Wireless Environment MB130 Remote Controlled LED Light User Manual

Wireless Environment LLC Remote Controlled LED Light Users Manual

Users Manual

1. Remove front cover of Spotlight by rotating count-er-clockwise as shown above. Pull face out from cup to reveal battery holder.Spotlight features:Fully Adjustable: Light can be rotated 360° as well as up and downLight Coverage: up to 400 sq ftDurable, Weather Resistant: Tight seals and UV resistant material allow the light to work in all weather conditionsRemote Control: Control from up to 70 ft away 2. Push down on battery door tab to release. Insert 3 D-Cell batteries into Spotlight. Attach battery door by matching the tabs to the rectangular holes and then push down on front until door clicks into place.4. Match arrows then turn clock-wise. Make sure unit is securely closed with arrow pointing at the lock symbol to ensure weather proof seal is tight.10. Loosen larger thumb screw that connects Spotlight head to mounting base and adjust Spotlight head to proper direction as shown above. Tight-en thumb screw.32333 Aurora Rd. Suite 100 Solon, OH 44139877.298.9082Installation InstructionsCustomizable Wireless Spotlight with Motion Sensor and Remote ControlMB130• 1 Small Screwdriver• 3 D-Cell Alkaline Batteries• 1 Remote Controlled Spotlight• Mounting Base• 3 Screws & 3 Anchors• 1 Remote Control with Mounting Bracket + 2 screws• (1) 3V Coin BatteryLED LightMounting BaseMounting Base Thumb ScrewKnuckle ScrewMotion & Light SensorDimBright Motion ControlIndicator LightMountingBracketSyncing your lightWhat you need to install:What is included per light:www.mrbeams.com5. Determine location for mount-ing Spotlight. NOTE: For best performance, Spotlight should be positioned so motion sensor is on top and light is on bottom. 6. Remove mounting base by turning thumb screw counter- clockwise.7. Pull mounting base o stem.8. Drive three screws into the three holes located on mounting base.9. Insert spotlight stem back into mounting base pointed in desired direction and tighten thumb screw in base.Tips: • Use only new alkaline D-Cell batteries with 1.5V rating. • Do not mix old and new batteries. If batteries are not new, it may cause light to malfunction. • Install batteries with polarity in correct position. • Antenna is only connected at one end. It acts as a receptor for the remote. * 1 year limited warranty. See enclosed card for details.* Visit our website to view installation video.Battery Caution: 1) Do not mix old and new batteries2) Do not mix Alkaline, Standard (Carbon-Zinc) or Rechargeable (Nickel Cadmium) or (Nickel Metal Hydride) batteries3) Do not dispose of batteries in re4)Batteries should be recycled or disposed of as per state and local guidelines1. The remote is paired to work only with the Spotlight it is packaged with. To sync additional spotlights to a single remote, press the exposed black button on the spotlight next to the battery compartment for 3 seconds while pressing the ON button on the remote. 1. Open the Remote Control with a small coin and insert one at 3V battery (included) as shown on the inside of the Remote Control. Smooth side of battery should be facing up.2. Determine placement for bracket for remote and attach to wall using two screws (included) or tape.3. Slide Remote into bracket as shown above. Patent # 8,203,445Using the remoteSet upSpotlight will activate when motion is sensed from up to 30 ft away. Motion sensor only activates in darkness to conserve energy.Activate light with the remote. Hold the motion sensor button down until light blinks. When it blinks 2x the motion sensor has been disabled. When it blinks 4x, the motion sensor has been enabled. Light will remember your last brightness setting. Spotlight can be turned on or o by pressing the remote control. Activat-ing the remote will override the light sensor, and light can be activated at any time. Default mode is motion sensor on 30 second auto shut-o.First activate the light with remote control. Next, hold the ON button down until light blinks. When it blinks 1x, auto shut o is set to 1 hour. When it blinks 2x, it is set to 4 hours.First activate the light with remote control. Next, press the Bright or Dim button on the remote to adjust the brightness. Brightness Options: 60, 90, or 140 lumens.Customize your remote settingsMotion Sensor ActivationDisable MotionRemote Control Activation2 Auto Shut-off Options3 Brightness Modes
Power supply: DC 3VOperating Frequency:433.7MHzFCC ID: W7DMB1301. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference.(2) This device must accept any interference received, including interference that may cause undesired operation.2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Navigation menu