WOOSIM SYSTEMS WSP-I450 THERMAL PRINTER User Manual
Woosim System Inc. THERMAL PRINTER
Contents
- 1. User manual
- 2. user manual
User manual
MODEL WSP-i450 (4inch Industrial Printer) Rev. 1.0 WOOSIM SYSTEMS Inc. #501, Daerung Technotown 3th, 448, Gasan-Dong, GeumChun-Ku, Seoul, Korea Tel : +82-2-2107-3700 Fax : +82-2-2107-3707 URL: http://www.woosim.com http://www.woosim.com WSP-i450 Rev. 1.0 Copyright WSP-i450 4inch Industrial printer operator’s manual. Copyright ⓒ2009 by Woosim Systems Inc. All rights reserved. The information contained in this manual is the property of Woosim Systems Inc. and may not be reproduced in whole or in part without the prior written permission of Woosim Systems Inc. Trademark a registered trademark of Woosim Systems Inc. All other trademark are the properties of their respective companies. Caution Some semiconductor devices are easily damaged by static electricity. You should turn the printer “OFF”, before you connect or removed the cable on the rear side, in order to guard the printer against the static electricity. If the printer is damaged by the static electricity, you should turn the printer “OFF” Notice The contents of this manual are subject to change without notice. All specifications are subjected to change without notice http://www.woosim.com WSP-i450 Rev. 1.0 Introduction The WSP-i450 is the ideal solution for Mobile banking system , Retail, point of sales, Credit card Transaction, other traveling and mobile computing etc. The general features of WSP-i450 printer are as follows: X Pocket size 151.5×135.7×63.5mm (MSR : 151.5 X 142.5 X 63.5) X Light weight(550g) for true mobility [standard] X Very silent printing thru direct thermal printing method X High speed (60mm/sec, MAX) X High resolution(203dpi : 8dots/mm). X UART(RS-232C or TTL), Bluetooth Ver2.1 Wireless LAN (IEEE802.11b/g) interface X Support Magnetic Stripe Reader X Support Graphic LCD(128×32dots) with Blue LED Backlight X Intuitive LED’s indicate Power(on/off),Error and Battery status X Support text and graphic printing X Easier paper roll loading by CLAMSHELL design X One touch paper cover X Printer door open & Paper-out sensor X Easier maintenance with self-diagnostic. X In field programming – Update Firmware, Download Fonts and Logos X Compack and easy to carry around. X Water-resistant construction.( IP54 – Certified ) X Microsoft Windows 98 /ME /2000 / XP / VISTA / 7 compatible. X Flow control : Software (XON/XOFF) ※ Hardware flow control not supported in printer. X Free fall: 1 meter onto concrete (option 1.5 meter) X Agency Approvals http://www.woosim.com WSP-i450 Rev. 1.0 Operating Precautions Please follow the precautions below to enjoy and maintain the full performance of the printer. X Using the Printer ● Be careful not to drop or bump the printer on a hard surface. ● Do not install the printer in direct sunlight or such areas. Suitable environment for the use of the printer is as follows: ◆ Operating temperature :-10°C to 50°C ◆ Relative humidity : 0% to 90% (No condensation) ● Do not install the printer near devices that generate strong electromagnetic fields such as a copy machine. ● Do not open the platen cover during printing . ● Do not remove or reinstall the communication cable during printing or transmission. ● Do not touch the connectors of the communication during printing. ● Switch the POWER OFF when not in use. ● Do not use alcohol or other solvent. ● The AC adapter, the battery charger and the battery pack may become warm when in use. This is normal and is not a malfunction. ● When the battery pack is used at low temperature, the length of time the printer can be used may be shortened. X Thermal Paper Handling ● Store the thermal paper in a cool, dry and dark place. ● Do not rub the paper with hard object. ● Do not leave the paper with hard object. ● Do not allow plastic film, erasers, or adhesive tape to touch the paper for long periods. ● Do not stack the thermal paper with diazo copies immediately after copying or wet-type copies. ● Do not use chemical glue. ● Always use the clean thermal paper. http://www.woosim.com WSP-i450 Rev. 1.0 Note This Device has been evaluated to comply with RF exposure requirement for general use limit in portable condition. It is safe to be used in sold