WISOL RPM2470 ZigBee Module User Manual 2 Manual final

Download:
Mirror Download [FCC.gov]
Document ID	2130519
Application ID	Gs1FAltnXBbd5cYYgT8Gtw==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	33.04kB (413004 bits)
Date Submitted	2013-11-28 00:00:00
Date Available	2014-05-27 00:00:00
Creation Date	2013-11-13 19:59:46
Producing Software	Acrobat Distiller 10.1.7 (Windows)
Document Lastmod	2013-11-13 19:59:46
Document Title	Microsoft Word - 2.Manual_final
Document Creator	PScript5.dll Version 5.2.2
Document Author:	BDC5B9CEC3B6

SPECIFICATION
PBA RF Module
Customer
Model name
RP-M2470
Part name
WSZGM200C00
Date
2013. 11. 13
REVISION
02
Application
Set Top Box
CUSTOMER-CODE
WISOL CO., LTD.
373-7, Gajang-dong Gyeonggi-do Osan 447-210 Korea
http://www.wisol.co.kr
PBA RF Module
WSZGM200C00
ZigBee / 2.4GHz / IEEE802.15.4
15x18x.2.5 mm , 45pin, 1mm Pitch
Version: 02
1. Approval Revision Record
NO
REASON
REV00
RECORD OF REVISION
Remarks
Revision Page
WSZGM200B00 Approval Releases
2012-03-06
REV01
FCC ID / IC Number Added
- FCC ID : 2ABA2RPM2470
- IC : 11534A-RPM2470
2013-11-11
REV02
FCC/IC Notice Added
2013-11-13
2. Scope
This specification is applied to ZigBee / IEEE802.15.4
This module has Chip Antenna, 32MHz X-TAL, Single chip MG2470
3. Absolute Maximum Ratings
Symbol
Parameter
Rating
Unit
VDD
Chip core supply voltage
-0.3 to 2.0
3V_IN
I/O supply voltage
-0.3 to 3.6
TSTG
Storage Temperature
-40 to 85
℃
2 /14 쪽
2013. 11. 11
PBA RF Module
WSZGM200C00
ZigBee / 2.4GHz / IEEE802.15.4
15x18x.2.5 mm , 45pin, 1mm Pitch
Version: 02
4. DC Characteristics
Symbol
Parameter
Min
Typ.
Max
Unit
3V_IN
I/O supply voltage(VDDIO)
2.0
3.0
3.6
VIH
High level input voltage
2.5
3.6
VIL
Low level input voltage
0.4
VOH
High level output voltage
2.5
3.6
VOL
Low level output voltage
0.4
TA
Air temperature
-40
85
℃
5. Electrical Specification
(Condition: EVM Board, at 25℃, 3V_IN=3.0V)
Parameter
Min
Typ.
Max
Unit
4.2
mA
mA
mA
Current consumption
MCU active without RX/TX operation,
Peripherals [UART1 & RNG] active
TX Mode
(MCU active and peripherals[UART1 & RNG] active)
43
@ max (+9.6dBm) output power
@+8dBm output power
@+7dBm output power
@+6dBm output power
@+5dBm output power
@+4dBm output power
@+3dBm output power
@+2dBm output power
@+1dBm output power
@+0dBm output power
25
RX Mode
(MCU active and peripherals[UART1 & RNG] active)
3 /14 쪽
25
2013. 11. 11
PBA RF Module
WSZGM200C00
ZigBee / 2.4GHz / IEEE802.15.4
15x18x.2.5 mm , 45pin, 1mm Pitch
Version: 02
PM1
30
uA
PM2
1.25
uA
PM3
0.1
uA
TX / RX and RX / TX turnaround
192
us
Min
Typ.
