Wooyoung Telecom HL700M LCD Monitor User Manual HL700A M17
Wooyoung Telecom Co., Ltd. LCD Monitor HL700A M17
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 307255 |
| Application ID | ya9UIuXQkq6hWQPWdlgyCQ== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 71.14kB (889263 bits) |
| Date Submitted | 2003-03-04 00:00:00 |
| Date Available | 2003-03-04 00:00:00 |
| Creation Date | 2003-01-24 01:28:54 |
| Producing Software | Acrobat Distiller 5.0.5 for Macintosh |
| Document Lastmod | 2003-02-13 17:01:07 |
| Document Title | HL700A,M17 (....)-.... |
| Document Creator | QuarkXPress3.3k: AdobePS 8.7.3 (301) |
User’s Reference WOO YOUNG Telecom CO.,LTD. FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, with can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. - Only shielded interface cable should be used. Finally, any changes or modifications to the equipment by the user not expressly approved by the grantee or manufacturer could void the users authority to operate such equipment. Appendix A. Specifications Type Panel Size Pixel Pitch Display Color Basic Display Resolution Maximum Horizontal Frequency Vertical Sync Signal Connectors Tilting Degree (U/D) Plug&Play Input Output Power Consumption Standby mode Power Management Temperature Environmental Consideration Humidity Outside Dimensions Monitor Weight Carton TFT active matrix 17 inch 337.92mm 270.336mm 0.264mm 0.264mm 8-bit (16,777,216 colors) 1280 1024@60Hz 1280 1024@75Hz 31.5~80KHz 56~75Hz TTL, P. or N. D-Sub 15pin connector Speaker Input / Headphone Output (Audio Cable) 24pin Digital Cable Audio Cable RCA Cable S-Video Cable External TV Box(HL700MT Only) -3 ~20 Degree VESA DDC 1/2B 90~265VAC Adapter DC 12V, 4.16A VESA DPMS 0~40 C (32 F~104 F) 90% less 416mm(W) 409mm(H) 186mm(D) 5.2kg 3kg The specification of this monitor is subject to be changed without notice to improve performance. Contents 1. Before Setting up Brief Specification of LCD Monitor In multimedia Model, added the below functions Precautions 2. Items 3. Setting up the LCD monitor Where is a good place to position the monitor? Check before connecting the power cord and the signal cable !! Monitor’s connectors (HL700A) Monitor’s connectors (HL700M / MT) 10 Connecting Your LCD Monitor 11 Plug & Play 12 Warm-up Time 12 4. Adjusting The Monitor 13 The Function Control Buttons (HL700A) 13 How to use the Hot Key. (HL700A) 13 The Function Control Buttons (HL700M / MT) 14 How to use the Hot Key. (HL700M / MT) 14 Main OSD Menu 15 BRIGHTNESS/CONTRAST 15 POSITION &CLOCK/PHASE 16 COLOR 17 OSD MENU ADJUSTMENT & INPUT SOURCE 17 SETUP MENU 18 Input Source 18 Video1, Video2 19 5. Appendix 20 Appendix A. Specifications 20 Appendix B. 15-pin D-Sub Connector 21 Appendix C. 24-pin DVI Connector 22 Appendix D. DPMS Power Saving Mode 23 6. Troubleshooting 24 1 Before setting up This is 17.0 inch TFT-LCD monitor. Before setting up the LCD Monitor, please read this manual to help your understanding of the LCD Monitor. Brief Specification of LCD Monitor Resolution : 17.0 inch SXGA (1280 X 1024@75Hz) Color display : 16,777,216 colors DPMS (Display Power Management Signaling) OSD (On Screen Display) Auto Configuration : Hot key Speaker [L + R : 3W + 3W = 6W (max)] DDC 1/2B : Plug & Play In Multimedia Model, added the below function: DVI(Digital Video Interface) Composit video input Composit Audio input S-Video input TV(HL700MT Only) Notice According to PC system, DDC 1/2B may not be supported. If you meet Error message,check your video card which compatibility with DDC. If you eant to know more information, please contact our service center. Precautions 90V~265V Check the voltage corresponds to the local electrical supply before connecting the AC power cord. Do not use Ketone type material (ex. Acetone), Ethyl Alcohol, Toluene, Ethyl Acid or Methyl chloride, to clear the panel. It might permanently damage the panel. Never use the damaged AC power cord. Keeps it away from stoves, heaters, fireplaces and other sources of heat and magnets. Don’t put your LCD monitor in a location with high humidity and dust. Temperature : 0~40。