Westhold TX3-9V Automobile Race Management Transmitter User Manual TX3 9V
Westhold Corporation Automobile Race Management Transmitter TX3 9V
Westhold >
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 78568 |
| Application ID | OtWKyN0uNSxwW1GkaaYy9Q== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 1.32kB (16442 bits) |
| Date Submitted | 1999-12-28 00:00:00 |
| Date Available | 2000-02-29 00:00:00 |
| Creation Date | 1999-12-28 08:38:29 |
| Producing Software | Acrobat PDFWriter 4.0 for Windows NT |
| Document Lastmod | 0000-00-00 00:00:00 |
| Document Title | User Manual TX3-9V |
| Document Creator | Microsoft Word - User Manual TX3-9V |
| Document Author: | Administrator |
FCC ID: NKBTX3-9V Westhold Corporation TX3-9V Transmitter User Manual (Draft) Overview Thank you for selecting the Westhold TX3-9V transmitter. It is part of a sophisticated electronic timing and scoring system, the RMS-3. The lightweight and compact TX3-9V device operates on a standard 9 volt alkaline battery. It is easy to install, operate and maintain. Operation Directions Phillips Screw Battery Compartment Lid TX3-9V Low Battery LED(Red) Normal Operation LED(Green) TX3-9V Illustration The TX3-9V operates on a standard 9 volt alkaline battery. The battery can be inserted by first removing the small Phillips head screw and removing the battery compartment lid. Slide the battery into the compartment with the terminals of the battery coming in contact with the spring contacts as shown in the diagram below: Spring Contacts It does not matter which battery terminal comes in contact with which spring contact. The TX3-9V will function with the battery in either orientation. Once the battery has been placed in the compartment, check to see that the green LED indicator light flashes. If the red LED light flashes, it indicates the battery is weak and therefore should be replaced. If both LED lights come on, remove the battery and reinstall the battery as per the instructions above. Place the battery lid back on the TX3-9V and screw down the lid. A fresh 9 volt battery will power the TX3-9V for 72+ hours. FCC ID: NKBTX3-9V Installation Fasten the TX3-9V on the car or motorcycle using pop rivets or some other suitable fastening. Be sure to place all transmitters in the same location on each vehicle. The best possible orientation of the transmitter is shown below with the longest edge of the transmitter parallel to the Start/Finish line where the loop antenna is located. Direction of Travel Maintenance The TX3-9V requires minimal maintenance. Cleaning the spring battery contacts can be done with a damp cloth or cotton swab. The external plastic may be cleaned with a damp cloth. Do not use solvents to clean either the plastic or the battery contacts. Specifications Specification Dimensions Weight Temp Range Battery Life Operational Indicator Low Battery Indicator Humidity Approx. 3.25” x 2” x 0.75”(≈8x5x2cm) Approx. 4oz(100 grams) 32-122°F (0-50°C) 72 Hours Nominal(100 Typical) LED LED 100% Relative FCC Notice FEDERAL COMMUNICATIONS COMMISSION RADIO AND TELEVISION INTERFERENCE STATEMENT Changes or modifications not expressly approved by Westhold Corporation could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received including interference that may cause undesired operation. FCC ID: NKBTX3-9V
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Page Count : 2 Creator : Microsoft Word - User Manual TX3-9V Create Date : 1999:12:28 08:38:29 Title : User Manual TX3-9V Author : Administrator Producer : Acrobat PDFWriter 4.0 for Windows NTEXIF Metadata provided by EXIF.tools