WOOSIM SYSTEMS PORTI-SW40 Digital Transmission System User Manual Operator Manual Porti SW40
Woosim System Inc. Digital Transmission System Operator Manual Porti SW40
Users Manual
MODEL PORTI-SW40 WOOSIM SYSTEMS Inc. #501, Daerung Technotown 3th, 448, Gasan-Dong, GeumChun-Ku, Seoul, Korea Tel : +82-2-2107-3700 Fax : +82-2-2107-3707 URL: http://www.woosim.com All specifications are subjected to change without notice http://www.woosim.com Copyright PORTI-SW40 portable printer operator’s manual. Copyright གྷ2007 by Woosim System Inc. All rights reserved. The information contained in this manual is the property of Woosim Systems Inc. and may not be reproduced in whole or in part without the prior written permission of Woosim Systems Inc. Trademark a registered trademark of Woosim Systems Inc. All other trademark are the properties of their respective companies. Caution Some semiconductor devices are easily damaged by static electricity. You should turn the printer “OFF”, before you connect or removed the cable on the rear side, in order to guard the printer against the static electricity. If the printer is damaged by the static electricity, you should turn the printer “OFF”. Notice The contents of this manual are subject to change without notice. "Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment." http://www.woosim.com Introduction The PORTI-SW40 is suitable designed for use with a growing variety of mobile devices. IrDA/Serial or Bluetooth/Serial interfaces make the PORTI-SW40 the perfect comrade for applications such as point of transaction warehousing, distribution, point of sales, hospitality, gaming and healthcare. The general features of PORTI-SW40 printer are as follows: X Pocket size (107.5mm x 88.5mm x 45mm). X Light weight(360g) for true mobility. X Very silent printing thru direct thermal printing method. X High speed (40mm/sec) X High resolution (203dpi, 8dot/mm) X RS-232C or TTL , Bluetooth interface X Easier paper roll loading by CLAMSHELL design. X Easier maintenance with self-diagnostic. X Microsoft Windows 98/ME/XP/2000 compatible. X Support bit-image(logo) download. X Flow control : Software (XON/XOFF) ଖ Hardware flow control not supported in printer. http://www.woosim.com Operating Precaution Please follow the precautions below to enjoy and maintain the full performance of the printer. X Using the Printer Ɣ Be careful not to drop or bump the printer on a hard surface. Ɣ Do not install the printer in direct sunlight or such areas. Suitable environment for the use of the printer is as follows : ଝ Operating temperature :-10°C to 40°C ଝ Relative humidity : 10% to 90% (No condensation) Ɣ Do not install the printer near devices that generate strong electromagnetic fields such as a copy machine. Ɣ Do not open the platen cover during printing . Ɣ Do not remove or reinstall the communication cable during printing or transmission. Ɣ Do not touch the connectors of the communication cable and to close up the Infrared transmitter /receiver during printing. Ɣ Switch the POWER OFF when not in use. Ɣ Do not use alcohol or other solvent. Ɣ The AC adapter, the battery charger and the battery pack may become warm when in use. This is normal and is not a malfunction. Ɣ When the battery pack is used at low temperature, the length of time the printer can be used may be shortened. http://www.woosim.com X Thermal Paper Handling Ɣ Store the thermal paper in a cool, dry and dark place. Ɣ Do not rub the paper with hard object. Ɣ Do not leave the paper with hard object. Ɣ Do not allow plastic film, erasers, or adhesive tape to touch the paper for long periods. Ɣ Do not stack the thermal paper with diazo copies immediately after copying or wet-type copies. Ɣ Do not use chemical glue. Ɣ Always use the clean thermal paper. Note This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 the FCC Rules. These limits are designed to provide reasonable protection against farmful interference in a residential installation. Thes equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interfrernce to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause farmful interference to radio or television reception , which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: --Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver. --Connect the equipment into an outlet on a circuit different from that to which the reciver is connected. --Consult the dealer or an experienced radio/TV technician for help. Modifications not expressly approved by the manufacturer could void the user's authority to operated the equipment under FCC rules. http://www.woosim.com CONTENTS 1. Outline ............................................................................................................................................7G 1.1. Model classifications ............................................................................................................7G 1.2. Product Part Number System................................................................................................7G 1.3. Specifications........................................................................................................................8G 2. Setting up the printer ....................................................................................................................9G 2.1. Printer & Accessories ...........................................................................................................9G 