C Humidity : 90% less Place the LCD monitor on a solid surface. If dropped, the screen can be damaged easily. Don’t touch the screen with a acute nail and pin The LCD monitor consists of electrical devices. If the LCD monitor is damaged, contact immediately our service center. The LCD monitor can be damaged easily by shock. If you don’t use the LCD monitor for a long time, unplug the LCD monitor. Don’t use your LCD monitor under direct sunlight. 2 Items User Manual LCD Monitor How to fold stand Notice If you need to fold stand for movimg. please refer to the below picture. To fold stand, you must down lever, and you can fold stand. 15-pin D-Sub Signal Cable Audio Cable RCA Cable S-Video Cable 24pin Digital Cable(Option) External TV Box (HL700MT Only) DC Adapter Notice Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. 3 Setting up the LCD monitor Where is a good place to position the monitor? Place the LCD monitor on a solid and flat surface. If dropped, the screen can be damaged easily. Check before connecting the power cord and the signal cable !! Turn off the PC power before connecting the power cord and signal cable to the LCD monitor. Monitor’s connectors (HL700A) Name No. Cable connections PC 15-pin D-Sub Signal Cable DC12V DC Adaptor PC AUDIO IN Audio Cable SPK OUT External Speaker Monitor’s connectors (HL700A) PC No. Name Cable connections VIDEO No. Name Cable connections DVI Digital Video Cable(option) AUDIO(R) Audio output(R) (Red) PC 15-pin D-Sub Signal Cable AUDIO(L) Audio output(L) (White) DC12V DC Adapter VIDEO1 DVD/VCR Cable (Yellow) PC AUDIO IN Speaker Cable Ext. External TV Box (HL700MT Only) SPK OUT 10 VIDEO2 S-Videl Cable 10 External Speaker Cable Connecting Your LCD Monitor For HL700A Connecting your PC system 1. Connect the 15-pin D-Sub Signal Cable from PC to No.1. 2. If you use a speaker, connect the Audio Cable from PC to No.3. 3. If you use a headphone and earphone, connect the Headphone Cable from PC to No.4. For HL700M /MT Connecting your PC system 1. Connect the 15-pin D-Sub Signal Cable from PC to No.2. 2. If you have a DVI compliant video graphics adaptor, connect Digital Video Cable from PC to No.1. 3. If you use a speaker, connect the Audio Cable from PC to No.4. 4. If you use a headphone and earphone, connect the Headphone Cable from PC to No.5. Connecting your AV(DVD, VIDEO, CAMCODER) & TV 1. Connect the DVD/VCR Cable from PC to No.6, No.7 and No.8. 2. Connect the external TV box cable to NO.9. 3. Connect the S-Video cable to NO.10. FCC RF INTERFERENCE STATEMENT NOTE : This equipment tas been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment renerates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to redio commuications. Operation of this equipment in a residential area is likely to cause hamful interference in which case the will be required to correct the interference at his own expense. 11 Connecting for TV Connect the external TV Box to Monitors Ext. jack Connect the antenna cable to the external TV Box from wall antenna jack same as the below the picture Plug & Play The adoption of the new VESA Plug and Play solution eliminates complicated and time consuming setup. It allows you to install your monitor in a Plug and Play compatible system without the usual hassles and confusion. Your PC system can easily identify and configure itself for use with your display. This monitor automatically tells the PC system its Extended Display Identification Data (EDID) using Display Data Channel (DDC) protocols so the PC system can automatically configure itself to use the flat panel display. Warm-up Time All LCD monitors need time to become thermally stable whenever you turn on the monitor after letting the monitor be turned off for a couple of hours. Therefore, to achieve more accurate adjustments for parameters, allow the LCD monitor to be warmed up for at least 20 minutes before making any screen adjustments. 12 4 Adjusting The Monitor The Function Control Buttons (HL700A) MUTE AUTO MENU SELECT VOLUME How to use the Hot Key. (HL700A) MUTE Sound Mute On/Off button. When you push Auto button, this will optimize image quality automatically. AUTO OSD menu On/Off button. MENU SELECT Menu select button. Power On/Off toggle button. You can adjust brightness or contrast as not key. When display adjust menu, you can adjust with Left/Right button arrow button. VOLUME When you push the Left/Right button, you can adjust the volume. 