Wuerth Elektronik eiSos and Co KG F162000010 KaVo Radio 2.4 GHz Transceiver Module User Manual

AMBER Wireless GmbH KaVo Radio 2.4 GHz Transceiver Module

User Manual

Annex No.5 Technical Description Users Manual
User instructionsERGOcom 3Always on the safe side.
Vertrieb / Distribution:KaVo Dental GmbH & Co. KGBahnhofstraße 20D-88447 WarthausenTel.: ++ 49 / 73 51 / 56 - 0Fax: ++ 49 / 73 51 / 56 16 27Hersteller / Manufacturer:Kaltenbach & Voigt GmbH & Co. KGBismarckring 39D-88400 Biberach
ERGOcom 3Table of contentsTable of contentsTable of contents ............................................................................................................................................3 1 User Notes ....................................................................................................................................................5 1.1 User guidelines ........................................................................................................................................5 1.1.1 Abbreviations ..................................................................................................................................5 1.1.2 .........................................................................................................................................................5 1.2 Target audience .......................................................................................................................................6 1.3 Service .....................................................................................................................................................7 1.4 Provisions of guarantee ...........................................................................................................................8 1.5 Transport and storage ..............................................................................................................................9 1.5.1 The German packaging ordinance, 28 August 1998 ......................................................................9 1.5.2 Damage in transit ............................................................................................................................9 1.5.3 Storage .........................................................................................................................................10 2 Safety ..........................................................................................................................................................12 2.1 Description of safety instructions ...........................................................................................................12 2.1.1 Hazard warning symbol ................................................................................................................12 2.1.2 Structure .......................................................................................................................................12 2.1.3 Description of the different levels of hazard ..................................................................................12 2.2 Intended purpose ...................................................................................................................................13 2.2.1 General .........................................................................................................................................13 2.2.2 Product-specific ............................................................................................................................13 2.3 Safety instructions ..................................................................................................................................14 2.3.1 General .........................................................................................................................................14 2.3.2 Product-specific ............................................................................................................................14 3 Product description ...................................................................................................................................15 3.1 Product name .........................................................................................................................................15 3.2 ERGOcom 3 ...........................................................................................................................................16 3.3 Connections ...........................................................................................................................................17 3.4 Rating plate ............................................................................................................................................18 3.5 Technical data ........................................................................................................................................19 4 Start-up .......................................................................................................................................................20 4.1 Start-up ..................................................................................................................................................20 4.1.1 Start-up .........................................................................................................................................20 4.1.2 Start-up, radio receiving ................................................................................................................20 4.1.3 Start-up, USB drive .......................................................................................................................21 5 Operation ....................................................................................................................................................24 5.1 Operation, general .................................................................................................................................24 5.1.1 Switch on ......................................................................................................................................24 5.1.2 Standby .........................................................................................................................................24 5.1.3 OSD menu, call ERGOcom 3 .......................................................................................................24 5.1.4 OSD menu, operate ERGOcom 3 .................................................................................................25 5.1.5 Menu points ..................................................................................................................................25 5.2 Operation, no display interface (classic) ................................................................................................27 5.2.1 Operational mode .........................................................................................................................27 5.2.2 VGA OUT - set image source .......................................................................................................29 5.2.3 VIDEO OUT 1 - set image source .................................................................................................30 5.2.4 VIDEO OUT 2 - set image source .................................................................................................32 5.2.5 Generate still .................................................................................................................................33 5.2.6 Save still ........................................................................................................................................33 5.2.7 Audio signals .................................................................................................................................343/56
ERGOcom 3Table of contents 5.3 Operation, with display interface (comfort/excellence) ..........................................................................35 5.3.1 Operational mode .........................................................................................................................35 5.3.2 VGA OUT - set image source .......................................................................................................37 5.3.3 VIDEO OUT 1 - set image source .................................................................................................38 5.3.4 VIDEO OUT 2 - set image source .................................................................................................40 5.3.5 Audio signals .................................................................................................................................41 5.3.6 Generate still .................................................................................................................................41 5.3.7 Save still ........................................................................................................................................42 5.3.8 Change display view .....................................................................................................................42 5.3.9 Select image .................................................................................................................................43 5.3.10 Delete image / images ................................................................................................................44 5.3.11 Change image source .................................................................................................................45 5.4 Operation, OSD menu display interface ................................................................................................46 5.4.1 Call OSD menu display interface ..................................................................................................46 5.4.2 Operate OSD menu display interface ...........................................................................................46 5.4.3 VGA main menu ............................................................................................................................47 5.4.4 VIDEO main menu ........................................................................................................................48 5.4.5 Menu point, other ..........................................................................................................................49 6 Preparation methods DIN EN ISO 17664 ..................................................................................................51 6.1 Cleaning .................................................................................................................................................51 6.1.1 Exterior cleaning by hand .............................................................................................................51 6.2 Disinfection ............................................................................................................................................52 6.3 Maintenance ..........................................................................................................................................53 7 Safety checks .............................................................................................................................................54 8 Troubleshooting .........................................................................................................................................55 9 Glossary ......................................................................................................................................................56 4/56
ERGOcom 31 User Notes | 1.1 User guidelines1 User Notes1.1 User guidelinesPrerequisitePlease read these instructions before using the product to avoid operator error anddamage.1.1.1 AbbreviationsAbbre-viationMeaningUI User instructionsSI Setup instructionsEI Engineer's instructionsSFC Safety checksIEC International Electrotechnical Commission1.1.25/56
ERGOcom 31 User Notes | 1.2 Target audience1.2 Target audienceThis document is intended for use by dentists and other dental practice employees.6/56
ERGOcom 31 User Notes | 1.3 Service1.3 ServicePlease send all questions about the product, services and maintenance to the fol-lowing addresses.Always quote product serial number in any correspondence.KaVo Dental GmbH & Co. KGAfter Sales ServiceBahnhofstraße 20D-88445 Warthausen07351-56 270007351-18218kunden-service@kavo.dewww.kavo.comKaVo Präsentations- und Servicezentrum Frankfurt (KaVo Presentation andService Center, Frankfurt)Hungener Straße 6-1260389 Frankfurt069 - 5 97 03 -94 / 95KaVo Präsentations- und Servicezentrum Hamburg (KaVo Presentation andService Center, Hamburg)Sachsenstraße 520097 Hamburg040 - 23 44 -77/ - 78KaVo Präsentations- und Servicezentrum Düsseldorf (KaVo Presentation andService Center, Düsseldorf)Kaiserswerther Straße 3540477 Düsseldorf0211 - 49 91 -38 / -39KaVo Präsentations- und Servicezentrum Berlin (KaVo Presentation and Ser-vice Center, Berlin)Uhlandstraße 20-2510623 Berlin030 - 7 91 94 84KaVo Präsentations- und Servicezentrum Leipzig-Gerichshain (KaVo Presen-tation and Service Center, Leipzig-Gerichshain)Zweenfurther Straße 904827 Leipzig-Gerichshain03 42 92 - 7 41 -12/ -137/56
ERGOcom 31 User Notes | 1.4 Provisions of guarantee1.4 Provisions of guaranteeThe KaVo end customer guarantee for the product named in the completion certi-ficate guarantees that the product functions correctly and that there are no faults inthe material or workmanship for a duration of 12 months following the purchase date,according to the following conditions:Following a reasonable complaint relating to defects or short delivery,KaVo gua-rantee to provide a replacement or perform repairs, whichever they deem mostsuitable. Claims of any other nature, damages in particular, are excluded. In caseof default and gross negligence or intent, the latter only applies if there are no com-pelling legal provisions opposing it.KaVo shall not be liable for defects and their consequences, which occur as a resultofnormal wear and tear, or of improper cleaning or maintenance.Non-observance of the operating, maintenance or connection regulations; calcina-tion or corrosion; impurities in the air and water supply; or chemical or electricaleffects, which are non-standard or not permitted according to company regulations.As a general rule, this guarantee does not apply to lamps, glassware, rubber partsor the colour durability of synthetic materials.KaVo shall not be liable for defects or their consequences if they are likely to be adirect result of actions or modifications by a customer or third party.Any claims arising from this guarantee can only be lodged if the completion certifi-cate (carbon copy) has been sent in to KaVo and the operator/user is able to producethe original.8/56
ERGOcom 31 User Notes | 1.5 Transport and storage1.5 Transport and storage1.5.1 The German packaging ordinance, 28 August 1998NoteApplies only to the Federal Republic of Germany.KaVo transport packaging is disposed of and recycled by local waste managementand recycling companies under Germany's Dual System.For more information about waste management and recycling, and for up-to-datelists of local waste management and recycling companies, visit the following sites:http://www.umweltdatenbank.dehttp://www.quality.deAnyKaVo transport packaging that customers return to KaVo, at the customer's ownexpense, shall be forwarded to the appropriate recycling companies at no extra costand with no reimbursement.1.5.2 Damage in transitWithin GermanyIf the outer packaging is noticeably damaged upon delivery, the following proceduremust be adhered to:1. The recipient must record the loss or damage on the notice of receipt. The reci-pient and transport company employee delivering the product must both sign thenotice of receipt.2. Leave the product and packaging in the condition they arrived in.3. Do not use the product.4. Report the damage to the transport company.5. Report the damage to KaVo.6. Under no circumstances should you return the damaged product to KaVo withoutprior consultation.7. Send the signed notice of receipt to KaVo.If the product is damaged without there being any noticeable damage to the packa-ging upon delivery, you must proceed as follows:1. As soon as possible within 7 days of delivery,report the damage to the transportcompany.2. Report the damage to KaVo.3. Leave the product and packaging in the condition they arrived in.4. Do not use the damaged product.NoteIf the recipient fails to adhere to any of the procedures mentioned above, the da-mage shall be considered as having arisen after delivery(pursuant to Germany'sGeneral Terms and Conditions for Carriers (ADSp.), Article 28).9/56
ERGOcom 31 User Notes | 1.5 Transport and storageOutside GermanyNoteKaVo shall not be liable for damage caused in transit.Check the shipment immediately upon delivery!If the outer packaging is noticeably damaged upon delivery, the following proceduremust be adhered to:1. The recipient must record the loss or damage on the notice of receipt. The reci-pient and transport company employee delivering the product must both sign thenotice of receipt.The recipient may claim damages against the transport company only on thebasis of these recorded facts.2. Leave the product and packaging in the condition they arrived in.3. Do not use the product.If the product is damaged without there being any noticeable damage to the packa-ging upon delivery, you must proceed as follows:1. As soon as possible within 7 days of delivery,report the damage to the transportcompany.2. Leave the product and packaging in the condition they arrived in.3. Do not use the damaged product.NoteIf the recipient fails to adhere to any of the procedures mentioned above, the da-mage shall be considered as having arisen after delivery(pursuant to theConvention on the Contract for the International Carriage of Goods by Road (CMR)Chapter V Article 30).1.5.3 StorageNoteSave packaging in case product requires sending away for servicing or repairs..The symbols printed on the outer packaging apply to transportation and storage;their meanings are as follows:Keep upright in transit; this way up!Handle with careKeep dry10/56
ERGOcom 31 User Notes | 1.5 Transport and storageStacking limitation.Temperature limitations.11/56
ERGOcom 32 Safety | 2.1 Description of safety instructions2 Safety2.1 Description of safety instructions2.1.1 Hazard warning symbolHazard warning symbol2.1.2 StructureDANGERThe introduction describes the type and source of the danger.This section shows what could happen if the instructions are not followed.▶ The optional action shows what measures to take to avoid danger.2.1.3 Description of the different levels of hazardTo avoid personal and material injury, safety instructions within this document areclassified into three levels of hazard.CAUTIONCAUTIONIndicates a potentially dangerous situation which could result in material damage,minor personal injury or non-severe personal injury.WARNINGWARNINGIndicates a potentially dangerous situation which could result in fatal injury or se-vere personal injury.DANGERDANGERThis is the highest level of hazard. It indicates an imminently dangerous situationwhich could result in fatal injury or severe personal injury.12/56