condition. http://www.woosim.com WSP-i450 Rev. 1.0 CONTENTS 1. Outline. ...........................................................................................................................................7 1.1. Model classifications. ...............................................................................................................7 1.2. Product Part Number System....................................................................................................7 1.3. Specifications............................................................................................................................8 2. Setting up the printer...................................................................................................................10 2.1. Printer & Accessories .............................................................................................................10 2.2. Printer Features.......................................................................................................................11 2.3. Replacing paper roll................................................................................................................13 2.4. Power supply ..........................................................................................................................14 2.4.1. Specified power supply. ...................................................................................................14 2.4.2. Installing the battery and the belt strap ............................................................................14 2.4.3. Recharging the battery pack.............................................................................................15 2.5. Set operation mode. ................................................................................................................16 3. Interface........................................................................................................................................22 3.1. UART(RS-232C or TTL)........................................................................................................22 3.2. Bluetooth ................................................................................................................................23 3.3. Wireless LAN .........................................................................................................................23 4. Smart Card Module.....................................................................................................................24 4.1. General Spec...........................................................................................................................24 4.2. Communication Protocol Sequence........................................................................................25 4.2.1. Regular Operation............................................................................................................25 4.2.2. Irregular Operation (Communication Error)....................................................................25 5. Using the printer. .........................................................................................................................26 5.1. Control panel. .........................................................................................................................26 5.2. The self test.............................................................................................................................27 6. Consumable Parts........................................................................................................................28 6.1. Recommended paper...............................................................................................................28 5.2. Printing position......................................................................................................................28 http://www.woosim.com WSP-i450 Rev. 1.0 1. Outline. 