBee / 2.4GHz / IEEE802.15.4 15x18x.2.5 mm3, 45pin, 1mm Pitch Version: 02 3 /14 쪽 2013. 11. 11 4. DC Characteristics Symbol Parameter Min Typ. Max Unit 3V_IN I/O supply voltage(VDDIO) 2.0 3.0 3.6 V VIH High level input voltage 2.5 - 3.6 V VIL Low level input voltage 0 - 0.4 V VOH High level output voltage 2.5 - 3.6 V VOL Low level output voltage - - 0.4 V TA Air temperature -40 - 85 ℃ 5. Electrical Specification (Condition: EVM Board, at 25℃, 3V_IN=3.0V) Parameter Min Typ. Max Unit Current consumption MCU active without RX/TX operation, Peripherals [UART1 & RNG] active - 4.2 - mA TX Mode (MCU active and peripherals[UART1 & RNG] active) @ max (+9.6dBm) output power @+8dBm output power @+7dBm output power @+6dBm output power @+5dBm output power @+4dBm output power @+3dBm output power @+2dBm output power @+1dBm output power @+0dBm output power - 43 25 - mA RX Mode (MCU active and peripherals[UART1 & RNG] active) - 25 - mA
PBA RF Module WSZGM200C00 ZigBee / 2.4GHz / IEEE802.15.4 15x18x.2.5 mm3, 45pin, 1mm Pitch Version: 02 4 /14 쪽 2013. 11. 11 PM1 - 30 - uA PM2 - 1.25 2 uA PM3 - 0.1 1 uA TX / RX and RX / TX turnaround - - 192 us 6. RF Specifications 6-1. RF Characteristics Parameter Min Typ. Max Unit RF Characteristics RF Frequency Range 2405 - 2480 MHz Maximum Input Level (PER=1%) @250kbps - -1 - dBm Received RF Bandwidth - 2 - MHz Channel Bandwidth - 5 - MHz Receiver Sensitivity (PER≤1%, Packet length of 22-byte) @1000kbps @500kbps @250kbps @125kbps @62.5kbps @31.25kbps - -93 -94 -99 -100 -103 -105 - dBm Adjacent Channel Rejection +5MHz -5MHz - 30 30 - dB Alternate Channel Rejection +10MHz -10MHz - 50 50 - dB Co-Channel Rejection - -5.9 - dB
PBA RF Module WSZGM200C00 ZigBee / 2.4GHz / IEEE802.15.4 15x18x.2.5 mm3, 45pin, 1mm Pitch Version: 02 5 /14 쪽 2013. 11. 11 Blocking / Desensitization +5MHZ / -5MHz +10MHZ / -10MHz +20MHZ / -20MHz +30MHZ / -30MHz +50MHZ / -50MHz - -53/-52 -48/-46 -44/-40 -43/-38 -41/-37 - dBm TX output power * -7dBm±2dB@2480MHz 6 8 9.6 dBm Transmit chip rate - 2 - Mcps Spurious Emission(30Hz~1GHz) - -60 - dBm Spurious Emission(1GHz~12.75GHz) - -45 - dBm Spurious Emission(5.15GHz~5.3GHz) - -70 - dBm 2nd Harmonics - -45 - dBm 3nd Harmonics - -55 - dBm Frequency Error Tolerance - - ±200 KHz Error Vector Magnitude(EVM) - 8.5 - % Frequency Synthesizer Phase Noise (Unmodulated carrier) @±100KHz offset @±1MHz offset @±2MHz offset @±3MHz offset @±5MHz offset - -79.9 -104.2 -110.0 -113.8 -115.6 - dBc/HzPLL Lock Time - - 192 usec 32MHz Crystal Oscillator Crystal Frequency - 32 - MHz Crystal Frequency Accuracy Requirement -40 - +40 ppm Data rate - 250 - kbps