Max
Unit
2405
2480
MHz
Maximum Input Level (PER=1%) @250kbps
-1
dBm
Received RF Bandwidth
MHz
Channel Bandwidth
MHz
dBm
6. RF Specifications
6-1. RF Characteristics
Parameter
RF Characteristics
RF Frequency Range
Receiver Sensitivity
(PER≤1%, Packet length of 22-byte)
@1000kbps
@500kbps
@250kbps
@125kbps
@62.5kbps
@31.25kbps
-93
-94
-99
-100
-103
-105
Adjacent Channel Rejection
+5MHz
-5MHz
30
30
dB
+10MHz
-10MHz
50
50
dB
-5.9
dB
Alternate Channel Rejection
Co-Channel Rejection
4 /14 쪽
2013. 11. 11
PBA RF Module
WSZGM200C00
ZigBee / 2.4GHz / IEEE802.15.4
15x18x.2.5 mm , 45pin, 1mm Pitch
Blocking / Desensitization
+5MHZ / -5MHz
+10MHZ / -10MHz
+20MHZ / -20MHz
+30MHZ / -30MHz
+50MHZ / -50MHz
TX output power
Version: 02
-53/-52
-48/-46
-44/-40
-43/-38
-41/-37
dBm
9.6
dBm
Transmit chip rate
Mcps
Spurious Emission(30Hz~1GHz)
-60
dBm
Spurious Emission(1GHz~12.75GHz)
-45
dBm
Spurious Emission(5.15GHz~5.3GHz)
-70
dBm
2nd Harmonics
-45
dBm
3nd Harmonics
-55
dBm
Frequency Error Tolerance
±200
KHz
Error Vector Magnitude(EVM)
8.5
Phase Noise
(Unmodulated carrier)
@±100KHz offset
@±1MHz offset
@±2MHz offset
@±3MHz offset
@±5MHz offset
-79.9
-104.2
-110.0
-113.8
-115.6
dBc/Hz
PLL Lock Time
192
usec
32
MHz
-40
+40
ppm
250
kbps
* -7dBm±2dB@2480MHz
Frequency Synthesizer
32MHz Crystal Oscillator
Crystal Frequency
Crystal Frequency Accuracy Requirement
Data rate
5 /14 쪽
2013. 11. 11
PBA RF Module
WSZGM200C00
ZigBee / 2.4GHz / IEEE802.15.4
15x18x.2.5 mm , 45pin, 1mm Pitch
Version: 02
6-2. Analog Temperature
Parameter
Min
Typ
Max
Unit
Output Voltage at -40℃
716
mV
Output Voltage at 0℃
847
mV
Output Voltage at 40℃
978
mV
Output Voltage at 80℃
1109
mV
Temperature Coefficient
3.275
mV/℃
Input Voltage
VDD
Input Resistance
150
kΩ
Full-scale signal
Effective number of bits(ENOB)
Single-ended input, 12bit setting
10.8
bits
Effective noise and distortion(SINAD)
Single-ended input, 12bit setting
66.78
dB
Current Consumption
0.62
mA
Internal Reference Voltage
1.25
Analog Temperature
※ All measurement results are obtained using the 12 bit ADC
Analog Temperature
6 /14 쪽
2013. 11. 11
PBA RF Module
ZigBee / 2.4GHz / IEEE802.15.4
WSZGM200C00
15x18x.2.5 mm , 45pin, 1mm Pitch
Version: 02
7. Specification on Chip Antenna
7 /14 쪽
2013. 11. 11
PBA RF Module
WSZGM200C00
ZigBee / 2.4GHz / IEEE802.15.4
15x18x.2.5 mm , 45pin, 1mm Pitch
Version: 02
8. Pin Description
Terminal
NAME
Inter face
I/O
Description
ACH0
Analog
I/O
Sensor ADC input
ACH1
Analog
I/O
Sensor ADC input
ACH2
Analog
I/O
Sensor ADC input
ACH3
Analog
I/O
Sensor ADC input
NC
AGND
Ground
RF Ground
AGND
Ground
RF Ground
AGND
Ground
RF Ground
MS2
Digital
Mode select
10
NC
11
RESETB
Digital
Reset (Active Low)
12
3V_IN
Power
3V Power supply
13
DGND
Ground
Ground for digital core and I/O
14
P1[7]
Digital
Port P1.7GPO/P0AND/TRSW/Fold/Clock/BIST Fail Indicator
15
P1[6]
Digital
Port P1.6/TRSWB
16
NC
17
P1[4]
Digital
Port P1.4 /QUADZB/Sleep Timer OSC Buffer Input.
18
P1[3]
Digital
Port P1.3/QUADZA/Sleep Timer OSC Buffer
Output/RTCLKOUT
19
NC
20
P1[1]
Digital
Port P1.1/TXD1
21
P1[0]
Digital
Port P1.0/RXD1
22
P3[7]
Digital
Port P3.7/12mA Drive capability
/PWM3/CTS1/SPICSN(slave only)
23
P3[6]
Digital
Port P3.6/12 mA Drive capability /PWM2/RTS1/SPICLK
8 /14 쪽
2013. 11. 11
PBA RF Module
WSZGM200C00
ZigBee / 2.4GHz / IEEE802.15.4
15x18x.2.5 mm , 45pin, 1mm Pitch
Terminal
NAME
Inter face
I/O
24
P3[5]
Digital
Port P3.5/T1/CTS0/QUADYB/SPIDO
25
P3[4]
Digital
Port P3.4/T0/RTS0/QUADYA/SPIDI
26
P3[3]
Digital
Port P3.3/INT1(active low)
27
P3[2]
Digital
Port P3.2/INT0(active low)
28
P3[1]
Digital
Port P3.1/TXD0/QUADXB
29
P3[0]
Digital
Port P3.0/RXD0/QUADXA
30
DGND
Ground
Ground for digital core and I/O
31
NC
32
P0[7]
Digital
Port P0.7/I2STX_MCLK
33
P0[6]
Digital
Port P0.6/I2STX_BCLK
34
P0[5]
Digital
Port P0.5/I2STX_LRCK
35
P0[4]
Digital
Port P0.4/I2STX_DO
36
P0[3]
Digital
Port P0.3/I2SRX_MCLK
37
P0[2]
Digital
Port P0.2/I2SRX_BCLK
38
P0[1]
Digital
Port P0.1/I2SRX_LRCK
39
P0[0]
Digital
Port P0.0/I2SRX_DI
40,41,42
AGND
Ground
RF Ground
43,44,45
AGND
Ground
RF Ground
46,49
AGND
Ground
RF Ground
47,48
DGND
Ground
Ground for digital core and I/O
Version: 02
Description
9 /14 쪽
2013. 11. 11
PBA RF Module
ZigBee / 2.4GHz / IEEE802.15.4
WSZGM200C00
15x18x.2.5 mm , 45pin, 1mm Pitch
Version: 02
9. Dimensions & drawing
9-1. Design dimension
Table A
Weight : 1.04g
※ Table A: Real dimension specification
ITEM
Width
Length
Design
15 mm
18 mm
Real dimension value
14.90mm(*)
17.90mm(*)
(*) : 0.1mm is cut by Dicing blade
9-2. PCB Drawing -1 (Top View)