1.1. Model classifications. WSP-i450 Model Interface None: UART/Bluetooth A2 : UART/IrDA Power None : DC 8.4V 1.2. Product Part Number System. Model name 2. Porti-SC30 Interface Spec. Wired S40 SC30 W25 Example) 1. Porti-S40 Serial/Bluetooth Wireless RS-232C Bluetooth TTL IrDA USB None RS-485 Parallel None Part No. ⇒ S40/A1 Bluetooth Only Part No. ⇒ SC30/Z1 http://www.woosim.com WSP-i450 Rev. 1.0 1.3. Specifications. Item Specifications Print method Direct thermal line printing Characters per line Eng : 92cpl (MAX) Character size Eng. : 9×24dots, 12×24dots Optional Characters Simplified/Traditional Chinese, Arabic, Cyrillic, Russian, Tukish, Greek, Japanese, Persian, Latin9 and Others upon request. Resolution 203dpi, 8 dots/mm Print width 4-inch ( 104mm, 832dots) Print speed 60mm / sec (MAX) Dimension Kor. : 16×24dots, [24×24dots] 151.5× 135.7 × 63.5 mm (MSR : 151.5 X 142.5 X 63.5mm) 550g (Including battery & roll paper) [standard] Weight 556g (Including battery & roll paper) [MSR] Interface UART(RS-232C or TTL), Bluetooth Ver 2.1 + EDR Wireless LAN interface(IEEE802.11b/g) Paper roll Thermal roll paper ( 113mm wide, 50ø) Barcodes 1-dimension : Code128, Code39, I2/5, Code93 UPC, EAN, KAN, JAN, CODABAR 2-dimension : PDF417, QR Code, DATA Matrix Black mark Support black mark detection H/W Spec. MCU : 32bits RISC, FLASH : 4M bytes, RAM : 8M bytes Receive buffer size 1M bytes MSR ISO 7810 / 7811 / 7812 1&2&3 Track Reading ISO 7816 Compliant (EMV level 1 Certified) / Smart Card Reader T=0, T=1 support / 1 SAM (Security Application Module) LCD 128×32 Dots FSTN (Blue LED Backlight) Battery Rechargeable 7.4V DC, 2,200mAh (Li-ion) Battery duration 1 hour continuous printing (Continue…) http://www.woosim.com WSP-i450 Rev. 1.0 Item Specifications Input (100~250V AC, 50~60Hz) Battery charger Output(8.4VDC/0.8A), 4hours full charge time Temperature Environment conditions Humidity MCBF(Mean Cycle Between Failure) Mechanical Head -10°C ~ 50°C (operating) -10°C ~ 70°C (storage) 30% - 80% (operating) 0% - 95% (storage) 37,000,000 lines Approximately 50 Km < Table 1 > http://www.woosim.com WSP-i450 Rev. 1.0 2. Setting up the printer. 2.1. Printer & Accessories Your printer box should include these items. If any items are damaged or missing, please contact your dealer for assistance. Thermal roll paper Battery pack WSP–i450 Battery charger adaptor Communication cable SAM Connector Shoulder band Smart Card http://www.woosim.com MSR 10 WSP-i450 Rev. 1.0 2.2. Printer Features ▶ Part Name http://www.woosim.com 11 WSP-i450 Rev. 1.0 ▶ Dimensions http://www.woosim.com 12 WSP-i450 Rev. 1.0 2.3. Replacing paper roll. Note : Be sure to use paper rolls that meet the specifications. Do not use paper rolls that have the paper glued to the core because the printer can not detect the paper end correctly. 1. Make sure that the printer is not receiving data; otherwise, data may be lost. 2. Open the paper cover by placing your fingers under the paper cover lock and pull a paper cover lock open. 3. Insert a new paper roll as shown. 4. Tear the excess paper off using the edge of paper door as a tear bar. http://www.woosim.com 13 WSP-i450 Rev. 1.0 2.4. Power supply 2.4.1. Specified power supply. The following specification is requested for Power supply. Battery Charger : DC 8.4V/0.8A Avoid using power supply which its power capacity of power current is extremely high. 2.4.2. Installing the battery and the belt strap NOTE : ● Before installing or removing the battery pack, ensure the printer is OFF. ● If the printer is not used for long period of time, remove the battery pack from the printer. ** BATTERY ** To install battery pack, proceed as follows: - Insert the Battery pack in the direction of the arrow. Reverse the order to remove the battery pack. ** BELT STRAP ** http://www.woosim.com 14 WSP-i450 Rev. 1.0 2.4.3. Recharging the battery pack For recharging the battery pack, install the battery pack in the printer. Insert the Battery Charger to the charge connector of the printer. NOTE : ● While charging the printer, turn off the printer power. ● Do not remove the battery during charging. ● The battery is consumable parts and when purchasing, compared to the use hour is gradually decreases. (Warranty 6 month) ● If the printer is not used for a long time, unplug the power cord from the printer and outlet. ● The recharging time depends on the voltage level and ambient temperature of the battery. Normally, if takes about 4 to 5 hours to recharge a battery pack. ● You must use only the supplied adapter. ● Red Lamp : charging the battery. Green Lamp: charging