PBA RF Module WSZGM200C00 ZigBee / 2.4GHz / IEEE802.15.4 15x18x.2.5 mm3, 45pin, 1mm Pitch Version: 02 6 /14 쪽 2013. 11. 11 6-2. Analog Temperature Parameter Min Typ Max Unit Analog Temperature Output Voltage at -40℃ - 716 - mV Output Voltage at 0℃ - 847 - mV Output Voltage at 40℃ - 978 - mV Output Voltage at 80℃ - 1109 - mV Temperature Coefficient - 3.275 - mV/℃ ※ All measurement results are obtained using the 12 bit ADC Analog Temperature Input Voltage 0 - VDD V Input Resistance - 150 - kΩ Full-scale signal - - 3 V Effective number of bits(ENOB) Single-ended input, 12bit setting - 10.8 - bits Effective noise and distortion(SINAD) Single-ended input, 12bit setting - 66.78 - dB Current Consumption - 0.62 - mA Internal Reference Voltage - 1.25 - V
PBA RF Module WSZGM200C00 ZigBee / 2.4GHz / IEEE802.15.4 15x18x.2.5 mm3, 45pin, 1mm Pitch Version: 02 7 /14 쪽 2013. 11. 11 7. Specification on Chip Antenna
PBA RF Module WSZGM200C00 ZigBee / 2.4GHz / IEEE802.15.4 15x18x.2.5 mm3, 45pin, 1mm Pitch Version: 02 8 /14 쪽 2013. 11. 11 8. Pin Description Terminal NAME Inter face I/O Description 1 ACH0 Analog I/O Sensor ADC input 2 ACH1 Analog I/O Sensor ADC input 3 ACH2 Analog I/O Sensor ADC input 4 ACH3 Analog I/O Sensor ADC input 5 NC - - - 6 AGND Ground - RF Ground 7 AGND Ground - RF Ground 8 AGND Ground - RF Ground 9 MS2 Digital I Mode select 10 NC - - - 11 RESETB Digital I Reset (Active Low) 12 3V_IN Power I 3V Power supply 13 DGND Ground - Ground for digital core and I/O 14 P1[7] Digital O Port P1.7GPO/P0AND/TRSW/Fold/Clock/BIST Fail Indicator15 P1[6] Digital B Port P1.6/TRSWB 16 NC - - - 17 P1[4] Digital B Port P1.4 /QUADZB/Sleep Timer OSC Buffer Input. 18 P1[3] Digital B Port P1.3/QUADZA/Sleep Timer OSC Buffer Output/RTCLKOUT 19 NC - - - 20 P1[1] Digital B Port P1.1/TXD1 21 P1[0] Digital B Port P1.0/RXD1 22 P3[7] Digital B Port P3.7/12mA Drive capability /PWM3/CTS1/SPICSN(slave only) 23 P3[6] Digital B Port P3.6/12 mA Drive capability /PWM2/RTS1/SPICLK
PBA RF Module WSZGM200C00 ZigBee / 2.4GHz / IEEE802.15.4 15x18x.2.5 mm3, 45pin, 1mm Pitch Version: 02 9 /14 쪽 2013. 11. 11 Terminal NAME Inter face I/O Description 24 P3[5] Digital B Port P3.5/T1/CTS0/QUADYB/SPIDO 25 P3[4] Digital B Port P3.4/T0/RTS0/QUADYA/SPIDI 26 P3[3] Digital B Port P3.3/INT1(active low) 27 P3[2] Digital B Port P3.2/INT0(active low) 28 P3[1] Digital B Port P3.1/TXD0/QUADXB 29 P3[0] Digital B Port P3.0/RXD0/QUADXA 30 DGND Ground - Ground for digital core and I/O 31 NC - - - 32 P0[7] Digital B Port P0.7/I2STX_MCLK 33 P0[6] Digital B Port P0.6/I2STX_BCLK 34 P0[5] Digital B Port P0.5/I2STX_LRCK 35 P0[4] Digital B Port P0.4/I2STX_DO 36 P0[3] Digital B Port P0.3/I2SRX_MCLK 37 P0[2] Digital B Port P0.2/I2SRX_BCLK 38 P0[1] Digital B Port P0.1/I2SRX_LRCK 39 P0[0] Digital B Port P0.0/I2SRX_DI 40,41,42 AGND Ground - RF Ground 43,44,45 AGND Ground - RF Ground 46,49 AGND Ground - RF Ground 47,48 DGND Ground - Ground for digital core and I/O
PBA RF Module WSZGM200C00 ZigBee / 2.4GHz / IEEE802.15.4 15x18x.2.5 mm3, 45pin, 1mm Pitch Version: 02 10 /14 쪽 2013. 11. 11 9. Dimensions & drawing 9-1. Design dimension ※ Table A: Real dimension specification ITEM Width Length Design 15 mm 18 mm Real dimension value 14.90mm(*) 17.90mm(*) (*) : 0.1mm is cut by Dicing blade 9-2. PCB Drawing -1 (Top View) Pads of pin 46,49 ; (R=0.75, Circle) Pads of pin 47,48 ; (R=0.625, Circle)0.8mmPads of pin 1~45 ; (W*L: 0.65*1.6mm) Silk (w=0.15mm) Table A 1mm Weight : 1.04g