ERGOcom 32 Safety | 2.2 Intended purpose2.2 Intended purpose2.2.1 GeneralThe operator is required to make sure that the device is in a fully functional and safecondition before commencing use.During use, the handler must comply with state stipulations; in particular:▪ the industrial safety regulations that are in place.▪ the regulations that are in place for the prevention of industrial accidents.The appropriate, comprehensive guidelines for this product and/or national laws,national regulations and technlogical rules for starting up and operating have to beapplied and fulfilled in line with the specified, intended purpose of the KaVo product.NoteIt is mandatory that country-specific regulations be adhered to during final decom-missioning of the KaVo product.Should you have any questions relating to the proper disposal of the KaVo product,please contact your nearestKaVo office.2.2.2 Product-specificTheERGOcom 3 shows the multimedia content of external image and audiosources.In a dental practice outside of the patient environment and together withaKaVo Display , it corresponds to a medical product of protection class 1.13/56
ERGOcom 32 Safety | 2.3 Safety instructions2.3 Safety instructions2.3.1 GeneralWARNINGInjuries or harm caused by damaged functional componentsDamaged functional components can cause personal harm or injury.▶ If functional components are damaged: Stop work,remedythe problem or informthe service engineer.CAUTIONMalfunction due to electromagnetic fieldsThis product meets all the requirements that are in effect relating to electromagneticfields. Due to the complex interference between mobile phones and medical devi-ces, it is not, however, possible to completely exclude the possibility of the productbeing affected by a functioning mobile phone.▶ Refrain from using mobile phones in the practice and clinic area!▶ Turn off electronic equipment, such as data storage, hearing aids etc, du-ringoperation !CAUTIONRisks caused by electromagnetic fieldsElectromagnetic fields may interfere with the functions of implanted systems (suchas pacemakers).▶ Consult the patient before treatment!This KaVo product is not permitted for use in areas where there is a risk of explosion.The following individuals are authorised to repair and maintain the KaVo product:▪ Engineers from KaVo offices.▪ Engineers working for KaVo authorised dealers, specially trained by KaVo.▪ Independent engineers specially trained by KaVo.2.3.2 Product-specificCAUTIONRisk of injury due to electric shockElectric shock▶Remove bus covers only when ERGOcom 3 is switched off.▶ Check the additionally connected cable at earthing connection M . R = < 0.1 Ohm▶ Observe standards EN 60601-1-1, IEC 950, EN 550022 and EN 550024 incombination with compatible displays.▶ In the case of installation in rooms used for medical purposes, this must bedesigned in accordance with DIN/VDE 0100-710 (erection of low voltagesystems).▪ Do not place any additional portable multiple sockets on the floor.▪ Do not connect any additional portable multiple sockets or extension cables tothe system.▪ Do not connect any electrical equipment that is not part of the system.14/56
ERGOcom 33 Product description | 3.1 Product name3 Product description3.1 Product nameERGOcom 3 is supplied in classic, comfort and excellence models. These modelsdiffer with regard to the components built in, among other things.Model Componentsclassic No display interfaceNo radio master (ERGOremote)comfort With display interfaceNo radio master (ERGOremote)excellence With display interfaceWith radio master (ERGOremote)Every component can be individually upgraded. This is why operation is structurednot by the models, but by the integrated components.15/56
ERGOcom 33 Product description | 3.2 ERGOcom 33.2 ERGOcom 31Main switch10Navigation up2Standby LED, blue11Navigation right3Standby12Navigation down4Button, VGA In 1 / In 213Delete image / images5Button, Video Camera / In 2 / In 314Freeze6Status display15Button, Video Out 27OSD menu16Button, Video Out 18Quad mode17Button, VGA Out9Navigation left18Channel Selection/Learn ChannelMode16/56
ERGOcom 33 Product description | 3.3 Connections3.3 Connections1Audio In 113Aerial connection2Video In 114Mains connection3Audio In 215Mains fuse4Video In 216Power supply, monitor5Audio Out 117Display 1 connection6Video Out 118Camera connection7Audio Out 219USB downstream8Video Out 220USB upstream9Audio VGA In 121Camera cradle / footswitch control,Video In 110Audio VGA In 222VGA Out11Audio VGA Out23VGA In 212Earthing point24VGA In 117/56
ERGOcom 33 Product description | 3.4 Rating plate3.4 Rating plateSN: Serial numberREF Material numberType: Device typeERGOcom 3HF emissionNote: consult accompanying documents.VDE identificationCE identificationConsult instructions for useCSA identification18/56
ERGOcom 33 Product description | 3.5 Technical data3.5 Technical dataERGOcom 3Weight 3 kgHousing dimensionsWidth 260 mmDepth 260 mmHeight 46.5 mmElectricity supplyAC voltage 100 -240 VRated frequency 50 - 60 HzPower consumption 70 VAAmbient conditionsPermissible operating temperature 0 - 40° CConnection of interoral cameraType BFCompatible displaysMax. power consumption 35 VA19/56
ERGOcom 34 Start-up | 4.1 Start-up4 Start-up4.1 Start-up4.1.1 Start-upCAUTIONMalfunction due to incorrect useAn increase in operating temperature due to poor ventilation can lead to malfunc-tion or failure.▶ Do not set up near to a heat source.▶ Do not cover the product's vents. A minimum gap of 50 mm must be left in frontof and behind the unit.▶ Operate the product only when it is horizontal.▶Connect theERGOcom 3 to a properly earthed power source that is protected bya fuse.4.1.2 Start-up, radio receivingSelect channelHere, up to 38 channels can be set. A channel determines the assignment of aspecific ERGOremote to a specific ERGOcom 3.Here, it is expedient to select a channel corresponding to the treatment room: e.g.channel 1 is used for treatment room 1.▶ Hold down the Channel Selection / Learn Channel Mode button for < 2 seconds.The channel selected appears on the status display.NoteIf there is no input for 8 seconds, the ERGOcom 3 switches back to operationalmode.20/56
ERGOcom 34 Start-up | 4.1 Start-up▶ Select the required channel using navigation.NoteIf there is no input for 8 seconds, the ERGOcom 3 switches back to operationalmode.This saves the last setting on the status display.Learn channelThe ERGOremote 's radio code is synchronised with the channel configuredonERGOcom 3 .▶Hold down the Channel Selection button on ERGOcom 3 for more than 2 se-conds.Learn Channel Mode appears on the status display.NoteIf the channels do not synchronise within approx. 30 seconds, ERGOcom 3 swit-ches back to operational mode.▶Hold down the Wake Up/Learn button on the ERGOremote for more than 3 se-conds.The green LED will be lit for 3 seconds to show that synchronisation is complete.The green LED will flash to indicate that radio communication has not been set up.4.1.3 Start-up, USB driveTheERGOcom 3 with a display interface (equivalent to comfort or excellence level)has a built-in USB 2.0 drive. This drive shares volatile and non-volatile memory.The non-volatile memory then retains the information when the ERGOcom 3 isswitched off. The logos are stored here automatically.The images are automatically stored in the volatile memory. When theERGOcom 3 is switched off, these images are deleted.See also: 5.3.6 Generate still, Page 41The images contain the following name syntax: Bildxx_y.bmp.21/56
ERGOcom 34 Start-up | 4.1 Start-up▪ xx = image number 01 to 99▪ y = image number 1 to 4A maximum of 8 images may be saved. When a ninth image is saved, image 1 isautomatically overwritten.A KaVo company logo is stored on the USB drive at the time of delivery.Connect PCPrerequisite● Windows XP (Service Pack 1) or Windows 2000 must be installed on the PC.● The PC must have a free USB 2 interface.▶ Install Windows patch.NoteWhen installing theKaVo Device Interface System (using the enclosed CD), theUSB patch is installed automatically.If the KaVo Device Interface System is not installed, the USB patch can be in-stalled later from the CD D:\WINXP or downloaded and installed from the Microsofthomepage www.microsoft.com .▶Insert the USB cable to the ERGOcom 3 and the PC.The connection is made between the USB drive and the PC.Install own logo/image▶Convert the logo/image into a 720 x 576 dpi image format using image processingsoftware.22/56
ERGOcom 34 Start-up | 4.1 Start-up▶ Save this logo/image in bitmap format, giving it the filename USERLOGO.bmp.▶ Copy the file USERLOGO.bmp to the USB drive using the drag&drop function.The USB drive reports to the PC using the name ERGOCOM3.NoteThe ERGOcom 3 must not be switched off during transfer of the image (takesapprox. 20 seconds).You can set which logo/image is to be displayed in the OSD menu display interface.See also: 5.4.5 Menu point, other, Page 4923/56
ERGOcom 35 Operation | 5.1 Operation, general5 Operation5.1 Operation, general5.1.1 Switch on▶ Switch on main switch.These indicator lamps appear on the status display after open-shop testing:NoteIf the device is ready for operation, the current monitor image source is shown inthe display.5.1.2 Standby▶ Press the standby button.The standby LED lights up (blue).The status display and display are switched off and all device settings are retai-ned.▶ Press the standby button once again to leave Standby mode.NoteThis energy saving mode extends the service life of the status display and display.5.1.3 OSD menu, call ERGOcom 3In this menu, all settings can be defined for operation of the product.▶ Switch on main switch.▶While the status display shows "ERGOcom 3", activate the OSD menu until thefirst menu point appears.The OSD menu ERGOcom 3 is divided into 7 menu points:▪ Interface/wlink▪ Display-Format▪ RFpower24/56
