Wayne Fueling Systems WAYNETRACII User Manual correction for installation manual section one

Wayne Fueling Systems LLC correction for installation manual section one

Contents

correction for installation manual section one

1-1
July 2000 Part No. 920472 Rev. C
Section 1
Before You Start
1.1 Introduction
This manual explains how to install the EasyPAY™ retrofit kit in selected models of Wayne™ Vista 90
series dispensers. This includes all Models V390, V395, V490 and V590 except those with 2/ and 3/
prefix numbers.
By following this instruction manual in the sequences presented, you will be assured of a successful in-
stall. For best results, perform the steps in the sequence given for the particular kit or kits that are being
installed.
Important: These retrofit kits require installation of several wiring and hardware assemblies. Any
installation or modification must comply with the requirements of the National Electrical
Code (NFPA 70), the Automotive and Marine Service Station Code (NFPA 30A) and any
other applicable codes.
Refer to the information in Table 1-1 for identification of the EasyPAY™ retrofit kits.
1-2
Part No. 920472 Rev. C July 2000
Section 1: Before You Start
Important: You must wear a static wrist strap, part number 916962 or equivalent, securely attached
to an earth ground, when handling any circuit board, electronic component or assembly,
or when reaching into the site controller or dispenser computer enclosure. Do not use
power tools.
No Modifications:Modifications to this device shall not be made without the written consent of
Wayne Division, Dresser Equipment Group. Unauthorized modifications may void the authority
granted under Federal Communications Commission Rules permitting the operation of this device.
1.2 Unpacking and Inspection
Complete the following steps:
1. Before opening any cartons, count the number of cartons and verify the carton count against the
supplied packing list.
2. Inspect the cartons for damage made during transit.
3. File claim information with the carrier on the bill of lading.
4. Retain cartons suspected of damage for future claim purposes.
Caution: You must wear an anti-static wrist strap, part number 916962 when removing electronic
components from static packages. Attach the wrist strap securely to an earth grounding point to prevent
possible damage from static electricity.
5. Remove all equipment from the shipping cartons and carefully inspect for visible damage.
Note: Any damage should be brought to the attention of the carrier and claims made immediately.
Return all equipment to the respective cartons for protection until actual installation is made. Save all
cartons until it is certain that return shipments are not required.
6. Check supplied graphics (such as ad panel and dial face graphics) prior to start of installation.
1.3 Returning Damaged Components
Parts or components returned to the factory under warranty or for repair are subject to damage if not pack-
aged properly. Complete the following steps to return parts or components to the factory.
1. Place electronic components in an anti-static bag and in the original shipping cartons for return
shipment to the factory.
Note: If original shipping cartons are not available use a sturdy cardboard container and suitable
packing materials such as anti-static polyethylene foam or bubble pack, to ensure the component is
firmly packed.
2. Include a Return Parts Tag with the defective component describing the particular problem with the
part.
Table 1-1 EasyPAY™ Retrofit Kits for Vista
Part Number Description
887122-001 EasyPAY Retrofit Kit, Vista DS
Section 1: Before You Start
1-3
July 2000 Part No. 920472 Rev. C
3. Make sure adequate insurance is provided when returning parts to the factory.
WARNING: If the parts or components arrive at our factory in a damaged condition and it is
determined that the damage is a direct result of inadequate or improper packaging, the damage will not
be covered under the original warranty and the customer or distributor will be held responsible for the
cost of repairs necessary to correct or replace the damaged parts.
1.4 Required Tools
Refer to Table 1-2 for a list of tools required to install the EasyPAY retrofit kit.
1.5 Power Ratings
The EasyPAY installation does not change the existing dispenser power rating.
Table 1-2 Required Tools
Quantity Description
1Phillips Screwdriver (medium and small)
1Slotted Screwdriver (medium and small)
11/4 inch Nut Driver
13/8 inch Socket Wrench
1Diagonal Cutters
1Anti-static Wrist Strap
1Wire Stripper
1Needle Nose Pliers
1Pin Pusher
1-4
Part No. 920472 Rev. C July 2000
Section 1: Before You Start

Navigation menu