Whirlpool CA2762XYW0 User Manual COMMERCIAL AUTOMATIC WASHER Manuals And Guides 1101258L

User Manual: Whirlpool CA2762XYW0 CA2762XYW0 WHIRLPOOL COMMERCIAL AUTOMATIC WASHER - Manuals and Guides View the owners manual for your WHIRLPOOL COMMERCIAL AUTOMATIC WASHER #CA2762XYW0. Home:Laundry & Garment Care Parts:Whirlpool Parts:Whirlpool COMMERCIAL AUTOMATIC WASHER Manual

Open the PDF directly: View PDF PDF.
Page Count: 8

DownloadWhirlpool CA2762XYW0 User Manual  COMMERCIAL AUTOMATIC WASHER - Manuals And Guides 1101258L
Open PDF In BrowserView PDF
IMPORTANT:
Read and save
these instructions
IMPORTANT:
Installer: Leave Installation
with the owner.

Part No, 3360618

COMMERCIAL
IC
120-volt, 60-Hz Models

Instructions

Owner: Keep Installation Instructions for
future reference.
Save Installation Instructions for local
electrical inspector's use.
www.whirlpool.com

@

®

COMMERCIAL
LAUNDRY
PRODUCTS

Before

you start._

Your safety and the safety of
others is very important.
We have provided many important
safety messages in this manual and on
your appliance. Always read and obey all
safety messages.
This is the safety alert
symbol. This symbol alerts
__
you to hazards that can kill or
hurt you and others. All safety
messages will be preceded by the safety
alert symbol and the word "DANGER" or
"WARNING". These words mean:
Check location where washer
will be installed, Proper
installation is your responsibility,
Make sure you have everything
necessary for correct installation,

You wiii be killed or seriouslyinjured if
you don't follow instructions.

Do Not store or operate washer below
32°F (some water may remain in
washer).
See Use& Care Guide for
"Winterizing" information.

You can be killed or seriously injured if
you don't follow instructions.
All safety messages will identify the hazard,
tell you how to reducethe chance of injury,
and tell you what can happen if the
instructions are not followed.
Single washer
installations require 12
inch minimum risers to
provide an air cushion
and prevent noise and
damage
to valves,

Grounded
electrical
outlet
is required, See
Electrical
requirements,

Hot and cold wafer faucets must be
within 4 feet of the back of the washer
and provide water pressure ] 0-1 O0 PSI,
A pressure reduction valve should be
used in the supply line where inlet
pressure entering the building
exceeds ] O0 PSIto prevent damage
to the washer mixing valve,

Untape and
open washer
lid, Remove
packages
and hoses
from washer,

No. T20 Torx

Level floor:
Maximum
slope under
washer-] inch,

screws

On coin-operated
washers, front
access to the pump area is available
by removing the two, No, T20 Torx
screws and then removing the front
panel, Non-coin-operated
washers do
not have a removable
front panel,
The cabinet and top assembly must
be removed by removing clips under
console on the non-coin-operated
washer,
PAGE 2

Non-coin-operated
washers are
equipped
with a console, push to start
timer, selector switches and indicator
lights (net pictured),
A floor drain should be provided
under the bulkhead,
Prefabricated
bulkheads with electrical outlets,
water supply lines and drain facilities
should be used only where local
codes permit,

Wafer heater: Set to deliver
140°F to 160°F water to the
washer,

Standpipe drain system: Needs a twoinch minimum carry-away capacity
of 17 gallons per minute, Top of
standpipe must be at least 34 inches
high and no higher than 72 inches
from bottom of washer,
Support: Floor must be sturdy enough
to support loaded washer weight of
315 pounds,
Important: Observe all governing
codes and ordinances.

Tools needed for
installation:
level

Electrical

requirements

)liers

3-prong
ground

3-prong groundtype outlet
------_--J]lllllt_l

plug
power supply
cord

Figure ]
Electrical Shock Hazard

Cii

Plug into a grounded 3-prong outlet.

