Wooyoung Telecom HL500S LCD Monitor User Manual
Wooyoung Telecom Co., Ltd. LCD Monitor
User Manual
User¡¯ s Manual WOO YOUNG Telecom CO.,LTD. FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, with can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. - Only shielded interface cable should be used. Finally, any changes or modifications to the equipment by the user not expressly approved by the grantee or manufacturer could void the users authority to operate such equipment. Contents °°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°° °°°°°°°°°°°°°°°°°°°°°°°°° °°°°°°°°°°°°°°°°°°°°°°°°°°° °°°° °°°° ° °°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°° 1. Before Setting up Brief Specification of LCD Monitor Precautions 2. Items 3. Setting up the LCD monitor °°°°°°°°°°°°°°°°°°°°°°°°°° 8 Where is a good place to position the monitor? °°°°°°°°°°°°°°°°°° Check before connecting the power cord and the signal cable !! ° ° ° ° ° °° How to connect the power cord and the several cables to the LCD monitor.°° °°°°°°°°°°°°°°°°°°°°°°°°°°° 10 °°°°°°°°°°°°°°°°°°°°°°°°°°°°°° °°° °°° 10 °°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°° 10 °°°°°°°°°°°°°°°°°°°°°°°°°°°°° 11 °°°°°°°°°°°°°°°°°°°°°°°°°°° 11 °°°°°°°°°°°°°°°°°°°°°°°°°°°°°° 11 °°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°° 12 °°°°°°°°°°°°°°°°°°°°°°°°°°°° 12 °°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°° 13 °°°°°°°°°°°°°°°°°°°°°°°°°°° 13 °°°°°°°°°°°°°°°°° 15 Connecting Your LCD Monitor Plug & Play Warm-up Time 4. Adjusting The Monitor The Function Control Buttons How to use the Hot Key. Main OSD Menu BRIGHTNESS/CONTRAST COLOR POSITION &CLOCK/PHASE OSD MENU ADJUSTMENT & INPUT SOURCE SETUP MENU °°°°°°°°°°°°°°°°°°°°°°°°°°°° 15 5. Appendix °°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°° 16 °°° °°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°° 16 Specifications 15-pin D-Sub Connector °°°°°°°°°°°°°°°°°°°°°°°°°°°°°° 17 °°°°°°°°°°°°°°°°°°°°°°°°°°°° 18 DPMS Power Saving Mode 6. Troubleshooting °°°°°°°°°°°°°°°°°°°°°°°° °°°°°°° 19 1 Before setting up This is 15.0 inch TFT-LCD monitor. Before setting up the LCD Monitor, please read this manual to help your understanding of the LCD Monitor. Brief Specification of LCD Monitor ¡Ü Resolution : 15.0 inch XGA (1024 X 768@75Hz) ¡Ü Color display : 16,777,216 colors ¡Ü DPMS (Display Power Management Signaling) ¡Ü OSD (On Screen Display) ¡Ü Auto Configuration : Hot key ¡Ü DDC 1/2B : Plug & Play Notice According to PC system, DDC 1/2B may not be supported. If you meet Error message,check your video card which compatibility with DDC. If you eant to know more information, please contact our service center. Precautions Check the voltage corresponds to the local electrical supply before connecting the AC power cord. Do not use Ketone type material (ex. Acetone), Ethyl Alcohol, Toluene, Ethyl Acid or Methyl chloride, to clear the panel. It might permanently damage the panel. Never use the damaged AC power cord. Keeps it away from stoves, heaters, fireplaces and other sources of heat and magnets. Dont’ put your LCD monitor in a location with high humidity and dust. Temperature : 0~40°£ Humidity : 90% less Place the LCD monitor on a solid surface. If dropped, the screen can be damaged easily. Don’t touch the screen with a acute nail and pin The LCD monitor consists of electrical devices. If the LCD monitor is damaged, contact immediately our service center. The LCD monitor can be damaged easily by shock. If you don’t use the LCD monitor for a long time, unplug the LCD monitor. Don’t use your LCD monitor under direct sunlight. 2 Items User Manual LCD Monitor Power card, DC Adapter 15-pin D-Sub Signal Cable Notise Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. 