Pads of pin 1~45 ; (W*L: 0.65*1.6mm)
Pads of pin 46,49 ; (R=0.75, Circle)
Pads of pin 47,48 ; (R=0.625, Circle)
Silk (w=0.15mm)
0.8mm
1mm
10 /14 쪽
2013. 11. 11
PBA RF Module
ZigBee / 2.4GHz / IEEE802.15.4
WSZGM200C00
15x18x.2.5 mm , 45pin, 1mm Pitch
Version: 02
9-3. PCB Drawing -2 (Top View)
11 /14 쪽
2013. 11. 11
PBA RF Module
WSZGM200C00
ZigBee / 2.4GHz / IEEE802.15.4
15x18x.2.5 mm , 45pin, 1mm Pitch
Version: 02
9-4. Solder mask opening guide
PAD TYPE
PAD SIZE
W: 0.65mm
L: 1.60mm
MASK open
W:0.615mm
L:1.76~1.8mm
RESULT
W: About 95%
L: About 110~115%
R=0.75mm
R=0.35mm
46.7%
R=0.625mm
R=0.25mm
40%
9-5. Setup guide for an host devices to install the module
12 /14 쪽
2013. 11. 11
PBA RF Module
ZigBee / 2.4GHz / IEEE802.15.4
WSZGM200C00
15x18x.2.5 mm , 45pin, 1mm Pitch
Version: 02
10. FCC Notice
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one of the following measures:
● Reorient or relocate the receiving antenna.
● Increase the separation between the equipment and receiver.
● Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
● Consult the dealer or an experienced radio/TV technician for help.
FCC Caution:
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This
device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter.
USERS MANUAL OF THE END PRODUCT:
In the users manual of the end product, the end user has to be informed to keep at least 20cm separation with the
antenna while this end product is installed and operated. The end user has to be informed that the FCC radiofrequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be
informed that any changes or modifications not expressly approved by the manufacturer could void the user's
authority to operate this equipment. If the size of the end product is smaller than 8x10cm, then additional FCC part
15.19 statement is required to be available in the users manual: This device complies with Part 15 of FCC rules.
Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this
device must accept any interference received, including interference that may cause undesired operation.
LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following " Contains FCC ID: 2ABA2RPM2470
". If the size of the end product is larger than 8x10cm, then the following FCC part 15.19 statement has to also be
available on the label: This device complies with Part 15 of FCC rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference
received, including interference that may cause undesired operation.
13 /14 쪽
2013. 11. 11
PBA RF Module
ZigBee / 2.4GHz / IEEE802.15.4
WSZGM200C00
15x18x.2.5 mm , 45pin, 1mm Pitch
Version: 02
11. IC Notice
IC Statement
This Class B digital apparatus complies with Canadian ICES-003.
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device
must accept any interference, including interference that may cause undesired operation of the device.
Cet appareil numérique de la classe B est conforme á la norme NMB-003 du Canada.
IC Radiation Exposure Statement:
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or
transmitter.
IMPORTANT NOTE:
This module is intended for OEM integrator. The OEM integrator is still responsible for the IC compliance
requirement of the end product, which integrates this module.
20cm minimum distance has to be able to be maintained between the antenna and the users for the host this
module is integrated into. Under such configuration, the IC RSS-102 radiation exposure limits set forth for an
population/uncontrolled environment can be satisfied.
Any changes or modifications not expressly approved by the manufacturer could void the user's authority to
operate this equipment.
LABEL OF THE END PRODUCT: The final end product must be labeled in a visible area with the following "
Contains IC : 11534A-RPM2470".
14 /14 쪽
2013. 11. 11

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : 
Create Date                     : 2013:11:13 19:59:46+09:00
Modify Date                     : 2013:11:13 19:59:46+09:00
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Format                          : application/pdf
Creator                         : 
Title                           : Microsoft Word - 2.Manual_final
Creator Tool                    : PScript5.dll Version 5.2.2
Producer                        : Acrobat Distiller 10.1.7 (Windows)
Document ID                     : uuid:5221e1b6-4f5b-4308-8377-4aed782b45b5
Instance ID                     : uuid:19f060e8-1932-4aa4-95de-6df4cf658a02
Page Count                      : 14

EXIF Metadata provided by EXIF.tools