Wireless Cables AB5C1 Bluetooth Module User Manual FCC request

Wireless Cables Inc. Bluetooth Module FCC request

Contents

OEM installation guide

Wireless Cables Inc.
2880 Zanker Rd, Suite 203
San Jose, CA 95134
Phone: (408) 850-1884
Fax: (408) 228-0687
Email: juergen@aircable.net
Bluetooth Module
AIRcable SMD, AB5C1
USER GUIDE
V1.1
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one of the following measures:
● Reorient or relocate the receiving antenna.
● Increase the separation between the equipment and receiver.
● Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
● Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired
operation.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
Wireless Cables Inc.
2880 Zanker Rd, Suite 203
San Jose, CA 95134
Phone: (408) 850-1884
Fax: (408) 228-0687
Email: juergen@aircable.net
This mobile device is intended for general use.
THE TRANSMITTING ANTENNA MUST BE LOCATED MORE THAN 20cm AWAY FROM
THE BODY OF USER AND NEAR BY PERSON.
1) The transmitter module may not be co-located with any other transmitter or antenna.
As long as condition above are met, further transmitter test will not be required. However,
the OEM integrator is still responsible for testing their end-product for any additional
compliance requirements required with this module installed (for example, digital device
emissions, PC peripheral requirements, etc.).
IMPORTANT NOTE: In the event that these conditions can not be met (for example
certain laptop configurations or co-location with another transmitter), then the FCC
authorization is no longer considered valid and the FCC ID can not be used on the final
product. In these circumstances, the OEM integrator will be responsible for re-evaluating
the end product (including the transmitter) and obtaining a separate FCC authorization.
End Product Labeling
The final end product must be labeled in a visible area with the following:
“Contains FCC ID: SQCAB5C1”.
Manual Information That Must be Included
The users manual must include the following information in a prominent location:
Example Sticker:
This Transmitter must not be co-located or operating in conjunction with any other antenna
or transmitter. This equipment complies with FCC RF radiation exposure limits set forth for
an uncontrolled nvironment. This equipment should be installed and operated with a minimum
distance of 20 centimeters between the radiator and your body. Any changes or modifications
(including the antennas) made to this device that are not expressly approved by the manufacturer
may void the user’s authority to operate the equipment.
IMPORTANT NOTE:
Wireless Cables Inc.
2880 Zanker Rd, Suite 203
San Jose, CA 95134
Phone: (408) 850-1884
Fax: (408) 228-0687
Email: juergen@aircable.net
Description
Wireless Cables Inc. provides various Bluetooth products. They are suitable for customers to
exploit them to implement Bluetooth functionality into PCs. The features of Bluetooth USB
interface list as below:
Features
Model Name AB5C1
Standard Bluetooth v2.1
Frequency Band 2.4~2.4835GHz unlicensed ISM band
Spread Spectrum FHSS (Frequency Hopping Spread Spectrum)
RF Output Power Class 1 (18.91 dBm)
DC power 5V or Lithium battery
I/O Interface
USB Compliant USB V2.1
Overair Baud rate 720kBit/s,
Audio intput and output, differential
16 PIO, 2 AIO, asynchronous and synchronous serial
Dimension 25 x 14.5 mm
Photos
Wireless Cables Inc.
2880 Zanker Rd, Suite 203
San Jose, CA 95134
Phone: (408) 850-1884
Fax: (408) 228-0687
Email: juergen@aircable.net
Wireless Cables Inc.
2880 Zanker Rd, Suite 203, San Jose, CA 95134
T 408.850.1884 ~ F 408.228.0687
sales@aircable.net ~ www.aircable.net
Software Specification
Hardware Specification
BASIC Interpreter Line numbers: 1-2047
Line length: 32 characters
Loop nesting: 6