3 Setting up the LCD monitor Where is a good place to position the monitor? Place the LCD monitor on a solid and flat surface. If dropped, the screen can be damaged easily. How to connect the power cord and the several cables to the LCD monitor. No. Name Cable connections DC12V DC Adaptor PC 15-pin D-Sub Signal Cable Plug & Play The adoption of the new VESA Plug and Play solution eliminates complicated and time consuming setup. It allows you to install your monitor in a Plug and Play compatible system without the usual hassles and confusion. Your PC system can easily identify and configure itself for use with your display. This monitor automatically tells the PC system its Extended Display Identification Data (EDID) using Display Data Channel (DDC) protocols so the PC system can automatically configure itself to use the flat panel display. Warm-up Time All LCD monitors need time to become thermally stable whenever you turn on the monitor after letting the monitor be turned off for a couple of hours. Therefore, to achieve more accurate adjustments for parameters, allow the LCD monitor to be warmed up for at least 20 minutes before making any screen adjustments. 10 4 Adjusting The Monitor The Function Control Buttons How to use the function Key. 1. First click : The OSD main menu appears. 2. Second click : The OSD menu disappears. 1. Select a command function. 2. When you push Auto button, this will optimize image quality automatically. Down : 1. Move the on-screen highlighted command item to the next one. 2. Decrease the current option value. UP : 1. Move the on-screen highlighted command item to the Previous one. 2. Increase the current option value. Power On/Off toggle button. 11 Main OSD Menu When you push the menu button, you can see below main OSD menu. MAIN MENU BRIGHTNESS/CONTRAST COLOR POSITION OSD SETUP EXIT 1024¡¿ 768 60.0KHz / 75Hz BRIGHTNESS/CONTRAST ¡Ü Brightness : Changes the overall light intensity of the images being displayed. ¡Ü Contrast : Changes the ratio of light intensity between the brightest white and darkest black. ¡Ü Gamma : Change the gamma value. MAIN MENU BRIGHTNESS/CONTRAST COLOR POSITION OSD SETUP EXIT 1024¡¿ 768 BRIGHTNESS / CONTRAST BRIGHTNESS ¢¸ §š§š§š§š§š§š§š§š ¡¦¡¦¡¦ ¢º50 CONTRAST ¢¸ §š§š§š§š§š§š§š§š ¡¦¡¦¡¦ ¢º GAMMA ¢¸ §š§š§š§š§š§š§š§š ¡¦¡¦¡¦ ¢º EXIT 60.0KHz / 75Hz Adjusting Gamma Value is useful in case of game or movie screen. Notice 12 COLOR ¡ÜThe tone of color can be changed form bluish white to reddish white. ¡ÜColor1 - Blue type ¡ÜColor2 - Red type ¡ÜRED, GREEN, BLUE - You can adjust red, green and blue values that you want. MAIN MENU BRIGHTNESS/CONTRAST COLOR POSITION OSD SETUP EXIT 1024¡¿ 768 60.0KHz / 75Hz COLOR COLOR1 COLOR2 RED ¢¸ §š§š§š§š§š§š§š§š ¡¦¡¦¡¦ ¢º50 GREEN ¢¸ §š§š§š§š§š§š§š§š ¡¦¡¦¡¦ ¢º BLUE ¢¸ §š§š§š§š§š§š§š§š ¡¦¡¦¡¦ ¢º EXIT POSITION & CLOCK/PHASE CLOCK/PHASE ¡Ü When image is not clear, you can use clock/phase menu. ¡Ü PHASE/ CLOCK : Although ‘Auto Adjustment’ automatically finds the optimum values of Clock and Phase parameters as well as image position, it may be necessary for you to adjust those parameters manually. It is recommended for you to use ‘Auto Adjustment’ first. If the adjustment results are not satisfactory, then use Clock and Phase adjustment features to get the best adjustment results. Bear in mind that Clock and Phase adjustment may change the width of the image and affect image position as well. If the image is clear while out of center by a couple of pixels, use image position to center the image. 13 MAIN MENU POSITION BRIGHTNESS/CONTRAST HORIZONTAL ¢¸ §š§š§š§š§š§š§š§š ¡¦¡¦¡¦ ¢º50 COLOR POSITION OSD SETUP EXIT 1024¡¿ 768 60.0KHz / 75Hz VERTICAL ¢¸ §š§š§š§š§š§š§š§š ¡¦¡¦¡¦ ¢º CLOCK ¢¸ §š§š§š§š§š§š§š§š ¡¦¡¦¡¦ ¢º PHASE ¢¸ §š§š§š§š§š§š§š§š ¡¦¡¦¡¦ ¢º EXIT POSITION ¡Ü Changes the location of the image. ¡Ü H-Position : Moves to the Left/Right ¡Ü V-Position : Moves to the Bottom/Top If image is not clear (noise), you can adjust Clock/Phase. Notice 14 OSD MENU ADJUSTMENT & INPUT SOURCE ¡Ü Sets the OSD menu display position. ¡Ü OSD Position : Moves the OSD menu to the horizontal or vertical direction. ¡Ü OSD TIME : Shows the OSD TIME displays from 5 to 60sec. ¡Ü LANGUAGE : Select language in OSD menu. MAIN MENU OSD BRIGHTNESS/CONTRAST OSD POSITION ¢º COLOR POSITION OSD TIME ¢º30 SEC LANGUAGE ¢ºENGLISH OSDT SETUP EXIT 1024¡¿ 768 EXIT 60.0KHz / 75Hz SETUP MENU ¡Ü White balance : Automatic djust color (white level) for various input source’s white level. ¡Ü Information : display monitor’s information. ¡Ü Recall : Discards