2.2. Printer Features...................................................................................................................10G 2.2.1. Part name .................................................................................................................10G 2.2.2. Dimensions ..............................................................................................................10G 2.3. Replacing paper roll............................................................................................................11G 2.4. Power supply ......................................................................................................................12G 2.4.1. Internal power supply ..............................................................................................12G 2.4.2. Installing the Battery................................................................................................12G 2.4.3. Recharging the battery pack.....................................................................................13G 2.5. Set operation mode .............................................................................................................14G 3. Interface........................................................................................................................................17G 3.1. RS-232C .............................................................................................................................17G 3.2. Bluetooth ............................................................................................................................18G 4. Using the printer ..........................................................................................................................19G 4.1. Control panel ......................................................................................................................19G 4.2. Self test ...............................................................................................................................20G 5. Consumable parts ........................................................................................................................21G 5.1. Recommended paper...........................................................................................................21G 5.2. Printing position..................................................................................................................21G http://www.woosim.com 1. Outline 1.1. Model classifications PORTI-SW40 ) ( Model Name Interface None : IrDA/Serial BT : Bluetooth/Serial Power None : DC 8.4V 1.2. Product Part Number System Model name 2. Porti-SC30 Interface Spec. Wired S40 SC30 W25 Example) 1. Porti-S40 Serial/Bluetooth Wireless RS-232C Bluetooth TTL IrDA USB HPIR RS-485 None Parallel None Part No. ൽ S40/A1 Bluetooth Only Part No. ൽG SC30/Z1 http://www.woosim.com 1.3. Specifications Item Specification Printing method Direct thermal line printing Characters per line 64cpl Character size Eng. : 9*24dots, 12*24dots Resolution 203dpi, 8dots/mm Print width 3-inch (72mm, 576dots) Printing speed 40mm / sec Dimensions 107.5 * 88.5 * 45 mm Weight 360g Interface RS-232C or TTL / Bluetooth Paper supplied Thermal roll paper (80mm wide, 38ø) Barcode supplied Receive buffer size Note Kor. : 16*24dots, [24*24dots] (Including battery & roll paper) PDF417(2-dimension), Code128, Code39, I2/5, Code93 UPC, EAN, KAN, JAN, CODABAR 10K bytes Printing speed may be slower, depending on the data transmission speed and the combination of control commands. Battery Rechargeable 7.4V DC, 1400mAh(Li-ion) Battery duration 1 hour continuous printing Battery Charger Environment Conditions MCBF (Mean Cycle Between failure) Input (100~250VAC, 50~60Hz) Output(8.4VDC/0.8A), 4hours full charge time Temperature Humidity Mechanical Head -10¶C ~ 40¶C (operating) -10¶C ~ 70¶C (storage) 30% - 80% (operating) 10% - 90% (storage) 37,000,000 lines Approximately 50 Km http://www.woosim.com 2. Setting up the printer 2.1. Printer & Accessories Your printer box should include these items. If any items are damaged or missing, please contact your dealer for assistance. Battery Pack Roll Paper PORTI-SW40 Battery Charger ̷G OPTIONAL Extra Charger Communication Cable http://www.woosim.com 2.2. Printer Features 2.2.1. Part name 2.2.2. Dimensions http://www.woosim.com 10 2.3. Replacing paper roll Note : Be sure to use paper rolls that meet the specifications. Do not use paper rolls that have the paper glued to the core because the printer cannot detect the paper end correctly. 1. Make sure that the printer is not receiving data; otherwise, data may be lost. 2. Open the paper cover using finger on both side of printer, and remove the remaining paper. 3. Insert the paper roll as shown. 