ERGOcom 35 Operation | 5.1 Operation, general▪ System camera▪ Camera holder▪ USBpict.store▪ Store format▪ Mouse Z-Axis▪ Firmware version▪ Factory reset?NoteThe last 6 menu points are reserved for engineers.▶ Press the OSD menu button once again in order to return to operationalmode.5.1.4 OSD menu, operate ERGOcom 3▶ Select the required menu point using navigation.When you leave a menu point, its status display will be saved automatically.▶ Select the required setting using navigation.NoteIf there are no options available for a menu point, this navigation offers no functions.5.1.5 Menu pointsInterface? Represents component display interfaceMaterial number 1.002.9482.wlink represents component radio masterMaterial number 1.003.1318.OK represents the installation of the relevant option.Missing components can be added at any time.Setting of resolution and image frequency for the dis-play.SXGA/50 Hz or SXGA/60 Hz is 19" (1280 x 1024 dpi)XGA/50 Hz or XGA/60 Hz is 15" (1024 x 768 dpi)To ensure optimum image display quality, the samedisplay size (15" or 19") is to be used both in the cabinetarea and on the treatment device.00 is the default setting for 0 dBm transmitting power.At the same time, this is the maximum permitted trans-mitting power in the USA.01 represents 6 dBm transmitting power. This is themaximum permitted transmitting power in Europe. Ifthe transmitting power is not reliably sufficient, thetransmitting power can be increased using this.25/56
ERGOcom 35 Operation | 5.1 Operation, generalVarious setting parameters for image functions are of-fered on account of the various technical systems in theintraoral cameras ERGOcam 3 and ERGOcam 4 offe-red by KaVo. For optimum setting, the KaVo intraoralcamera built into the treatment device should be se-lected here.On: When the internal / external camera is taken out ofthe holder, the camera image is automatically dis-played on the monitor.Off: Automatic operations are not available. The came-ra image has to be selected manually.On: When saving in Video mode, the images are savedto the USB drive ERGOCOM3.Off: Nothing is saved to the USB drive ERGOCOM3.Determining the image format in which the images areto be saved to the USB drive.BMP stands for bitmap and is supported by all popularimage processing programs. The current YUV formatis converted to BMP beforehand (save time approx. 8seconds).YUV stands for video format and is supported by onlya few programs. However, this format is saved consi-derably more quickly (save time approx. 2 seconds).Here, whenERGOremote is used, the use of the Z-Axisof the joystick is determined.On: Clicking / double-clicking possible with the joystick.Off: Clicking / double-clicking not possible with the joy-stick.Display of Firmware version number of ERGOcom 3Mainboard.Reset all menu points to factory settings.CAUTION: VGA IN, VGA OUT, VIDEO IN and VIDEOOUT will also be reset to factory settings if you selectthis command.The factory settings are restored using Navigation up.26/56
ERGOcom 35 Operation | 5.2 Operation, no display interface (classic)5.2 Operation, no display interface (classic)Equivalent to ERGOcom 3 , classic level.In all subsequent descriptions, please note the following: to view the selected optionon Display 1, the relevant source must be active.5.2.1 Operational modeIn operational mode, it is possible to switch between VGA or VIDEO image sources,including audio, shown on KaVo Display 1.VGA IN - set image source▶ Press the VGA IN button.If a VIDEO image source was selected before, the last VGA IN image sourceselected will be shown in the status display.▶ Select the required VGA input by pressing the VGA IN button.27/56
ERGOcom 35 Operation | 5.2 Operation, no display interface (classic)See also:5.4.5 Menu point, other, Page 49VIDEO IN - set image sourcePrerequisite● A grabber card has to be installed in the PC in order to show video sources onDisplay 1.● VIDEO OUT 1 or VIDEO OUT 2 has to be connected to the grabber card.▶ Press the VIDEO IN button.If a VGA image source was selected before, the last VIDEO IN image sourceselected will be shown in the status display.28/56
ERGOcom 35 Operation | 5.2 Operation, no display interface (classic)▶ Select the required VIDEO input by pressing the VIDEO IN button.See also: 5.4.5 Menu point, other, Page 495.2.2 VGA OUT - set image source▶ Hold down the VGA OUT button for < 2 seconds.The last image source selected is shown in the status display. The status displayreturns to operational mode after 5 seconds.29/56
ERGOcom 35 Operation | 5.2 Operation, no display interface (classic)See also: 5.2.1 Operational mode, Page 27▶ Hold down the VGA OUT button for > 2 seconds.The status display flashes and setting mode is activated.▶ Use VGA OUT to select the required VGA input.NoteIf there is no input for 8 seconds, the ERGOcom 3 switches back to operationalmode.This saves the last setting on the status display.5.2.3 VIDEO OUT 1 - set image source30/56
ERGOcom 35 Operation | 5.2 Operation, no display interface (classic)▶ Hold down the VIDEO OUT 1 button for < 2 seconds.The last image source selected is shown in the status display. The status displayreturns to operational mode after 5 seconds.See also: 5.2.1 Operational mode, Page 27▶ Hold down VIDEO OUT 1 for > 2 seconds.The status display flashes and setting mode is activated.▶ Select the required VIDEO input by pressing the VIDEO OUT 1 button.NoteIf there is no input for 8 seconds, the ERGOcom 3 switches back to operationalmode.This saves the last setting on the status display.31/56
ERGOcom 35 Operation | 5.2 Operation, no display interface (classic)5.2.4 VIDEO OUT 2 - set image source▶ Hold down the VIDEO OUT 2 button for < 2 seconds.The last image source selected is shown in the status display. The status displayreturns to operational mode after 5 seconds.See also: 5.2.1 Operational mode, Page 27▶ Hold down the VIDEO OUT 2 button for > 2 seconds.The status display flashes and setting mode is activated.▶ Select the required VIDEO input by pressing the VIDEO OUT 2 button.32/56
ERGOcom 35 Operation | 5.2 Operation, no display interface (classic)NoteIf there is no input for 8 seconds, the ERGOcom 3 switches back to operationalmode.This saves the last setting on the status display.5.2.5 Generate stillPrerequisite● A video signal is shown on Display 1.●TheERGOcom 3 is connected to a PC fitted with a grabber card by means of aUSB cable.●On this PC, the KaVo Display Interface System software is installed.▶ Hold down the footswitch for < 2 seconds.The Generate still command is passed on to the PC.5.2.6 Save stillPrerequisite●TheERGOcom 3 is connected to a PC fitted with a grabber card by means of aUSB cable.●On this PC, the KaVo Display Interface System software is installed.▶ Hold down the footswitch for > 2 seconds.The Generate still command is passed on to the PC.33/56
ERGOcom 35 Operation | 5.2 Operation, no display interface (classic)5.2.7 Audio signalsThe audio signals will be linked synchronously to the relevant image signals.34/56
ERGOcom 35 Operation | 5.3 Operation, with display interface (comfort/excellence)5.3 Operation, with display interface (comfort/excellence)Equivalent to ERGOcom 3 , comfort or excellence level.In addition to excellence level, instructions for operation for the radio master(ERGOremote) can be found in the separate UI.See also: UIERGOremoteIn all subsequent descriptions, please note the following: to view the selected optionon Display 1, the relevant source must be active.5.3.1 Operational modeIn operational mode, it is possible to switch between VGA or VIDEO image sources,including audio, shown on KaVo Display 1.VGA IN - set image source▶ Press the VGA IN button.If a VIDEO image source was selected before, the last VGA IN image sourceselected will be shown in the status display.35/56
ERGOcom 35 Operation | 5.3 Operation, with display interface (comfort/excellence)▶ Select the required VGA input by pressing the VGA IN button.NoteIf no image source is connected to VIDEO IN 1/2, the logo set in the OSD menudisplay interface will be displayed.See also:5.4.5 Menu point, other, Page 49VIDEO IN - set image source▶ Press the VIDEO IN button.If a VGA image source was selected before, the last VIDEO IN image sourceselected will be shown in the status display.36/56
ERGOcom 35 Operation | 5.3 Operation, with display interface (comfort/excellence)▶ Select the required VIDEO input by pressing the VIDEO IN button.NoteIf no image source is connected to VIDEO IN 1/2, the logo set in the OSD menudisplay interface will be displayed.See also:5.4.5 Menu point, other, Page 495.3.2 VGA OUT - set image source▶ Hold down the VGA OUT button for < 2 seconds.The last image source selected is shown in the status display. The status displayreturns to operational mode after 5 seconds.37/56
ERGOcom 35 Operation | 5.3 Operation, with display interface (comfort/excellence)See also: 5.2.1 Operational mode, Page 27▶ Hold down the VGA OUT button for > 2 seconds.The status display flashes and setting mode is activated.▶ Use VGA OUT to select the required VGA input.NoteIf there is no input for 8 seconds, the ERGOcom 3 switches back to operationalmode.This saves the last setting on the status display.5.3.3 VIDEO OUT 1 - set image source38/56
ERGOcom 35 Operation | 5.3 Operation, with display interface (comfort/excellence)▶ Hold down the VIDEO OUT 1 button for < 2 seconds.The last image source selected is shown in the status display. The status displayreturns to operational mode after 5 seconds.▶ Hold down VIDEO OUT 1 for > 2 seconds.The status display flashes and setting mode is activated.▶ Select the required VIDEO input by pressing the VIDEO OUT 1 button.39/56
ERGOcom 35 Operation | 5.3 Operation, with display interface (comfort/excellence)5.3.4 VIDEO OUT 2 - set image source▶ Hold down the VIDEO OUT 2 button for < 2 seconds.The last image source selected is shown in the status display. The status displayreturns to operational mode after 5 seconds.See also: 5.2.1 Operational mode, Page 27▶ Hold down the VIDEO OUT 2 button for > 2 seconds.The status display flashes and setting mode is activated.▶ Select the required VIDEO input by pressing the VIDEO OUT 2 button.40/56