PBA RF Module WSZGM200C00 ZigBee / 2.4GHz / IEEE802.15.4 15x18x.2.5 mm3, 45pin, 1mm Pitch Version: 02 11 /14 쪽 2013. 11. 11 9-3. PCB Drawing -2 (Top View)
PBA RF Module WSZGM200C00 ZigBee / 2.4GHz / IEEE802.15.4 15x18x.2.5 mm3, 45pin, 1mm Pitch Version: 02 12 /14 쪽 2013. 11. 11 9-4. Solder mask opening guide 9-5. Setup guide for an host devices to install the module PAD TYPE PAD SIZE MASK open RESULT W: 0.65mm L: 1.60mm W:0.615mm L:1.76~1.8mm W: About 95% L: About 110~115% R=0.75mm R=0.35mm 46.7% R=0.625mm R=0.25mm 40%
PBA RF Module WSZGM200C00 ZigBee / 2.4GHz / IEEE802.15.4 15x18x.2.5 mm3, 45pin, 1mm Pitch Version: 02 13 /14 쪽 2013. 11. 11 10. FCC Notice Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: ● Reorient or relocate the receiving antenna. ● Increase the separation between the equipment and receiver. ● Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ● Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter. USERS MANUAL OF THE END PRODUCT: In the users manual of the end product, the end user has to be informed to keep at least 20cm separation with the antenna while this end product is installed and operated. The end user has to be informed that the FCC radio-frequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. If the size of the end product is smaller than 8x10cm, then additional FCC part 15.19 statement is required to be available in the users manual: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. LABEL OF THE END PRODUCT: The final end product must be labeled in a visible area with the following " Contains FCC ID: 2ABA2RPM2470 ". If the size of the end product is larger than 8x10cm, then the following FCC part 15.19 statement has to also be available on the label: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.
PBA RF Module WSZGM200C00 ZigBee / 2.4GHz / IEEE802.15.4 15x18x.2.5 mm3, 45pin, 1mm Pitch Version: 02 14 /14 쪽 2013. 11. 11 11. IC Notice IC Statement This Class B digital apparatus complies with Canadian ICES-003. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil numérique de la classe B est conforme á la norme NMB-003 du Canada. IC Radiation Exposure Statement: This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter. IMPORTANT NOTE: This module is intended for OEM integrator. The OEM integrator is still responsible for the IC compliance requirement of the end product, which integrates this module. 20cm minimum distance has to be able to be maintained between the antenna and the users for the host this module is integrated into. Under such configuration, the IC RSS-102 radiation exposure limits set forth for an population/uncontrolled environment can be satisfied. Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. LABEL OF THE END PRODUCT: The final end product must be labeled in a visible area with the following " Contains IC : 11534A-RPM2470".

Navigation menu