13 The Function Control Buttons (HL700M / MT) MUTE AUTO/SELECT MENU MODE VOLUME How to use the Hot Key. (HL700M / MT) Sound Mute On/Off button. MUTE AUTO/SELECT When you push Auto button, this will optimize image quality automatically. Notice : In MENU, the button is“SELECT”function MENU OSD menu On/Off button. MODE Menu select button. Power On/Off toggle button. You can adjust brightness or contrast as not key. When display adjust menu, you can adjust with Left/Right button arrow button. Notice : VOLUME 14 When you push the Left/Right button, you can adjust the volume. Main OSD Menu When you push the menu button, you can see below main OSD menu. MAIN MENU BRIGHTNESS/CONTRAST COLOR POSITION OSD SETUP EXIT BRIGHTNESS/CONTRAST Brightness : Changes the overall light intensity of the images being displayed. Contrast : Changes the ratio of light intensity between the brightest white and darkest black. You can adjust brightness/contrast values that you want by this hot key. Gamma : Change the gamma value. MAIN MENU BRIGHTNESS/CONTRAST COLOR POSITION OSD SETUP EXIT BRIGHTNESS / CONTRAST BRIGHTNESS 50 CONTRAST GAMMA EXIT Adjusting Gamma Value is useful in case of game or movie screen. Notice 15 POSITION & CLOCK/PHASE CLOCK/PHASE When image is not clear, you can use clock/phase menu. PHASE/ CLOCK : Although ‘Auto Adjustment’ automatically finds the optimum values of Clock and Phase parameters as well as image position, it may be necessary for you to adjust those parameters manually. It is recommended for you to use ‘Auto Adjustment’ first. If the adjustment results are not satisfactory, then use Clock and Phase adjustment features to get the best adjustment results. Bear in mind that Clock and Phase adjustment may change the width of the image and affect image position as well. If the image is clear while out of center by a couple of pixels, use image position to center the image. MAIN MENU BRIGHTNESS/CONTRAST COLOR POSITION OSD SETUP EXIT POSITION HORIZONTAL VERTICAL CLOCK PHASE EXIT POSITION Changes the location of the image. H-Position : Moves to the Left/Right V-Position : Moves to the Bottom/Top If image is not clear (noise), you can adjust Clock/Phase. Notice 16 50 COLOR The tone of color can be changed form bluish white to reddish white. Color1 - Blue type Color2 - Red type RED, GREEN, BLUE - You can adjust red, green and blue values that you want. MAIN MENU BRIGHTNESS/CONTRAST COLOR POSITION OSD SETUP EXIT COLOR COLOR1 COLOR2 RED 50 GREEN BLUE EXIT OSD MENU ADJUSTMENT & INPUT SOURCE Sets the OSD menu display position. OSD Position : Moves the OSD menu to the horizontal or vertical direction. OSD TIME : Shows the OSD TIME displays from 5 to 60sec. LANGUAGE : Select language in OSD menu. MAIN MENU OSD BRIGHTNESS/CONTRAST OSD POSITION COLOR POSITION OSD TIME 30 SEC LANGUAGE ENGLISH OSDT SETUP EXIT EXIT 17 SETUP MENU Auto balance : Automatic adjust color (white level) for various input source’s white level. Input source : display input signal. Information : display monitor’s information. Recall : Discards current setting and replaced all paramotors with the factory default values. MAIN MENU BRIGHTNESS/CONTRAST COLOR POSITION OSD SETUPT EXIT SETUP AUTO BALANCE SELECT INPUT SOURCE PC INFORMATION SELECT RECALL SELECT EXIT Input Source (HL700M / MT) INPUT SOURCE : Selects input signal. (PC DIGITAL VIDEO1 VIDEO2 TV) The mode button can adjust Input Source by hot key. Notice 18 In this case, the mode change time spend 2~3sec. VIDEO1, VIDEO2 (HL700M / MT) MAIN MENU MAIN MENU BRIGHTNESS / CONTRAST COLOR CHANNEL SETUP EXIT BRIGHTNESS / CONTRAST : Increase or decreases the light intensity of the screen / increase or decrease the ratio of the light intensity between the brightest white and the darkest black. COLOR : Refer to below color menu. CHANNEL : Refer to below channel menu. (TV installation) SETUP : Refer to OSD menu adjustment. EXIT : Finish the current status. COLOR COLOR SHARPNESS COLOR TINT SHARPNESS : Make