ERGOcom 35 Operation | 5.3 Operation, with display interface (comfort/excellence)NoteIf there is no input for 8 seconds, the ERGOcom 3 switches back to operationalmode.This saves the last setting on the status display.5.3.5 Audio signalsThe audio signals will be linked synchronously to the relevant image signals.5.3.6 Generate stillPrerequisiteA video signal is shown on Display 1.▶ Hold down the Freeze button for < 2 seconds.A still is generated on Display 1 from the current video image.or▶ Hold down the footswitch for < 2 seconds.A still is generated on Display 1 from the current video image.▶ Press the Freeze button again to return to live image display and activate thenext image (1-4) as a live image.41/56
ERGOcom 35 Operation | 5.3 Operation, with display interface (comfort/excellence)or▶ Press the footswitch again to return to live image display and activate the nextimage (1-4) as a live image.5.3.7 Save stillPrerequisite●TheERGOcom 3 is connected to a PC fitted with a grabber card by means of aUSB cable.●On this PC, the KaVo Display Interface System software is installed.▶ Hold down the Freeze button for > 2 seconds.The successful save is indicated on Display 1 with save.or▶ Hold down the footswitch for > 2 seconds.The successful save is indicated on Display 1 with save.NoteSaving the active image (image number is white) is possible in Full Screen andQuad mode for the display.The still is saved on the PC and on the internalERGOcom 3 USB drive as long ason is selected for USBpict.store.See also: 5.1.5 Menu points, Page 255.3.8 Change display viewPrerequisiteA video signal is shown on Display 1.Images on Display 1 can be toggled between Full Screen mode and Quad mode.▶ Press the Full Screen /Quad Mode button.42/56
ERGOcom 35 Operation | 5.3 Operation, with display interface (comfort/excellence)NoteThe image number of the active image is shown in white.▶ Press the Full Screen / Quad Mode button again to return to Full Screen mode.5.3.9 Select imagePrerequisiteThe image selected must be a still.▶ Select the required image using the 4 navigation buttons.The still selected is retained as a still.▶ Press the Freeze button.The still selected is deleted or turned into a live image.or▶ Press the footswitch.The still selected is deleted or turned into a live image, and the next image numberis selected automatically.NoteIf this function is not required, the Freeze button has to be used for image selectionon theERGOcom 3 .43/56
ERGOcom 35 Operation | 5.3 Operation, with display interface (comfort/excellence)5.3.10 Delete image / imagesNotePossible in Full Screen and Quad mode.ERGOcom 3PrerequisiteThe image selected must be a still.▶ Hold down the Delete image / images button for < 2 seconds.The still is deleted and the logo selected in the OSD menu display interface isshown.See also:5.4.5 Menu point, other, Page 49▶ Hold down the Delete image / images button for > 2 seconds.All 4 stills are deleted and the logo selected in the OSD menu display interfaceis shown.Multi footswitch controlPrerequisite4 stills are generated using the multi footswitch control.See also: 5.3.6 Generate still, Page 41▶ Press the footswitch again.Display 1 shows the prompt "Delete all images?"▶ Hold down the footswitch for > 2 seconds to delete all 4 stills.The logo set in the OSD menu display interface is inserted.or▶ Hold down the footswitch for < 2 seconds to switch image 1 to a live image.44/56
ERGOcom 35 Operation | 5.3 Operation, with display interface (comfort/excellence)5.3.11 Change image sourcePrerequisiteA still has to be generated.See also: 5.3.6 Generate still, Page 41▶ Put the camera in the holder.▶ Press the footswitch.TheERGOcom 3 switches to the image source selected before the camera wasremoved.45/56
ERGOcom 35 Operation | 5.4 Operation, OSD menu display interface5.4 Operation, OSD menu display interfaceThe overview diagrams were structured according to the type of image source andthe connected function:VGA main menu Overview of main menu with VGA IN 1 or VGA IN 2image source.VIDEO main menu Overview of main menu with CAMERA, VIDEO IN 1 orVIDEO IN 2 image source.Menu point, other This menu point is the same for all image sources.5.4.1 Call OSD menu display interfacePrerequisiteThe image source for which the display settings are to be changed must be selec-ted.See also:5.2.1 Operational mode, Page 275.3.1 Operational mode, Page 35▶ Press the OSD menu button.The OSD menu display interface is inserted on Display 1.▶ Press OSD menu again to leave the menu.5.4.2 Operate OSD menu display interfacePrerequisiteThe OSD menu display interface was called.Navigation FunctionScroll in the current menu window. The menu point se-lected will have a coloured background.Select the menu point or setting to be changed.The setting that can be changed is white.Leave the selected menu point orsetting.46/56
ERGOcom 35 Operation | 5.4 Operation, OSD menu display interfaceNavigation FunctionChange settings.Save changed setting.Reset the selected menu point.5.4.3 VGA main menuThere is a separate main menu for every VGA IN image source. This allows thesettings on Display 1 to be defined and saved for every image source.NoteThe requisite explanations of the individual menu points or settings are inserteddirectly on Display 1.47/56
ERGOcom 35 Operation | 5.4 Operation, OSD menu display interface5.4.4 VIDEO main menuThere is a separate main menu for every VIDEO IN image source. This allows thesettings on Display 1 to be defined and saved for every image source.NoteThe requisite explanations of the individual menu points or settings are inserteddirectly on Display 1.48/56
ERGOcom 35 Operation | 5.4 Operation, OSD menu display interface5.4.5 Menu point, otherThis menu point is available in all main menus (VGA and VIDEO). However, it is notsaved separately for all menus, but only once, covering all menus.NoteThe requisite explanations of the individual menu points or settings are inserteddirectly on Display 1.49/56
ERGOcom 35 Operation | 5.4 Operation, OSD menu display interface50/56
ERGOcom 36 Preparation methods DIN EN ISO 17664 | 6.1 Cleaning6 Preparation methods DIN EN ISO 176646.1 Cleaning6.1.1 Exterior cleaning by handThe wide variety of drugs and chemicals used in dental practice means that damagemay occur to painted surfaces or plastics if anything is allowed to drip onto them.Tests have shown that surfaces cannot be protected entirely against all substancesavailable on the market.As damage to surfaces is very much dependent on the reaction times of these sub-stances, it is essential for any spilled substances to be wiped away immediatelyusing a damp cloth.Detergent recommended: KaVo Elastoclean.The following detergents must not be used:1. Strongly alkaline lyes2. Acids3. Detergents containing fluoride4. Detergents containing ammonia5. All kinds of scouring agent▶Switch off Display 1 and ERGOcom 3 .CAUTIONDamage caused by fluids.Faults in electrical components.▶ Protect device openings from the penetration of fluids.▶ Use a soft cloth and mild cleaning fluid to clean the surface.51/56
ERGOcom 36 Preparation methods DIN EN ISO 17664 | 6.2 Disinfection6.2 DisinfectionCAUTIONDamage caused by fluids.Faults in electrical components.▶ Protect device openings from the penetration of fluids.▶ Wipe surface with a soft, fluff-free cloth to disinfect them.NoteContaminated parts must be disinfected after every patient.52/56
ERGOcom 36 Preparation methods DIN EN ISO 17664 | 6.3 Maintenance6.3 MaintenanceThe product does not require regular user maintenance.53/56
ERGOcom 37 Safety checks7 Safety checksIf an EC3 Display is integrated with an ERGOcom 3 , safety checks (SFC) must beperformed every 2 years. A detailed description of SFC can be found in theengineer's instructions.See also: EIERGOcom 354/56
ERGOcom 38 Troubleshooting8 TroubleshootingFault Cause RemedyNo status display. ERGOcom 3 switched to standby. ▶ Leave Standby mode.See also: 5.1.2 Standby, Page 24ERGOcom 3 off. ▶ERGOcom 3 on.Mains fuse burnt out. ▶ Test mains fuse and replacewhere necessary.ERGOcom 3 switches itself off andcannot be switched back on imme-diately.Overheating. ▶ Ensure good ventilation for theERGOcom 3 .See also: 4 Start-up, Page 20Everything has stopped working. Mains failure / overvoltage. ▶ ERGOcom 3 to be switched offand then switched on again after5 seconds.Access to USB hardware does notwork under Windows XP.The Microsoft patch needed to ope-rate the USB port is not installed onthe target computer.▶ Install the required patch.This can be done while installingthe CCCDIS.See also: 4.1.3 Connect PC , Page22Selected image source (e.g. DVDplayer) is not displayed.The DVD player is switched off, orno DVD has been inserted.▶ Check image source.No camera image is displayed. Treatment unit switched off. ▶ Switch on treatment unit.Poor video quality. Poor image material. ▶ Only use image material that is ofgood quality.Poor PC image source quality. Display setting for graphics card notthe same as the display format set-ting on the ERGOcom 3 .▶ Adjust display format and gra-phics card setting.See also: 5.1.5 Menu points,Page 25Poor image quality. Incorrect settings in the OSD menudisplay interface.▶ Improve the image quality usingthe options in the OSD menu.See also: 5.4 Operation, OSD me-nu display interface, Page 4655/56
ERGOcom 39 Glossary9 GlossaryTerm DescriptionDisplay 1 Display 1 is the display connected via the VGA Monitorinterface and installed on the lamp mounting rod.Display 2 Display 2 is the display connected via the VGA out in-terface.Full screen mode The image is displayed across the entire display area.Quad mode Four independent images are shown in the display.OSD menu display inter-faceThe OSD menu of the display interface. This is con-trolled viaERGOcom 3 and shown in Display 1.OSD menu, ERGOcom 3 The ERGOcom 3-specific OSD menu. This is shown inthe status display.OSD menu, Display 1 The EC3 Display-specific OSD menu. This is controlledand shown in the display.56/56
1.003.1609 · Ma · 08.04-01 · EN
User instructionsERGOremoteAlways on the safe side.