is finished. http://www.woosim.com 15 WSP-i450 Rev. 1.0 2.5. Set operation mode. Change the mode and option using the mode Code. z MODE button : changing Printer MODE status. (Error Lamp) z FEED button : changing OPTION status. [Example] The defaults of the printer are : UART / 9600 bps / 8 data bit / No parity /1 stop bit / Density low / Quality low / Mark use / Sensor low / Power down 5 minute If a user wants to modify the defaults with Bluetooth / 57,600 bps / 7 data bit / Odd parity /2 stop bit / Density high / Quality high / Mark no use / Sensor medium1 / Power down no use X Press MODE Button and FEED button during the Error Lamp flickers 5 times. → You will see present COMMUNICATION mode in the LCD. → Press the MODE Button twice. And then, interface mode has set to Bluetooth mode. X When you press FEED button once. → You will see present BAUD RATE mode in the LCD. → Press MODE Button 3 times. And then, baudrate has set to 57,600 bps. X When you press FEED button once. → You will see present DATA BIT mode in the LCD. → Press MODE Button once. And then Data Bit has set to 7 data bit. X When you press FEED button once. → You will see present PARITY mode in the LCD. → Press MODE Button once. And then the Parity bit has set to Odd parity bit. X When you press FEED button once. → You will see present STOP BIT mode in the LCD. → Press MODE Button once. And then the density has set to 2 stop bit. http://www.woosim.com 16 WSP-i450 Rev. 1.0 X When you press FEED button once. → You will see present DENSITY mode in the LCD. → Press MODE Button twice. And then the density has set to Density high. X When you press FEED button once. → You will see present Quality mode in the LCD. → Press MODE Button once. And then the quality has set to Quality high. X When you press FEED button once. → You will see present MARK mode in the LCD. → Press MODE Button once. And then the mark has set to Mark no use. X When you press FEED button once. → You will see present SENSOR mode in the LCD. → Press MODE Button once. And then the sensor has set to Sensor medium1. X When you press FEED button once. → You will see present PWDN mode in the LCD. → Press MODE Button once. And then the Power down has set to Power down no use. If all the mode have set, press the MODE Button and the FEED Button at the same time after then release the buttons at the same time. The printer will print out the mode status which has modified. (Bluetooth / 57600 bps / 7 data bit / Odd parity / 2 stop bit / Density high / Quality high Mark no use / Sensor medium1 / Power down no use) If the status is not correct, please try it again according to the procedure. http://www.woosim.com 17 WSP-i450 Rev. 1.0 * Bluetooth Version Communication Port Baud Rate Data Bit Parity Bit Stop Bit Density Quality POWER Lamp ERROR Lamp (Green) (Red) Option UART(RS-232C) Protocol UART(RS-232C) Bluetooth Protocol Bluetooth 9600 bps 19200 bps 38400 bps 57600 bps 115200 bps 7 Data bit 8 Data bit No Parity Odd Parity Even Parity 1 Stop bit 2 Stop bit Density Low Density Medium Density High Low High (Continue…) http://www.woosim.com 18 WSP-i450 Rev. 1.0 Mark Sensor Power Down POWER Lamp ERROR Lamp (Green) (Red) 10 Option No use Use Low Medium1 Medium2 High No use 1 minute 2 minute 3 minute 4 minute 5 minute < Table 2 > http://www.woosim.com 19 WSP-i450 Rev. 1.0 * WLAN Version Communication Port Baud Rate Data Bit Parity Bit Stop Bit Density Quality POWER Lamp ERROR Lamp (Green) (Red) Option UART(RS-232C) Protocol UART(RS-232C) WLAN Protocol WLAN 9600 bps 19200 bps 38400 bps 57600 bps 115200 bps 7 Data bit 8 Data bit No Parity Odd Parity Even Parity 1 Stop bit 2 Stop bit Density Low Density Medium Density High Low High (Continue…) http://www.woosim.com 20 WSP-i450 Rev. 1.0 Mark Sensor Power Down POWER Lamp ERROR Lamp (Green) (Red) 10 Option No use Use Low Medium1 Medium2 High No use 1 minute 2 minute 3 minute 4 minute 5 minute < Table 3 > http://www.woosim.com 21 WSP-i450 Rev. 1.0 3. Interface. 