4. Tear the excess paper off using the edge of paper door as a tear bar. http://www.woosim.com 11 2.4. Power supply 2.4.1. Internal power supply The following specification is requested for Power supply. Battery Charger : DC 8.4V/0.8A Avoid using power supply which its power capacity of power current is extremely high. 2.4.2. Installing the Battery G NOTE : Ɣ Before installing or removing the battery pack, ensure the printer is OFF. Ɣ If the printer is not used for long period of time, remove the battery pack from the printer. ྙ To install battery pack, proceed as follows: - Insert the Battery pack in the direction of the arrow. ྚG Removing the battery pack - Turn the printer power off and push the battery pack lock and to lift up the direction of the arrow. ྛ The battery pack install into extra charger. - Insert the Battery pack in the direction of the arrow. http://www.woosim.com 12 2.4.3. Recharging the battery pack For recharging the battery pack, install the battery pack in the printer or the extra charger. Insert the Battery Charger to the charge connector of the printer or the extra charger. ٻ ٻ NOTE : Ɣ While charging the printer, turn off the printer power. Ɣ Do not remove the battery during charging. Ɣ The battery is consumable parts and when purchasing, compared to the use hour is gradually decreases. (Warranty 6 month) Ɣ If the printer is not used for a long time, unplug the power cord from the printer and outlet. Ɣ The recharging time depends on the voltage level and ambient temperature of the battery. Normally, if takes about 4 to 5 hours to recharge a battery pack. Ɣ Red Lamp : charging the battery. Green Lamp: charging is finished. http://www.woosim.com 13 2.5. Set operation mode 1. Press the MODE Button until the Error Lamp twinkles 5 times. 2. Change the mode and option using the MODE Button according to the MODE (Table1). z MODE button : use for changing OPTION status. (Error Lamp) z FEED button : use for changing MODE status. (Power Lamp) Ex) The defaults of the printer are : RS-232C/ 9600 bps/ 8 data bit / No parity / Density Low If a user wants to modify the defaults with Protocol IrDA / 38400 bps / 7 data bit/ even parity/ density high X Press MODE Button until Error Lamp twinkles 5 times and release the button. o You will see the Power Lamp twinkles one time and the Error Lamp twinkles 1 time. o Press the MODE Button one time and the Error Lamp twinkles twice. (The interface mode has set to Protocol IrDA mode) X Press FEED button one time, Power Lamp twinkles twice and Error Lamp twinkles 4 times o Press MODE Button one time, Error Lamp twinkles 5 times and press the MODE Button one more time, the Error Lamp twinkles 6 times (The baud rate has set to 38,400 bps) http://www.woosim.com 14 X Press FEED Button one time, Power Lamp twinkles 3 times and Error Lamp twinkles 2 times. o Press MODE Button one time, Error Lamp twinkles one time. (The Data Bit has set to 7 data bit) X Press FEED Button one time, Power Lamp twinkles 4 times and Error Lamp twinkles 1 time. o Press MODE Button one time, Error Lamp twinkles 2 times. (The Parity bit has set to even parity bit) X Press FEED Button one time, Power Lamp twinkles 5 times and Error Lamp twinkles 1 time. o Press MODE Button one time, Error Lamp twinkles 2 times after then press MODE Button again, the Error Lamp will twinkle 3 times. ( The density has set to High) If all the mode have set, press the MODE Button and the FEED Button at the same time after then release the buttons at the same time. The printer will print out the mode status which has modified. (PROTOCOL IrDA/ 38,400 BAUD/ 7 DATA BIT/ EVEN PARITY/ DENSITY HIGH) If the status is not correct, please try it again according to the procedure. http://www.woosim.com 15 tvklG Communication Port Baud Rate Data Bit Parity Bit Density POWER Lamp ERROR Lamp (Green) (Red) Protocol Mark Option RS-232C Protocol IrDA / Protocol Bluetooth Standard IrDA / Bluetooth 1200 bps 2400 bps 4800 bps 9600 bps 19200 bps 38400 bps 57600 bps 9600 bps 7 Data bit 8 Data bit No Parity Even Parity Odd Parity Density Low Density Medium Density High Default Protocol Lotte Protocol No use Use (Fig.1.9) http://www.woosim.com 16 3. Interface 3.1. RS-232C The PORTI-SW40 printer has a RS-232C interface and is connected by means of a 4 pin mini USB socket. In the following table, the signals present on the Mini USB socket are listed: Pin No. Name Direction Function TxD Output Transmit Data RxD Input Receive Data CTX GND Ground * Applicable connector : SUNG KYUNG (CM-720) NOTE : Ɣ When data receiving, when it removes the communication cable, it loses a data. http://www.woosim.com 17 3.2. Infrared data communication The PORTI-SW40 has a serial interface for bi-directional data exchange. The infrared port is the right side of the front part. 1. To use the PORTI-SW40’s infrared port by a Computer or a Personal Digital Assistant (PDA) with IR port is required. 2. Position a PDA conforming to the specifications in point not more than 50 centimeter away from the printer’s infrared port. Make sure the two ports are in front of each other with an angle of not more than 15° on the four sides. http://www.woosim.com 18 3.3. Bluetooth 3.3.1. Bluetooth Spec. Category Specification Bluetooth Spec. Bluetooth V1.1 / Class2 (10m) Frequency Range 2.4GHz ISM BAND Data Transmission Rate 57600bps Fixed. Data bit 8 Data bit Fixed. Parity bit No parity Fixed. Stop bit 1 Stop bit Fixed. Notice If the quantity of data what printed at once is more than 20K byte on Bluetooth communication, it would cause the buffer to overflow and the data to get damaged. 3.3.2. Bluetooth Paring Procedure * Notice Ensure that the two devices (PDA and Printer) are turned on, discoverable, and within close range. 