Sales and Distribution:KaVo Dental GmbHBismarckring 39D-88400 BiberachTel.: ++ 49 / 73 51/ 56 - 0Fax: ++ 49 / 73 51 / 56 – 14 88Manufacturer:Kaltenbach & Voigt GmbHBismarckring 39D-88400 Biberach
User instructions ERGOremoteTable of contentsTable of contentsTable of contents ..............................................................................................................................................1 1 User Notes .....................................................................................................................................................3 1.1 User guidelines ........................................................................................................................................3 1.1.1 Abbreviations ..................................................................................................................................3 1.1.2 Symbols ..........................................................................................................................................3 1.2 Target audience .......................................................................................................................................4 1.3 Service .....................................................................................................................................................5 1.4 Provisions of guarantee ...........................................................................................................................6 1.5 Transport and storage ..............................................................................................................................7 1.5.1 The German packaging ordinance, 28 August 1998 ......................................................................7 1.5.2 Damage in transit ............................................................................................................................7 1.5.3 Storage ...........................................................................................................................................8 2 Safety .............................................................................................................................................................9 2.1 Description of safety instructions .............................................................................................................9 2.1.1 Hazard warning symbol ..................................................................................................................9 2.1.2 Structure .........................................................................................................................................9 2.1.3 Description of the different levels of hazard ....................................................................................9 2.2 Intended purpose ...................................................................................................................................10 2.2.1 General .........................................................................................................................................10 2.2.2 Product-specific ............................................................................................................................10 2.3 Safety instructions ..................................................................................................................................11 2.3.1 General .........................................................................................................................................11 3 Product description ......................................................................................................................................12 3.1 ERGOremote .........................................................................................................................................12 3.2 Rating plate ............................................................................................................................................13 3.3 Technical data ........................................................................................................................................14 4 Start-up ........................................................................................................................................................15 4.1 Insert battery ..........................................................................................................................................15 4.2 Learn channel ........................................................................................................................................16 5 Operation .....................................................................................................................................................17 5.1 Controls/displays ....................................................................................................................................17 5.1.1 Synchronise the ERGOremote to ERGOcom 3 ............................................................................17 5.1.2 Wake Up .......................................................................................................................................17 5.1.3 Sleep mode ...................................................................................................................................17 5.1.4 Send and receive status ...............................................................................................................17 5.1.5 Reset .............................................................................................................................................17 5.1.6 Delete image in Video mode .........................................................................................................18 5.1.7 Quad mode in Video mode ...........................................................................................................18 5.1.8 Freeze in Video mode ...................................................................................................................18 5.1.9 OSD Display Interface ..................................................................................................................19 5.1.10 Cursor keys .................................................................................................................................19 5.1.11 Video Input 2 to Display 1 ...........................................................................................................20 5.1.12 Video Input Camera to Display 1 ................................................................................................20 5.1.13 Video Input 1 to Display 1 ...........................................................................................................20 5.1.14 VGA Input 2 to Display 1 .............................................................................................................20 5.1.15 VGA Input 1 to Display 1 .............................................................................................................20 5.1.16 Standby .......................................................................................................................................20 5.1.17 Battery warning ...........................................................................................................................20 1/25
User instructions ERGOremoteTable of contents6 Preparation methods DIN EN ISO 17664 ....................................................................................................22 6.1 Cleaning .................................................................................................................................................22 6.1.1 Exterior cleaning by hand .............................................................................................................22 6.2 Disinfection ............................................................................................................................................23 6.3 Maintenance ..........................................................................................................................................24 7 Glossary .......................................................................................................................................................25 2/25
User instructions ERGOremote1 User Notes | 1.1 User guidelines1 User Notes1.1 User guidelinesPrerequisitePlease read these instructions before using the product to avoid operator error anddamage.1.1.1 AbbreviationsAbbre‐viationMeaningUI User instructionsSI Setup instructionsSTI Service Technician's instructionsSFC Safety checksIEC International Electrotechnical Commission1.1.2 SymbolsSee Safety/Hazard Warning Symbol chapterImportant information for users and Service TechniciansThermally disinfectableSterilisable up to 135°CCE (Communauté Européenne) marking. Products bearing this markingconform to the requirements of the pertinent EC directives (applicable Eu‐ropean standards).Action promptLaser hazard warning signLaser signESD - warning message3/25
User instructions ERGOremote1 User Notes | 1.2 Target audience1.2 Target audienceThis document is intended for use by dentists and other dental practice employees.4/25
