Winnix Technologies HYM740 UHF RFID Reader Module User Manual

Download:
Mirror Download [FCC.gov]
Document ID	2113172
Application ID	jsWUeG3KFp82TIV3Nnn0gQ==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	30.55kB (381882 bits)
Date Submitted	2013-11-07 00:00:00
Date Available	2013-11-07 00:00:00
Creation Date	2013-05-08 16:05:26
Producing Software	Acrobat Distiller 7.0.5 (Windows)
Document Lastmod	2013-11-06 19:08:18
Document Title	Microsoft Word - user manual.doc
Document Creator	PScript5.dll Version 5.2
Document Author:	0162

UHF RFID Reader Module
HYM740
Winnix Technologies Co.,Limited
RFID Reader Module
Brief introduction
HYM740 UHF RFID reader uses R2000 chip, which complies with EPC C1G2
protocol, its working frequency is 902~928MHz，with LBT function. It supports dense
reader working mode（DRM）。With standard 7dBi antenna，the reading distance can
reach 24 meters, maximum identifying speed can reach 400/S; with simple power
supply and interface circuit, a high-performance RFID system can be established. It is
suitable for logistics, apparel, medical industry, and complex assets management, etc.
Technical data
No
Item
Technical data
Unit
Remark
Max power output
EN pin low level
Frequency interval 250KHz
Max current
Standby current
1.2
≤1
Frequency range
902～928
mA
MHz
Default
frequency
Frequency hopping
MHz
≤250
≤2
KHz
working
Channel bandwidth
Frequency hopping
speed
Fixed power
30
dBm
Stepping interval
1~2
dB
Label protocol
EPC C1G2
/ISO18000-6C
10
Communication
protocol
Asynchronous serial
ports protocol
11
Starting time
12
13
14
Radio-frequency
power rising time
Radio-frequency
power dropping time
Adjacent
channel
power leaking ratio
15
Frequency
stabilizing ratio
16
Max reading range
17
Multi-tags
5~30dBm， adjustable by
software
≤50
ms
≤500
μs
≤500
μs
≤-40
≤-60
±10
dB
dB
ppm
±1CH
±2CH
-25℃～+40℃
±20
ppm
-40℃～+60℃
24
7dBi antenna
>400/s
-2-
RFID Reader Module
Characteristics of DC
Data
Voltage of power
Input high level
Input low level
Output
high
level
Output low level
Enable current
Mini
value
4.5
-0.3
Typical
value
3.3
2.9
Max value
Unit
Remark
5.5
5.5
0.8
0.18
Direct current
GPIO
EN
GPIO
EN
GPIO
0.1
25
uA
VEN≥2V
GPIO
Requirement on antenna
No
Item
Technical data
Standing wave
ratio
≤1.5
Appearance and structure
Size: 76.5×39.7×9mm
Weight: 50g
-3-
Unit
Remark
RFID Reader Module
Drawing 1 Front view of the reader
-4-
RFID Reader Module
Drawing2 Side view of the reader
Drawing3 Pin connector
-5-
RFID Reader Module
Interface definition
Pin
Signal name
Signal direction
Function/compatibility description
VCC
Input
Module supplying power
VCC
Input
Module supplying power
GND
Module connecting ground
GND
Module connecting ground
EN
Input
Module enabling，highly effective
GPIO
Bidirection
Generic port
GPIO
Bidirection
Generic port
GPIO
Bidirection
Generic port
UART_RX
Input
Asynchronous serial interface receiving
10
UART_TX
Output
Asynchronous serial interface sending
11
DBG_RX
Test port
12
DBG_TX
Test port
OEMs information: RealID Technology Co., Ltd. was established in December 2012, the
registered capital of 990 million yuan. It is a professional company specializing in RFID system
design, equipment development and related technical services. RealID Technology Co., Ltd.
gathered a number of highly qualified management personnel, first-class product development
elite, to provide customers with first-class hardware products, program design, and custom
services.
Changes or modifications made to the equipment not expressly approved by Winnix may void the
FCC / IC authorization to operate this equipment.
The use of the transceiver module is authorized in mobile or fixed host devices taking into account
the conditions listed below
:• OEM Integrator must ensure that the end user manual may not contain any information about
the way to install or remove the module from the final product.
• Depending on the final host device additional authorization requirements for the nontransmitter
functions of the transmitter module may be required (i.e., Verification, or Declaration of
Conformity) The OEM integrator is responsible for ensuring that a er the module is installed and
