Wireless Environment MB130 Remote Controlled LED Light User Manual
Wireless Environment LLC Remote Controlled LED Light Users Manual
Users Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 2272507 |
| Application ID | +wQzhvF4tkBwgx6vNhUhLg== |
| Document Description | Users Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 69.69kB (871079 bits) |
| Date Submitted | 2014-05-20 00:00:00 |
| Date Available | 2014-05-21 00:00:00 |
| Creation Date | 2014-03-14 12:48:44 |
| Producing Software | Adobe PDF Library 10.0.1 |
| Document Lastmod | 2014-05-13 23:59:22 |
| Document Title | Users Manual |
| Document Creator | Adobe InDesign CS6 (Macintosh) |
Installation Instructions Customizable Wireless Spotlight with Motion Sensor and Remote Control MB130 Spotlight features: Fully Adjustable: Light can be rotated 360° as well as up and down Light Coverage: up to 400 sq ft Durable, Weather Resistant: Tight seals and UV resistant material allow the light to work in all weather conditions Remote Control: Control from up to 70 ft away What is included per light: • 1 Remote Controlled Spotlight • Mounting Base • 3 Screws & 3 Anchors • 1 Remote Control with Mounting Bracket + 2 screws • (1) 3V Coin Battery What you need to install: • 1 Small Screwdriver • 3 D-Cell Alkaline Batteries LED Light Customize your remote settings Remote Control Activation Spotlight can be turned on or off by pressing the remote control. Activating the remote will override the light sensor, and light can be activated at any time. Default mode is motion sensor on 30 second auto shut-off. 2 Auto Shut-off Options First activate the light with remote control. Next, hold the ON button down until light blinks. When it blinks 1x, auto shut off is set to 1 hour. When it blinks 2x, it is set to 4 hours. 3 Brightness Modes First activate the light with remote control. Next, press the Bright or Dim button on the remote to adjust the brightness. Brightness Options: 60, 90, or 140 lumens. Motion Sensor Activation Spotlight will activate when motion is sensed from up to 30 ft away. Motion sensor only activates in darkness to conserve energy. Disable Motion Motion & Light Sensor Activate light with the remote. Hold the motion sensor button down until light blinks. When it blinks 2x the motion sensor has been disabled. When it blinks 4x, the motion sensor has been enabled. Light will remember your last brightness setting. Indicator Light Knuckle Screw Dim Motion Control Bright Mounting Base Thumb Screw Mounting Bracket Mounting Base Set up 1. Remove front cover of Spotlight by rotating counter-clockwise as shown above. Pull face out from cup to reveal battery holder. 2. Push down on battery door tab to release. Insert 3 D-Cell batteries into Spotlight. Attach battery door by matching the tabs to the rectangular holes and then push down on front until door clicks into place. 4. Match arrows then turn clockwise. Make sure unit is securely closed with arrow pointing at the lock symbol to ensure weather proof seal is tight. 5. Determine location for mounting Spotlight. NOTE: For best performance, Spotlight should be positioned so motion sensor is on top and light is on bottom. 6. Remove mounting base by turning thumb screw counterclockwise. 7. Pull mounting base off stem. Using the remote 1. Open the Remote Control with a small coin and insert one flat 3V battery (included) as shown on the inside of the Remote Control. Smooth side of battery should be facing up. 8. Drive three screws into the three holes located on mounting base. 9. Insert spotlight stem back into mounting base pointed in desired direction and tighten thumb screw in base. 10. Loosen larger thumb screw that connects Spotlight head to mounting base and adjust Spotlight head to proper direction as shown above. Tighten thumb screw. Syncing your light 2. Determine placement for bracket for remote and attach to wall using two screws (included) or tape. 3. Slide Remote into bracket as shown above. 1. The remote is paired to work only with the Spotlight it is packaged with. To sync additional spotlights to a single remote, press the exposed black button on the spotlight next to the battery compartment for 3 seconds while pressing the ON button on the remote. Tips: • Use only new alkaline D-Cell batteries with 1.5V rating. • Do not mix old and new batteries. If batteries are not new, it may cause light to malfunction. • Install batteries with polarity in correct position. • Antenna is only connected at one end. It acts as a receptor for the remote. Battery Caution: 1) Do not mix old and new batteries 2) Do not mix Alkaline, Standard (Carbon-Zinc) or Rechargeable (Nickel Cadmium) or (Nickel Metal Hydride) batteries 3) Do not dispose of batteries in fire 4)Batteries should be recycled or disposed of as per state and local guidelines Patent # 8,203,445 * Visit our website to view installation video. * 1 year limited warranty. See enclosed card for details. 32333 Aurora Rd. Suite 100 Solon, OH 44139 877.298.9082 www.mrbeams.com Power supply: DC 3V Operating Frequency:433.7MHz FCC ID: W7DMB130 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Tagged PDF : No XMP Toolkit : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04 Create Date : 2014:03:14 12:48:44-04:00 Metadata Date : 2014:05:13 23:59:22+08:00 Modify Date : 2014:05:13 23:59:22+08:00 Creator Tool : Adobe InDesign CS6 (Macintosh) Instance ID : uuid:9423eb70-a236-4ffb-9b1f-edab803bd627 Original Document ID : xmp.did:358C138F272068118C14D63ED8DFD8B8 Document ID : xmp.id:6BC9F7FF082068118083C6D35557ED0B Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:6AC9F7FF082068118083C6D35557ED0B Derived From Document ID : xmp.did:16E0AB050E2068118C14E3FCD8A6A241 Derived From Original Document ID: xmp.did:358C138F272068118C14D63ED8DFD8B8 Derived From Rendition Class : default History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CS6 (Macintosh) History Changed : / History When : 2014:03:14 12:48:44-04:00 Format : application/pdf Producer : Adobe PDF Library 10.0.1 Trapped : False Page Count : 2 Creator : Adobe InDesign CS6 (Macintosh)EXIF Metadata provided by EXIF.tools