current setting and replaced all paramotors with the factory default values. MAIN MENU SETUP BRIGHTNESS/CONTRAST AUTO BALANCE COLOR POSITION OSD INFORMATION RECALL SETUPT EXIT 1024¡¿ 768 EXIT 60.0KHz / 75Hz 15 5 Appendix Display Modes Mode Resolution 720 X 400 Horizontal Vertical Pixel Clock Sync Frequency(KHz) Frequency(Hz) Frequency(MHz) Polarity(H/V) 31.468 70.087 28.322 -/+ 31.468 59.940 25.175 -/- 35.000 66.670 30.240 -/- 37.500 75.000 31.500 -/- 37.879 60.300 40.000 +/+ 48.077 72.188 50.000 +/+ 46.875 75.000 49.500 +/+ 48.363 60.004 65.000 -/- 56.476 70.000 75.000 -/- 60.023 75.029 78.750 +/+ VGA 640 X 480 SVGA XGA 16 800 X 600 1024 X 768 15-pin D-Sub Connector ¡Ü Input signal : Analog RGB ¡Ü 15-pin D-Sub connector Pin No. Signal Name Pin No. Signal Name Pin No. Signal Name Analog Red Input Analog Red Ground 11 Ground Analog Green Input Analog Green Ground 12 DDC Data Analog Blue Input Analog Blue Ground 13 Horizontal Sync Ground No Connect 14 Vertical Sync DDC Ground 10 Sync Ground 15 DDC Clock 15pin D-Sub Signal Cable 17 DPMS Power Saving Mode This monitor has a built-in power management system called DPMS Power Saving Mode. This system saves energy by switching your monitor into a low-power mode when it has not been used for a certain period of time. The available modes are “ON”, “Standby”, “Suspend”, and “OFF”. H-sync Signal V-sync RGB ON Active Active Active Stanby mode Inactive Active Blanked State Stanby mode Active OFF Inactive 18 Inactive Inactive Blanked Blanked Power Recovery Consumption Time Under 30Watt LED Color and Operting status Green Alternating Green/Orange Less than 5Watt (0.5 Sec interval) Within 2Sec Alternating Green/Orange (1 Sec interval) Orange 6 Troubleshooting What you see Suggested Actions Screen is blank and power indictor is off Ensure that the power cord is firmly connected and the LCD monitor is on. “out of range” message ¦U Check the maximum resolution and the frequency of the video adaptor. ¦U Compare these values with the data in the Display Modes Timing Chart. “No signal input” message ¦U Ensure that the signal cable is firmly connected to the PC or video sources. ¦U Ensure that the PC or video sources are turned on. Image is not stable and may appear to vibrate ¦U Check that the display resolution and frequency from your PC or video board is an available mode for your monitor. On your computer check : Control Panel, Display, Settings ¦U Note : Your monitor supports multiscan display functions within the following frequency domain: The image is too light or too dark ¦U Adjust the Brightness and Contrast. ¦U Refer to the Brightness/Contrast The image color is not good Image is not centered on the screen Screen is blank and power indicator light is steady amber or blinks every 0.5 or 1 seconds ¦U Adjust the Color ¦U Refer to the Color ¦U Executes Auto Configuration. ¦U The monitor is using its power management system. ¦U M ove the computer’s mouse or press a key on the keyboard. 19 20 Appendix A. Specifications Type Size Panel Display Resolution Frequency TFT active matrix 15 inch 304.1¡¿ 228.1(mm) Pixel Pitch 0.297¡¿ 0.297(mm) Display Color 8-bit (16,777,216 colors) Basic 1 0 2 4¡¿ 768@60Hz Maximum 1024¡¿ 768@75Hz Horizontal 31.5~60KHz Vertical 56~75Hz Sync Signal TTL, P. or N. Tilting Degree (U/D) -5¡Æ ~30¡Æ Degree Plug&Play VESA DDC 1/2B Power Input 90~265VAC Output Adapter DC 12V, 4.16A Consumption Under 30W Standby mode 5W less Power Management VESA DPMS Environmental Consideration Temperature 0~40¡Æ C (32¡Æ F~104¡Æ F) Humidity 90% less Dimensions Outside 362mm(W)¡¿ 345mm(D)¡¿ 268mm(H) Monitor 3.2kg Carton 1.4kg Weight ¡Ø The specification of this monitor is subject to be changed without notice to improve performance.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : No Create Date : 2002:09:06 14:44:00Z Subject : Modify Date : 2003:02:11 17:38:25+09:00 Page Count : 23 Creation Date : 2002:09:06 14:44:00Z Author : 2 Producer : Acrobat PDFWriter 3.0.1 for Power Macintosh Keywords : Mod Date : 2002:10:10 15:48:05+09:00 Metadata Date : 2002:10:10 15:48:05+09:00 Title : Creator : 2 Description : Has XFA : NoEXIF Metadata provided by EXIF.tools