Now start...

Do not remove

With washer

ground prong.

in laundry

area.

Do not use an adapter.
Do not use an extension cord.
fiat-blade
screwdriver

Failure to follow these instructions
can result in death, fire, or electrical
shock.

utility
knife

If codes permit and a separate
wire is used, it is recommended
qualified electrician determine
the ground path is adequate.

ground
that a
that

Excessive Weight Hazard
Use two or more people to move
and install washer.
Failure to do so can result in back
or other injury.

Do Not ground to a gas pipe.
Check with a qualified electrician if
you are not sure the washer is properly
grounded.
Do Not have a fuse in the neutral or
ground circuit.

Parts supplied for
installation:

A 120-volt, 60-Hz, AC-only, 15- or
20-ampere
fused electrical supply is
required, (Time-delay fuse or circuit
breaker is recommended.)
It is
recommended
that a separate circuit
serving only this appliance be provided,

shipping

Recommended
ground method

Remove parts from packages.
that all parts were included,

I
2
4
2
I

hose clamp
inlet hoses
flat water hose washers
front-leveling legs with nuts
drain hose

Check

For your personal safety, this appliance
must be grounded. This appliance is
equipped with a power supply cord
having 3-prong ground plug. To
minimize possible shock hazard, the
cord must be plugged into a mating
3-prong ground-type
outlet, grounded
in accordance
with local codes and
ordinances. See Figure 1. If a mating
outlet is not available, it is the personal
responsibility and obligation of the
customer to have a properly grounded
3-prong outlet installed by a qualified
electrician.
WARNING - Improper connection
of
the equipment-grounding
conductor
can result in a risk of electric shock.
Check with a qualified electrician
or
serviceman
if you are in doubt as to
whether the appliance
is properly
grounded,
Do not modify the plug
provided with the appliance
- if it will
not fit the outlet, have a proper outlet
installed by a qualified electrician.

covers
[] Remove
shipping tape
strap, that
Pull to
completely
remove the shipping
strap with 2 cotterpins from the inside
of the washer,

Pull firmly to remove the
end of shipping strap from
the back of the washer, The shipping
strap plug must be completely
removed from the washer for the
self-leveling legs to be released,
Save the shipping
Step 6.

PAGE 3

strap for use in

Usenew

hoses and washers that
came with your Whirlpool washer.

coupling

g== Stack two corner posts on top of
each other. Tilt washer backwards
and insert corner posts 3 inches in
from one side of washer as shown.
Repeat with other corner posts on
other side of washer,

washer

= Insert a flatwasher

into each

end of the inlet hoses. Check
washers are firmly seated in
couplings.

that

Inlets are plastic.
Do Not strip or
crossthread.

==Place hose clamp over washer
drain connector.
Push drain hose onto
washer connector,
use pliers to open
clamp and slide clamp over drain
hose, Check for good fit,

I/2"

base

nut

hose to bottom inlet
valve opening first. Then second hose
to top inlet. Tighten couplings by
hand; then use pliers to make an
additional
two-thirds turn.
Slide washer onto cardboard
or
hardboard
before moving across
floor,

==Measure and mark
approximately
] 6 inches
plug end of the shipping
this shipping strap at this
Check that hose is not
twisted or kinked and
is securely in place.

a point
from the
strap. Cut
point.

0
==Use legs and nuts from parts
package.
Screw nut down to within
]/2 inch of base,

11.

Put "hook" end of
drain hose into
standpipe.
Tightly
wrap the shipping
strap around the
standpipe.
Push plug
into the nearest hole
in the shipping strap,

Insert legs into
correct holes at
front corner of washer
until nuts touch washer. Do Not
tighten nuts until Step 14,

backward

and

remove corner posts. Gently
washer to floor,

2

==Tiltwasher

lower

Move washer to its permanent
location. Remove cardboard or
hardboard from under washer.