1) Tap on the Bluetooth icon in 2) Tap “New” Æ “Connect!” lower-right corner and run Bluetooth manager. http://www.woosim.com 2-19 4. Using the printer 4.1. Control panel X Button - MODE Button MODE Button is for use to change communication mode. (Refer to 2.5. ADJUSTMENT AND SETTING for details about mode conversion) If you want to set to RS-232C Mode, just connect the communication cable to connector of the printer and then the mode will be changed automatically. - FEED Button Press the FEED Button once to advance paper one line. You can also hold down the FEED Button to feed paper continuously. X Panel lamp - Power : This lamp(Green) is on whenever the printer is on. - Error : This lamp(Red) indicated an error such as paper end, or cover open, or mode conversion ,etc. - Battery Power : These lamps(Green) indicated the battery power remaining. The battery gain in quantity and these lamps are on the decrease. If so, you must recharge the battery by using the adapter. http://www.woosim.com 20 4.2. Self test The Self-Test checks whether the printer has any problems. If the printer does not function properly, contact your dealer. For Self-Test, turn on the power while holding down the FEED Button. The Self-Test checks the following : 1) Make sure paper roll has been installed properly. 2) The Self-Test prints the current printer status, which provides the control ROM version and the communication method setting. 3) After printing the current printer status, Self-Test will print a pattern using the builtin character set. 4) The Self-Test automatically ends. The printer is ready to receive data as soon as it complete the Self-Test. http://www.woosim.com 21 4.3. Driver installation The driver installation instruction were written for the printer to be used with the Infrared port and serial port(RS-232C). Make sure that your PC has built-in infrared device(IrDA Ver1.0). Printer driver can download by Internet(http://www.woosim.com). Installing the PORTI-W Printer Driver on Windows 98/ME/2000/XP. 1) You must install new driver after deleting old driver. Delete the old driver Reboot the computer * If there is not any installed driver, you can install new driver immediately. 2) Run the setup.exe Press the “Next” after checking the supported Operating System. (Fig.4.3.1) http://www.woosim.com 22 3) Select printer model to install, and press “Next”. (Fig.4.3.2) 4) Select the port connected to printer, and press “Next” (Fig.4.3.3) http://www.woosim.com 23 5) If the installation has done successfully, press “OK”. (Fig.4.3.4) 4.4. Bit-image download The PORTI-SW40 Printer supports bit image download to the internal Flash ROM. The bit image download require the Porti_Download application and PCX file. Porti_Download Application : The Porti_Download application can download by internet( http://www.woosim.com). PCX file : The picture must be black or white PCX file and the width of picture must be x8 pixel. Refer to Porti_Download manual for details about bit-image download. You can print out the downloaded picture with referred ESC f command. (See sec. 6.6) http://www.woosim.com 24 4. 5. Troubleshooting Check the following points before you make a request for repair. X The power does not turn on. ● AC adapter or battery pack being used? ● AC cable and AC adapter or batter pack is connected. ● AC adapter is connected to the printer correctly? ● Battery pack is fully recharged? X The printer does not print. ● Interface cable is connected correctly? ● Interface cable that meets the Communication Connector specification list on page 15 of the Operator’s Manual being used? ● IrDA transmission status is good? (To close up between Infrared Transmitter / Receiver and the host computer?) ● Transmission conditions of the host computer is correct? (IrDA port is activated and set-up correctly?) ● Paper is not inserted? ● Paper orientation(top/bottom) is correct? http://www.woosim.com 25 X Error Lamp of the power Lamp is blinks. ● Paper end or cover open ? ● Battery is almost exhausted? (Recharge the battery by using the power supply.) X The battery pack is not installed. ● Battery pack correctly oriented? ● Correct battery pack being used? ● Battery pack case damaged? X The battery runs out soon even if recharged. ● Battery been recharged correctly? ● If the battery is recharged correctly, but does not take a long time, it is almost dead. Replace if with a new one. http://www.woosim.com 26 5. Consumble parts 5.1. Recommended paper Type : Thermal Paper Paper width : 113mm Paper thickness : 70±5 Mm Outer diameter : Ø38mm or less Recording side : Outside of roll Cautions : 1. Do not paste the paper to the core, and the roll paper which has near end mark printing on its near end is recommended. 2. Chemicals or oil may change the color of paper, or printed characters may fade. 3. Change of paper color starts from approx. 70 C. Pay attention to heat, humidity and sun light. 4. Color of paper may be changed by being scratched by nail or hard metal, etc. 5.2. Printing position http://www.woosim.com 327
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Encryption : Standard V2.3 (128-bit) User Access : Print, Extract, Print high-res XMP Toolkit : 3.1-702 Producer : Acrobat Distiller 7.0.5 (Windows) Create Date : 2007:07:09 16:36:27+09:00 Modify Date : 2007:11:14 09:26:02+09:00 Metadata Date : 2007:11:14 09:26:02+09:00 Document ID : uuid:47F3FD09EF2DDC11959BAE2A9BF3E4BD Instance ID : uuid:739e7534-a907-4115-a06d-0896db18c9a4 Derived From Instance ID : uuid:352a2377-ae96-45bd-ad55-3409a2c46f44 Derived From Document ID : uuid:580b42eb-e347-44a9-a996-b4bc0920a540 Format : application/pdf Title : Microsoft Word - Operator Manual Porti_SW40.doc Creator :EXIF Metadata provided by EXIF.toolsHas XFA : No Page Count : 27 Author :