Willis Electric ZW97 Outdoor Smart Plug User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3589565
Application ID	RNg8kzBDtfDIv0amwonm2A==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	28.91kB (361376 bits)
Date Submitted	2017-10-02 00:00:00
Date Available	2017-10-02 00:00:00
Creation Date	2017-09-27 16:48:19
Producing Software	Adobe Acrobat Pro 10.1.2
Document Lastmod	2017-09-27 16:48:19
Document Title	User Manual
Document Creator	PScript5.dll Version 5.2.2
Document Author:	Mac.Nie

ZW97 Z-Wave 2-Channel OutDoor Smart Plug
Introduction:
Thank you for choosing the ZW97 Z-Wave control product.ZW97 enabled product allows users to remotely
control lighting, home appliance, and make home control easy with low installation and maintenance costs.
You may begin with a few Z-Wave enabled devices as well as some of our products to build up acomplete
home automation system.
The ZW97 is a Z-Wave enabled device and is fully compatible with any Z-Wave Plus enabled network.Each
module is designed to act as a repeater,which will re-transmit a radio frequency (RF),signal by routing the
signal around obstacles and radio dead spots to ensure that the signal is received at its intended destination.
Basic Operation:
The ZW97 can control two channel outlet outputs separately
Press the button one times controller all outlet ON/OFF
Press the button two times controller left outlet ON/OFF
Press the button three times controller right outlet ON/OFF
Follow this 2-step procedure to add your new ShowHome device to your Z-Wave network:
1 Put your Z-Wave controller into inclusion mode. Consult your controller manual if you’re unsure how to do this.
2 Press the button five times. This will take a few moments to complete.
MANUAL RESET - To be used only in the event that the network primary controller is lost or otherwise inoperable.)
1）power off
2 ) hold on 5 seconds when turn on the power of ZW97
-----B: ON/OFF/PROG Push button
-----C: Z-Wave controlled left outlet
-----D: Z-Wave controlled right outlet
-----Node: There are LED instructions below the button
White LED indicates ON/OFF
RED LED indicates temperature alarm
Include ZW97 to/from a Z-Wave Gateway with supporting Security the ZW97 can support the Primary Controller that implemented the security S2.
Refer to your primary controller instructions to process the Secure Inclusion.The Below listed Command Class are all supported the Security S2
COMMAND_CLASS_ZWAVEPLUS_INFO,
COMMAND_CLASS_VERSION,
COMMAND_CLASS_MANUFACTURER_SPECIFIC,
COMMAND_CLASS_DEVICE_RESET_LOCALLY,
COMMAND_CLASS_ASSOCIATION,
COMMAND_CLASS_ASSOCIATION_GRP_INFO,
COMMAND_CLASS_POWERLEVEL,
COMMAND_CLASS_SWITCH_BINARY,
COMMAND_CLASS_SWITCH_ALL,
COMMAND_CLASS_CONFIGURATION,
COMMAND_CLASS_NOTIFICATION_V8,
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V2,
COMMAND_CLASS_TRANSPORT_SERVICE_V2,
COMMAND_CLASS_SECURITY,
COMMAND_CLASS_SECURITY_2,
COMMAND_CLASS_SUPERVISION
COMMAND_CLASS_FIRMWARE_UPDATE_MD_V4
Support for Association Groups
ZW97 supports 3 association groups. A maximum of 5 node ID.
-Association group_1:
Association group_1 is default to associate with the primary controller (Gateway/Hub/Controller) for ZW97 Status change report,
refer to below for report details:
1. ZW97 will trigger AUTO report function if the Output status had been changed.
2. Device Reset Locally Notification(Only report when the ZW97 has been triggered the RESET TO DEFAULT)
-Association group_2:
After receiving a basic set command from a local switch or gateway, On (0xFF) or Off (0x00), the ZW97 of left outlet will automatically
send out a related basic set command, On (0xFF) or Off (0x00) to its associated group.
-Association group_3:
After receiving a basic set command from a local switch or gateway, On (0xFF) or Off (0x00), the ZW97 of right outlet will automatically
send out a related basic set command, On (0xFF) or Off (0x00) to its associated group.
LED indicator setting：
1）manual setting：
Default
lamp on, indicate LED ON
Hlod button 5S
lamp on, indicate LED OFF
Hlod button 10S
No Work
2）Parameter setting：
Parameter=1, Size=1byte, Value=00(Default)
lamp ON, indicate LED ON
Parameter=1, Size=1byte, Value=01
lamp ON, indicate LED OFF
Parameter=1, Size=1byte, Value=02
LED OFF, NO Work
Countdown off setting:
Parameter =2, Size=2byte, value=xx xx left outlet Countdown(Default00 00，MAX 36000 S)
Parameter =3, Size=2byte, value=xx xx right outlet Countdown(Default00 00，MAX 36000 S)
Temperature alarm
When the temperature is greater than 105 degrees Celsius, equipment protection, stop output, send high temperature alarm.
SPECIFICATIONS
Power Requirements
120v / 60 Hz
Max Load
15Amp Max Smart Outlet1,15Amp Max Smart Outlet2, Total 15Amp MAX .
Z-Wave Frequency
908.42 MHz
Range 100 ft. (open air)
Certifications
UL (US, Canada), FCC, Z-Wave Plus
FCC Caution.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates
uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
‐Reorient or relocate the receiving antenna.
‐Increase the separation between the equipment and receiver.
‐Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
‐Consult the dealer or an experienced radio/TV technician for help.
*RF warning for Mobile device:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator & your body.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : Yes
Author                          : Mac.Nie
Create Date                     : 2017:09:27 16:48:19+08:00
Modify Date                     : 2017:09:27 16:48:19+08:00
Title                           : 
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Metadata Date                   : 2017:09:27 16:48:19+08:00
Creator Tool                    : PScript5.dll Version 5.2.2
Format                          : application/pdf
Creator                         : Mac.Nie
Document ID                     : uuid:b38483a3-37e2-4842-832f-882c341e40b5
Instance ID                     : uuid:c7140db9-88b3-4ed5-96ef-9d09a06a42d4
Producer                        : Adobe Acrobat Pro 10.1.2
Page Count                      : 3

EXIF Metadata provided by EXIF.tools