==Move washer

close to final

position. Put "hook" end of drain hose
into standpipe.
Estimate length of
drain hose needed when washer is in
final position. Hose must be cut
exactly to length so "hook" end is
held tightly over edge of standpipe.
If
drain hose is too long, cut straight end
of hose, (Do Not cut "hook" shaped
end of drain hose.)
DO NOT FORCE EXCESS LENGTH OF
DRAIN HOSE DOWN THE STANDPIPE.
THISCOULD CAUSE SIPHONING. See
Step 6.

PAGE4

I

==Before attaching

water

inlet

hoses, run water through both faucets
into a bucket, This will get rid of
particles in water lines that might clog
hoses. Mark which is the hot water
faucet,

bottom hose (inlet
marked "H') to hot water faucet.
Attach top hose (inlet marked "C') to
cold water faucet. Tighten coupling
to faucet by hand; then use pliers to
make final two-thirds turn.

JA

13
==Tilt washer forward raising
back legs 1 inch off of floor. To adjust
rear self-leveling legs, gently lower
washer to floor, Check levelness of
the washer by placing a carpenter's
level on top of the washer, first side to
side; then front to back,

\!/

17.

CORRECT ELECTRICAL SUPPLYAND
RECOMMENDED GROUNDING
METHOD.
REQUIREMENTS. BE SUREYOU HAVE

14.

if washer is not level, adjust
the front legs up or down. Make final
check with level,

console to manually operate the
timer. Remove the rear of the
console to manually operate the
timer of non-coin-operated
washers.
Start the washer and allow it to
complete
the Normal cycle,
Rotate
counterclockwise
only. --

timer
"off" -position

When washer is level, use wrench
to turn nuts on front legs up tightly
against washer base. If nuts are not
tight against washer base, the washer
may vibrate.

timer-front

Check that all parts are now installed,
See parts list, Page 3, If there is an
extra part, go back through steps to
see which step was skipped,

9

mTurn on water

faucets

and

check for leaks. Tighten couplings if
there is leaking. Do Not overtighten;
this could cause damage
to faucets.

15. On

coin-operated
washers,
remove the service door of the meter
case. Lift the service door up at the
back and remove. Carefully insert coin
slide with the coin slide extension
attached
into front opening and
secure with the 3/16" mounting bolt
from inside the meter case. The coin
slide may need to be partially pushed
in to insert mechanism in the front
opening. Replace meter case top and
service door, Insert coin vault with lock
and key,

0

0

conversion

6 =putthe

bar

\-

coin vault with lock

and key in the meter case opening. A
larger-capacity
coin vault can be
installed. Use a knife to carefully
remove the paint along the seam at
the bottom of the conversion bar, Use
a blade screwdriver and a hammer
to lightly tap along the seam area.
Raise the conversion bar up to the
notches in the sides of the vault
opening. Remove the conversion bar
and drawer guide, Install new guide
(found in parts bag) and the larger
coin vault,
PAGE 5

view

• Coin-operated
timers can be
started by turning the clutch
assembly counterclockwise
until the
washer starts to fill with water,

cycle
,_%o
"_
information _ %._/÷_I

Pull to start
Push to stop
top

/_ _

_
0

- e-_\

I

__

Timer-rearview
• Non-coin-operated
timer cycle
information
is link stamped on the
rear of the timer, Push in on the
lever attached
to the timer shaft.
Reset lever to the Normal cycle
position, then pull out on lever to
start washer,

0mCheck
that you have all of
your tools. Check that the shipping
strap with 2 cotterpins and plug was
removed from the back of the washer
and used to secure the drain hose,
If entire strap is not removed,
may vibrate and be noisy.

1.

Untape power
and plug into grounded

2.

washer

supply cord
outlet.