3.1. UART(RS-232C or TTL) Pin No. Name Direction Function TxD Output Transmit Data RxD Input Receive Data CD NC. GND Cable Detector Ground The WSP-i450 printer has a UART(RS-232C or TTL) interface and is connected by means of a 5 pin mini USB socket. In the following table, the signals present on the Mini- USB socket are listed: NOTE : ● When data receiving, when it removes the communication cable, it loses a data. http://www.woosim.com 22 WSP-i450 Rev. 1.0 3.2. Bluetooth Category Specification Bluetooth Spec. Bluetooth Ver2.1 / Class2 (10m) Frequency Range 2.4GHz ISM BAND (2402 ~ 2480 MHz) RF Power Below 10 dBm Modulation method GFSK Oscillation method PLL Data Transmission Rate 57600bps Fixed. Data bit 8 Data bit Fixed. Parity bit No parity Fixed. Stop bit 1 Stop bit Fixed. 3.3. Wireless LAN Category Specification Interface Network RF Power Below 10 dBm Modulation method CCK, OFDM Oscillation method PLL Protocol TCP, UDP, IP, ICMP, ARP, DHCP, PPPoE IEEE802.11b/g DNS lookup, DDNS(Dynamic DNS), WEP Communication Mode T2S TCP Server Mode COD TCP Client Mode ATC TCP Server / Client (AT command emulation) U2S UDP http://www.woosim.com 23 WSP-i450 Rev. 1.0 4. Smart Card Module 4.1. General Spec. X Contact Smart Card Reader Module for ISO/IEC-7816 X Support Asynchronous Protocol T=0,T=1 X Smart Card Connection Short Circuit Current Limitation 6KV ESD Protection on whole Smart Card Interface Connector : Friction Type with Smart Card presence detection X 1 SAM (Security Application Module) X EMV Level 1 Certified http://www.woosim.com 24 WSP-i450 Rev. 1.0 4.2. Communication Protocol Sequence 4.2.1. Regular Operation Host Command Module Execution Response 4.2.2. Irregular Operation (Communication Error) 500ms timeout Host Command Command Module Host Command Command is Command Executio Command Error Module CheckSumEr http://www.woosim.com Executio 25 WSP-i450 Rev. 1.0 5. Using the printer. 5.1. Control panel. X Button - FEED Button : When the printer is on, paper can be feed manually by pressing and holding the FEED button for more than one second. - POWER Button : When of 5 or more seconds presses and power comes to on or off. After pressing the POWER and the FEED button simultaneously, if the ERROR lamp 5 turn signals POWER button is converted with MODE functions. MODE functions are for use to change communication mode. (Refer to 2.5. Set operation mode for details about mode conversion) X Panel lamp -POWER (Green) : Printer is ON and ready to receive data. -ERROR (Red) : Indicated a fault condition or a printer error. (i.e : no paper, paper cover opened. etc.) http://www.woosim.com 26 WSP-i450 Rev. 1.0 5.2. The self test. The self test procedure will check most of the printer functions. For self test, turn on the power while holding down the FEED Button. The Self-Test checks the following : 1) Make sure paper roll has been installed properly. 2) The Self-Test prints the current printer status, which provides the control ROM version and the communication method setting. 3) After printing the current printer status, Self-Test will print a pattern using the built-in character set. 4) The Self-Test automatically ends. The printer is ready to receive data as soon as it completed the self test. http://www.woosim.com 27 WSP-i450 Rev. 1.0 6. Consumable Parts. 6.1. Recommended paper. Type : Thermal Paper Paper width : 104mm Paper thickness : 60±5㎛ Outer diameter : Ø50mm or less Recording side : Outside of roll Cautions 1. Do not paste the paper to the core. And the roll paper which has Near end mark printing on its near end is recommended. 2. Chemicals or oil may change the color of paper, or printed Characters may fade. 3. Change of paper color starts from approx 70 ℃. Pay attention to heat, humidity and sun light. 4. Color of paper may be changed by being scratched by nail or hard metal, etc 5.2. Printing position. http://www.woosim.com 28
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Encryption : Standard V4.4 (128-bit) User Access : Print, Extract, Print high-res Author : Administrator Create Date : 2010:11:10 18:08:58+09:00 Modify Date : 2010:11:11 10:36:19+09:00 Has XFA : No XMP Toolkit : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04 Producer : Acrobat Distiller 7.0 (Windows) Creator Tool : PScript5.dll Version 5.2 Metadata Date : 2010:11:11 10:36:19+09:00 Format : application/pdf Creator : Administrator Title : Microsoft Word - Appendix-G User Manual_WSP_i450.doc Document ID : uuid:fc4c4bf0-495f-4e5f-a3b2-3ab86272565f Instance ID : uuid:f7069498-ec21-4729-8bec-9975b8843292 Page Count : 28EXIF Metadata provided by EXIF.tools