operational the host continues to be compliant with the Part 15B unintentional radiator
requirements.
• The information on the label and in the user manual is required to be incorporated in the user
manual of the final host. see 47 CFR15 requirements for more details (e.g. 15.19 / 15.21 / 15.101 /
15.105 / RSSGEN / ICES)
• Additional label with the words ‘Contains FCC ID: RVZHYM740’ shall be applied and visible
from the outside of the host product.
-6-
RFID Reader Module
• The module must be installed and used in strict accordance with the manufacturer’s instructions
as described in the user documenta on that comes with the module
.• The end user manual for the final host product operating with this transmitter must include
operatng instructions to satisfy RF exposure compliance requirements. e.g
Radiofrequency radiation exposure Information:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance of 25 cm
between the radiator and your body.This transmitter must not be colocated or operating in
conjunction with any other antenna or transmitter
.• When the final host product operating with this transmitter deviate from above, installation of
this module into specific final hosts may require the submission of a Class II permissive change
application containing data pertinent to RF Exposure, spurious emissions, ERP/EIRP, and
host/module authen ca on, or new application if appropriate
Feel free to contact us if additional guidance is required.
Manual Requirements according 15.19 / RSSGEN
This device complies with Part 15 of the FCC Rules [and with Industry Canada licence exempt
RSS standard(s)].
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired opera on.
Manual Requirements according 15.21
Changes or modifi ca ons made to this equipment not expressly approved by (manufacturer name)
may void the FCC authorization to operate this equipment.
Environment requirement
No
Item
Working
temperature
Storage
temperature
Relative
humidity
Technical data
Unit
-25～+75
℃
-40～+85
℃
10%～90%
RH
-7-
Remark
RFID Reader Module
Declaration
1) Marketing
The device must be sold to dealers.
2) Professional installation
Installed by licensed professionals ( EUT sold to dealer who hire installers)
3) Application
The intended use is generally not for the general public. It is generally for industry/commercial
use.
RF EXPOSURE
This Module complies with FCC RF radiation exposure limits set forth for an uncontrolled
environment under the following condition: The device shall be used in such way that at least a
distance of 25 centimeters is maintained between the antennas and the body of the user and nearby
persons.
Antenna Information
The HY740 includes an external antenna port.
Here are some design guidelines to help ensure antenna performance:
. Never place the ground plane or route copper traces directly underneath the antenna portion of
the module.
. Never place the antenna close to metallic objects.
. In the overall design, ensure that wiring and other components are not placed near the antenna.
. Do not place the antenna in a metallic or metallized plastic enclosure.
. Do not place the antenna in a metallic or metallized plastic enclosure.
. Keep plastic enclosures 1cm or more from the antenna in any direction.
-8-

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Extract, Print high-res
XMP Toolkit                     : 3.1-702
Producer                        : Acrobat Distiller 7.0.5 (Windows)
Creator Tool                    : PScript5.dll Version 5.2
Modify Date                     : 2013:11:06 19:08:18+08:00
Create Date                     : 2013:05:08 16:05:26+08:00
Metadata Date                   : 2013:11:06 19:08:18+08:00
Format                          : application/pdf
Title                           : Microsoft Word - user manual.doc
Creator                         : 0162
Document ID                     : uuid:28a77b8f-98d2-4d15-bab0-3f93d4cffc50
Instance ID                     : uuid:700c6285-f5c7-4990-a720-0758a955d19e
Page Count                      : 8
Author                          : 0162

EXIF Metadata provided by EXIF.tools