Check the wash cycle time,
Both coin-operated
and non-coinoperated
washers have timers with a
9-minute wash in the Normal cycle.
Remove the meter case top of coinoperated
washers to manually start
the timer, Remove the rear of the

timer clutch adjustment

3.

screw

If the washer fails to start or

does not give the proper washer
cycle time, the clutch assembly of the
coin-operated
timer can be adjusted,
Remove the timer from the meter
case. Adjust the clutch assembly
screw clockwise if the washer does
not start after the coin slide
mechanism
has been fully actuated
in or out. Adjust the clutch assembly
screw counterclockwise
if the washer
segment of the Normal cycle was less
than 9 minutes.

Owner options (coinoperated models)
CAUTION: Disconnect power cord.
1. For WARM RINSE and WATER SAVER:
• Remove screws from each end
of the console bottom.
• Pull the console bottom
forward; lift and tilt it back,
a, WARM RINSE
• Connect

Typical full load sizes.
Load
Type
Mixed
Load

3
4
6
8
2
2
8

Permanent
Press

2 double or
1 king size sheet
1 tablecloth
1 dress
1 blouse
2 slacks
3 shirts
2 pillowcases

J1 to J2

b, SAVE WATER
• Pull out tab on water-level
2. If use of
and key
in lower
can be

switch.

a larger coin vault, lock
is desired, conversion bar
portion of coin vault area
removed,

3. If additional security is needed, top
and cabinet can be locked to
washer back panel by using a
"screw type" lock and key in space
provided in top panel under
console. The "screw type" lock and
key are available from usual
industry sources.

Check list for washer
operation
Check the following if the washer
not operating
properly:
1. Power supply cord is plugged
2. Circuit breaker
blown,

is not tripped

3. Timer has been
of a cycle,

advanced

4. Water faucets

Loading
Suggestion
double sheets
pillowcases
pair shorts
T-shirts
shirts
blouses
handkerchiefs

Operating Tips

Load

Loading
Suggestion

Type
Heavy
work
clothes

3
3
1
4
1

pair pants
shirts
coverall
pair jeans
overall

Knits

3
4
6
4
4

blouses
slacks
shirts
tops
dresses

Moving the washer to
a new location...

is
Wedge blanket
between tub ring
and cabinet top.

in,
or fuse

Remove front legs.

to start
Fire Hazard

are turned

on,

5. Inlet and drain hoses are not kinked,
6. Washer lid is closed,
7. Inlet valve is frozen if not protected
from the weather,
8. Suds level, Excess suds will slow the
spin and cause poor rinsing,
Operate the washer through a
complete
cycle with no detergent,
Use less detergent
or a controlled
suds type detergent
in future loads,

Never place items in the washer
that are dampened with gasoline or
other flammable fluids.
No washer can completely
oil.

Tape rear
logs in "up"
position,

Tape 2
sides,

remove

Do not dry anything that has ever
had any type of oil on it (including
cooking oils).
Doing so can result in death,
explosion, or fire.
It is recommended
that fiberglass
items not be washed in coinoperated
washers, If these items are
washed in the washer, run the washer
through a complete
cycle to rinse
any residue away that might be left in
the washer,

Note: Do Not
place blanket
in this area
(switch).

• Remove the front legs from the
base of the washer,
• Place both rear leveling legs in the
upper position and tape securely,
• Apply tape to the side and bottom
of the cabinet near the rear,
• Open washer lid, wedge a blanket
between the tub ring and the
cabinet top restricting the tub
movement,
• Handle washer carefully, Do Not
drop washer while using hand truck.

PAGE 6

7"

Power supply cord

Cold
II

1-1/2"

Hot

Water
Inlets

Drain hose
connector
35"

PAGE 7

CORPORA[ION

Part No, 3360618
©1999 Whirlpool

Corporation

Prepared

by Whirlpool

Corporation,

Benton Harbor,

Michigan

49022

Printed in U,S,A,



Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Page Count                      : 8
Page Layout                     : SinglePage
Page Mode                       : UseNone
Producer                        : Goby Monitor Application version 4, 0, 0, 13
Create Date                     : Fri Jan 14 04:11:30 2011
Author                          : 
Title                           : 
Subject                         : 
EXIF Metadata provided by EXIF.tools

Navigation menu