Subroutines: 8 levels
Expressions: -32768 to 32767, 16-bit
Variables: 25, ‘A’ - ‘Y’, variable ‘Z’ used for debugging
String variable: $0 volatile 80 bytes long
String variables: $1-$2047, 32 byte length
Character size: 8 bit
Expression parser recursive, maximum of 5 levels
File system: BASIC and config file independent
PIN code limit: 15 characters
Programmable from other AIRmote devices
Programm load from standard file system
Event Handling PIN code request
Incoming SPP connection
Outgoing SPP connection success
Sensor readings (connection quality, temperature, analog input)
Incoming vNote through OBEX
Inquiry results
SPP control indicator (DTR signal)
PIO change event
Timer messages
Interrupt Routines 2 levels: high priority interrupt: stops BASIC program execution
low priority: schedules execution
Bluetooth Bluetooth 2.1 certified, with 802.11 tolerance
EDR supported where available
Profiles master and slave mode simultanously
Two SPP profiles for streaming data at the same time
OBEX/FTP for file transfer of BASIC and config file
FTP server profile
OBEX vNote item transfer for messages
OBEX vCard business card exchange
OBEX server and OBEX client profile
up to 4 multiple connections at the same time
Security control, pairing and un-pairing functions
Certifications Bluetooth certified (BQB)
FCC and IC module certification
CE certified
RoHS compliant
Sensor Interfaces Parallel IO ports, 16 ports TTL level, 5V tolerant
Security overwrite port
2 analog input
UART configurable 1200 to 1382400 baud, parity and stop bits
I2C master interface, fast mode
SPI via general purpose PIO
Built-in Functions powerful high level Bluetooth functions, slave connect, master, send
biz card,
hardware control, pio input/output, uart, baud rate, sensor, date
string operations, hex and ascii conversion, compare, length
input and output, on 2 SPP, 1 UART, files and virtual string
data logging
LCD 8 character display via I2C
File system access to application BASIC program
read/write configuration file
wireless file transfer (OBEX), up/downloadable
Performance max 2000 lines per second
standard: 100 lps
scheduler resolution 10ms
max 350kBit/s streaming data
recommended max average: none
fastest connect time < 2s
FTP file system: 16 kbps,
Radio Device name configurable
Bluetooth class configurable
Max and default transmit power configurable
Scan modes configurable to as low as 30uA power consumption
Sniff mode configurable (soon)
Firmware 112000 words code size operating system
RTOS for baseband radio
Customizations additional embedded functions
audio profiles (audio gateway, headset, handsfree)
networking profiles (TCP)
web server
Processor
BlueCore 5MM with DSP, 8BMit internal flash, 512kBit EEPROM
Size 14.5 mm x 24.5 mm
Pins vertical 2 rows of 18 pins, 2 horizontal rows of 11 pins
spaced 1.27 mm
SMD pad mounted
Uart 1200 to 1382400 baud, 3.3V TTL level, 5V tolerant
Antenna
connection
50 Ohm Impedance
Power Supply 5V regulated stand-alone
Lithium rechargeable battery, 4.2V, 100-500mAH
3V primary cells
Battery Charger 25mA-100mA configurable Lithium battery charger
requires current protected Lithium rechargeable batteries
Power consumption 30uA sleep, 11mA with connection, up to 250mA peek
Input and Output 16 digital input/output lines (3.3V TTL, 5V tolerant)
2 analog input lines (0-1.8V)
2 LED current sinks, 4.2V tolerant
Asynchronous
serial
1200-1382400 bps, 8 bit, none-odd-even parity, 1 or 2 stop bits
Radio raw output power: 20dBm
receiver sensitivity: -96dBm
range 200m
Sensor Interfaces real time clock DS1372
temperature sensor TC54
16bit adc ADS1112
LCD controller PCF8562
general I2C and SPI master
Certifications Bluetooth certified (BQB)
Bluetooth 2.1 Standard (802.11b tolerant)
FCC module certification
CE certification (pdf)

Navigation menu