Winnix Technologies HYM360 UHF RFID Reader Module User Manual user s manualx

Winnix Technologies Co., Limited UHF RFID Reader Module user s manualx

Manual

UHF RFID Reader Module UHF RFID Reader Module HYM360 WinnixTechnologiesCo.,Limited
UHF RFID Reader Module Brief Introduction HYM360 UHF Reader Module complied with EPC C1G2 Protocol, its working frequency is 902.75-927.25MHz, with standard 2dBi antenna, the reading distance can reach 2 meters. With low power consumption, simple power supply and interface circuit, a high-performance and cost-effective RFID system can be established. It is suitable for retail，access control, medical industry, food tracking, anti-counterfeit and so on, especially for small size hand-held UHF RFID reader. Technical Date No. Item Technical Date Unit Remark 1 Fixed Current ≤380 mA 25dBm 2 Standby Current ≤1 mA EN Pin Low Level 3 Frequency Range 902.75-927.25 MHz 4 Default Working Frequency Hopping Frequency MHz Frequency Interval 250KHz 5 Fixed Power 25 dBm Max 27dBm 6 Stepping Interval 1 dBm 10~25dBm adjustable by soft 7 Label Protocol EPC C1G2 /ISO18000-6C 8 Starting Time ≤50 ms 9 VSWR ≤1.5 10 Max Reading Range 2 m 2dBi Antenna Characteristics of DC Data Min Value Typical Value Max Value Unit Remark Voltage of Power 3.3 4.2 5 V DC Input High Level 2 3.3 3.5 V GPIO 2 - 5 V EN Input Low Level -0.5 0 0.5 V GPIO - - 0.18 V EN Output High Level 2.3 - 3.3 V GPIO Output Low Level 0 - 1 V GPIO Enable Current 2 5 25 uA VEN≥2V
UHF RFID Reader Module Requirement on Antenna Product Features Electrical Properties: It is a general antenna for UHF RFID applications with high gain and low VSWR. Mechanical Properties: The compact and artistic antenna is suitable for all kinds of severe environment for its dual waterproof design with Gasket and silicone and strengthening rib of shell. Performance Specifications  Frequency Range:860MHz～960MHz  Maximum VSWR: ≤1.3:1  Gain: > 9 dBi  H side HPBW: 70°  E side HPBW: 70°  Polarization: Circular Polarization  Relative humidity: 5%～95%  Input Impedance: 50 Ω  Antenna Connection: N-50KFD (Type N Female) Physical specifications  Size: 258mm×258mm×56mm  Weight: 0.91kg(without bracket)  Material: Engineering Plastic ASA、Aluminums  Color: Ivory-white  Enclosure Rating: IP67  Operational Temperature: -40℃~+ 85℃  Storage Temperature: -40℃~+ 85℃ Figure 1. The photograph of the antenna
UHF RFID Reader Module Installation guide HYN503 antenna can be installed on steal framed structure or bracket by own antenna bracket, and connect with reader with coaxial line. The antenna can be installed horizontally or vertically, it is decided by installation location, the angle can be adjusted after installation according to the real environment. Antenna bracket is an optional accessory, you can choose according to your special requirement. 1. Installation Dimension Figure 2 Dimension of the antenna 2. Installation Steps 2.1 Horizontal Installation Step 1：Use M6 screw, elastic washer and plain washer, to fix the L board on the antenna, please see Figure 3:. Figure 3 The structure for the Step 1 in the first case Step 2：Please use M6 screw, elastic washer and plain washer and “Dog tooth” to fix it on the horizontal and vertical bracket, please see Figure 4. 1 L board（Bracket） 2．M6 screw, elastic washer and plain washer
UHF Antenna 1 M6 screw, elastic washer and plain h2 Dog tooth3 M6 U style screw bolt Figure 4. The structure for the Step 2 in the first case 2.2 Vertical Installation Step 1：Use M6 screw, elastic washer and plain washer, to fix the L board on the antenna, as shown in Figure 5. Figure 5 The structure for the Step 1 in the second case Step 2：Please use M6 screw, elastic washer and plain washer and “Dog tooth” to fix it on the horizontal and vertical bracket, as shown in Figure 6. 1 L board（Bracket） 2．M6 screw, elastic washer and plain washer
UHF RFID Reader Module 6 / 9 Figure 6 The structure for the Step 2 in the second case 1 M6 screw, elastic washer and plain washer 2 Dog tooth 3 M6 U style screw bolt
UHF RFID Reader Module 7 / 9 Appearance and Structure Drawing 1 Size of Reader Module Interface Definition PIN Signal Name Signal Direction Function/Compatibility Description 1~2 NC NC 3~6 GND - Module Connecting Ground 7 VDD Input Module Supplying power 8 EN Input Module Enabling, Highly Effective 9 GPIO Output 10 GPIO Output 11 UART_RX Input 12 UART_TX Output 13~16 GND - Module connecting ground 17 RFOUT Bidirection Module Radio frequency Input and output interface 18~24 GND - Module connecting ground
UHF RFID Reader Module 8 / 9 Environment Requirement No. Item Technical Data Unit Remark 1 Working temperature -20～+70 ℃ 2 Storage temperature -40～+85 ℃ 3 Relative humidity 10%～90% RH Circuit for Reference Drawing 2 Circuit for reference Warning This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
UHF RFID Reader Module 9 / 9 NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. RF Exposure Statement To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna. If the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains Transmitter Module FCC ID: RVZHYM360” or “Contains FCC ID: RVZHYM360” Please describe the following warning to the manual. This LMA is tested and approved as standalone configuration, additional evaluation may be required for any system integrated this radio module.

Navigation menu