Wonde Proud Technology WPBT55S BLUETOOTH GPS RECEIVER User Manual USERS MANUAL

Wonde Proud Technology Co., Ltd. BLUETOOTH GPS RECEIVER USERS MANUAL

UserManual.wiki >

Wonde Proud Technology >

WPBT55S User Manual

USERS MANUAL

*** USER’S MANUAL ***FCC ID : SRKWPBT55S

The Federal Communication Commission StatementThis equipment has been tested and found to comply with the limits for a Class B Digital Device,pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and canradiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful interference to radio communication. However, there is no guarantee thatinterference will not occur in a particular installation. If this equipment does cause harmfulinterference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of more of the following measures: --Reorient or relocate the receiving antenna.-Increase the separation between the equipment and receiver.-Connect the equipment into an outlet on a circuit different from that to which the receiveris connected.-Consult the dealer or an experienced Radio/TV technician for help.Use only shielded cables to connect I/O devices to this equipment. You are cautioned that change or modifications not expressly approved by the party responsible for compliance could void yourauthority to operate the equipment.THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFULINTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERECE RECEIVED,INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.1. This device may not cause harmful interference and2. This device must accept any interference received, including interference that may causeundesired operation.

User’s GuideGPS-BT55S GPS BT-55S User’s Guide

User’s GuideGPS BT-55S Table of Contents 1. Read Me First………………………………………………………………………………….. p.3 2. Box Contents…………………………………………………………………………………… p.3 3. Getting Started…………………………………………………………………………………. p.3 4. Hardware Description…………………………………………………………………………. p.7 5. LED Indicator…………………………………………………………………………………... p.8 6. Specification……………………………………………………………………………………. p.9 2

User’s GuideGPS BT-55S1. Read Me First 1. The battery must be charged for at least 8 hours for the ‘INITIAL’ use. The LED2 (ORANGE) will turn off after 3 hours’ charging, please keep on charging for 5 more hours. Thereafter, for each time’s battery charging please fully charge for 3 hours. 2. We strongly recommend that remove the battery if the device will not be used for over 2 weeks. Do not remove the battery within 2 weeks. 3. For fast data tracking purpose staying still before get fixed is recommended. (FIX then GOES!!) 4. Please note that the device will only receive the signal under the open sky. In this case, putting the device under the windshield is recommended. 2. Box Contents 1. GPS Bluetooth receiver 2. Lithium-ion rechargeable battery 3. Car charger 4. Power adapter 5. Document CD 3. Getting Started 1. Install the battery 3 2. Turn on the GPS Bluetooth receiver. Press the power button for 3 seconds or until the LED1 (GPS Fix Status) turns into RED and LED2 (Bluetooth Status) turns into Blue. 3. Activate Bluetooth function of your PDA / PC Prior to activating the Bluetooth function of your PDA / PC, please make sure the device is equipped with Bluetooth function, and the driver software has been installed. 4. Activate Bluetooth Manager & Established New Connections. Illustrations using HP 2100 PDA as follows: 1. First, find the device with which you wish to establish connection. 2. Open “Bluetooth Manager” on your pocket PC. 3. Press “New”. 4. Press "Connect”.

User’s GuideGPS BT-55S Click here Click here to select installation BTGPS 4

User’s GuideGPS BT-55S BTGPS ****Enter Pass Key " 0000", then Press “Enter” Enter key Click here Click here BTGPS BTGPS 5

User’s GuideGPS BT-55S Connection established BTGPS: SPP slave The connection between GPS Bluetooth receiver and PDA has been successfully established 5. Turn off the GPS Bluetooth receiver Press the power button for 3 seconds, all LEDs will goes off. We recommend that close the E-map before turning off the GPS Bluetooth receiver, in order to avoid any possible PDA /PC freeze. 6

User’s GuideGPS BT-55S4. Hardware Description LED2: Bluetooth StatusPower ButtonLED1: GPS Fix Status Charge Socket Push here to open Slip-resistant Slip-resistantPush here to open 7

User’s GuideGPS BT-55S 5. LED Indicator Power on: LED1: GPS Fix Status LED2: Bluetooth Status Red (ON) GPS not fixed yet! Blue (ON) Blinking for every 3 seconds (in paring mode) GPS get fixed/Bluetooth connected: LED1: GPS Fix Status LED2: Bluetooth Status Red Blinking for every 1 seconds Blue Blinking quickly Low battery: LED1 (GREEN) blinking for every 1 second Charging: LED2 (ORANGE) ON Charging: LED2 (ORANGE) ON Battery is fully charged: LED2 (ORANGE) turns off GPS Bluetooth operates on OS with Bluetooth function that supports SPP In order to avoid any unexpected problem, DO NOT attempt to change the default baudrate 8