User instructions ERGOremote1 User Notes | 1.3 Service1.3 ServicePlease send all questions about the product, services and maintenance to the fol‐lowing addresses.Always quote product serial number in any correspondence.KaVo Dental GmbHAfter Sales ServiceBahnhofstraße 20D-88445 Warthausen0049 - (0) 7351-56 27000049 - (0) 7351-18218multimedia@kavo.dewww.kavo.comKaVo Präsentations- und Servicezentrum Frankfurt (KaVo Presentation and Ser‐vice Center, Frankfurt)Hungener Straße 6-1260389 Frankfurt069 - 5 97 03 -94 / 95KaVo Präsentations- und Servicezentrum Hamburg (KaVo Presentation and Ser‐vice Center, Hamburg)Sachsenstraße 520097 Hamburg040 - 23 44 -77/ - 78KaVo Präsentations- und Servicezentrum Düsseldorf (KaVo Presentation and Ser‐vice Center, Düsseldorf)Kaiserswerther Straße 3540477 Düsseldorf0211 - 49 91 -38 / -39KaVo Präsentations- und Servicezentrum Berlin (KaVo Presentation and ServiceCenter, Berlin)Uhlandstraße 20-2510623 Berlin030 - 7 91 94 84KaVo Präsentations- und Servicezentrum LeipzigZweenfurther Straße 904827 Leipzig-Gerichshain03 42 92 - 7 41 -12/ -135/25
User instructions ERGOremote1 User Notes | 1.4 Provisions of guarantee1.4 Provisions of guaranteeThe KaVo end customer guarantee for the product named in the completion certi‐ficate guarantees that the product functions correctly and that there are no faults inthe material or workmanship for a duration of 12 months following the purchase date,according to the following conditions:Following a reasonable complaint relating to defects or short delivery, KaVo gua‐rantee to provide a replacement or perform repairs, whichever they deem mostsuitable. Claims of any other nature, damages in particular, are excluded. In caseof default and gross negligence or intent, the latter only applies if there are no com‐pelling legal provisions opposing it.KaVo shall not be liable for defects and their consequences, which occur as a resultof normal wear and tear, or of improper cleaning or maintenance.Non-observance of the operating, maintenance or connection regulations; calcina‐tion or corrosion; impurities in the air and water supply; or chemical or electricaleffects, which are non-standard or not permitted according to company regulations.As a general rule, this guarantee does not apply to lamps, glassware, rubber partsor the colour durability of synthetic materials.KaVo shall not be liable for defects or their consequences if they are likely to be adirect result of actions or modifications by a customer or third party.Any claims arising from this guarantee can only be lodged if the completion certifi‐cate (carbon copy) has been sent in to KaVo and the operator/user is able to producethe original.6/25
User instructions ERGOremote1 User Notes | 1.5 Transport and storage1.5 Transport and storageNoteWhen transporting used units that are already covered in dust, completely seal theextraction vent at the rear of the unit (e.g. using suitable adhesive tape).1.5.1 The German packaging ordinance, 28 August 1998NoteApplies only to the Federal Republic of Germany.KaVo transport packaging is disposed of and recycled by local waste managementand recycling companies under Germany's Dual System.For more information about waste management and recycling, and for up-to-datelists of local waste management and recycling companies, visit the following sites:http://www.umweltdatenbank.dehttp://www.quality.deAny KaVo transport packaging that customers return to KaVo, at the customer's ownexpense, shall be forwarded to the appropriate recycling companies at no extra costand with no reimbursement.1.5.2 Damage in transitWithin GermanyIf the outer packaging is noticeably damaged upon delivery, the following proceduremust be adhered to:1. The recipient must record the loss or damage on the notice of receipt. The reci‐pient and transport company employee delivering the product must both sign thenotice of receipt.2. Leave the product and packaging in the condition they arrived in.3. Do not use the product.4. Report the damage to the transport company.5. Report the damage to KaVo.6. Under no circumstances should you return the damaged product to KaVo withoutprior consultation.7. Send the signed notice of receipt to KaVo.If the product is damaged without there being any noticeable damage to the packa‐ging upon delivery, you must proceed as follows:1. Report the damage to the transport company as soon as possible within 7 daysof delivery.2. Report the damage to KaVo.3. Leave the product and packaging in the condition they arrived in.4. Do not use the damaged product.NoteIf the recipient fails to adhere to any of the procedures mentioned above, the da‐mage shall be considered as having arisen after delivery (pursuant to Germany'sGeneral Terms and Conditions for Carriers (ADSp.), Article 28).7/25
User instructions ERGOremote1 User Notes | 1.5 Transport and storageOutside GermanyNoteKaVo shall not be liable for damage caused in transit.Check the shipment immediately upon delivery!If the outer packaging is noticeably damaged upon delivery, the following proceduremust be adhered to:1. The recipient must record the loss or damage on the notice of receipt. The reci‐pient and transport company employee delivering the product must both sign thenotice of receipt.The recipient may claim damages against the transport company only on thebasis of these recorded facts.2. Leave the product and packaging in the condition they arrived in.3. Do not use the product.If the product is damaged without there being any noticeable damage to the packa‐ging upon delivery, you must proceed as follows:1. Report the damage to the transport company as soon as possible within 7 daysof delivery.2. Leave the product and packaging in the condition they arrived in.3. Do not use the damaged product.NoteIf the recipient fails to adhere to any of the procedures mentioned above, the da‐mage shall be considered as having arisen after delivery (pursuant to theConvention on the Contract for the International Carriage of Goods by Road (CMR)Chapter V Article 30).1.5.3 StorageNoteSave packaging in case product requires sending away for servicing or repairs.The symbols printed on the outer packaging apply to transportation and storage;their meanings are as follows:Keep upright in transit; this way up!Handle with careKeep dryStacking limitation.Temperature limitations.8/25
User instructions ERGOremote2 Safety | 2.1 Description of safety instructions2 Safety2.1 Description of safety instructions2.1.1 Hazard warning symbolHazard warning symbol2.1.2 StructureDANGERThe introduction describes the type and source of the danger.This section shows what could happen if the instructions are not followed.▶ The optional action shows what measures to take to avoid danger.2.1.3 Description of the different levels of hazardTo avoid personal and material injury, safety instructions within this document areclassified into three levels of hazard.CAUTIONCAUTIONIndicates a potentially dangerous situation which could result in material damage,minor personal injury or non-severe personal injury.WARNINGWARNINGIndicates a potentially dangerous situation which could result in fatal injury or se‐vere personal injury.DANGERDANGERThis is the highest level of hazard. It indicates an imminently dangerous situationwhich could result in fatal injury or severe personal injury.9/25
User instructions ERGOremote2 Safety | 2.2 Intended purpose2.2 Intended purpose2.2.1 GeneralThe operator is required to make sure that the device is in a fully functional and safecondition before commencing use.The appropriate, comprehensive guidelines for this product and/or national laws,national regulations and technlogical rules for starting up and operating have to beapplied and fulfilled in line with the specified, intended purpose of the KaVo product.NoteDispose of or recycle the waste materials produced without endangering humanhealth or the environment and under observance of the applicable national regu‐lations that are in place.Should you have any questions relating to the proper disposal of the KaVo product,please contact your nearest KaVo office.2.2.2 Product-specificThe ERGOremote remote control is for controlling ERGOcom 3 and/or for controllinga computer by mouse.It is a medical device accessory (protection class 1) for use within the patient envi‐ronment of dental practices.10/25
User instructions ERGOremote2 Safety | 2.3 Safety instructions2.3 Safety instructions2.3.1 GeneralThis KaVo product is not permitted for use in areas where there is a risk of explosion.WARNINGInjuries or harm caused by damaged functional components.Damaged functional components can cause personal harm or injury.▶ If functional components are damaged: Stop work, remedy the problem or informthe Service Technician.CAUTIONMalfunction due to electromagnetic fields.This product meets all the requirements that are in effect relating to electromagneticfields. Due to the complex interference between mobile phones and medical devi‐ces, it is not, however, possible to completely exclude the possibility of the productbeing affected by a functioning mobile phone.▶ Refrain from using mobile phones in the practice and clinic area!▶ Turn off electronic equipment, such as data memories, hearing aids etc, duringoperation!CAUTIONRisks caused by electromagnetic fieldsElectromagnetic fields may interfere with the functions of implanted systems (suchas pacemakers).▶ Consult the patient before treatment!CAUTIONDamage caused by fluids.Faults in electrical components.▶ Protect product openings from the penetration of fluids.The following individuals are authorised to repair and maintain the KaVo product:▪ Service Technicians from KaVo offices.▪ Service Technicians working for KaVo authorised dealers, specially trained byKaVo.11/25
