Willis Electric ZW97 Outdoor Smart Plug User Manual

Willis Electric Co., Ltd. Outdoor Smart Plug

User Manual

ZW97 Z-Wave 2-Channel OutDoor Smart PlugIntroduction: Thank you for choosing the ZW97 Z-Wave control product.ZW97 enabled product allows users to remotely control lighting, home appliance, and make home control easy with low installation and maintenance costs. You may begin with a few Z-Wave enabled devices as well as some of our products to build up acomplete home automation system. The ZW97 is a Z-Wave enabled device and is fully compatible with any Z-Wave Plus enabled network.Each module is designed to act as a repeater,which will re-transmit a radio frequency (RF),signal by routing the signal around obstacles and radio dead spots to ensure that the signal is received at its intended destination.Basic Operation:The ZW97 can control two channel outlet outputs separatelyPress the button one times controller all outlet ON/OFFPress the button two times controller left outlet ON/OFFPress the button three times controller right outlet ON/OFFFollow this 2-step procedure to add your new ShowHome device to your Z-Wave network: 1 Put your Z-Wave controller into inclusion mode. Consult your controller manual if you’re unsure how to do this. 2 Press the button five times. This will take a few moments to complete.MANUAL RESET - To be used only in the event that the network primary controller is lost or otherwise inoperable.)MANUAL RESET - To be used only in the event that the network primary controller is lost or otherwise inoperable.) 1）power off 2 ) hold on 5 seconds when turn on the power of ZW97 -----B: ON/OFF/PROG Push button -----C: Z-Wave controlled left outlet -----D: Z-Wave controlled right outlet -----Node: There are LED instructions below the button White LED indicates ON/OFF RED LED indicates temperature alarmInclude ZW97 to/from a Z-Wave Gateway with supporting Security the ZW97 can support the Primary Controller that implemented the security S2.Refer to your primary controller instructions to process the Secure Inclusion.The Below listed Command Class are all supported the Security S2COMMAND_CLASS_ZWAVEPLUS_INFO,COMMAND_CLASS_VERSION, COMMAND_CLASS_MANUFACTURER_SPECIFIC,COMMAND_CLASS_DEVICE_RESET_LOCALLY, COMMAND_CLASS_ASSOCIATION,COMMAND_CLASS_ASSOCIATION_GRP_INFO,COMMAND_CLASS_POWERLEVEL,COMMAND_CLASS_SWITCH_BINARY,COMMAND_CLASS_SWITCH_ALL,COMMAND_CLASS_CONFIGURATION,COMMAND_CLASS_NOTIFICATION_V8,COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V2,COMMAND_CLASS_TRANSPORT_SERVICE_V2,COMMAND_CLASS_SECURITY,ADCBCOMMAND_CLASS_SECURITY,COMMAND_CLASS_SECURITY_2,COMMAND_CLASS_SUPERVISIONCOMMAND_CLASS_FIRMWARE_UPDATE_MD_V4
Support for Association GroupsZW97 supports 3 association groups. A maximum of 5 node ID. -Association group_1: Association group_1 is default to associate with the primary controller (Gateway/Hub/Controller) for ZW97 Status change report, refer to below for report details: 1. ZW97 will trigger AUTO report function if the Output status had been changed. 2. Device Reset Locally Notification(Only report when the ZW97 has been triggered the RESET TO DEFAULT) -Association group_2: After receiving a basic set command from a local switch or gateway, On (0xFF) or Off (0x00), the ZW97 of left outlet will automatically send out a related basic set command, On (0xFF) or Off (0x00) to its associated group. -Association group_3: After receiving a basic set command from a local switch or gateway, On (0xFF) or Off (0x00), the ZW97 of right outlet will automatically send out a related basic set command, On (0xFF) or Off (0x00) to its associated group.LED indicator setting： 1）manual setting： Default lamp on, indicate LED ON Hlod button 5S lamp on, indicate LED OFF Hlod button 10S No Work 2）Parameter setting： Parameter=1, Size=1byte, Value=00(Default) lamp ON, indicate LED ON Parameter=1, Size=1byte, Value=00(Default) lamp ON, indicate LED ON Parameter=1, Size=1byte, Value=01 lamp ON, indicate LED OFF Parameter=1, Size=1byte, Value=02 LED OFF, NO WorkCountdown off setting: Parameter =2, Size=2byte, value=xx xx left outlet Countdown(Default00 00，MAX 36000 S) Parameter =3, Size=2byte, value=xx xx right outlet Countdown(Default00 00，MAX 36000 S)Temperature alarm When the temperature is greater than 105 degrees Celsius, equipment protection, stop output, send high temperature alarm.SPECIFICATIONSPower Requirements 120v / 60 HzMax Load 15Amp Max Smart Outlet1,15Amp Max Smart Outlet2, Total 15Amp MAX .Z-Wave Frequency 908.42 MHz Range 100 ft. (open air)Certifications UL (US, Canada), FCC, Z-Wave Plus
FCCCaution.Thisdevicecomplieswithpart15oftheFCCRules.Operationissubjecttothefollowingtwoconditions:(1)Thisdevicemaynotcauseharmfulinterference,and(2)thisdevicemustacceptanyinterferencereceived,includinginterferencethatmaycauseundesiredoperation.AnyChangesormodificationsnotexpresslyapprovedbythepartyresponsibleforcompliancecouldvoidtheuser'sauthoritytooperatetheequipment.Note:ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassBdigitaldevice,pursuanttopart15oftheFCCRules.Theselimitsaredesignedtoprovidereasonableprotectionagainstharmfulinterferenceinaresidentialinstallation.Thisequipmentgeneratesusesandcanradiateradiofrequencyenergyand,ifnotinstalledandusedinaccordancewiththeinstructions,maycauseharmfulinterferencetoradiocommunications.However,thereisnoguaranteethatinterferencewillnotoccurinaparticularinstallation.Ifthisequipmentdoescauseharmfulinterferencetoradioortelevisionreception,whichcanbedeterminedbyturningtheequipmentoffandon,theuserisencouragedtotrytocorrecttheinterferencebyoneormoreofthefollowingmeasures:‐Reorientorrelocatethereceivingantenna.‐Increasetheseparationbetweentheequipmentandreceiver.‐Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhichthereceiverisconnected.‐Consultthedealeroranexperiencedradio/TVtechnicianforhelp.*RFwarningforMobiledevice:ThisequipmentcomplieswithFCCradiationexposurelimitssetforthforanuncontrolledenvironment.Thisequipmentshouldbeinstalledandoperatedwithminimumdistance20cmbetweentheradiator&yourbody.

Navigation menu