image of the VIDEO/TV looked sharper. COLOR : Adjust color intensity of the VIDEO/TV. TINT : Adjust a color tone of the VIDEO/TV. SETUP : Refer to OSD menu adjustment. EXIT CHANNEL CHANNEL AIR/CATV AUTO CHANNEL MANUAL CHANNEL EXIT AIR/CATV : Select AIR or CATV. AUTO CHANNEL : Search the channel automatically. (SELECT button button : select channel SELECT button (ADD/DEL)) MANUAL CHANNEL : Search the channel manually. FINE : Adjust image quality of the TV. The mode button can adjust Input Source by hot key. Notice In this case, the mode change time spend 2~3sec. 19 5 Appendix Appendix A. Display Modes Mode Resolution 720 X 400 VGA SVGA XGA SXGA 20 640 X 480 800 X 600 1024 X 768 1280 X 1024 Horizontal Vertical Pixel Clock Sync Frequency(KHz) Frequency(Hz) Frequency(MHz) Polarity(H/V) 31.468 70.087 28.322 -/+ 31.468 59.940 25.175 -/- 35.000 66.670 30.240 -/- 37.500 75.000 31.500 -/- 37.879 60.300 40.000 +/+ 48.077 72.188 50.000 +/+ 46.875 75.000 49.500 +/+ 48.363 60.004 65.000 -/- 56.476 70.000 75.000 -/- 60.023 75.029 78.750 +/+ Appendix B. 15-pin D-Sub Connector Input signal : Analog RGB 15-pin D-Sub connector Pin No. Signal Name Pin No. Signal Name Pin No. Signal Name Analog Red Input Analog Red Ground 11 Ground Analog Green Input Analog Green Ground 12 DDC Data Analog Blue Input Analog Blue Ground 13 Horizontal Sync Ground No Connect 14 Vertical Sync DDC Ground 10 Sync Ground 15 DDC Clock 15pin D-Sub Signal Cable 21 Appendix C. 24-pin DVI Connector Input signal : Digital 24-pin DVI connector Pin No. Signal Name Pin No. Signal Name Signal Name TMDS DATA2- TMDS DATA1- TMDS DATA- TMDS DATA2+ TMDS DATA1+ TMDS DATA+ DGND DGND DGND NC NC NC NC NC NC DDC CLOCk +5V POWER DGND DDC DATA AGND TMDS CLOCK+ Analog vertical Sync NC TMDS CLOCK- 24pin Digital Cable 22 Pin No. Appendix D. DPMS Power Saving Mode This monitor has a built-in power management system called DPMS Power Saving Mode. This system saves energy by switching your monitor into a low-power mode when it has not been used for a certain period of time. The available modes are “ON”, “Standby”, “Suspend”, and “OFF”. H-sync Signal V-sync RGB ON Active Active Active Stanby mode Inactive Active Blanked Stanby mode Active Inactive Blanked OFF Inactive Inactive Blanked State Power Recovery Consumption Time Under 40Watt LED Color and Operting status Green Amber Less than 5Watt Within 2Sec Amber Amber 23 6 Troubleshooting What you see Screen is blank and power indictor is off. “out of range” message. Suggested Actions Ensure that the power cord is firmly connected and the LCD monitor is on. Check the maximum resolution and the frequency of the video adaptor. Compare these values with the data in the Display Modes Timing Chart. “No signal input” message. Ensure that the signal cable is firmly connected to the PC or video sources. Ensure that the PC or video sources are turned on. Image is not stable and may appear to vibrate. Check that the display resolution and frequency from your PC or video board is an available mode for your monitor. On your computer check : Control Panel, Display, Settings Note : Your monitor supports multiscan display functions within the following frequency domain: Horizontal frequency : 31~80KHz Vertical frequency : 56~75Hz Maximum refresh rate : 1280 x 1024 @75Hz The image is too light or too dark. Adjust the Brightness and Contrast. Refer to the Brightness/Contrast The image color is not good. Image is not centered on the screen. Screen is blank and power indicator light is steady amber or blinks. 24 Adjust the Color Refer to the Color Executes Auto Configuration. The monitor is using its power management system. Move the computer’s mouse or press a key on the keyboard. WOO YOUNG Telecom CO.,LTD. http://www.wyt.co.kr P/N : 97E9500117
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Create Date : 2003:01:24 01:28:54Z Modify Date : 2003:02:13 17:01:07+09:00 Page Count : 28 Creation Date : 2003:01:24 01:28:54Z Mod Date : 2003:01:29 09:57:54+09:00 Producer : Acrobat Distiller 5.0.5 for Macintosh Author : Metadata Date : 2003:01:29 09:57:54+09:00 Creator : Title : HL700A,M17 (....)-.... Has XFA : NoEXIF Metadata provided by EXIF.tools