User instructions ERGOremote3 Product description | 3.1 ERGOremote3 Product description3.1 ERGOremote1Delete Image/Call ERGOcom 3 Con‐trol10Standby/On2LED Radio Communication11VGA Input 1 to Display 13Wake Up/Learn12Video Input 1 to Display 14Freeze13Video Input Camera to Display 15Mouse/Joystick14Left6Right15Up7Down16OSD8Video Input 2 to Display117Quad mode9VGA Input 2 to Display 112/25
User instructions ERGOremote3 Product description | 3.2 Rating plate3.2 Rating plateType ERGOremotePurchase order no. 1.003.0539Serial no. nnnnnnDL123+++ Battery and polarity labelling13/25
User instructions ERGOremote3 Product description | 3.3 Technical data3.3 Technical dataWave band ISM 2.4 GHzNumber of channels 38Maximum range without obstructions typically 100 mRange in room < 20 mRadiated power < 5 mWSleep mode < 10 µAStandby typically 3 mASend operation typically 100 mAReceive operation typically 80 mAEN 300,440-1-2 Use of product spectrumEN 301,489-1 EMCEN 60950 Safety and low voltage directiveAuthorisation according to R&TTE, FCC14/25
User instructions ERGOremote4 Start-up | 4.1 Insert battery4 Start-up4.1 Insert batteryNoteA DL 123 battery is supplied with the equipment.Only use original batteries. We cannot provide a functional guarantee for otherbatteries.▶ Remove screw to open battery compartment.▶ Insert the battery correctly in the compartment (in line with pole labels).15/25
User instructions ERGOremote4 Start-up | 4.2 Learn channel4.2 Learn channelThe ERGOremote 's radio code is synchronised with the channel configuredonERGOcom 3 .▶ Hold down the Channel Selection button on ERGOcom 3 for more than 2 se‐conds.Learn Channel Mode appears on the status display.NoteIf the channels do not synchronise within approx. 30 seconds, ERGOcom 3 swit‐ches back to operational mode.▶ Hold down the Wake Up/Learn button on the ERGOremote for more than 3 se‐conds.The green LED will be lit for 3 seconds to show that synchronisation is complete.The green LED will flash to indicate that radio communication has not been set up.16/25
User instructions ERGOremote5 Operation | 5.1 Controls/displays5 Operation5.1 Controls/displays5.1.1 Synchronise the ERGOremote to ERGOcom 3NoteChannel 1 is set as a default. If there are a number of different ERGOremoteand ERGOcom 3 instruments in use at the practice, a different channel must beset and the associated learning procedure completed in every room of the practice.▶ Switch on Learn mode on ERGOcom 3 .See also:4.2 Learn channel, Page 165.1.2 Wake Up▶ Before using the ERGOremote, press the Wake Up button or any other functionbutton (apart from the joystick.)The LED is lit up for approx. 3 seconds.An internal calibration is run during this period. The joystick must not be movedabout. All the other functions are available immediately.5.1.3 Sleep modeOnce the buttons or joystick have been operated, ERGOremote remains in an ope‐rative state for approx. 30 seconds. Once this 30 seconds is up, ERGOremoteautomatically returns to sleep mode.5.1.4 Send and receive statusThe green LED acknowledges every active send and receive operation.5.1.5 ResetIf the green LED is constantly flashing, this indicates a disruption in the radio link.To remedy the disruption, reset the instrument.17/25
User instructions ERGOremote5 Operation | 5.1 Controls/displays▶ Press the Standby button.The right, left, up and down button functions are reset.NoteERGOcom 3 and the ERGOcom 3 display switch to Standby mode.5.1.6 Delete image in Video modeYou can use the cursor buttons to navigate from one image to another. A brighterimage number indicates which image is active.▶ Press delete.The active image in Quad or Full Screen mode is deleted.5.1.7 Quad mode in Video modeYou use this button to toggle between Full Screen and Quad mode.5.1.8 Freeze in Video modeGenerate still▶ Press the Freeze button.The activated image is frozen.Return to live image▶ Hold down Freeze button for less than 3 seconds.The still switches back to a live image.Save still▶ Hold down Freeze button for more than 3 seconds.The still is saved in the USB memory of ERGOcom 3 or on the PC, dependingon the minimum system requirements.18/25
User instructions ERGOremote5 Operation | 5.1 Controls/displays5.1.9 OSD Display Interface▶ Press the OSD button.The On Screen Display appears.See also: ERGOcom 3 Instructions for Use5.1.10 Cursor keysJoystickPrerequisiteThe corresponding PC is connected via the USB interface of ERGOcom 3 .The joystick can be used to move the cursor on the PC interface.If the z axis in ERGOcom 3 is activated, you can perform click and double-clickfunctions by placing axial pressure on the joystick.UpIn VGA mode, the up button is used to scroll through active menus.In Video mode and OSD (Display Interface) mode, it can be used to navigate bet‐ween the four images.RightIn VGA mode, the right button is used to control the cursor - equivalent to the right-hand mouse button.In Video mode and OSD (Display Interface) mode, it can be used to navigate bet‐ween the four images.LeftIn VGA mode, the left button is used to control the cursor - equivalent to the left-hand mouse button.In Video mode and OSD (Display Interface) mode, it can be used to navigate bet‐ween the four images.19/25
User instructions ERGOremote5 Operation | 5.1 Controls/displaysDownIn VGA mode, the down button is used to scroll through inactive menus.In Video mode and OSD (Display Interface) mode, it can be used to navigate bet‐ween the four images.5.1.11 Video Input 2 to Display 1This button is used to switch the incoming image signal at Video Input 2 Directly toDisplay 1.5.1.12 Video Input Camera to Display 1This button is used to switch the incoming image signal at the Video Input Cameradirectly to Display 1.5.1.13 Video Input 1 to Display 1This button is used to switch the incoming image signal at Video 1 directly to Display1.5.1.14 VGA Input 2 to Display 1This button is used to switch the associated image contents at VGA Input 2 directlyto Display 1.5.1.15 VGA Input 1 to Display 1This button is used to switch the associated image contents at VGA Input 1 directlyto Display 1.5.1.16 StandbySelect this button to switch ERGOcom 3 and Display 1 over to power saving mode.This saves power and prolongs the life cycles of the instruments.5.1.17 Battery warningOnce the ERGOremote has undergone a certain length of operation, it will becomenecessary to change its energy source. This is monitored by the instrument.20/25
User instructions ERGOremote5 Operation | 5.1 Controls/displaysIf the cell voltage falls below the level required for safe operation, the red LED willflash for approximately 3 seconds after wake-up indicating that the battery needsreplacing.21/25
User instructions ERGOremote6 Preparation methods DIN EN ISO 17664 | 6.1 Cleaning6 Preparation methods DIN EN ISO 176646.1 Cleaning6.1.1 Exterior cleaning by handThe wide variety of drugs and chemicals used in dental practice means that damagemay occur to painted surfaces or plastics if anything is allowed to drip onto them.Tests have shown that surfaces cannot be protected entirely against all substancesavailable on the market.As damage to surfaces is very much dependent on the reaction times of these sub‐stances, it is essential for any spilled substances to be wiped away immediatelyusing a damp cloth.Detergent recommended: KaVo Elastoclean.The following detergents must not be used:1. Strongly alkaline lyes2. Acids3. Detergents containing fluoride4. Detergents containing ammonia5. All kinds of scouring agentCAUTIONDamage caused by fluids.Faults in electrical components.▶ Protect product openings from the penetration of fluids.▶ Use a soft cloth and mild cleaning fluid to clean the surface.22/25
User instructions ERGOremote6 Preparation methods DIN EN ISO 17664 | 6.2 Disinfection6.2 DisinfectionCAUTIONDamage caused by fluids.Faults in electrical components.▶ Protect product openings from the penetration of fluids.▶ Wipe surface with a soft, fluff-free cloth to disinfect them.23/25
User instructions ERGOremote6 Preparation methods DIN EN ISO 17664 | 6.3 Maintenance6.3 MaintenanceThe product does not require regular user maintenance.24/25
User instructions ERGOremote7 Glossary7 GlossaryTerm DescriptionDisplay 1 Display 1 is the display connected via the VGA Monitorinterface and installed on the lamp mounting rod.Display 2 Display 2 is the display connected via the VGA out in‐terface.Full screen mode The image is displayed across the entire display area.Quad mode Four independent images are shown in the display.OSD menu display inter‐faceThe OSD menu of the display interface. This is con‐trolled via ERGOcom 3 and shown on Display 1.OSD menu, ERGOcom 3 The ERGOcom 3-specific OSD menu. This is shown inthe status display.OSD menu, Display 1 The ERGOcom 3 display-specific OSD menu. This iscontrolled and shown in the display.25/25
1.003.1631 · hw · 31.01.2005 - 02 · en

Navigation menu